FLAT PAR TRI18XS - Amazon Web Services
Contents
1. www adj com FLAT PAR TRI18XS User Manual Page 21 FLAT PAR TRI18XS Introduction Unpacking Thank you for purchasing the FLAT PAR TRI18XS by ADJ Products LLC Every FLAT PAR TRI18XS has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during ship ping If the carton appears to be damaged carefully inspect your fix ture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are missing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contacting customer support Introduction The ADJ FLAT PAR TRI18XS is part of a continuing pur suit to create high quality intelligent lighting The FLAT PAR TRI18XS is a DMX intelligent high powered LED par fixture This fixture can be used in a stand alone mode or connected in a Master Slave configura tion This wash has five operating modes Sound Active mode Auto mode RGB mode Static Color mode and DMX control mode Customer Support ADJ provides a customer support line to pro vide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific St2. dEFA is displayed 3 Press the UP and DOWN buttons simultaneously Press the MODE button to exit Infrared Receiver This function is used to activate and deactivate the infrared receiver When this function is activated you can control the fixture using the ADJ LED RC Remote Control Please see the next page for ADJ LED RC controls and functions 1 Plug the fixture in and press the MODE button until dXX is dis played XX represents either on or OFF 2 Press the SET UP button until IrXX is displayed XX represents either on or oF 3 Press the UP or DOWN buttons to either activate the remote func tion On or deactivate it Off FLAT PAR TRI18XS Master Slave Configuration Master Slave Configuration This function will allows you to link units together to run in a Master Slave mode In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units built in programs Any unit can act as a Master or as a Slave however only one unit can be pro grammed to act as the Master Master Slave Connections and Settings 1 Daisy chain your units via the XLR connector on the rear of the unit Use standard XLR data cables to link your units together Remember that the Male XLR connector is the input and the Female XLR con nector is the ouput The first unit in the chain master will use the female XLR connector only The last
3. evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Produ
4. programs Static Color Mode There are 7 colors to choose from e Auto Mode There are 3 Auto Modes to choose from RGB Mode Choose one of the three colors to remain static or adjust the intensity of each color to make your desired color DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX 512 controller Sound Active Mode In this mode the FLAT PAR TRI18XS will react to sound and chase through the different colors 1 Plug the fixture in and press the MODE button until So X is dis played X represents the sound active mode 1 8 currently dis played 2 The fixture will now change via sound 3 Press the SET UP button to adjust the sound sensitivity SJ X should be displayed Use the UP or DOWN buttons to adjust the ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 7 FLAT PAR TRI18XS_ 7 Channel DMX Values amp Functions VALUE FUNCTION ma 1 255 0 100 1 255 0 100 BLUE 1 255 0 100 1 2 4 COLOR MACROS See 1 Channel DMX mode for colors 0 15 16 255 1 3 5 STROBING PROGRAM SPEED NOTHING STROBING SPEED CONTROL SLOW FAST PROGRAMS 0 127 128 135 136 143 144 151 152 159 160 167 168 175 176 183 184 191 192 199 200 207 208 215 216 223 224 231 232 239 240 247 248 255 aos 1 255 Channels 1 2 and 3 will not work when Channel 4 is being use
5. unit in the chain will use the male XLR connector only 2 Connect the first Slave unit to the Master 3 Set the Master unit to your desired mode of operation The Slave unit will now follow the Master ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 10 FLAT PAR TRI18XS ADJ LED RC Operation The ADJ LED RC infrared remote sold seperately has many differnet functions and gives you complete control of your FLAT PAR TRI18XS To control the your desired fixture you must aim the controller at the front of the fixture and be no more the 30 feet away To use the ADJ LED RC you must first activate the fixtures infrared receiver to acti vate the receiver please see the instructions on page 10 BLACKOUT Pressing this button will blackout the fixture AUTO RUN This button will run an automatic program You can con trol the speed of the Auto Run by pressing the SPEED button first and then pressing the and buttons PROGRAM SELECTION This button will let you access the units built in programs Pressing this button and then press the or to navigate through the built in programs FLASH This button will activate the strobe effect You can control the flash rate by pressing the and buttons Press this button again to exit strobe mode SPEED Press this button and use the amp buttons to adjust the speed of the Auto run DM
6. will not work when Channel 4 is being 3 When G XXX is displayed you are in Green dimming mode Press used the UP and DOWN buttons to adjust intensity 4 When b XXX is displayed you are in Blue dimming mode Press the UP and DOWN buttons to adjust intensity 5 After you have adjusted the RGB colors to make your desired color you can then activate strobing by pressing the SET UP button to ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 15 ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 8 FLAT PAR TRI18XS Operating Instructions FLAT PAR TRI18XS_ 2 Channel DMX Values amp Functions 6 FS XX will be displayed this is Flash mode The Flash can be adjusted between FS 00 flash off to FS 15 fastest flash 1 255 COLOR MACROS See 1 Channel DMX mode for colors DMX Mode 1 255 DIMMER 0 100 Operating through a DMX controller gives the user the freedom to cre ate their own programs tailored to their own individual needs This FLAT PAR TRI18XS 3 Channel DMX Values amp Functions function also allows you to use your fixtures as spot lights The FLAT PAR TRI18XS has 7 DMX modes 1 Channel lee Channel mode 3 wee Channel mode 4 Channel mode 5 Channel mode 6 Channel mode and 1 RED a 7 Channel mode See pages 13 16 for each modes DMX traits a 1 255 0 100 1 This function will allow you to control each individual fixture s traits 2 GREEN with a standard D
7. ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Follow Us On Junostraat 2 f t to 6468 EW Kerkrade Netherlands facebook com americandj service adjgroup eu www adj eu twitter com americandj youtube com adjlighting Tel 31 45 546 85 00 Fax 31 45 546 85 99 4 15 User Instructions 2015 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indi rect economic loss associated with the use or reliance of any information contained within this document
8. MX 512 controller a 1 255 0 100 2 Torun your fixture in DMX mode press the MODE button until 2 d XXX is displayed XXX represents the current displayed ad 3 BLUE dress Use the UP or DOWN buttons to select your desired DMX 1 255 0 100 address then press the SETUP button to select your DMX Channel mode FLAT PAR TRI18XS 4 Channel DMX Values amp Functions 3 Use the UP or DOWN buttons to scroll through the DMX Channel modes The Channel modes are listed below To run the 1 Channel Mode press the MODE button until Ch 01 are RED is displayed This is the 1 Channel DMX Mode 1 255 0 100 To run the 2 Channel Mode press the MODE button until Ch 02 2 GREEN is displayed This is the 2 Channel DMX Mode 1 255 0 100 To run the 3 Channel Mode press the MODE button until Ch 03 3 BLUE is displayed This is the 3 Channel DMX Mode 1 2 1009 To run the 4 Channel Mode press the MODE button until Ch 04 29 o os cee fe 4 MASTER DIMMER is displayed This is the 4 Channel DMX Mode 1 6 1 T 255 0 a 100 To run the 5 Channel Mode press the MODE button until Ch 05 is displayed This is the 5 Channel DMX Mode To run the 6 Channel Mode press the MODE button until Ch 06 is displayed This is the 6 Channel DMX Mode To run the 7 Channel Mode press the MODE button until Ch 07 is displayed This is the 7 Channel DMX Mode Please see pages 13 16 for DMX values and traits After you
9. X MODE This button will let you select which DMX mode you want to use Some fixtures will come with different DMX channel modes This button will switch between the different modes Please see pages 13 16 for DMX modes values and traits SOUND ACTIVE This button activates sound active mode SLAVE This designates the fixture as a slave fixture in a master slave configuration SET ADDRESS Press this button to set the DMX address Press this button first then press the numbers to set the address Example Set DMX Address 1 Press S 0 0 1 Set DMX Address 245 Press S 2 4 5 R G B Press either one of these buttons and the press the or to adjust the brightness and Use these buttons to adjust the flash rate speed of the Auto Run sound sensitivity and program selection ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 11 FLAT PAR TRI18XS ADJ LED RC Operation DMX Control Operating through an DMX controller gives the user the freedom to create their own programs tailored to their own individual needs Follow the directions below to set your DMX Mode and address 1 Before connecting to an DMX controller your fixture has different DMX channel modes please select your desired mode by press ing the DMX Mode button then using the or buttons to scroll through the DMX Channel Modes Set the mode before you address the fixture See the bottom of this pag
10. an dard Time Voice 323 582 3322 Fax 323 582 3108 E mail support AmericanDJ com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ PLEASE recycle the shipping carton when ever possible ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 2 FLAT PAR TRI18XS General Instructions To optimize the performance of this product please read these operat ing instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference FLAT PAR TRI18XS e Multi Colors e Five Operating Modes e Electronic Dimming 0 100 e Built in Microphone e DMX 512 protocol 3 Pin DMX Connection Seven DMX Modes 1 Channel Mode 2 Channel Mode 3 Channel Mode 4 Channel Mode 5 Channel Mode 6 Channel Mode and 7 Channel Mode Snoot Frame Included to help limit unwanted light exposure e ADJ LED RC compatiable Not Included Power Cord Daisy Chain See page 17 FLAT PAR TRI18XS Warranty Registration The FLAT PAR TRI18XS carries a 2 year limited warranty Pleas
11. and or as a result of the improper unsafe unsufficient and negligent assembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipment from power when not in use Thank you FLAT PAR TRI18XS Specifications Model FLAT PAR TRI18XS Voltage 100V 240V 50 60Hz LEDs 18 x 3 Watt 3 in 1 LED s 54 Watts Total Beam Angle 40 Degrees Working Position Any safe working position Power Consumption 56W Power Cord Daisy Chain 10 Fixtures Max Fuse 1 Amp Weight 8lbs 3 3Kgs Dimensions 13 L x 11 W x 4 25 H 328 x 280 x 105mm RGB Color Mixing 7 DMX Modes 1 Channel Mode 2 Channel Mode 3 Channel Mode 4 Channel Mode 5 Channel Mode 6 Channel Mode amp 7 Channel Mode Warranty 2 Year 730 days Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice Colors DMX Channels ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 22 FLAT PAR TRI18XS Notes ADJ Products LLC
12. ceiling hanging sideways on trussing or set on a flat level surface The unit should be mounted using a mounting clamp not provided affixing it to the mounting bracket that is provided with the unit Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit s weight Also always use a safety cable that can hold 12 times the weight of the unit when installing the fixture The equipment must be installed by a professional and it must be installed in a place where it is out of the reach of people s grasp FLAT PAR TRI18XS Disconnect the unit from its power source Remove the power cord from the unit Once the cord has been removed you will find that the fuse holder is located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder also has a holder for a spare fuse Power Cord Daisy Chain Installation Fuse Replacement ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 17 FLAT PAR TRI18XS Set Up Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in c
13. cts LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential ari
14. d OFF COLOR DREAMING 1 COLOR DREAMING 2 COLOR DREAMING 3 COLOR DREAMING 4 COLOR DREAMING 5 COLOR DREAMING 6 COLOR DREAMING 7 COLOR DREAMING 8 COLOR CHANGE 1 COLOR CHANGE 2 COLOR CHANGE 3 COLOR CHANGE 4 COLOR CHANGE 5 COLOR CHANGE 6 SOUND ACTIVE MODE 1 SOUND ACTIVE MODE 2 MASTER DIMMER 0 100 When using Channel 6 values 128 239 Channel 5 will control the speed of the programs When using Channel 6 values 240 255 Channel 5 will control the sound sensitivity ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 16 FLAT PAR TRI18XS_ 5 Channel DMX Values amp Functions FLAT PAR TRI18XS Operating Instructions Channel Value Function s_ sensitivity SJ 1 is the lowest sensitivity SJ 8 is the highest 1 2 0 100 1 Plug the fixture in and press the MODE button until CL X is dis 2 GREEN played 1 255 0 100 2 There are 7 colors to choose from Select your desired color by 3 BLUE pressing the UP and DOWN buttons After you have selected your 1 255 0 100 desired color you can activate strobing by pressing the SET UP but ton to enter the Flash strobe mode 4 MASTER DIMMER 3 FS XX will be displayed this is Flash mode The Flash can be 1 255 0 100 adjusted between FS 00 flash off to FS 15 fastest flash 5 1 255 COLOR MACROS See 1 Channel DMX mode for colors Auto Mode There are 3 types of Auto Modes to choose from Color Fade C
15. e fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper included in the shipping carton If the unit is under warranty you must provide a copy of your proof of purchase invoice You may obtain a R A number by contacting our customer support team on our customer support number All pack ages returned to the service department not displaying a R A number on the outside of the package will be returned to the shipper Features ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 3 FLAT PAR TRI18XS Notes ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 20 FLAT PAR TRI18XS Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable
16. e for the DMX modes 2 After you have selected your mode set the DMX address for the fixture by pressing the S button When the S button is pressed the LED s will flash 2 3 times and all the red LED s will light Use the number buttons to press in your desired address See SET ADDRESS on page 11 for examples Note When seeting the DMX address each time a number is pressed a LED color will glow when you have set the DMX address correctly all LED s will flash 2 3 times 3 Now you may connect the fixture via the XLR connections to any standard DMX controller Please see pages 13 16 to for a detailed descriptions of the DMX modes values and traits If the Red LED s glow you are in DMX Mode 1 1 DMX Channel If the Green LED s glow you are in DMX Mode 2 2 DMX Channels If the Blue LED s glow you are in DMX Mode 3 3 DMX Channels If the Red amp Green LED s glow you are in DMX Mode 4 4 DMX Channels If the Red amp Blue LED s glow you are in DMX Mode 5 5 DMX Channels If the Green amp Blue LED s glow you are in DMX Mode 6 6 DMX Channels If all of the LED s glow you are in DMX Mode 7 7 DMX Channels ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 12
17. een spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 4 FLAT PAR TRI18XS Set Up Power Supply The ADJ FLAT PAR TRI18XS contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 ma
18. have chosen your desired DMX Channel mode plug in the fixture via the XLR connections to any standard DMX controller a Default Running Mode This is a default running mode When this mode is activated all modes ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 9 ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 14 Function COLOR MACROS l r BASTARD AMBER 8 15 MEDIUM AMBER 16 23 PALE AMBER GOLD 24 31 GALLO GOLD 32 39 GOLDEN AMBER 40 47 LIGHT RED 48 55 MEDIUM RED 56 63 MEDIUM PINK 64 71 BROADWAY PINK 72 79 FOLLIES PINK 80 87 LIGHT LAVENDER 88 95 SPECIAL LAVENDER 96 103 LAVENDER 104 111 INDIGO 112 119 HEMSLEY BLUE 120 127 TIPTON BLUE 128 135 LIGHT STEEL BLUE 136 143 LIGHT SKY BLUE 144 151 SKY BLUE 152 159 BRILLIANT BLUE 160 167 LIGHT GREEN BLUE 168 175 BRIGHT BLUE 176 183 PRIMARY BLUE 184 191 CONGO BLUE 192 199 PALE YELLOW GREEN 200 207 MOSS GREEN 208 215 PRIMARY GREEN 216 223 DOUBLE CTB 224 231 FULL CTB 232 239 HALF CTB 240 247 DARK BLUE 248 255 WHITE FLAT PAR TRI18XS 1 Channel DMX Values amp Functions ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 13 FLAT PAR TRI18XS Operating Instructions will return to their default settings 1 Plug the fixture in and press the MODE button until dXX is dis played XX represents either on or OFF 2 Press the SET UP button until
19. olor Change and both modes running together The running Channels 1 2 and 3 will not work when Channel 5 is being speed is adjustable in all 3 modes used 1 Plug the fixture in and press the MODE button until either AF X R AJ X or A JF is displayed FLAT PAR TRI18XS_ 6 Channel DMX Values amp Functions e AF X Color Fade mode there are 8 Color Fade modes to choose Channel Value Function from Use the UP or DOWN buttons to scroll through the different 1 RED Auto Fade modes AJ X Color Change mode there are 8 Color Change modes to I 0 100 choose from Use the UP or DOWN buttons to scroll through the GREEN different Auto Change modes 1 255 0 100 A JF Both Color Fade and Color Change modes running BLUE 2 After you have chosen your desired running mode press the SET UP 1 255 0 100 button until SP XX is displayed When this is displayed you can adjust the running speed of your desired program Use the UP or DOWN button ean the tae nian SPO slowest and See 1 r O DMX mode for colors SP 16 fastest Once you have set your desired running speed press the SET UP button to return to your desired Auto Mode 0 15 oie ERI 255 STROBING SLOW FAST RGB Dimmer Mode MASTER DIMMER x n ua a ihe the ein sea until Pe m i en r is displayed you are in Red dimming mode Press the p 299 0 100 UP and DOWN buttons to adjust intensity 1 2 and 3
20. ontact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON XLR Male Socket DMX512 OUT 3 PIN XLR D Figure 2 XLR Pin Configuration 1 1 i 1 Ground 1 2 Cold 2 Cold 1 Ground Pin 1 Ground i Pin 2 Data Compliment negative i i I J Pin 3 Data True positive ee Figure 3 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems 0 and interference It is always advisable A 2 to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The cha
21. ound prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside e Never operate this unit when it s cover is removed e Never plug this unit in to a dimmer pack e Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged e This unit is intended for indoor use only use of this product out doors voids all warranties During long periods of non use disconnect the unit s main power e Always mount this unit in safe and stable matter e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 18 for cleaning details e Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu ding amplifiers that produce heat The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has b
22. r which way the inputs and outputs are connected Unit does not respond to sound 1 Quiet or high pitched sounds will not activate the unit 2 Make sure that Sound Active mode is activated FLAT PAR TRI18XS Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses must be carried out periodically to optimize light output 1 Use normal glass cleaner and a soft cloth to wipe down the outside casing 2 Clean the external optics with glass cleaner and a soft cloth every 20 days 3 Always be sure to dry all parts completely before plugging the unit back in Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew Cleaning ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 18 FLAT PAR TRI18XS Photometric Chart R D40 1320 850 155 82 2 51 5 S D40 1060 285 116 6 66 9 43 8 B Do 1m3 _308 126 5 74 8 466 j lux RGB D40 2920 l 791 355 193 123 5 Distance m FLAT PAR TRI18XS With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 10 fixtures maximum After 10 fixtures you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures FLAT PAR TRI18XS The FLAT PAR TRI18XS is fully operational in three different mount ing positions hanging upside down from a
23. rt below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Ground Shield Pin 1 Data Compliment signal Pin 2 Data True signal Pin 3 Not Used Do Not Use Not Used Do Not Use ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 6 FLAT PAR TRI18XS Operating Instructions LED Display On Off To set the LED display to turn off after 10 seconds press the MODE but ton until don is displayed press the UP button to display doff Now the display will disappear after 10s Press any button to turn the display on again Be advised though that the display will turn off automatically after 10 seconds To set the display press the MODE button until dXX is displayed Use the UP or DOWN buttons to select either don LED display on at all times doFF LED display shuts off after 10 seconds LED Display Inversion Follow these instructions to flip the display 180 so that the display can be read upside down 1 Plug the fixture in and press the MODE button until dXX is dis played XX represents either on or OFF 2 Press the SET UP button until Stnd is displayed 3 Press the UP or DOWN buttons to reverse the display 180 Operating Modes The FLAT PAR TRI18XS has five operating modes e Sound Active mode The unit will react to sound chasing through the built in
24. sing out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 1 Year 365 Days Limited Warranty excluding laser diodes which have a 6 month limited warranty e L ED Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty batteries which have a 180 day limited war ranty Only the L E D s carry a 2 year warranty excluding StarTec Series which a carries a 90 Day Limited Warranty e ADJ DMX Controllers 2 Year 730 Days Limited Warranty excluding faders and tact switches ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 19 FLAT PAR TRI18XS Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the gr
25. y be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The FLAT PAR TRI18XS can be controlled via DMX 512 protocol The FLAT PAR TRI18XS has 7 DMX channel modes please see page 9 for the different modes The DMX address is set on the back panel of the FLAT PAR TRI18XS Your unit and your DMX controller require a standard 3 pin XLR connec tor for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all pro lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Figure 1 ADJ Products LLC www adj com FLAT PAR TRI18XS User Manual Page 5 FLAT PAR TRI18XS Trouble Shooting Listed below are a few common problems the user may encounter with solutions Unit not responding to DMX 1 Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on some other DMX devices pin 2 may be hot Also check that all cables are connected to the right connectors it does matte
Download Pdf Manuals
Related Search