EVLCDx Z-Wave Specification Rev H
Contents
1. EVLCD Z Wave Specification Rev G Ev lve Appendix Keypad Types What it Says What it Does All On e Turns ON Activates all lights in Guest Room e Opens Guest Room Drapes amp Sheers e Activates HVAC to Occupied All Off e Turns OFF all Guest Room Lights e Closes Guest Room Drapes amp Sheers e Sets HVAC to Un Occupied Mood e Sets ALL Room lights to 40 Do Not Disturb e Activates DND Indicator on Doorbell Station e Activates DND Indicator on All Keypads e Disables Doorbell Button e Disables House Keeping Indication on System House Keeping e Activates House Keeping Indicator on Doorbell Station e Activates House Keeping Indicator on All Keypads e Disables DND Indication on System What it Says What it Does GUESTROOMWALL All On e Turns ON Activates all lights in Guest Room All Off e Turns OFF all Bedroom Lights e Does not affect Bathroom Lights Mood e Sets ALL Bedroom lights to 40 Lamps e Turns ON Bedroom Lamps Night Lite e Turns ON Bathroom Night Light e Turns OFF all Guest Room Lights What it Says What it Does GUESTROOMTABLE All On e Turns ON Activates all Guest Room Lights TOP All Off e Turns OFF all Lights in the Entire Guest Room e Turns OFF Bathroom Lights Mood e Turns ON all Bedroom Lights to 40 Lamps e Turns ON Bedroom Lamps Night Lite e Turns ON Bathroom Night Light e Turns OFF all other Guest Room Lights Do Not Disturb2. Momentary Press Opens Living Room Drapes Fully e Press and Hold Opens Drapes Stops on Button Release Drapes Closed e Momentary Press Closes Living Room Drapes Fully e Press and Hold Closes Drapes Stops on Button Release Stop e Stops Drapes or Sheers Travel Open or Closed Sheers Open e Momentary Press Opens Living Room Sheers Fully e Press and Hold Opens Sheers Stops on Button Release Sheers Closed e Momentary Press Closes Living Room Sheers Fully e Press and Hold Closes Sheers Stops on Button Release EVLCD Z Wave Specification Rev G 16 BEDROOM 1GANG BEDROOM 1GANGTABLE BEDROOM SGANGTABLE EVLCD Z Wave Specification Rev G What it Says What it Does All On e Turns ON Activates all lights in Bedroom e Opens Bedroom Drapes amp Sheers All Off e Turns OFF all Bedroom Lights e Turns OFF all Bathroom Lights e Closes ALL Bedroom Drapes amp Sheers Mood e Sets ALL Bedroom lights to 40 e Turns OFF all non dimmables in Bedroom Lamps e Turns ON Bedroom Lamps e Turns OFF other Bedroom Lights Night Lite e Turns ON Bathroom Night Light e Turns OFF all Bedroom Lights What it Says What it Does All On e Turns ON Activates all Bedroom Lights Up Arrow e Raises Heating Cooling Set Point on Bedroom HVAC a e Middle Button Not Used Down Arrow e Lowers Heating Cooling Set Point on Bedroom HVAC All Off e Turns OFF all Lights in the Bedro
3. e Activates DND Indicator on Doorbell Station e Activates DND Indicator on All Keypads e Disables Doorbell Button e Disables House Keeping Indication on System Up Arrow e Raises Heating Cooling Set Point e Middle Button Not Used Down Arrow e Lowers Heating Cooling Set Point House Keeping e Activates House Keeping Indicator on Doorbell Station e Activates House Keeping Indicator on All Keypads e Disables DND Indication on System Drapes Open e Momentary Press Opens Bedroom Drapes Fully e Press and Hold Opens Drapes Stops on Button Release Drapes Closed e Momentary Press Closes Bedroom Drapes Fully e Press and Hold Closes Drapes Stops on Button Release Stop e Stops Drapes or Sheers Travel Open or Closed Sheers Open e Momentary Press Opens Bedroom Sheers Fully e Press and Hold Opens Sheers Stops on Button Release Sheers Closed e Momentary Press Closes Bedroom Sheers Fully e Press and Hold Closes Sheers Stops on Button Release What it Says What it Does EVLCD Z Wave Specification Rev G 14 All On Turns ON all Living Room Lights LIVINGROOM All Off Turns OFF all Living Room Lights LEFT Mood Sets Living Room lights to 40 Turns OFF all non dimmables Ceiling Turns ON all Living Room Ceiling Lights Turns OFF Perimeter Lights Ignores Lamps Perimeter Turns ON all Living Room Perimeter Art Lights Turns OFF Ceiling Lights Ignores Lamps What i
4. ASS SCENE ACTIVATION COMMAND CLASS SCENE CONTROLLER CONF COMMAND CLASS VERSION COMMAND_CLASS_SCREEN_ATTRIBUTES COMMAND_CLASS_SCREEN_MD COMMAND_CLASS_POWERLEVEL COMMAND CLASS BASIC not supported COMMAND CLASS ASSOCIATION The EVLCDx supports 16 groups and 30 associations in each group The groups are broken down as follows EVLCD3 Groups 1 15 corresponds to keypad button scenes 1 15 Group 16 All the keypads in the system used for setting Language options DND HK to all keypads EVLCD1 EVLCD2 Groups 1 5 corresponds to keypad button scenes for buttons 1 5 Groups 6 10 corresponds to the Off button scenes for buttons 1 5 Group 16 All the keypads in the system used for setting Language options DND HK to all keypads OR if Keypad Type CUSTOM METADATA this will be the Indicator Group EVLCD Z Wave Specification Rev G 5 Ev lve COMMAND_CLASS_CONFIGURATION There are configuration parameters accessible via the COMMAND CLASS CONFIGURATION Configuration Parameter 1 Description Button 1 Type Button 2 Type Button 3 Type Button 4 Type Button 5 Type Button 6 Type Button 7 Type Button 8 Type Button 9 Type Button 10 Type Button 11 Type Button 12 Type Button 13 Type Button 14 Type Button 15 Type Language EVLCD Z Wave Specification Rev G Length bytes 1 ae mk mk mk mk mk mk mk R W capability R W R W R W R W R W S 9 2 0 0 land kand k
5. COMMAND CLASS ASSOCIATION 2 ies esse sere BEE GEN G Ee sdatens KEER KNEG care VEE ee Ee GES ES KEES DNE RS Gee aka daaa iEn 5 COMMAND_CLASS_CONFIGURATION ese ese ee ee se ek ee ee AA Ge Ke Ge AA AR iaaa aa adian AA Ge AA de ee ee 6 COMMAND CLASS MANUFACTURER SPECIFIC ese dees ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ke ee ee de ee ee ee eek 9 COMMAND CLASS SCENE ACTIVATION ees ee ee se ee ee ee ee ee ee ee ee ee ee ee ee ke ee ee ee ee ee ee ee ee ee de ee ee ee ee ee ee 10 COMMAND CLASS SCENE CONTROLLER CONFIG iese dese ee ee ee ee ee ee ee ee ee se ee ee ee ee de ee ee ee ee ee ee 10 COMMAND CLASS VERSION ees ee ee ee ee ee ee Ge AA Ge AR Ge AA Ge ee ee ee Re ee Ge ee aaeeei ee ee ee ee 10 COMMAND CLASS THERMOSTAT SETPOINT eise sesse dese ee ee se ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee de ee ee ee ee ee ee 10 COMMAND CLASS MULTILEVEL SENSOR esse ee ese ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee de ee ee de ee ee ee 11 COMMAND CLASS SCREEN ATTRIBUTES Version 1 iese ee se se ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee de ee ee ee ee ee ee 12 COMMAND CLASS SCREEN META DATA Version 1 iese esse ee se ee ee se ee ee ee ee ee ee ee se ee ee ee ee de ee ee ee ee ee ee 12 COMMAND CLASS POWER LEVEL ese ee ee se ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ke ee ee de ee ee ee ee ee ee de ee ee de ee ee ee 13 Koypad TYPES RE EE AE EE ER EE N 14 EVLCD Z Wave Specification R
6. Ev lve LCD Keypad Z Wave Specification Product EVLCD Baseline FW Z Wave 4 5 2 EVLCD core 0 0 31 History Date Description 6 17 11 Changed MFG ID to use Evolves Clarified METADATA Double Line character CR 5 19 11 Updated COMMAND_CLASS_SCREEN_ATTRIBUTES reference from CUSTOM METADATA 14 to CUSTOM METADATA 17 Corrected Config Parameter 16 supported language list Added verbiage for Z Wave networks Changed Default Screen Type to Custom Metadata 17 Added Custom Button type 6 Scene On BasicSet OFF 4 5 11 Added Factory Reset section 3 8 11 Changed to 4 5 2 release 1 13 10 New EVLCD1 Product ID L2 for Metadata capable LCD1 Added METADATA CC Added RGB support and Config registers 12 1 10 General Updates Addition of extra LCD1 screens 6 25 10 Removed Group 17 Clarified Group 16 use Added Keypad Type definitions 6 1 09 First Draft sleg AR RR N 1 FUNCTION Al QVORVICW EE EE EE EE DE ED EE 2 Z Wave NetWOTK SR AE N N RO RE N N Or 2 Language Selection SCr e M eisian iae aaa EA aa E a AAA Naa 2 installer Screen encisar EE EE EE N 2 Facto ROSET resesi ER EE EE 2 DND Privacy and Housekeeping iss esse esse ee ee es se ee ee ese ee ee ee ee ee Re RREA NENES ee ee ee ee Re ee ee ee ee 3 AE GN RENE OR RE N N 3 sed Isie ER As EE RE EE N RE N NE EE N 5 Telrele de ie AE N RE N E 5 GOMMAND CLASS BASIE EES seen ENE ee Gene E GEN ite Ge eg EE GED ent ee ee EE KEES Ee eaten RE ERNS RS a AER GENE ee ge og 5
7. M1GANG 8 SBEDROOM1GANGTABLE 9 SBEDROOM38GANGTABLE 10 DRAPECONTROL1GANG 11 VANITYBATH1GANG 12 SONOSTA1GANG 13 INATPENN1GANG 14 TYPE14 15 LOWELL1 16 LOWELL2 17 CUSTOM METADATA 18 CES3DEMO see appendix for Keypad types 18 reserved 1 R W 0 19 reserved 1 R 20 Display Timeout 1 RAN 15 Seconds 21 Backlight ON 1 R W 15 Range 1 20 Level 22 Backlight OFF 1 R W 0 Range 1 20 Level 23 Button ON Level 1 R W 15 Range 1 20 24 Button OFF 1 R W 0 Range 1 20 Level 25 LCD Contrast 1 R W 14 Range 5 20 26 Screen 1 R W 0 0 Normal 1 Rotated 180 Orientation 27 Network Update 1 R W 0 Range 0 60 seconds When loaded LCD will trigger a Network Update after timeout 28 Reserved 29 Red Backlight 1 R W 100 0 100 ON Level 30 Blue Backlight 1 R W 100 0 100 ON Level 31 Green Backlight 1 R W 100 0 100 ON Level 32 RGB Demo 1 R W 0 O off 1 on Mode Scrolls through RGB levels Only 1 button can be defined as a Privacy Button Only 1 button can be defined as a Housekeeping Button EVLCD Z Wave Specification Rev G 7 TM Ev lve Sends Scene command to association group when un inverted sends BASIC_SET OFF to association group when inverted EVLCD Z Wave Specification Rev G 8 TM Ev lve COMMAND_CLASS_ INDICATOR It is used to indicate the state of each of the 5 pushbuttons If the screen area associated with the button is not inverted the bit value will be 0 If the screen area is inverted or highlighted the bit va
8. OMMAND_CLASS_THERMOSTAT_SETPOINT The EVLCD accepts setpoint reports from thermostats and will use the value for the thermostat function of the EVLCD Note Thermostats must be associated with the EVLCD s for the setpoint information to be sent to the EVLCD SET level SETPOINT HEATING1 Setpoint number level2 FC_FAHRENHEIT 1 byte format valuel setpoint value EVLCD Z Wave Specification Rev G 10 TM Ev lve GET N A REPORT Thermostat setpoint value COMMAND_CLASS_MULTILEVEL_SENSOR The EVLCD accepts MultiLevel Sensor temperature reports from thermostats and will use the value for the thermostat function of the EVLCD Note Thermostats must be associated with the EVLCD s for the temperature information to be sent to the EVLCD SET N A GET N A REPORT Thermostat temperature value EVLCD Z Wave Specification Rev G 11 Ev lve COMMAND_CLASS_SCREEN_ATTRIBUTES Version 1 The Screen Attributes command is used to retrieve the screen attributes from the EVLCD1 SET N A GET EVLCD will send a GET upon powerup if the keypad type configuration parameter is CUSTOM METADATA 17 REPORT 7 6 5 4 3 2 1 0 COMMAND_CLASS_SCREEN_ATTRIBUTES SCREEN ATTRIBUTES REPORT Reserved Number of Lines 000 00101 5 Number of Chars per line 16 Size of line Buffer 16 Numerical Presentation 00000001 XXXXXXX 1 Supports Ascii codes XXXXXX 1X Suppo
9. VANITYBATH What it Says Shower Nightlight All On All Off SONOSTA What it Says Entry IGANG Sconce Bed Left Bed Right GoodNight What it Says INATPENN vanity y 1GANG Shower Nightlight All On All Off What it Says TYPE14 Entry LivingRoom BedRoom Master Off What it Says LOWELL1 Welcome 1GANG Overhead Bedroom Privacy All Off LOWELL2 What it Says 1GANG Lights Up Arrow Temperature Down Arrow Privacy Activates DND Indicator on Doorbell Station Activates DND Indicator on All Keypads Disables Doorbell Button Disables House Keeping Indication on System EVLCD Z Wave Specification Rev G 18 lve CES3 DEMO What it Says What it Does 1GANG Morning Sends Scene Activate to nodes in Group 1 Day Sends Scene Activate to nodes in Group 2 Evening Sends Scene Activate to nodes in Group 3 Night Sends Scene Activate to nodes in Group 4 Sleep Sends Scene Activate to nodes in Group 5 EVLCD Z Wave Specification Rev G 19
10. and and land ian D Default Value 0 AO OIOIOIOIOOOIOO Notes 0x00 Scene Control momentary 0x01 Scene Control toggle 0x02 BASICSET Toggle 0x03 n a 0x04 Privacy 0x05 HouseKeeping 0x06 Scene Control BASICSET toggle 0x00 Scene Control momentary 0x01 Scene Control toggle 0x02 BASICSET Toggle 0x03 Stat Setpoint Up 0x04 Privacy 0x05 Housekeeping 0x06 Scene Control BASICSET toggle 0x00 Scene Control momentary 0x01 Scene Control toggle 0x02 BASICSET Toggle 0x03 Stat Temperature 0x04 Privacy 0x05 HouseKeeping 0x06 Scene Control BASICSET toggle 0x00 Scene Control momentary 0x01 Scene Control toggle 0x02 BASICSET Toggle 0x03 Stat Setpoint Down 0x04 Privacy 0x05 Housekeeping 0x06 Scene Control BASICSET toggle 0x00 Scene Control momentary 0x01 Scene Control toggle 0x02 BASICSET Toggle 0x03 n a 0x04 Privacy 0x05 Housekeeping 0x06 Scene Control BASICSET toggle EVLCD3 only EVLCD3 only EVLCD3 only EVLCD3 only EVLCD3 only EVLCD3 only EVLCD3 only EVLCD3 only EVLCD3 only EVLCD3 only 1 English 2 Spanish Ev lve Configuration ER Length R W Default Notes Parameter PES adel bytes capability Value 3 Chinese 4 German 5 French 6 Italian 7 Punjabi 17 Keypad Type 1 R W 17 1 ENTRY2GANG 2 RESORTROOMWALL 3 RESORTROOMSGANGTABLE 4 SLIVINGROOMLEFT 5 SLIVINGROOMRIGHT 6 SLIVINGROOM3GANG 7 SBEDROO
11. arious manufacturers support the Z Wave process of adding or removing a device from a network The EVLCDx is a Z Wave Controller and can only act as a secondary controller and that another Z Wave controller is required as the primary controller to setup and maintain the network A Z Wave network is a collection of Z Wave modules in a mesh type of network Each Z Wave module regardless of manufacturer communicates with other modules within range to route and repeat the signals from one device to the next this creates a highly reliable and robust transmission throughout the home In addition the network becomes stronger as more modules are added The following procedure will allow the EVLCDx to be included or removed from a Z Wave network Inclusion Including the keypad into an Existing Network 1 Set your primary controller to Include mode to add the keypad as a node on your network see your controllers user manual for detailed instructions 2 If the EVLCDx Keypad is not installed as shown on the screen when the keypad first powers up Press the upper leftmost keypad button when the main screen is displayed The controller will indicate the keypad has been included into the network Your controller will indicate the keypad was successfully added to its network see your controller s user manual for details Also you can check if the keypad was successfully added to the network by checking the ZHID Home ID and ZNID Node ID
12. e keypad power EVLCD Z Wave Specification Rev G 3 TM Ev lve 3 Hold down the top keypad button 4 Apply keypad power continue to hold button until the maintenance screen appears 5 Select Z Wave ZW Install Add to Network The controller will indicate the keypad has been removed from the network Exclusion Removing the keypad from a Network 6 Set your primary controller to Remove mode to remove the keypad as a node on your network see your controllers user manual for detailed instructions 7 Remove keypad power 8 Hold down the top keypad button 9 Apply keypad power continue to hold button until the maintenance screen appears 10 Select Z Wave ZW Install Add to Network The controller will indicate the keypad has been removed from the network EVLCD Z Wave Specification Rev G 4 Evolve COMMAND CLASSES Introduction This document is for the advanced user who has knowledge of the Z WaveTM Command Classes and is able to initiate Z Wave commands programmatically When the EVLCD sends a Node Info Report it reports itself as a Static Controller device with GENERIC TYPE STATIC CONTROLLER SPECIFIC TYPE NOT USED BASIC TYPE STATIC CONTROLLER In addition to the mandatory command classes it also supports COMMAND CLASS BASIC COMMAND CLASS ASSOCIATION COMMAND CLASS CONFIGURATION COMMAND CLASS INDICATOR COMMAND CLASS MANUFACTURER SPECIFIC COMMAND CL
13. ev G 1 TM Ev lve Functional Overview The system consists of LCD Keypads Lighting devices Drape Relay controllers and Thermostats All communicating over a Z Wave network Scenes will be the primary mechanism for activating various modes in the room A provisioning tool will be used to do the initial node assignment and to then configure the various scenes using a predefined room template The LCD Keypads will act as a Scene Controller Upon the pressing of a button a Scene Activate BasicSet or other Command will be sent out to the nodes predefined in a group s association list The Keypads scenes are configured using the Scene Controller Configuration command class The Group ID will match the association group ID used when the Scene Activation Command Class is sent to the nodes in the group Z Wave Network The EVLCD keypads will be configured as a Controller in the Z Wave environment This will allow it to store more than the 5 routes a slave device does The Z Wave library will be the 4 5 2 release allowing the use of Explorer frames The Z Wave Node Info frame is used to notify a network management device If the EVLCD has not been included into a network pressing any of the buttons will cause the Node Info frame to be sent out and go into a learn mode to be included into a network If the EVLCD is part of a network removing it from a network will involve accessing the Installer screen Language Selection Scree
14. he return message will contain the following Manufacturer ID 0113 Product Type ID EV EVLCD1 Product ID L1 EVLCD1 Enhanced Product ID L2 EVLCD1 that supports METADATA EVLCD3 Product ID L3 EVLCDD2 Product ID D2 EVLCD Z Wave Specification Rev G 9 Ev lve COMMAND_CLASS_SCENE_ACTIVATION The Scene Activation is used to launch a particular scene in the Zwave ecosystem The Scene must have been previously setup in the devices using the Scene Actuator Configuration Set command The Scene Activation command is sent using a Multicast frame followed by the individual Singlecast frames SET Scene ID range is 1 255 Dimming Duration will used stored value GET N A REPORT N A COMMAND_CLASS_SCENE_CONTROLLER_CONFIG The Scene Controller Configuration Command Class is used to configure scenes in the EVLCD keypads SET EVLCD3 Group ID range is 1 15 EVLCD1 Group ID range is 1 10 1 5 ON Scene 6 10 OFF Scene Scene ID range is 1 255 0 Disabled Dimming Duration GET EVLCD3 Group ID range is 1 15 EVLCD1 Group ID range is 1 10 1 5 ON Scene 6 10 OFF Scene REPORT EVLCD3 Group ID range is 1 15 EVLCD1 Group ID range is 1 10 1 5 ON Scene 6 10 OFF Scene Scene ID range is 1 255 Dimming Duration COMMAND_CLASS_VERSION Send VERSION_GET The returned message is Application Version is the Z Wave processor code version Application Sub Version is the EVLCD processor code version C
15. located in the Z Wave Info screen The Z Wave Info screen is accessible by holding down the top keypad button while the keypad is powering up releasing when the maintenance screen appears Inclusion and exclusion are always done at normal transmit power mode If your controller supports NWI then you can optionally set the primary to NWI include mode Please note that NWI inclusion mode does not end when you have included a new node This allows multiple nodes to be included without having to physically go back to the controller to initiate the next inclusion Therefore you must manually terminate NWI inclusion mode at the controller when you have finished including any new nodes to the network Since intermediate included nodes will assist the inclusion process by routing messages we recommend that nodes close to the primary controller be installed first proceeding out in consecutive rings from the controller Note Before adding the keypad to a Z Wave Network check that it does not already belong to one by viewing the Home and Zone ID s located in the Z Wave Info screen An un configured keypad should show a Node ID of 1 and a random Home ID Consult your controller s user manual for details on removing a device from a Z Wave network Exclusion Removing the keypad from a Network 1 Set your primary controller to Remove mode to remove the keypad as a node on your network see your controllers user manual for detailed instructions 2 Remov
16. lue will be 1 Upon a change to a toggle type of button the Indicator Report command will be sent to all the nodes in Association Group 16 The least significant bit of the Value field will correspond to pushbutton 1 the next most bit pushbutton 2 and so forth If the button is defined as a Housekeeping or Privacy type of button it is used to indicate the state of the Privacy or Housekeeping status indications Upon a change in the Privacy or Housekeeping status on any of the keypads the Indicator Set command will be sent to all the keypads in Association Group 16 The least significant bit of the Value field will be the Privacy indicator the next most bit will be the Housekeeping Indicator SET An EVLCD receiving a SET command will invert un invert the screen area based on the corresponding bit value Privacy will use bit 0x01 Housekeeping will use bit 0x02 Pushbutton 1 will use bit 0x04 Pushbutton 2 will use bit 0x08 Pushbutton 3 will use bit 0x10 Pushbutton 4 will use bit 0x20 Pushbutton 5 will use bit 0x40 GET Return the INDICATOR REPORT REPORT An EVLCD will send a REPORT whenever the buttons screen area is changed Privacy will use bit 0x01 Housekeeping will use bit 0x02 Pushbutton 1 will use bit 0x04 Pushbutton 2 will use bit 0x08 Pushbutton 3 will use bit 0x10 Pushbutton 4 will use bit 0x20 Pushbutton 5 will use bit 0x40 COMMAND_CLASS_MANUFACTURER_SPECIFIC Send MANUFACTURER_SPECIFIC_GET T
17. n The Language Selection Screen is accessed by pressing and holding the top and bottom buttons left most set of buttons on the EVLCD3 Once in the Language screen pressing the top button will cycle through the various languages pressing the bottom button Done will exit The Language screen will timeout and revert back to the main screen when there is 30 seconds of no button activity When exiting from the Language screen the keypad will send a Configuration SET command to the other keypads in the network to change the Language type Installer Screen The Installer Screen is accessed by pressing and holding the 1st button while powering up the keypad The Installer Screen will display current Z Wave information including Node ID Home ID and Z Wave firmware revision Factory Reset To restore the EVLCD to Factory Default Settings 1 Navigate to the Installer Screen by pressing and holding the 1st button while powering up the keypad 2 Select Keypad 3 Select Factory 4 Press the Yes button EVLCD will restore to Factory Default Settings EVLCD Z Wave Specification Rev G 2 TM Ev lve DND Privacy and Housekeeping The DND and Housekeeping indicators will be synchronized among the keypads using the INDICATOR command class By default the indicators will both be inactive Any keypad can change the state using the SET command see COMMAND_CLASS_INDICATOR description Z Wave Installation Z Wave controllers from v
18. nds Scene Activate to nodes in Group 2 Sends Scene Activate to nodes in Group 3 Sends Scene Activate to nodes in Group 4 Sends Scene Activate to nodes in Group 5 What it Does Toggles Basic Set to nodes in Group 1 Toggles Basic Set to nodes in Group 2 Toggles Basic Set to nodes in Group 3 Toggles Basic Set to nodes in Group 4 Sends Scene Activate to nodes in Group 5 What it Does Toggles Basic Set to nodes in Group 1 Toggles Basic Set to nodes in Group 2 Toggles Basic Set to nodes in Group 3 Sends Scene Activate to nodes in Group 4 Sends Scene Activate to nodes in Group 5 What it Does Toggles Basic Set to nodes in Group 1 Toggles Basic Set to nodes in Group 2 Toggles Basic Set to nodes in Group 3 Toggles Basic Set to nodes in Group 4 Sends Scene Activate to nodes in Group 5 What it Does Sends Scene Activate to nodes in Group 1 Toggles Basic Set to nodes in Group 2 Toggles Basic Set to nodes in Group 3 Activates DND Indicator on Doorbell Station Activates DND Indicator on All Keypads Disables Doorbell Button Disables House Keeping Indication on System Sends Scene Activate to nodes in Group 5 What it Does Sends Scene Activate to nodes in Group 1 Raises Heating Cooling Set Point Middle Button Not Used Lowers Heating Cooling Set Point
19. om e Turns OFF all Lights in the Bathroom What it Says What it Does All On e Turns ON Activates all Bedroom Lights All Off e Turns OFF all Lights in the Entire Suite Mood e Turns ON all Bedroom Lights to 40 e Turns OFF all other Bedroom Lights Lamps e Turns ON Bedroom Lamps Night Lite e Turns ON Bathroom Night Light e Turns OFF all other Bedroom Lights Do Not Disturb Activates DND Indicator on Doorbell Station Activates DND Indicator on All Keypads Disables Doorbell Button Disables House Keeping Indication on System Up Arrow Raises Heating Cooling Set Point Middle Button Not Used Down Arrow Lowers Heating Cooling Set Point House Keeping Activates House Keeping Indicator on Doorbell Station Activates House Keeping Indicator on All Keypads Disables DND Indication on System Drapes Open Momentary Press Opens Bedroom Drapes Fully Press and Hold Opens Drapes Stops on Button Release Drapes Closed Momentary Press Closes Bedroom Drapes Fully Press and Hold Closes Drapes Stops on Button Release Stop Stops Drapes or Sheers Travel Open or Closed Sheers Open Momentary Press Opens Bedroom Sheers Fully Press and Hold Opens Sheers Stops on Button Release Sheers Closed Momentary Press Closes Bedroom Sheers Fully Press and Hold Closes Sheers Stops on Button Release 17 What it Does Sends Scene Activate to nodes in Group 1 Se
20. rts Ascii and extended codes XXXXX 1XX Supports Unicode XXXX 1 XXX Supports Ascii and Player codes COMMAND_CLASS_SCREEN_META_DATA Version 1 The Screen Meta Data command is used to write custom text to the screen GET REPORT y 6 5 4 3 2 1 0 COMMAND CLASS SCREEN MD SCREEN MD REPORT More Data Reserved Screen Settings Char Presentation 0 Clear 0 Standard Ascii Codes 0 1 Scroll Down 2 Scroll Up 7 Do not change content Line Settings A Clear A Line Number A 0 Chars written in std font 0 1 0 Button Area 1 1 Chars written highlighted 1 Button Area 2 2 Chars written in larger font 2 Button Area 3 EVLCD Z Wave Specification Rev G 12 Ev lve 3 Button Area 4 4 Button Area 5 Character Position A Number of Characters A Char 1 A Char N A Line Settings B Clear B Line Number B 0 Chars written in std font 0 1 0 Button Area 1 1 Chars written highlighted 2 Chars written in larger font 1 Button Area 2 2 Button Area 3 3 Button Area 4 4 Button Area 5 Character Position B Number of Characters B Char 1 B Char N B Notes 1 Text is always centered within the LCD display 2 Double lines can be assigned to a given button by using the CR 0x0d as a linefeed It will default to the smaller font when using double lines COMMAND_CLASS_POWER_LEVEL
21. t Says What it Does LIVINGROOM AIOR RIGHT Turns ON all Living Room Lights All Off Turns OFF all Living Room Lights Mood Sets Living Room lights to 40 Turns OFF all non dimmables Ceiling Turns ON all Living Room Ceiling Lights Turns OFF Perimeter Lights Ignores Lamps Perimeter Turns ON all Living Room Perimeter Art Lights Turns OFF Ceiling Lights Ignores Lamps EVLCD Z Wave Specification Rev G 15 lve LIVINGROOM 3GANG What it Says What it Does All On e Turns ON all Living Room Lights All Off e Turns OFF all Living Room Lights Mood e Sets Living Room lights to 40 e Turns OFF all non dimmables Ceiling e Turns ON all Living Room Ceiling Lights e Turns OFF Perimeter Lights e Ignores Lamps Cinema e Sets Living Room Perimeter Art Lights to 40 e Turns OFF Ceiling Lights e Closes Drapes e Ignores Lamps Do Not Disturb e Activates DND Indicator on Doorbell Station e Activates DND Indicator on All Keypads e Disables Doorbell Button e Disables House Keeping Indication on System Up Arrow e Raises Heating Cooling Set Point on Living Room HVACs a e Middle Button Not Used Down Arrow e Lowers Heating Cooling Set Point on Living Room HVACs House Keeping e Activates House Keeping Indicator on Doorbell Station e Activates House Keeping Indicator on All Keypads e Disables DND Indication on System Drapes Open e
Download Pdf Manuals
Related Search