USER MANNUAL
Contents
1. flash 36X1W LED PAN scan angle 0 540 TILT scan angle 0 230 UNPACKING LEDMH100 MINI LED FIXTURE XUSER MANUAL SAFETY WARNING For your convenient and accurate operation please read following information carefully Suitable for indoor use only Put it in a dry well ventilated place in case of short cut caused by erosion of moisture and rain Do not install it nearby hot sources in case that rising temperature of lamp damages LEDMH100 MOVING HEAD itself Do not barrier vent in order to ventilate well and dissipate in time Connect the fixture with power source which has a ground line and voltage of power source should accord with rating voltage fuse was damaged change the same type You can only choose accessories the manufacturer provides when need repairing Ambient temperature of the lamp should not exceed 40 C lf any problem contact with professional technicians working in our after sales service department PANEL REVIEW Fun Down Up Enter Press FUN button Switch to function menu or return to previous menu Press UP DOWN Adjust current activated field If the four point twinkle indicating value has been changed Press ENTER Enter into sub menu or confirm the current value INSTALLATION AND SETTING 1 MULTI FIXTURES CONNECTION DMX fixtures are designed to receive data through a serial Daisy Chain A Daisy Chain connection is where the DATA OUT of one fix2. 200 2204 255 AUTO PROA AUDIO PRO CH2 Red O 24 CH3 Green CH1 0 24 CH1 25 255 Auto speed as los The slowest CH6 Dimmer CHI 0524 255 PAN TILT Speed The slowest CH10 Pan Fine CH11 Tilt Fine TILT Adjustment 3 CHANNEL FUNTIONS DISPLAY FUNCTION VALUE 001 501 DMX address 16BT is on the max value is 501 MODE M DM DMX mode AUTO mode Notes Only one lamp can be set as Master and the left are Slaves Slaves set to DMX mode with DMX address 001 Do not connect the Slaves lamp with controller SOUND mode Notes Only one lamp can be set as Master and the left are Slaves Slaves set to DMX mode with DMX address 001 Do not connect the Slaves lamp with controller PRCO PR1 8 8 built in programs LEDMH100 MOVING HEAD Pr1 4 means skip anar ae Run clockwise as DMX value increases REV Run anticlockwise as DMX value decreases R TILT STND Run clockwise as DMX data increase REV Run anticlockwise as DMX data decreases r PT CH7 PAN CH8 TILT CH10 PAN FINE CH11 TILT FINE CH7 TILT CH10 PAN FINE CH11 TILT FINE TEST DISP STND Display bites normally REV Display bytes upside down REST REST ON Reset Press ENTER button to enter into REST menu and the screen reads flashing REST Then press UP DOWN button and the screen reads flashing ON If to press ENTER again the light engine re
3. LEDMH100 MOVING HEAD LEDMH100 USER MANUAL LEDMH100 MOVING HEAD TABLE OF CONTENTS INTRODUC nn PPP oo 3 MAIN EVN Sse atv ieee ee vi lv in een dada 3 A S e ras 3 SAME NE VAGA 3 FANELREVIEW uso aaa aaa 4 INSTALLATION AND SETTIN O contra 4 1 M ETI FIXTURES GONNEGT ION 4 2 LAMP BOD VANSTAELATION caia 5 musa a 5 oE TDIPOWITCOHE S mmm 5 2ADMX CHANNEL SUMMAR currada 6 a i a i a a a 6 4 ABOU EACIY CHANNEL 7 MAINTENANCE ataman mamma kisas 11 TIES Sis la IN 11 2 GLEANING ausam 11 TECHNICAL SPECIFICATION aaa 12 APRENDO teo 12 LEDMH100 MOVING HEAD INTRODUCTION Thanks for your purchase of our product mini led moving head fixture can works under auto mode and sound active mode with 16 built in programs The product has a long lifespan and low power consumption lt is exquisite and applicable for all kinds of entertaining occasions Before you begin please read instructions carefully lf you meet with any problem please contact with your distributor nearby MAIN FEATURES DMX 512 control 11 channels DMX AUTO SOUND ACTIVE mode RGB control with 255 grades RGB total dimmer is 0 100 Shutter speed is 10flashes sec 10secs
4. efficienCy 3 8 Im w Optic angle 23 DimensiOn L250XW 220XH376 MM Weight 2 9 nene meene 222 28 TKG
5. rformance because of over heat after working for some time Second lens cleaning and maintenance LEDMH100 MOVING HEAD To ensure the best effect of lamp please clean every lean or reflective setting Use the soft cotton with some lotion to clean it but do not damage lens Third check line during a certain time Check connecting line wiring and ground line to ensure safety of using lamp during a certain time Forth mechanical transmission part maintenance Check mechanical transmission part if it has any loose part during a certain time such as a strap Abrasion of mechanical transmission part will affect stability of lamp work If strap is loose you should change it if needed TECHNICAL SPECIFICATION LEDMH100 MINI LED MOVING HEAD LED Number Voltage 36X1W LED POWO Teran nnn nnn nn nnn nn nnn nn nnn nn nnn nn nnn nnn nnn nnn nnn nnn nnn nnn nnn nena 160W Voltage 220V Electrical current 0 726A Total lumenS 528 15 1m Max light intensity 1089 cd Lamp
6. sets again TILT is 16 bit CH10 PAN FINE CH11 TILT FINE OFF PAN TILT is 8 bit CH10 CH11 does not exist 4 ABOUT EACH CHANNEL m Channel 1 DMX MODE Red Strobe 0 24 RGB 0 255 Speed 0 255 CH1 1 2 function function function speed 75 99 program LEDMH100 MOVING HEAD 100 124 Built in program 4 125 140 Built in program 5 150 174 Built in program 6 175 190 Built in program 7 200 224 Built in program 8 Sound active 225 255 program A u Channel 2 RED When CH1 0 24 DMX value red 255 carmine 0 0 Channel 3 GREEN When CH1 is 0 24 DMX value green 299 pottle green LEDMH100 MOVING HEAD m Channel 4 Blue When CH1 is 0 24 DMX value 255 Channel 5 Strobe When CH1 is 0 24 DMX value 255 16 15 blue navy blue strobe speed slowest fastest no strobe no strobe When CH1 is 25 224 DMX value 295 AUTO speed slowest LEDMH100 MOVING HEAD 0 fastest m Channel 6 RGB Dimming When 0 24 DMX value RGB brightness 255 0 0 brightest Channel 7 PAN 540 ei Rightmost Bottommost ee en 1 m Channel 9 PAN or TILT SPEED m Channel 10 PAN FINE 2 4 m Channel 11 TILT FINE 2 42 Notes When 16 BT is on CH10 CH11 exists otherwise they do not exist LEDMH100 MOVING HEAD MAINTENANCE 1 TROUBLESHOOTING Probable cause s Suggested remedy Check if power
7. source is on or cord works No power source t well Cut off power source and change the Fixtures does not same type fuse If fuse was burnt on end work it may be the problem of connection Find Fuse burnt ee qualified professors to repair Check repair or change the data line False or incomplete data Ensure connection is well and the first connection lamp s single input is connected with the controller output False address setting Check DMX address Reset normally but console abnormally or no response Problem of signal Pull out the signal output and input of one connector of some fixture Then connect both directly If it fixtures works well this fixture is proved to be the failed one Handle the rest fixtures alike to check which fixture has problems If any problem please connect the technician Signal output does not Toggle the PHASE button on the match with the pin pins2 controller to reverse the polarity and pins3 has a wrong seguence 2 CLEANING Though increasing reliability by designing well and we never stop to improve guality to lengthen lamp s lifespan It is still indispensable to maintain it well by certain time in order to ensure best performance First clean fan and vent Favorable heat dissipation and ventilation is vital to lamp s normal work So clean the fan and vent during a certain time to guarantee smooth of wind path Otherwise dust will barrier vent which will affect the pe
8. ture connects to the DATA IN of the next fixture The order in which the fixtures are connected is not important and has no effect on how a controller communicates to each fixture Use an order that provides for the easiest and most direct cabling Connect fixtures using shielded two conductor twisted pair cable with three pin XLR male to female connectors LEDMH100 MOVING HEAD Controller S 2 LAMP BODY INSTALLATION Notes do not install it nearby the curtain or flammable materials Only for indoor use OPERATION 1 SET DIPSWITCHES Each fixture occupies 11 DMX channels DMX 512 signal can control multi fixtures together however you must set DMX address of each lamp first Different DMX address will lead to different movements You can set DMX address from 1 501 on the multi function display panel Switch on power supply and after finishing resetting the panel will show 001 is to say DMX address is 1 and the first lamp has been controlled by 1 11channels In turn the second fixture has been controlled by 12 22 channels When panel shows 001 press UP button until it shows 012 Then just press ENTER button In the same way the third fixture has been controlled by 23 33 channels and the panel shows023 Through this method you can control multi fixtures to perform different movements LEDMH100 MOVING HEAD 2 DMX CHANNEL SUMMARY DMX Channel control n a hi 174 AUTO PRO 3 AUTO PRO 4 t
Download Pdf Manuals
Related Search