Emergency Call
Contents
1. w 1 PANEL DESCRIPTION E Function display O SIGNAL STRENGTH INDICATOR Displays the relative receive signal strength level LOW POWER ICON Appears when low output power is selected e When the battery charge decreases to a set level low power is automatically selected AUDIBLE ICON Appears when the channel is in the audible unmuted mode Appears when a matched 2 Tone or 5 Tone is re ceived COMPANDER ICON Appears when the Compander function is ON SCRAMBLER ICON Appears when the Voice Scrambler function is ON BELL ICON Appears or blinks when a matched 2 Tone or 5 Tone is received depending on the presetting SCAN ICON Appears or blinks while scanning KEY LOCK ICON Appears when the Key Lock function is ON BATTERY INDICATOR Displays the remaining battery charge Blinks when the battery charge decreases to a set level ALPHANUMERIC READOUT Displays messages such as channel text LED indicator The LED indicator indicates the status of various parameters of the transceiver as follows Reference R Red G Green O Orange e Cloning reading or writing data e Cloning Error if cloning fails JE c TRY c RY R e RS RTS ee PRS e Inh Blank CH Unlocked when you cannot use the channel e TX Low Battery 2 while transmitting e TX Low Battery 1 while transmitting e Transmitting jo o l e Scanning PANEL DESCR2. Push to start and cancel a scan e When a scan is started with the Power ON Scan or Auto matic scan function push this key to cancel it The can celled scan resumes after a set time period lt for the Simple type and 10 key type transceivers gt Push to start and cancel a scan To select the scan group hold down this key to display scan groups then push CH Up or CH Down to select a desired group SCAN ADD DEL TAG only for the Simple type and 10 key type transceivers Push to add the operating channel to or delete it from the scan group 1 Hold down to display the scan group then push CH Up or CH Down to select the desired one 2 Push to add the channel to or delete it from the select ed scan group 3 Hold down to exit the scan list selection mode While a scan is paused on a non priority channel push this key to delete the selected channel from the scan group Y Depending on the presetting the cleared channel may ZY be automatically added to the scan group again after Z the scan is cancelled PRIORITY A CHANNEL PRIORITY B CHANNEL Push to select the Priority A or Priority B channel PRIORITY A CHANNEL REWRITE PRIORITY B CHANNEL REWRITE Push to select the Priority A or Priority B channel Hold down Prio A Rewrite or Prio B Rewrite to as sign the operating channel to Priority A or Priority B chan nel respectively MEMORY CHANNELS 1 2 3 4 Push to direc
3. 7 1 PANEL DESCRIPTION C Tone CH ENT only for the Simple type and 10 key type transceivers Push to enter the continuous tone selection mode Select the tone frequency or DTCS code using CH Up or CH Down TALK AROUND Push to turn the Talk Around function ON or OFF e The Talk Around function equalizes the transmit frequen cy to the receive frequency for transceiver to transceiver communication WIDE NARROW Push to toggle the channel passband width between wide and narrow DTMF AUTODIAL lt for the Non display type transceivers gt Push to transmit the preprogrammed DTMF code lt for the Simple type and 10 key type transceivers gt Push to enter the DTMF number selection mode Then se lect a DTMF number by pushing CH Up or CH Down After selecting the DTMF channel push again to transmit the selected DTMF code RE DIAL Push to transmit the last transmitted DTMF code 4 NOTE TX memories are cleared after turning OFF the 4 transceiver CALL Push to transmit a 2 Tone or 5 Tone in the operating chan nel CALL A CODE 1 CODE B CODE 2 only for the LMR model Push to transmit a 2 Tone that is programmed in channel 1 Code A or channel 2 Code B CALL A CODE 30 CODE B CODE29 only for the PMR model Push to transmit a 5 Tone as a station code that is pro grammed in channel 30 Code A or channel 29 Code B EMERGENCY Hold down during the Eme
4. E User set mode Backlight The User Set mode enables you to change various settings e ON Always lit You can customize the transceiver operation to suit your e AUT Lit for 5 seconds when pushing Til T preferences and operating style any key except PTT L TG T UN e AU2 Lit for 5 seconds every time the The display illustration is for the Simple type and 10 key type display changes the contents transceivers OFF Does not light lt for the Non display type transceivers gt For settings of the microphone gain the squelch level the P aaa P i ON Beeps soun a oe Beep function and the Ringer level see lt OFF No beeps sound f om 5 rint BEEP UN lt for the Simple type and 10 key type transceivers gt When User Set Mode is assigned to your transceiver see page 9 for entering the User Set mode Beep Level 1 minimum 5 maximum e 1 minimum 5 maximum 3 PULL Linked with the audio level E7 The beep audio level is adjustable by JEP j rotating VOL Ringer Level e 1 minimum 5 maximum e 1 minimum 5 maximum E am Linked with the audio level ThII The ringer audio level is adjustable by RI NOY rotating VOL 14 2 BASIC OPERATION SQL Squelch Level Signal Moni 0 SQL Open Tal ATH ON Signaling beeps sound Y l T 2 SQL Threshold LAM OFF No signaling beeps
5. E Emergency Call oooooooWoWoWooo WWW 12 E Lone Worker Emergency Call 13 E Man Down Emergency CAI 13 E Motion Detection Emergency Call 13 E User Set MOde oooocoo Wo Woman 14 E Setting the Beep function oooooWooWooo 16 E Setting the Beep level Wo 17 E Setting the Ringer level o oooooWoWoWoWoom 18 E Setting the microphone gain 19 E Setting the squelch level ooooo Woo 19 3 MDC 1200 SYSTEM OPERATION E MDC 1200 system operation E Receiving a call E Transmitting a call O 1 PANEL DESCRIPTION E Front top and side panels There are three types of transceivers in the IC F1000 and ROTARY IC F2000 series SELECTOR ars IC F1000 F2000 Non display type i EOR R wi IC F1000S F2000S Simple type display 4 keys PO P3 3 CONTROL VOL IC F1000T F2000T 10 key type display 4 keys 10 key pad LED Di Emer INDICATOR The illustration is for the 10 key type Speaker Your transceiver may have a FUNCTION DISPLAY P0 ptt O SPEAKER P3 or 10 KEY PAD depending on the transceiver version SWITCH MICROPHONE PTT JACK Microphone 1 ROTARY SELECTOR uP Rotate to select the preset memory channels Upper FUNCTION DISPLAY VOLUME CONTROL VOL DOwNy Ss R
6. IPTION e Receiving Lo E o e Low Battery 2 You must charge the battery GI e Low Battery 1 You should charge the battery e When turning ON the power Calling o o o o fol o e Audible e Lockout TX Inh TOT when transmit is inhibited e Successful Oo c f e Failed Error Emergency Siren cJo R _ clo R co fefofal f ol 1 PANEL DESCRIPTION E Programmable function keys For the Non display type transceivers the following functions can be assigned to Emer Upper and Lower For the Simple type transceivers and the 10 key type trans ceivers the following functions can be assigned to PO P1 P2 P3 Emer Up and Down Consult your Icom dealer or system operator for details con cerning your transceiver s programming CH UP DOWN As described in the following topics after pushing a pro grammed key push CH Up or CH Down to select an option setting and so on ZONE only for the Simple type and 10 key type transceivers Push this key then select the desired zone by pushing CH Up or CH Down 7 What is a zone Certain channels are grouped to 4 gether and assigned to a zone according to their intend G ed use For example Staff A and Staff B are assigned Z to a Business zone and John and Cindy are assigned Z to a Private zone SCAN START STOP lt for the Non display type transceivers gt
7. N 1 TX CODE CH SELECT only for the Simple type and 10 key type transceivers Push TX Code CH Select to enter the TX code channel selection mode 1 Push CH Up or CH Down to select a desired TX code channel 2 After selecting push TX Code CH Select to store the setting and return to the standby mode only for the PMR model During TX code selection mode hold down to enter the TX code edit mode 5 Tone 1 Push CH Up or CH Down to select the desired digit You can also enter the digit using the 10 key pad if it is on your transceiver 2 Push TX Code Enter to set The digit to the right will automatically blink 3 Repeat step 1 and step 2 to input all editable digits 4 After editing push TX Code Enter to store the set tings and return to the standby mode TX CODE CH UP DN only for the LMR model for the Simple type and 10 key type transceivers Push to select a preprogrammed TX code channel i Oo 1 PANEL DESCRIPTION TX CODE CH UP DOWN only for the PMR model for the Simple type and 10 key type transceivers Push to select a preprogrammed TX code channel Push to select a desired digit in the TX code edit mode ID MR SELECT only for the PMR model for the Simple type and 10 key type transceivers Push to recall the received ID code e The transceiver can memorize up to 5 codes w Select a desired code by pushing CH Up or CH Down Hold down t
8. Tcom MDC 1200 OPERATING GUIDE VHF TRANSCEIVERS l C FIOOO Series UHF TRANSCEIVERS Ic F2000 Series am Icom Inc 3 The photo shows com INC the UHF transceivers ANon displaytype ASimpletype A 10 key type IMPORTANT We appreciate you choosing Icom for your communication needs The MDC 1200 signaling system is built into your IC F1000 IC F2000 series transceiver Icom Icom Inc and the Icom logo are registered trademarks of Icom Incor porated Japan in Japan the United States the United Kingdom Germany France Spain Russia and or other countries All other products or brands are registered trademarks or trademarks of their respective holders READ ALL INSTRUCTIONS carefully and completely before using the transceiver SAVE THIS OPERATING GUIDE This operating guide contains important operating instructions for e IC F1000 IC F1000S and IC F1000T VHF TRANSCEIVERS e IC F2000 IC F2000S and IC F2000T UHF TRANSCEIVERS TABLE OF CONTENTS IMPORTANT 4 4c08 eshte ann Mn Bn aan an i TABLE OF CONTENT Sorotna a riep ea ii 1 PANEL DESCRIPTION oma 1 9 E Front top and side panelS ooooo oo 1 E Function display esa 3 E LED indicator hana ii Ae ih aa 4 E Programmable function Keys 5 2 BASIC OPERATION o ooo oom aan 10 19 E Selecting a channel oooooWoWoWoWoWoWoWoo 10 E Receiving and tranSMitting oooooo 10
9. after pushing Upper or Lower An error beep sounds if you try to exceed the adjustable range Rotate VOL to turn OFF the power to exit the microphone gain adjustment mode D NOTE This operation may not be selectable depending on the presetting Ask your dealer for details NN E Setting the squelch level These instructions are for the non display type transceivers The sguelch circuit mutes the received audio signal de pending on the signal strength WRotate VOL to turn the transceiver power OFF Set ROTARY SELECTOR to any channel other than Channel 16 While holding down Upper rotate VOL to turn ON the power and enter the squelch level adjustment mode Push Upper to increase the squelch level tight squelch or push Lower to decrease the squelch level loose squelch e The adjustable range is 0 loose squelch to 9 tight squelch A beep sounds after pushing Upper or Lower An error beep sounds if you try to exceed the adjustable range Rotate VOL to turn OFF the power to exit the squelch level adjustment mode Z NOTE Z This operation may not be selectable depending on the 4 presetting Ask your dealer for details MDC 1200 SYSTEM OPERATION E MDC 1200 system operation The MDC 1200 signaling system enhances your transceiver s capabilities You can receive or transmit PTT ID and Emer gency calls You can also receive Radio Check Stun and Revive calls An additional feature
10. al is transmitted once or repeatedly on the emergency channel When no emergency channel is speci fied the signal is transmitted on the operating channel When the Repeat Cancel function is ON the transceiver cancels repeating after receiving an acknowledgement When the Repeat Cancel function is OFF the transceiver repeats calling according to the number of repeat cycles even after receiv ing an acknowledgement If you want to cancel the emergency call hold down the key again before transmitting the call You can transmit an emergency call without a beep emis sion and the display indication depending on the preset ting Silent operation The transceiver can also be programmed to keep the micro phone open during an emergency call allowing monitoring the situation Ask your dealer for details ZIMPORTANT It is recommended to set an emergency Z channel individually to provide the certain emergency call 4 Operation 22 Count on us Icom Inc en 1 1 32 Kamiminami Hirano ku Osaka 547 0003 Japan
11. e lowest linked level 1 Linked to the highest 5 Linked Repeatedly pushing Upper or Lower repeats the cycle See the illustration on the right The adjustable range is 1 to 5 or 1 Linked to 5 Linked e A beep sounds after pushing Upper Therefore you can determine the current level setting by the increasing loudness of the beep that sounds To determine if you have selected a linked level set VOL to minimum then push Upper up to 10 times listening for the loudest beep level 5 Pushing Upper once after the loudest beep will select 1 Linked Repeatedly push Upper or Lower to select the desired linked level Rotate VOL to turn OFF the power to exit the Ringer level adjustment mode BASIC OPERATION 2 NN Z NOTE ZY This operation may not be selectable depending on the 4 Z presetting Ask your dealer for details NN Pushing Pushing Upper Lower Upper Te Lower 2 BASIC OPERATION E Setting the microphone gain These instructions are for the non display type transceivers Adjust the microphone gain Rotate VOL to turn the transceiver power OFF Set ROTARY SELECTOR to Channel 16 While holding down Upper rotate VOL to turn ON the power and enter the microphone gain adjustment mode Push Upper or to increase or push Lower to decrease the microphone gain The adjustable range is 1 minimum to 4 maximum A beep sounds
12. ency for the set time period the transceiver transmits an emergency signal once or repeat edly on the specified emergency channel The transceiver automatically transmits a repeat emergen cy signal until it receives an acknowledgement signal or you turn OFF the transceiver power When no emergency channel is specified it transmits the signal on the previously selected channel If you want to cancel the emergency call hold down Emer gency again before transmitting the call If your transceiver is programmed for Silent operation you can transmit an Emergency call without the beep sounding and the LED indicator lighting ZY IMPORTANT It is recommended to set an emergency 4 channel individually to provide the certain emergency call Z operation BASIC OPERATION 2 X 4 NOTE Depending on the presetting the following functions are 4 automatically activated Ask your dealer for details WY e Auto TX function After an emergency call transmission the transceiver trans mits the audio from the microphone for a set time period e Auto RX function After the emergency call transmission the transceiver stands by in the audible mode for the set time period Depending on the presetting Ask your dealer for details 2 BASIC OPERATION E Lone Worker Emergency Call When the Lone Worker function is ON and if no operation occurs for a set time period the transceiver automatical ly enters the emergenc
13. ically transmits an acknowledgement to the calling station Turn power OFF or change the channel to stop the beep and the display indication 21 Receiving a Stun or Revive Call If a Stun call is received that matches your station ID the transceiver will display a stun text and you can not receive or transmit If a Revive call that matches your station ID is re ceived or you enter the password the transceiver will be revived e When the transceiver is stunned The Stun text depends on the presetting CL ICICI When you want to revive the stunned transceiver by entering a password read the following instructions Turn OFF the stunned transceiver once and then turn it ON again The illustration above is still displayed Enter the required password When you enter a correct password the transceiver will be revived and the screen will return to normal Depending on the presetting Ask your dealer for details E Transmitting a call Transmitting a PTT ID You can notify another person of your station ID or alias Push PTT to make a call Beeps sound depending on the presetting Your alias or station ID will be transmitted when you push PTT at the beginning of transmission or release it at the end of transmission depending on the presetting MDC 1200 SYSTEM OPERATION 3 Transmitting an Emergency Call When holding down Emergency for a set time period the emergency sign
14. irst selects 1 lowest to 5 highest and then selects the lowest linked level 1 Linked to the highest 5 Linked Repeatedly pushing Upper repeats the cycle See the illustration on the right The adjustable range is 1 to 5 or 1 Linked to 5 Linked 5 A beep sounds every time you push Upper Therefore you can determine the current level setting by the increasing loud Ci ness of the beep that sounds Cai To determine if you have selected a linked level set VOL to Upper 5 5 Linked minimum then push Upper repeatedly listening for the loud A est beep level 5 Pushing Upper once after the loudest beep Lower e will select 1 Linked Repeatedly push Upper to select the A desired linked level Rotate VOL to turn OFF the power to exit the Beep level 4 adjustment mode 1 Linked A E Setting the Ringer level These instructions are for the non display type transceivers The Ringer level can be adjusted between 1 and 5 or 1 Linked and 5 Linked When a Linked option is selected the ringer audio level is adjustable by rotating VOL Rotate VOL to turn OFF the transceiver power 2 Set ROTARY SELECTOR to Channel 16 While holding down Lower rotate VOL to turn ON the power and enter the Ringer level adjustment mode Push Upper to increase or push Lower to decrease the Ringer level e Repeatedly pushing Upper first selects 1 lowest to 5 highest and then selects th
15. iver returns to the Normal mode then SHIFT OFF is briefly displayed e The Shift mode enables a programmable function key to have two functions at the same time E Selecting a channel There are several types of channel selections Methods may differ depending on the presetting Consult your dealer for details NON ZONE TYPE To select the desired operating channel Rotate ROTARY SELECTOR Push CH Up or CH Down Push one of MR CH 1 to MR CH 4 Push Prio AJ Prio BJ Prio A Rewrite or Prio B Re write ZONE TYPE To select the desired operating channel Push Zone then push CH Up or CH Down AUTOMATIC SCAN TYPE Channel setting is not necessary for this scan type When turning ON the power the transceiver automatically starts scanning Scanning stops when a signal is received BASIC OPERATION 2 E Receiving and transmitting 7 CAUTION ZY Attach an antenna before transmitting D Transmitting without an antenna may damage the trans 4 ceiver Receiving Rotate VOL to turn ON the power Rotate ROTARY SELECTOR or push one of the memo ry channel keys MR CH1 to MR CH4 to select a chan nel When receiving a call adjust the audio output level to a comfortable listening level Transmitting Wait until the channel is clear to avoid interference While holding down PTT speak at a normal voice level Release PTT to receive Z IMPORTANT To maxi
16. mize the readability of your signal 1 After pushing PTT pause briefly before you start speaking 2 Hold the microphone 5 to 10 cm 2 to 4 inches from your mouth then speak at a normal voice level NN 2 BASIC OPERATION Transmitting notes e Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions The channel is busy However depending on the presettings you can transmit when the call includes an unmatched or matched CTC SS DTCS tone The selected channel is a receive only channel e Time out timer If continuous transmission exceeds the preprogrammed time out timer limit transmission is cut off e Penalty timer The time out timer cuts off transmission further transmis sion is inhibited for the preprogrammed penalty timer peri od Receiving a Stun Kill and Revive call The dispatcher can send a 2 Tone or 5 Tone that will stun kill or revive your transceiver When the Stun call is received beeps sound and you can not receive or transmit Receiving a Revive call or entering a password is necessary to operate the transceiver again When the Kill call is received beeps sound and the trans ceiver becomes unusable Cloning the transceiver is neces sary to operate the transceiver again in this case Depending on the presetting Ask your dealer for details E Emergency Call When pushing Emerg
17. o clear the selected ID code SCRAMBLER lt for the Non display type transceivers gt Hold down to turn ON the Voice Scrambler function Push to turn OFF the function lt for the Simple type and 10 key type transceivers gt Push to turn the Voice Scrambler function ON or OFF COMPANDER lt for the Non display type transceivers gt Hold down to turn ON the Compander function Push to turn OFF the function lt for the Simple type and 10 key type transceivers gt Push to turn the Compander function ON or OFF The Compander function reduces noise components from the transmitted audio to provide clear communication USER SET MODE only for the Simple type and 10 key type transceivers Hold down to enter the User Set mode e While in the User Set mode push this key to select an item and change the value or setting by pushing CH Up or CH Down Selectable items may differ depending on the presetting Hold down this key again to exit the User Set mode ANNOUNCE Push to turn the Channel Announce function ON or OFF Y NOTE 4 When the Beep function p 16 is OFF the operating chan 4 nel is not announced regardless of this setting SHIFT only for the Simple type and 10 key type transceivers 1 Push to turn ON the Shift mode key functions SHIFT ON is briefly displayed 2 Push another key to activate its secondary function 3 Push Shift again to turn OFF the function The transce
18. of the MDC 1200 system included in Icom transceivers is called aliasing Each transceiver on the system has a unique ID number Aliasing is a substitute for this ID number and you can give an alphanumeric name for each station ID In transmit you can use this alias to select a transceiver to call In receive the alias of the calling station is displayed instead of the ID Please confirm that your dealer has set one of the program mable keys for MDC 1200 system operation See page 5 for more information about the programmable function keys The display illustration is for the Simple type and 10 key type transceivers E Receiving a call Receiving a PTT ID When a PTT ID is received e Beeps sound e The calling station ID or alias is displayed lt Calling station ID gt Til T TT IZILI tu CIA Til am VTE Co Aiur ri Hold down PTT and speak into the microphone Release PTT to receive a response 3 3 MDC 1200 SYSTEM OPERATION Receiving an Emergency Call When an emergency call is received e Beeps sound e The calling station ID or alias and EMG EMG are al ternately displayed e The operation of the backlight depends on the Back light setting in the User set mode When LIGHT AUT or LIGHT AU2 is selected the backlight turns ON for a set time period Yal CHEE T L When the Send Ack function is turned ON the transceiver automat
19. otate to turn the power ON or OFF and to adjust the Lower P0 P1 audio level P2 P3 DEALER ASSIGNABLE KEY Emer 10 KEY PAD A desired function can be programmed by your dealer Names for the non display type transceiver O SPEAKER MICROPHONE JACK Connect optional equipment Y NOTE After turning OFF the transceiver connect or dis Y connect the optional equipment Jack cover NOTE Attach the jack cover when optional equipment is not used FUNCTION DISPLAY Displays a variety of information such as the operating channel number channel name User Set mode con tents and so on See page 3 for details Q DEALER ASSIGNABLE KEYS P0 P3 Desired functions can be independently programmed by your dealer DEALER ASSIGNABLE KEYS UP or Upper DOWN or Lower Desired functions can be independently programmed by your dealer Names for the non display type transceivers PTT SWITCH PTT Hold down to transmit release to receive PANEL DESCRIPTION 1 LED INDICATOR Lights red while transmitting Lights green while receiving a signal or when the squelch is open Lights or blinks orange when the matched 2 Tone or 5 Tone is received depending on the presetting You should charge the battery when the indicator slow ly blinks You must charge the battery when the indicator blinks fast ANTENNA CONNECTOR Connects the supplied antenna
20. r SW ON timer period to turn ON the Emergency function After the Start or Repeat timer period ends an Emer gency call is automatically transmitted once or repeat edly depending on the presetting Hold down during the Emer SW OFF timer period to can cel the Emergency function before transmitting an Emer gency call SURVEILLANCE lt for the Non display type transceivers gt Hold down to turn ON the Surveillance function Push to turn OFF the function lt for the Simple type and 10 key type transceivers gt Push to turn the Surveillance function ON or OFF e When this function is ON and a signal is received a beep does not sound and the LED does not light even if you push any key SIREN Hold down to emit a siren sound e This function may use for situations other than an emer gency alert such as a security alarm Turning OFF the transceiver power to stop the siren sound TX CODE ENTER only for the PMR model for the Simple type and 10 key type transceivers Push to enter the TX code edit mode 5 Tone 1 Push CH Up or CH Down to select the desired digit You can also enter the digit using the 10 key pad if it is on your transceiver 2 Push TX Code Enter to set The digit to the right will automatically blink Repeat step 1 and step 2 to input all editable digits 4 After editing push TX Code Enter to store the setting and return to the standby mode w PANEL DESCRIPTIO
21. sound Mn And e 9 SQL Tight JUL g MILOM UIN AF Min Level Lone Worker Minimum audio output level ON If no operation occurs for a set Y l T 0 minimum 255 maximum time period the transceiver au MIMI FINE tomatically enters the Emergen LOIN OIN Mic Gain more sensitive to the user s voice Higher values make the microphone je NM e 1 minimum 4 maximum Hl 4 ra cy mode OFF Even if no operation occurs for a set time period the trans ceiver does not automatically enter the Emergency Battery Voltage Display turning ON the transceiver e ON Battery voltage is displayed when yul OFF Battery voltage is not displayed an BATT ON when turning ON the transceiver mode Stationary Higher values make the acceleration sen Yul TE sor more sensitive to the user s motion TTM V 1 minimum 3 maximum J NHR Motion Detection Higher values make the acceleration sen Yul T sor more sensitive to the user s motion e 1 minimum 3 maximum E Setting the Beep function These instructions are for the non display type transceivers The Beep function can be turned ON or OFF When it is OFF the channel announcement is also turned OFF NOTE 4 You should turn ON the Beep function when you set the D Beep level the Ringer level the microphone gain and the 4 squelch le
22. tly select memory channel 1 2 3 or 4 if pro grammed MONI only for the LMR mode Hold down to cancel the CTCSS DTCS or 2 Tone mute The transceiver enters Audible mode Push to turn OFF the function MONI Audi only for the PMR mode Hold down to cancel the CTCSS DTCS or 5 Tone mute The transceiver enters Audible mode Push or hold down to activate one or two functions if pro grammed PANEL DESCRIPTION 1 LOCK lt for the Non display type transceivers gt Hold down this key to lock all programmable keys except the followings Moni Lock Emer Surveillance Siren Lone Worker and Shift lt for the Simple type and 10 key type transceivers gt Hold down until LOCK ON is displayed to lock all pro grammable keys except the followings Moni Lock Emer Surveillance Siren Lone Worker and Shift To turn OFF the Key Lock function hold down until LOCK OFF is displayed LONE WORKER lt for the Non display type transceivers gt Hold down to turn ON the Lone Worker Function Push to turn OFF the Function lt for the Simple type and 10 key type transceivers gt Push to turn the Lone Worker Function ON or OFF e If no operation occurs for a set time period the trans ceiver automatically enters the emergency mode HIGH LOW Push to select the transmit output power temporarily or permanently depending on the presetting
23. vel Rotate VOL to turn the transceiver power OFF Set ROTARY SELECTOR to any channel other than Channel 16 While holding down Lower rotate VOL to turn ON the power to enter the Beep level adjustment mode Push Lower to turn the Beep function ON or OFF When a beep sounds after pushing Lower the Beep function is ON When no beep sounds after pushing Lower the Beep function is OFF The transceiver stores the setting every time you change it If desired push Upper to adjust the Beep level See page 17 for details Rotate VOL to turn OFF the power to exit the Beep level adjustment mode BASIC OPERATION 2 ROTARY SELECTOR Upper Lower 79 2 BASIC OPERATION E Setting the Beep level These instructions are for the non display type transceivers Y NOTE The Beep level is adjustable between 1 and 5 or 1 linked and Z This operation may not be selectable depending on the 5 linked When a Linked option is selected the beep audio 4 presetting Ask your dealer for details level is adjustable by rotating VOL WRotate VOL to turn OFF the transceiver Set ROTARY SELECTOR to any channel other than Channel 16 ROTARY SELECTOR peal While holding down Lower rotate VOL to turn ON the pekan 4 power and enter the Beep level adjustment mode 1 Push Upper to change the Beep level VOL e Repeatedly pushing Upper f
24. y mode Then the countdown for the emergency call transmission starts After a set time period has passed an emergency call is au tomatically transmitted once or repeatedly If the user operates the transceiver before the call is trans mitted the transceiver exits the emergency mode and the emergency call is cancelled To turn ON the function see page 6 E Man Down Emergency Call This function may or may not be available depending on the presetting When the transceiver has been left in a horizontal position for a set time period the transceiver enters the emergency mode and then a countdown starts After a set time period has passed an emergency call is au tomatically transmitted once or repeatedly If the transceiver is placed in a vertical position before the first transmission the transceiver exits the emergency mode and the emergency call is cancelled E Motion Detection Emergency Call This function may or may not be available depending on the presetting If the acceleration sensor detects the user continuous ly moves for the set timer period and at the set speed the transceiver enters the emergency mode and then the count down starts After a set time period has passed an emergency call is au tomatically transmitted once or repeatedly Once the countdown starts you cannot cancel the emergen cy call Depending on the presetting Ask your dealer for details BASIC OPERATION 2
Download Pdf Manuals
Related Search