Home

view User`s Manual in format - COP

1. Step 4 Install other three HDD under the upper mounting bar as shown below 3 NVR User Manual Step 5 Cover the back cover of the device and tighten it 2 1 2 Install DVD Writer Notice 1 The writers must be the compatible devices we recommend Please refer to Appendix C Compatible Devices 2 This device is only for backup Step 1 Open the back cover and loosen the screws in the both sides of the case to take out of N the mounting bars as shown below Step 2 Loosen the four screws in the back of the front panel as shown below and then take out of the brace with a triangular mark 1f there is no such brace please skip this step Step 3 Install the DVD holder attached with the device Try to place the holder farther away from the front and then tighten it Then put the DVD with the holder into the case and tighten it Step 4 Connect the power and data cables and install the upper mounting bar Then tighten the screws in the both sides NVR User Manual Note If you install a DVD writer you can only install 4 HDD disks at most Because too much room has been taken up 2 2 Front Panel Descriptions Notice The front panel descriptions are only for reference please make the object as the standard type Name Function Indicator Function SEARCH Enter search mode in live Buttons Exit the current interface Manually record b Fast forward Input digital number and select ca
2. Alternate DNS Server 000 000 000 000 Default Fig 5 23 Network Configuration Network Step 2 Set HTTP port The default HTTP port is 80 If the value is changed you shall add the port number when typing IP address in IE address blank e g If HTTP port is set to 82 and IP address is http 192 168 0 25 you should input the following IP address http 192 168 0 25 82 into IE browser Step 3 Set server port The default server port is 6036 Step 4 Connect internet There are three ways to connect internet gt If you have a DHCP server running and would like your NVR to automatically obtain an IP address and other network settings check the checkbox beside Obtain an IP address automatically Then the device will distribute IP address subnet mask and gateway IP and DNS server gt If you want to configure your own settings disable Obtain an IP address automatically item and input the IP address subnet mask gateway IP and DNS server 29 NVR User Manual gt If you connect internet through PPPoE disable Obtain an IP address automatically item and check PPPoE checkbox and then enter username and password Once the setup is completed your NVR will automatically dial up into your network Step 5 Test the effectiveness of the network by clicking Test button after you set up the network Step 6 If the network is well connected please click Apply button to save the setting 5 6 2 Email To
3. gt Before drag After drag 5 3 5 Recycle Record This option is used to recycle the HDD space once it is full If enabled the system will automatically delete the old records and recycle the space 1f 1t is completely utilized The setting steps are as follows Step 1 Enter into Menu gt Setup gt Record gt Recycle Record interface Step 2 Checkmark recycle record to activate auto recycling If the option is disabled or not selected the NVR would stop recording once HDD is full Step 3 Click Apply button to save the setting 5 3 6 Snap In this interface user can set up resolution quality snap interval snap number 5 4 Schedule Configuration Schedule configuration includes three sub menus schedule motion and sensor 5 4 1 Schedule This tab allows defining schedule for normal recording for seven days of a week 24 hours of a day Every row denotes an hourly timeline for a day Click the grid to do relevant setup A highlighted area denotes selected timeline Operate the following steps to set schedule Step 1 Enter into Menu gt Setup gt Schedule interface Refer to Fig 5 14 SCHEDULE Motion Sense Channel CNI CICI 04 00 Sunday Monday Tuesday Wednesday L hursday Friday Salurday Apply Settings To LA Detail Fig 5 14 Schedule Configuration Schedule 23 NVR User Manual Step 2 Select channel and click Ea button to add a certain day schedule Click Ed button to delete the selec
4. Apply to save the setting ono Mask Display Mode ES x 2 Chantel 37 Y Gefsult Apply Fig 5 7 Live Configuration Main Monitor 5 2 3 Mask If there is something you don t want to display in the live image you can set mask For a given channel a maximum of three areas can be masked If the mask function is not available in the added IP camera the mask function here will not take effect To set up mask area Step 1 Enter into Menu gt Setup gt Live gt Mask interface e Main Monitor M Mack Areg Satin Setting Sethricg Setting Setting Seating Setting Metal Fig 5 8 Live Configuration Mask 19 5 3 NVR User Manual Step 2 Click Setting button to go into live image Step 3 Press and drag the left mouse button to set mask area as shown below Step 4 Right click to exit the mask setting interface Step 5 Click Apply button to save the setting To delete mask area Step 1 Click Setting button in the mask interface Step 2 Select a certain masked area and double click to delete that masked area Step 3 Then click Apply button to save the setting Fig 5 9 Setting Mask Area Record Configuration Record configuration includes six sub menus enable record bit rate time recycle record stamp and snap Before Configuration please make sure your NVR has been installed with HDD and has completed its initialization 5 3 1 Enable Step 1 Enter into Menu gt Setup gt Record gt Enable tab
5. 000 Default Fig 5 30 Block Allow List Here authorized user can prohibit computer users within a certain IP address range from accessing to NVR or allow computer users within a certain IP address range to access NVR E g 1f an admin user doesn t want computer users within IP address range from 192 168 000 002 to 192 168 000 004 to access the NVR he can check Block list option and then input such IP address range 3 6 1 NVR User Manual Search Playback amp Backup Search configuration includes four submenus time search event search file management and image Time Search Step 1 Enter into Menu gt Search gt Time Search Refer to Fig 6 1 SEARCH Fig 6 1 Search Configuration Time Search Step 2 Select date and channels on the right hand side and press the Search button A date with highlighted borderline indicates presence of data Step 3 Set the start time by clicking a particular grid or by entering the specific value in the start time field Step 4 Select the channel display mode and click Play gt button to play record Use the playback toolbar to control the playback Pause Play Frame Backward E zoom Cut lt A HQ X Camera Name Hive Move Tool lt L p a ee ee AAIIIIIIIIIIDIII AN gt gt gt gt Stoph F orwardiWScreen Model Color gt gt 1X 6 2 Event Search Step 1 Enter into Menu gt Search gt Event Search button Refer to Fig 6 2 Step 2 Select
6. 40 7 4 7 5 NVR User Manual space and total space at the bottom of screen Step 2 Click Refresh button to refresh the disk information in the list box Step 3 Select a hard disk and click Format button to start format Note All recorded files in the hard disk will be lost once it is formatted 2 Advanced User may check model S N firmware health status of the disk in this interface User also can monitor the temperature internal circuit dielectric material of the disk analysis the potential problems of the disk and warn so as to protect its data Upgrade The NVR can be upgraded by using USB flash drive Get the upgrading software from your vendor when there is a new software version Upgrade Steps Step 1 Copy the upgrade software which gets from vendor into the USB storage device Step 2 Connect the USB flash drive to the USB port Step 3 Enter Menu Upgrade tab Then the upgrade software name would be displayed in the upgrade list box Step 4 Select that software and then click upgrade button It will upgrade automatically Note Please wait for a while when the system reboots Never cut off power during upgrading The original configuration will be reserved after upgrade Logoff Enter into Menu gt Logoff tab A log off dialogue box will pop up The device will log off by clicking OK button If you want to log in again click Menu icon to enter into user name and password to re login 41
7. Refer to Fig 5 10 Step 2 Checkmark record and audio 1 RECORD ible Record Bitrate Time Stamp HRecycle Record Snap Audio Fig 5 10 Record Configuration Record 20 NVR User Manual To enable disable recording for the channel To enable disable audio recording for the channel Step 3 Select All to set up the same settings for all channels 5 3 2 Record Bitrate Step 1 Enter into Menu gt Setup gt Record gt Record Bitrate Refer to Fig 5 11 Step 2 Setup rate resolution quality encode and max bit stream Step 3 Select All to set the same settings for all channels Step 4 Click Apply button to save the setting RECORD Enable fre cord EF irate Chi saalily Max Erias J Higher 11536 kbps p gt _ gt m gt Higher 11536 kbps Higher 1536 kbps ioar Miter jt ao EDHE EUR Higher 1536 kbps EDF Higher 1536 kbps 080E F CAR T Higher 1536 kbps Defaut Fig 5 11 Record Configuration Record Bitrate P arameter T Meaning Rate Range from 1 30 NTSC 1 25 PAL Resolution Supports1080P 720P D1 The higher the value is the clearer the recorded image is Six Quality options lowest lower low medium higher and highest Encode VBR and CBR Max bit stream Range from 256 12288kbps If the value of the parameter is set to exceed the maximum resources of the system the system will automatically adjust it 5 3 3 Time Step 1 Enter into Menu gt Setup
8. o A A A 11 Ae Ps TP CAMO Pas A A O A O E E E 13 S Main Menu Setup Guide sec scwssscavciscssscecscecnsasseesesevecectvesssoscuaussectveesseseuatece cevaswsestuatecessaceusnseccesses 15 Sol Basic cont onra OM e a S 16 A E er E al ate Morena E O E 16 TEDi Oe Me aan a a A BED EEN SEES EE 20 FORE SEE 0002 0100 a a 17 O VA ao 17 922 ive Conhoiarn O A AN 18 A A O O 18 IAZ NAO a 19 I2 S WSK A2 442729 2400224 1128 2000122 12 ERE ced Lowttec tee 220 102022402 120 2020424 172407 172202907 19 STER RECOnd C Oi BOUT ALON ad diia 20 A Pt RA LP dee tandcnaa E E A 20 323 2 RECOrA BIN AC ava tes cassscveae testbed canst beren Ra 21 oA Ki e le eO SEE 72 A D 2019022421292002 creda aera Weed AAAA E 120 2202722024 tie cathe 21 ASN 6 Se ee O 2207 20201009 RE 2A A 20 SEE DRA ee wee 22 5 355 RE e e oe DA 23 M N S E21 1621 A o q O sane cae 23 AA EE ae ee oe eee ad oe eal 23 De SCC AA O den bel PN Vu AN 23 34 2 Monton Schedule it A E L RAR CA tada 24 SAA O E 24 55 Alarm A Ed ea 23 SA anrea AN 23 55 2 MO orn ATA tt A it daba 26 RS Bo Vcd 05V 21 sn LOP 2027022 PP UE ee 2 0 9025 2 0 ERE TEE FEER a 28 SA Adai OUE 2422226 A aa Mace 0A S A A A G S eh e 28 S 6 Network Cono wao srun aa ae Latber Raba 29 IOl N TWOTK 2422354324 o LE ar ne reins e se 29 SEA lA ENT EA TEAT T E EE TENT T EAT EENT EE 30 IO S INV OE E E E EESE 30 SA a a a ale Aoa lC 31 5 7 User Management CO CUA ib 33 A II 35 3 8 V RESON 2232220029 L E DE De PY ae A eT 35 D2 MOT KOM sitiado is
9. 3Jelsjo zjeljo 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Mihi Ea M3 Hs jas Me Ez Me Mo Mio Mu Maz Ei Mis Mis Mie Lock Select certain file item in the file list box and then click Lock button to lock this file that ca not be deleted or overlaid Unlock Select a locked file and then click Unlock button to unlock this file Delete Select an unlock file and then click Delete button to delete this file from file list 8 4 2 Remote Backup Click Backup button to enter into backup interface Refer to Fig 8 8 9 2 Start Time End Time 2011 04 27 23 50 35 2011 04 28 00 12 48 2011 04 28 00 12 48 2011 04 28 00 34 58 2011 04 28 00 34 58 2011 04 28 00 57 07 2011 04 28 01 19 16 2011 04 28 00 57 07 2011 04 28 01 19 16 2011 04 28 01 41 34 T 2011 04 28 02 03 47 2011 04 28 02 03 47 2011 04 28 02 25 52 2011 04 28 02 25 52 2011 04 28 02 48 02 2011 04 28 02 48 02 2011 04 28 03 10 11 Start Time 2011 04 28 M8 00 00 00 End Time 2011 04 28 Fi 2011 04 28 03 10 11 2011 04 28 03 32 20 2011 04 28 03 32 20 2011 04 28 03 54 25 2011 04 28 04 16 35 2011 04 28 03 54 25 2011 04 28 04 16 35 2011 04 28 04 38 44 ao sr r qa fre lpo po po tl el ee el pe me D 2011 04 28 04 38 44 1 16 2011 04 28 05 00 53 FE Browse Backup Fig 8 8 Remote Backup Inte
10. Maybe HDD is full and thus the NVR is not able to record Check HDD information from Disk management and if required please enable the recycle function d Check the attributes of the HDD It might be set to read only mode e The HDD could have gone bad Please change another one Q7 Mouse does not work How can I do a The mouse should be connected to the USB port at the rear side b After connecting the mouse allow the NVR to detect the mouse for seconds If not detected try restarting the NVR 53 NVR User Manual c The mouse may be incompatible or faulty Please change a mouse OS ActiveX control cannot be downloaded How can I do a IE browser blocks ActiveX control Please do setup as per the steps mentioned below Open IE browser Click Tools Internet Options D about blank Microsoft Internet Explorer File Edit View Favorites Ms Help Mail and News i Synchronize Windows Update Show Related Links Internet Options Select Security Custom Level Refer to Fig 8 1 Enable all the sub options under ActiveX controls and plug ins Refer to Fig 8 2 Then click OK to finish setup b Other plug ins or anti virus may block ActiveX Please disable or do the required settings Internet Options f Security Settings General Security Privacy Content Connections Programs Advanced Settings Select a Web content zone to specify its security settings a Enable d
11. avi 06 25 29 fast forward previous file _ full screen play pause stop next frame next file path volume Fig 8 3 Record File Interface This NVR supports remote time search event search and file management By Time Search Step 1 Enter into Search gt Time search Refer to Fig 8 4 20 Sen Tua Wied Tha mi 5 Os Ds OF Cu 2 353 8 7 O Om Di On 9 10 11 12 MN Our Ou Os Om Har 16 17 18 19 20 2 Ela Era Elis Bs Fig 8 4 Time Search Interface Step 2 The highlight date in the area indicates recorded data Select the date in the area and record channels in area Step 3 Click Search button The record data will be displayed in the data information list box Step 4 Set the Start time and display mode in the area as required Step 5 Click play button to playback Step 6 Click the relevant buttons in the interface for operation like FF pause change channel mode research etc Please refer to Fig 8 5 48 J Pause NVR User Manual e A 03412012 09 07 31 Forward Next Frame Next Section Volume an lt Os Ow On 012 Dia O11 Ois O16 2012 03 14 F8 00 00 00 Playback By Event Search Step 1 Enter into Search gt Event Search Refer to Fig 8 6 Backward aia Stop Previous Section Full Screen Snap Picture Exit Fig 8 5 Time Search Playback 2010 01 09 00 02 16 2010 01 09
12. button Step 2 Disconnect the power By mouse Step 1 Enter into Menu and select Shut Down icon This will take you to a shutdown window Step 2 Click OK Then the unit will power off after a while Step 3 Disconnect the power Login You can login or log off the NVR system Once logged off you cannot do any other operation except changing the multi screen display 10 NVR User Manual User Name admin Password Cancel Fig 3 1 Login Notice The default user name and password is admin and 123456 For complete operational steps for changing password adding or deleting user please refer to section 5 7 User management Configuration 3 3 Live preview re Manual record Motion detection record Sensor Alarm record Schedule record 3 4 Live playback Click Play gt button to playback the record Refer to Figure 3 3 You can do complete operation by clicking the buttons on screen 11 NVR User Manual Camera Name 03 21 2013 15 00 00 Fig 3 3 Live Playback 12 NVR User Manual 4 Add IP Cameras This chapter mainly introduces how to connect multiple IP cameras through NVR Once you finish adding IP cameras you can see the live images through the monitor of the NVR For 16 CH NVR you just need to directly connect the IP cameras to the device through PoE network ports The live images will display after you connect successfully Of course 1f there are free channels you c
13. click certain item to playback File Management Step 1 Enter into Search gt File management Refer to Fig 8 7 Step 2 Select highlighted date and channels Step 3 Click Search button to search the recorded files 49 H NVR User Manual Start time 2010 01 09 00 01 07 2010 01 09 00 02 16 2010 01 09 00 03 28 2010 01 09 01 24 11 2010 01 09 00 08 36 2010 01 09 00 10 10 2010 01 09 00 09 31 T J 2010 01 09 00 10 58 2010 01 09 00 11 30 2010 01 09 00 14 48 2010 01 09 00 12 15 2010 01 09 00 15 43 2010 01 09 00 15 45 2010 01 09 00 17 09 2010 01 09 01 24 11 2010 01 09 02 46 11 2010 01 09 02 46 11 2010 01 09 03 19 45 2010 01 09 17 39 52 2010 01 09 00 01 07 2010 01 09 17 57 12 2010 01 09 00 01 53 2010 01 09 00 02 18 2010 01 09 00 03 01 2010 01 09 00 03 01 2010 01 09 00 03 32 2010 01 09 00 04 12 2010 01 09 00 54 27 2010 01 09 00 14 22 _ 2010 01 09 00 21 54 2010 01 09 00 15 03 2010 01 09 00 22 35 2010 01 09 00 23 51 2010 01 09 00 24 33 2010 01 09 00 25 12 2010 01 09 00 26 57 2010 01 09 00 25 54 2010 01 09 00 28 43 oco0200000000080000003 NIN NININININ NIN Bele LB lel RE Rl elle 2010 01 09 00 31 48 au None inverse 0 0 2010 01 09 00 32 30 GORE mac Fig 8 7 File Management Interface motion 2010 w Jan 9 Sun Mon Tue Wed Thu Fri Sat 1 2
14. device where the backup files are saved in the USB port of PC If your files are saved in DVR format you must have already downloaded the backup player box before doing backup Then double click to open your USB disk to find your backup files k fe and backup player Double click 22 icon to install backup player After you install it open this player and click Open Path button to open your backup file Next click play button to play the backup file Double click the image and then right click to enable audio If you save your backup files in AVI format you can directly open your file by using the media player which supports this format F Super Player HEE 3 po ae Pat pen a li ae pal EE AAA D mars A NA DLA A TH E Super Player IEE Pis War Piy Grada Hal n lt gt ms 4 ey 7 Search 009 009 m BOO Ti le SU AL Tabi JUDO DARA ae 3 ACA A A a A e Resch 202003241 SS 2 lt S6 NVR User Manual Appendix B Calculate Recording Capacity You can calculate the size of hard disk according to the storage time and NVR recording settings The formula is as follows in full frame rate condition Used space per hour MB h Bitrate kbps 8 x 3600 1024 The below are the details at different settings pm m oo o om 2025 1080P 15fps NTSC o om os o a w ee a AE 1800 720P 30fps NTSC _3 w The calculation
15. includes five submenus System Event Log Network and Online users The sub menu list and the options in every menu are similar to that of the NVR Please refer to system information for more details 51 NVR User Manual User Name Tre P Address 2012 03 27 10 54 34 192 168 0 1 2012 03 27 10 52 45 192 16801 2012 03 27 10 52 48 192 168 0 1 2012 03 27 10 52 38 192 168 0 1 2032 03 27 10 39 05 192 168 0 1 2012 03 27 10 34 44 192 168 0 1 2012 03 27 10 21 47 192 168 0 1 2012 03 27 09 52 37 192 168 0 1 2012 03 27 09 51 55 192 168 0 1 2032 03 27 09 49 38 127 0 0 1 2012 03 27 00 12 12 192 168 20 205 2012 03 27 00 12 11 192 168 290 203 2082 03 27 00 12 11 192 168 20 201 2012 03 27 00 12 11 192 168 20 215 2012 03 27 00 12 11 192 168 20 215 Fig 8 10 Remote Information Search mn aimn bimn aimn aimn lamna ame system rem mtem system system Start Time 20120327 B 09 00 20120327 E 23 59 Note There may be slight differences with respect to functions of remote surveillance between through IE and through Apple PC Here we only take IE remote access for example 52 NVR User Manual AppendixA FAQ Q1 Why can t the NVR turn on even after connecting to the power a The power adapter could have gone bad Please change a new power adapter b The power from the adapter may be not enough for operat
16. of the router or virtual server Configure the firewall to allow accessing the NVR Note Port forwarding settings may be different in different routers and server Please refer to the router s manual for details Step 3 Open IE browser input IP address or dynamic domain name and enter If HTTP port is not 80 add the port number after IP address or domain name Step 4 IE will download ActiveX automatically Then a window pops up and asks for user name and password Input name and password correctly and enter to view Note If you cannot download and install ActiveX please refer to FAQ Q8 2 Connect the NVR to internet through PPPoE directly Step 1 Enter into the NVR s Main Menu gt Setup gt Network interface to enable PPPoE and then input user name and password received from your ISP Next click Apply The NVR will connect to the server and would give a confirmation message 42 NVR User Manual Step 2 When accessing the remote interface of NVR user can input WAN IP to access directly user can enter into Main menu Information gt Network interface to check IP address Step 3 If users want to utilize dynamic domain name please apply for a domain name in a DNS server supported by the NVR or router Then add to the NVR Step 4 The following setting steps are as the same as Step3 and Step 4 in Point 1 8 2 Remote Surveillance through Apple PC Note Because the current plug in version of client end just only sup
17. power To record manually 0 9 Digital Input number or choose camera Button mete ee To control PTZ camera Move camera zoom IRIS Focus Clear Button Fn2 Button Get information about NVR like firmware version HDD Info Button information To control playback Play Pause Stop Previous Section Next Section Rewind Fast Forward Snap Button Search Button Cut Button Backup Button Zoom Button PIP Button Fig 2 2 Remote Controller Note You shall press P T Z button to enter PTZ setting mode choose a channel and press PTZ button again to hide the P T Z control panel Then you can press preset cruise track wiper or light button to enable the relevant function Key points to check in case the remote doesn t work 1 Check batteries polarity 2 Check the remaining charge in the batteries 3 Check IR controller sensor for any masking 4 Check the ID of the remote with respect to the NVR If it still doesn t work please try using a good known remote or contact your dealer NVR User Manual Operation processes with remote controller to control multi NVR The default device ID of the NVR is 0 It s not necessary to reset the device ID when a remote 1s to be used to control a single NVR However when controlling multiple NVRs with multiple remote controllers you would need to configure the device ID please refer to below steps Activate remote controller to control the NVR Turn the IR sensor of the remote co
18. set up Email Step 1 Enter into Menu gt Setup gt Network gt Email tab Refer to Fig 5 24 NETWORK Network ral Server Other Settings SMTP Server Fort Sol Check Send Address Password Racen e Address Receive Address Receive Address3 xt Tes Default Fig 5 24 Network Configuration Email Step 2 Set SMTP Server and port SMTP Server Port The name and port number of SMTP server You can setup SSL check such as Gmail according to actual needs Step 3 Set sender s address and password Step 4 Set receiver s email address and click Test button to test the validity of the mailbox 5 6 3 Server This function is mainly used for connecting ECMS NVMS The setting steps are as follows Step 1 In the server interface select Enable as shown in the Fig 5 25 Step 2 Check the IP address and port of the transfer media server in the ECMS NVMS The default server port for auto report is 2009 If it is modified please enter into the transfer media interface to check Step 3 Enable the auto report in the ECMS NVMS when adding a new device Then self define device ID and input the remaining information of the device in the ECMS NVMS Step 4 Input the above mentioned server IP server port and device ID in the server interface Then click Apply button to save the setting Now the ECMS NVMS system will automatically connect this device 30 NVR User Manual NETWORK Network Email VET Othe
19. to another provided that the NVRs are of the same model and that the HDD being migrated would be used as the sole disk in the new NVR However in cases where the new NVR already contains a HDD the migrated disk being installed would have to be formatted In general migrating disks from one NVR to another is not recommended Q12 What is the minimum configuration required for remote monitoring ATIRADEON 7500 X300 Windows 2000 SP4 above Windows XP SP2 above VISTA Q13 How to handle the situation that the codec Control is blocked when downloading in the VISTA or Win7 system This problem can be fixed in two ways a Enter Control Panel gt User Account and Family Safety gt User Account Control refer to Fig 13 1 click Turn User Account on or off Cancel Use User Account Control UAC to help protect your computer b Right click IE browser refer to Fig 13 2 select Run as administrator to run browser Open Open file location Run as administrator Restore previous versions SOX Send To gt Th Turn on User Account Control UAC to make your computer more secure Copy User Account Control UAC can help prevent unauthorized changes to your computer We Crea E YEA recommend that you leave UAC turned on to help protect your computer T Use User Account Control UAC to help protect your computer Delete Rename Properties Fig 13 1 Fig 13 2 Q14 How to play the backup file 55 NVR User Manual Insert your USB
20. 01 24 11 2010 01 09 00 09 31 2010 01 09 00 08 36 2010 01 09 00 10 10 2010 01 09 00 11 30 2010 01 09 00 14 48 2010 01 09 00 10 58 2010 01 09 00 12 15 2010 01 09 00 15 43 motion motion motion 2010 01 09 00 15 45 2010 01 09 02 46 11 2010 01 09 00 17 09 2010 01 09 02 46 11 2010 01 09 03 19 45 motion manual manual 2010 01 09 17 39 52 2010 01 09 17 57 12 2010 01 09 00 01 07 2010 01 09 00 02 18 2010 01 09 00 01 53 2010 01 09 00 03 01 manual motion motion 2010 01 09 00 03 01 2010 01 09 00 14 22 2010 01 09 00 04 12 2010 01 09 00 54 27 2010 01 09 00 15 03 motion manual motion 2010 01 09 00 21 54 2010 01 09 00 23 51 2010 01 09 00 25 12 2010 01 09 00 22 35 2010 01 09 00 24 33 2010 01 09 00 25 54 motion motion motion 2010 01 09 00 26 57 2010 01 09 00 28 43 v Jan Sun Mon Tue Wed Thu Fri Sat 4 1 2 ES E EA ACA N 31 E gt 3 B 10 11 EPJ 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Mi M2 M3 M4 Ms Me M7 Ms M Mo Mio Miu M12 M Mia Mi Mis Mis motion E 2010 01 09 00 32 30 motion i LL JL eu Motion Sensor 2 2010 01 09 00 31 48 Fig 8 6 Event Search Interface Step 2 Click the highlight date and select record channels Step 3 Checkmark the event type motion and sensor Step 4 The events will be displayed in the event list box by clicking Search button Step 5 Double
21. 450011000528 A0
22. Appendix A FAQ 53 Appendix B Calculate Recording Capacity ccccccccccccccccccccccccccccccccccccccccccccccccccecccccccocccceuee 57 Appendix C Compatible Devices iccoccoc cononacacinododocononanaconadan nanonana cin 58 Appendix D 16 CH Specifications ccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccceoeeooooooocecvvee 59 Appendix E 24 CH Specifications cin ear debe d debe 60 1 1 1 1 2 NVR User Manual Introduction NVR Introduction This series of devices are standard 16 24 CH real time 1080P 720P D1 high resolution PoE NVR which adopt the most advanced SOC technique to ensure high definition recording in each channel and realize outstanding robustness of the system The series of product integrates 16 PoE network ports supporting 16 CH IPC direct connection to NVR simultaneous 4 CH playback and HDMI 1080 P high resolution display All of these features make the device meet different security requirements of home financial commerce enterprise transportation and government etc Main Features COMPRESSION FORMAT o Standard H 264 compression with low bit rate and better image quality LIVE SURVEILLANCE o Support HDMI VGA output o 16 CH NVR supports 16 CH 1080P 15fps or 8 CH 1080P 30 fps or 16 CH 720P 30fps IP video input o 24 CH NVR supports 24 CH 1080P 15fps or 16 CH 1080P 30 fps or 24 CH 720P 30fps IP video input o Support channel security by hiding live display e Display the loc
23. NVR User Manual 8 Remote Surveillance 8 1 IE Remote Surveillance In order to view the NVR from a network 1t must be connected to a LAN WAN or internet The network setup should be done accordingly Please refer to 5 6 Network Setup This NVR supports IE browser on Windows XP and Vista platform 8 1 1 On LAN Step 1 Enter into the NVR s Main Menu gt Setup gt Network tab to input IP address Subnet Mask etc If using DHCP please enable DHCP in both the NVR and the router Step 2 Enter Record Setup to set network video parameters like resolution frame rate etc Step 3 Open IE on a computer on the same network Input the IP address of the NVR in IE address bar and press enter Step 4 IE will download ActiveX component automatically Enter the username and password in the subsequent window Notice If HTTP port is not 80 other number instead need add the port number after IP address For example set HTTP port as 82 need input IP address like 192 168 0 25 82 User name and password here are the same with that used on the NVR The default is admin and 123456 8 1 2 On WAN There are two ways for the NVR to connect to internet 1 Connect the NVR to internet through router or virtual server Step 1 Enter into the NVR s Main Menu gt Setup gt Network interface to input IP address Subnet Mask etc If using DHCP please enable DHCP in both the NVR and router Step 2 Forward IP address and port number in Virtual Server setup
24. NVR User Manual For H 264 16 24 channel network video recorder All rights reserved CAUTION Please read this user manual carefully to ensure that you can use the device correctly and safely e There may be several technically incorrect places or printing errors in this manual The updates will be added into the new version of this manual The contents of this manual are subject to change without notice This device should be operated only from the type of power source indicated on the marking label The voltage of the power must be verified before using the same Kindly remove the cables from the power source if the device is not to be used for a long period of time Do not install this device near any heat sources such as radiators heat registers stoves or other devices that produce heat Do not install this device near water Clean only with a dry cloth Do not block any ventilation openings and ensure proper ventilation around the machine e Do not power off the NVR at normal recording condition The correct operation to shut down the NVR is to first stop recording and then use shut down button from the menu and finally switch off the main power e This machine is for indoor use only Do not expose the machine in rain or moist environment In case any solid or liquid get inside the machine s case please turn off the device immediately and get it checked by a qualified technician e Do not try to repair the de
25. O a 14 Download signed ActiveX controls lt J Disable Intemet Local intranet Trusted sites Restricted Enable sites Prompt 14 Download unsigned Activex controls Internet i S ER This zone contains all Web sites you Disable Y haven t placed in other zones Prompt 14 Initialize and script ActiveX controls mot marked as safe Security level for this zone Disable Custom Enable Custom settings To change the settings click Custom Level To use the recommended settings click Default Level Reset custom settings Fig 8 1 Fig 8 2 Q9 NVR displays please wait all the time Why and how can I do a HDD power cable and data cable may not be well connected Please check the connections for HDD b It is also possible that the NVR was forced to stop because HDD has a bad sector and it may have caused the system to halt Check with a good known HDD or try formatting the existing HDD Q10 How to input password and numbers in the interface Click the password or the input box to pop up a small keyboard Please select characters to be input the initial password is 123456 or you can use the digital keys on the front panel or the 54 NVR User Manual digital keys on the remote controller Q11 A hard disk is being identified as a new device however it was being used with another NVR of same model Should it be formatted prior to use It is possible to migrate an HDD from one NVR
26. Schedule for details Note The default schedule of sensor based recording is 24 7 If you want to activate sensor based recording you must enable sensor alarm and setup schedule for sensor alarm see Chapter 5 5 1 Sensor Alarm for more details 24 NVR User Manual 5 5 Alarm Configuration Alarm configuration includes four sub menus sensor motion other alarm and alarm out 5 5 1 Sensor Alarm Sensor includes three sub menus basic alarm handling and schedule Operate the following steps to configure sensor alarm Step 1 Enter into Menu gt Setup gt Alarm gt Sensor gt Basic tab Refer to Fig 5 16 SENSOR MS Alarm Handing Schedule KEH Enable pe Name a NO SENSOR NO SENSOR 2 NO SI Er t NO gt SENSOR NO i El Meat i T NSOQ RF G Default Fig 5 16 Alarm Configuration Sensor Sensor Step 2 Enable channels by checking the checkboxes beside the desired channels Step 3 Set the alarm type according to triggered alarm type Two option NO and NC Step 4 Click Apply button to save the setting Step 5 Enter into Alarm Handling tab Refer to Fig 5 17 Select hold time and then click Setting button to pop up a dialog box as shown in Fig 5 18 SENSOR asia Vilar Handling Schedule Holding Limes rigger io F seting ho S 10 Sell 1 1 u c ESCRIA E 10 r SE E 1 Setting Fig 5 17 Alarm Configuration Sensor Alarm Handling Step 6 Enter into alarm tab to select the opti
27. Step 2 Create domain name You must create 2 domain name to continue h a z 0 9 Cannot end or start Search by Domain NAME STATUS DOMAIN 654321ABC 65432 1abc dvrdydns com Last Update Not yet updated IP Address 210 21 229 138 gt NVR Setting Connect NVR to the Network Client Step 1 Enter into Main menu gt Network gt Other Settings checkmark DDNS select dvrdydns at the DDNS Sever pull down list box and input user name and password Step 2 Enter into configuration interface of the router to map the server port and IP address Click Save button to save the setting Step 3 Login IE browser and input registered domain name http www xxx dvrdydns com connect to NVR client You can also quickly register the domain name in this interface Step 1 Set the IP address manually in the network tab and then click Other Settings tab Step 2 Check DDNS Step 3 Select www autoddns com in DDNS Type column as shown above Step 4 Enter the host name at random like 123 Step 5 Click Register to register the domain name When the successful prompt pops up it means you successfully register your domain name 32 NVR User Manual NETWORK Network Email Server ther Senge DONS pr DONS Type WWW autoddns com Host Domain aulodans com Default If your IP address is not WAN IP address you should forward your IP address and port in your router Then you ca
28. VR User Manual About This Mac Software Update Mac S X Software Stem Preferences T Dock P Recent Items lb Force Quit Finder Sita Sleep TRA Restart Shut Down Log Chut coodeo TEU Step 2 Enter into Network interface and then click Ethernet Connected to check the internet connection of Apple PC Status Connected Ethernet ia currently active and has the IP address XXX EXE XXX XXX Configure iPva Manually IP Address XXX XXX XXX XXX Subnet Mask XXX XXX XXX XXX Router XXX XXX XXX XXX DNS Server MAX XXX XXX XXX Search Domains Advanced LEJ her changes Assis me Step 3 After acquiring the IP address Subnet Mask and so on please enter into the NVR s Main Menu gt Setup gt Network interface to manually input IP address Subnet Mask and Gateway according to the configuration of PC The network segment should be the same as the PC If using DHCP please enable DHCP in the NVR and router Step 4 After finishing the above information users can enter LAN IP and http port in the Safari browser For example input http 192 168 1 100 81 here 192 168 1 100 is LAN IP of NVR 81 is the http port of NVR Click button the browser will download Active X control as shown below ann Wb Client gt gt ajo Ole il esz 01 163 168 1 100281 ga G wLa C M as O ia lc please click kon to load and install Web kitPlug n please restart browser to ensure WebkitPhigin ca
29. al record state and basic information o Support USB to make full control RECORD MEDIA o Support eight SATA HDDs to record for a longer time without any limitation BACKUP o Support USB 2 0 devices to backup o Support built in SATA DVD writer to backup o Support saving recorded files with AVI standard format to a remote computer through internet RECORD PLAYBACK Record modes Manual Schedule Motion detection and Sensor alarm recording Support recycle after HDD full Support 1080P 720P D1 recording Resolution frame rate and picture quality are adjustable Three record search mode time search event search and image search Support 4 screen playback simultaneously Support deleting and locking the recorded files one by one Support remote playback in Network Client through LAN or internet NVR User Manual ALARM Support 16 CH alarm input and 4 generic output Support schedule for motion detection and sensor alarm Support pre recording and post recording Support linked channels recording once motion or alarm triggered on certain channel SECURITY o Customize user right log search system setup two way audio file management disk management remote login live view manual record and playback o Support 1 administrator and 63 users o Support event log recording and checking NETWORK o Support TCP IP DHCP PPPoE DDNS protocol o Support IE browser to do remote view o Support client connection amount setup o Supp
30. an connect the IPC via WAN LAN network For 24 CH NVR you may connect the previous 16 CH directly to the device through PoE network ports and then add the IP cameras for the remaining channels into the NVR via WAN LAN Here we will introduce how to add cameras through WAN LAN To add IP cameras via LAN Step 1 Please enter Menu ZIP Camera tab Refer to Fig 4 1 Click Search button to search the devices in the same network DEVICE MANAGEMENT Deyi e NebAadd ess Manulactur er Product Model Status 137 168 1 7 Distannecte 192 168 1 3 Dikconnee 192 168 1 4 Disconnected 192 168 1 5 Bisconnecter 187 168 1 6 Disconnecter 182 168 1 7 Disconnec 192 168 1 8 Disconnec 192 68 1 9 Disconnec Ss iNi Delete Fig 4 1 Device Management Step 2 Enter into the search tab Click Refresh to refresh the searched devices You can modify the IP address of the searched device by checking the device and clicking Setup button ADD DEVICE Manufacturer Product Mod Addre Fig 4 2 Search Devices 13 NVR User Manual Note If the network of IP cameras and NVR are in LAN their IP address must be in the same network segment For example If the IP address of NVR is 192 168 013 057 the IP address of IP camera must be 192 168 013 XXX Step 3 Choose the searched devices and click OK button to add these devices The added cameras will be listed in the device management interface Step 4 Choose the camera dev
31. ch System Seip hut n o Way Audio Fie Managermen Disk Manageme Remote Login Manual Record R i Playback Fig 5 29 Add User Authority To delete user Step 1 Enter into Menu gt Setup gt Users interface Step 2 Select the added user you want to delete and then click Delete button To modify user Step 1 Enter into Menu gt Setup gt Users interface Step 2 Select the added user you want to modify and then click Modify button to do the 34 5 8 NVR User Manual relevant operation To change user password Step 1 Enter into Menu gt Setup gt Users interface Step 2 Select the added user you want to change its password and then click Change Password button Advanced Advanced configuration includes three submenus reset import export and Block Allow list 5 8 1 Reset Reset all settings the device will reboot 5 8 2 Import Export User can export the data files into mobile storage devices as backup function and then import specified data files from mobile storage device to NVR 5 8 3 Block Allow List GLO Ky ALLOW LIST Block List Allows List 1P From To Las 168 O00 007 lise 168 000 004 ooo 000 000 000 fine 000 000 000 000 000 000 000 lona 006 Ooo 000 000 000 000 0000 000 000 000 000 O00 000 Ono DODO DOO 000 000 000 AJA 00 000 000 000 000 ooo OF 000 000 000 000 ooo 071 OOD 000 000 000 000 000 00 000 Q opa 000 OOo
32. chedule and buzzer To set up alarm out Step 1 Enter into Menu gt Setup gt Alarm Out Refer to Fig 5 22 ALARM OUT Moot Schedule Buzzer Holding Time S 10 Du Ch ALARM CUT 4 Lo Fig 5 22 System Configuration Alarm Out Step 2 Input relay name and select hold time Step 3 Enter into Schedule tab This will go into schedule setup interface The setting steps 28 NVR User Manual for schedule for alarm out are similar to normal schedule setup see Chapter 5 4 1 for details This step 1s very important for alarm out Even 1f you have enabled alarm out in the motion based alarm or sensor based alarm you will not see the result of alarm out if no schedule is added here To set up buzzer Step 1 Enter into Menu gt Setup gt Alarm Out T Buzzer Step 2 Checkmark Buzzer and set buzzer alarm hold time This would trigger the buzzer when the system 1s on an alarm 5 6 Network Configuration Network configuration includes four submenus network Email server and other settings Network settings must be configured if NVR is used for monitoring over network 5 6 1 Network To set up network Step 1 Enter into Menu gt Setup gt Network gt Network tab Refer to Fig 5 23 NETWORK NeTWork Emall Server Other Settings HTTP Port 80 Server Port 6026 Obtain an IP address automatically IP Address 192 168 013 057 Subnet Mask aoa 000 000 000 Gateway 192 168 013 001 Preterred ONS Server 192 182 011 001
33. creen Mode You can choose a screen display mode to show the live images PIP Click this button to set PIP Click this button to choose the bigger picture and then click the little PIP button beside the word None to set the smaller picture After that you can see a picture in picture Dwell Dwell means to display live images from different cameras in a sequence The images may be displayed as a single channel or in a grid fashion from different cameras Dwell mode is enabled only when the chosen display mode is not able to display all the available cameras Color If this button is enabled you can adjust the color of live images E Zoom Single channel large screen electronic amplification Audio Enable sound PTZ Click the PTZ button to control rotation position speed and auto scan of the PTZ connected to the IP camera Record Click this button to start stop recording Playback Click this button to playback the recorded files You can click Move Tool button and drag it anywhere with the left mouse to move the main menu bar anywhere Click Main Menu button to pop up a window as Fig 5 2 you can also press MENU button on the front panel or operate with remote controller to display the main menu Clicking Setup icon will pop up the configuration menu MAIN MENU ill Information Pl y a Manual Alarm Disk Management Upgrade IP Camera kK Logon Shut Down Fig 5 2 Main Menu 15 NVR User Manual Alarm Neba
34. date and channels on the right hand side A data with highlighted borderline indicates presence of data Step 3 Checkmark Motion Sensor or All accordingly Step 4 Click Search button to display the searched event information in the event list box Step 5 Double check a certain record file to playback 36 NVR User Manual SEARCH Fig 6 2 Search Configuration Event Search 6 3 File Management Step 1 Enter into Menu gt D Search gt File Management interface Refer to Fig 6 3 SEARCH Time Search Fig 6 3 Search Configuration File Management Step 2 Select date and channels The date with highlighted borderline indicates presence of data Step 3 Click Search button to display the searched files in the file list box Step 4 Use All button to lock unlock or delete all files in the file management column Step 5 Double click an unlocked item to play Lock Select a file and click Lock button to lock this file after that that file will not be deleted or covered Unlock Select a locked file and click Lock button to unlock this file Delete Select an unlocked file and click Delete button to delete this file 37 NVR User Manual 6 4 Search by Image Step 1 Enter into Menu gt Search gt Image tab Step 2 Select data and channels on the right hand side Step 3 Press Search button to search for a recorded image Step 4 Once an alarm image has been identified the user can double click
35. e max 25fps PAL 30fps Sub stream NTSC for every channel but it needs higher network bandwidth second stream has low frame rate max 6fps ii PAL 7fps NTSC for every channel but it requires low Full Screen network bandwidth as compared to the master stream zoom in Therefore users can select the stream according to their bandwidth Fig 8 2 Right Key Sub Menu All to sub stream Set all channel to master stream or sub stream Enable audio Enable or disenable audio Full screen The live preview picture will display in full screen and the tool bar will be hidden double click left or click right mouse to return Zoom in Single channel large screen electronic amplification Click the channel which needs to be zoomed Right click to select zoom in button to zoom in the image Double click or right click to exit 8 4 Remote Playback amp Backup 8 4 1 Remote Playback Click 2 button to enter into record playback interface Refer to Fig 8 3 Select the record date and channels and double click the file name in the record file list box Then user can play that file and preview the picture 47 NVR User Manual SES Record Date 2009 1224 a a V 00 00 00 00 00 00 CAM1 CAM2 CAM3 CAM4 v File Name dan Lenc 20091224001802_01 avi 00 18 02 20091224063015_03 avi 06 30 15 20091224062529_04 avi 06 25 29 235 20091224062750_02 avi 06 27 50 al o 2009 8209 151 i 20031224062529 09
36. e network setups are the same as step one of point 2 on WAN of IE remote surveillance Step 2 Enter WAN IP and http port or domain name in the Safari browser to install the Active control Then a window pops up and asks for user name and password Input name and password correctly and enter to view 8 3 Remote Preview i H Master Stream i H Sub stream H 345678 9 10 11 12 13 14 1516 LADA A 38 Z B 9 10 11 12 13 14 15 16 1 2 3 4 5 Fig 8 1 Remote Live Preview Symbol and function Definitions 45 NVR User Manual Channel indicator Screen display mode Start IE record 6 Start recording Start talking 8 Playback 9 Color PTZ control I Master sub stream status ff O e Note Click ca button to record manual and the record file will be saved in user s PC Screen display mode Snap pictures The system will automatically capture pictures and save those pictures in the computer by E User should set up the path for those pictures in the Configuration gt Local configuration clicking Snap icon Color adjustment Drag the slide bar to adjust Brightness Contrast Hue and Saturation Click Default to reset them to original value amp o My Drag the scroll bar to adjust the saturation of channel ___ Q Click this button to recover the default value of brightness contrast saturation and hue Save the adjustment PTZ control Please connect speed dome to
37. ea NVR User Manual Fig 2 3 Digital Numbers and Letters Input Window In Playback Click to choose the options Right click to return to live mode In Backup Click to choose the options Right click to return to previous picture In PTZ Control Click left button to choose the buttons to control the PTZ Click right button to return to live Note Mouse is the default tool for all operations unless an exception as indicated 3 3 1 NVR User Manual Basic Function Instruction Startup and Shutdown Please make sure all the connections are done properly before you power on the unit Proper startup and shutdown are crucial to expanding the life of your NVR 3 1 1 Startup Step 1 Connect with the source power Step 2 The device will boot and the power LED would turn blue Step 3 A WIZZARD window will pop up and show some information about time zone time setup network configuration record configuration and disk management You can setup here and refer to the concrete setup steps from the corresponding chapters If you don t want to set up Wizard please click Exit button to exit Note The default output is HDMI output Hold and press ESC Exit key to switch the output between VGA and HDMI 3 1 2 Shutdown 3 2 You can shut down the device by using IR remote controller and mouse By IR remote controller Step 1 Press Power button This will bring up a shutdown window The unit will shut down by clicking OK
38. format is Total Recording capacity Used space per hour MB h coverage rate of hard disk x recording time hour xchannel numbers For instance one customer sets resolution to1080P frame rate to 15fps bitrate to 4M and enables total 4 channels He wants the unit to record continuously in a month Below is the calculation Total Recoding capacity 900 mb h X 24 hours day X30 days X4 channels 2592000 MB 2531 25 GB Therefore customers just install tvo SATA HDDs with 1 5TB for one month recording 57 NVR User Manual Appendix C Compatible Devices 1 Compatible USB drive after test 512MB IG 2GB SanDisk 2 Compatible SATA CD DVD writers after test 3 Compatible HDD list 58 NVR User Manual Appendix D 16 CH Specifications ma ss 16 CH 720P 30fps 16 CH D1 30fps 1080P 12801024 1024 768 800 600 RAR o RAR ss NoornciscH OO Pose Manual Sensor Timer Motion detection E RJ45 x1 RJ45 x16 RS485 USB2 0 x 2 one for backup another for USB mouse SATA x 4 DVD RW x 1 or SATA x8 ESATAx2 10 90 59 NVR User Manual Appendix E 24 CH Specifications ma ss 24 CH 720P 30fps 24CH D1 30fps 1080P 1280 1024 1024 768 800 600 RAR o RAR ss NoornciscH OO Pose Manual Sensor Timer Motion detection E RJ45 x1 RJ45 x16 RS485 USB2 0 x 2 one for backup another for USB mouse SATA x 4 DVD RW x 1 or SATA x8 ESATAx2 10 90 60
39. gt Record gt Time interface to set recording time Refer to Fig 5 12 Step 2 Set Pre alarm record time and post alarm record time Select All to set the same settings for all channels Step 3 Click Apply to save the setting 21 NVR User Manual RECORD Enable Record Bitrat Fig 5 12 Record Configuration Time Pre alarm Record Time Set the time in seconds to pre record before the actual recording begins Post alarm Record Time Set the time in seconds to post record after the actual recording has finished five options 10s 15s 20s 30s 60s 120s 180s and 300s Expire Time Set the expiration time for recorded video If the set date 1s overdue the recorded files will be deleted automatically 5 3 4 Stamp This provides an option to enable or disable the Camera Name and the Time stamp on the video The user can also choose a position for the stamp on the screen To set up stamp as follows Step 1 Enter into Menu gt Setup gt Record gt Stamp interface Refer to Fig 5 13 RECORD Enable Record Bitrate Time CH Gamera Name Fimi Fig 5 13 Record Configuration Stamp Step 2 Checkmark camera name and time stamp Click Setting button to set up the position of the stamp You can drag the camera name and time stamp at random positions as shown below Step 3 Select All to set up all channels with the same parameters 22 NVR User Manual G Aa i T varia ii o ii 4 qa ee
40. ice and click Setup button to enable the camera Refer to Fig 4 3 Check the enable checkbox select channel and input the username and password of this device Then click OK to save settings MODIFY DEVIC Enable Channel Manufactun r Product Model IF Address Server Port User Name admir Password Fig 4 3 Add Device To add IP cameras via WAN Step 1 Please enter MenuIP Camera tab Refer to Fig 4 1 Step 2 Click Add button to pop up a window similar to Fig 4 3 You need to check Enable box select channel manufacturer and product model and manually input IP address server port username and password of this device Note If the NVR and the IP cameras you want to add are both in WAN the IP address of the IP camera input here must be WAN IP You should forward the LAN IP address and port of the IP camera in the router and use its WAN IP address provided that the IP camera is in local area network otherwise the NVR cannot connect this IP camera 14 NVR User Manual 5 Main Menu Setup Guide Click right mouse or press ESC Exit button on the front panel to display the main menu toolbar on the bottom of the screen Refer to Fig 5 1 PIP Color Audio Snap Playback b Main Menu Screen Mode Dwell E zoom PTZ Record Move Bhs Ee dij MOM ee se Ow SO ncc Fig 5 1 Main Menu Toolbar Click the E amp icon beside the screen mode to display a channel select dialog S
41. ing the NVR Please use the power adaptor supplied along with the NVR c It could be a hardware problem Q2 There is no menu displayed why a Check whether the monitor is connected to the main video out The monitor might be connected to VGA port whereas the NVR may be set for output through HDMI Long press Exit key to toggle the output modes Q3 The NVR LED turns on however there is no output Why a The power from the adapter may be not enough for operating the NVR Please use the power adaptor supplied along with the NVR b It could be a wiring issue Please check the connection for the same c Check the monitor settings Q4 Why are no images displayed on few or all the channels of the NVR a It could be a wiring issue Please check the cable and the ports of the cameras b The problem can also be related to cameras Please check the same c Please make sure that you have added and enabled the cameras Q5 Why can t I find the HDD a The power from the adapter may be not enough for operating the NVR Please use the power adaptor supplied along with the NVR b It could be a wiring issue Please check the power and data cables of the HDD c The HDD could have gone bad Change a new one Q6 Why is there no video recorded a Make sure the HDD was formatted prior to use b Maybe the user hasn t enabled the record function or has done incorrect setup Please refer to Record Configuration for more details c
42. mera Input number 0 the number above 10 Change direction 7 Change the screen mode Confirm selection To connect external USB device like USB mouse or USB flash 2 3 Rear Panel Instructions NVR User Manual A RE RER 1 CH audio fedme A a RR 6 AlarmOut Relay Output Connect to external alarm Alarm Inputs for connecting sensors Log ESAaTA Connect to external SATA hard drive s 9 Digo Connect to high definition display device VGA port VGA output connect to monitor Network port a spa Connect to external USB devices like USB flash USB HDD for backup or update firmware or connect to USB mouse 13 PoEPorts PoE network ports connect to 16CH IP cameras with PoE function Alarm Out Connection Pull out the green terminal blocks and loosen the screws in the alarm NO out port Then insert the wires of the alarm output devices into the NE port of NO and COM separately Finally tighten the screws Provided that the external alarm output devices need power supply you can connect the power supply as per the following figures 2 4 Remote Controller It uses two AAA size batteries e Open the battery cover of the Remote Controller e Place batteries Please take care of the polarity and e Replace the battery cover The interface of remote controller is shown in Fig 2 2 Remote Controller NVR User Manual Hee A E o I a S55 w Power Switch off to stop NVR Use it before turning off the Button
43. n take effect after install Step 5 Click Y con and then select the Active X control the welcome interface will be shown Click Continue gt Install button the following window will pop up ana ital bol lira Puya 64 E Type your password to allow installer to make my i Welcome to the WebCitentPlugls 64 Installer a a changes 4 Doers lb 9 m brines You will be quided thnogayh the sbepa mmeges4ary to Mame c bdoo gr install Hey or ZAN 0 Derails F H E Cantina _ 7 Cancel o gt 44 NVR User Manual Input the name and password of Apple PC and then click OK to install this Active X control Step 6 After finishing installing the Active X control please quit from the Safari browser Right click Safari icon on the desktop and select Quit button to quit the browser Then restart Safari browser Input the IP address and http port to enter the login interface of NVR 8 2 2 On WAN There are also two ways for NVR to connect to Internet 1 Connect the NVR to internet through router or virtual server Step 1 The network setups are the same as step one to step four of point 1 on WAN of IE remote surveillance Step 2 Enter WAN IP and http port in the Safari browser to install the Active control Then a window pops up and asks for user name and password Input name and password correctly and enter to view 2 Connect the NVR to internet directly Step 1 Th
44. n to test the sensitivity as per the local conditions Once motion is sensed it displays a figure icon Click icon to save the setting Click icon to exit the current interface cab Note Prior to setting motion detection field it is recommended that you click icon to clear the existing field and set afresh Step 6 Select All to set the same settings for all channels Step 7 Click Apply button to save the setting Step 8 Enter into Schedule tab The setting steps for schedule for motion based alarm are similar to normal schedule setup see Chapter 5 4 1 for more details 27 NVR User Manual 5 5 3 Other Alarm This tab gives a choice to configure alarm for Disk Full IP Conflict the Disconnect event etc Step 1 Enter into Menu gt Setup gt Other Alarm Refer to Fig 5 21 OTHER ALARM Alarm Type Disk Full DSE Buzzer IP Conthicl Disconnect Ermail A Disk Attenuation Ta Alarm Out Disk Lost Disk Shorlage Alarm 128 ME Default Fig 5 21 Other Alarm Step 2 Use the dropdown menu and select the event or the alarm Step 3 Check the required trigger options If the selected event is Disk Full then use the drop down box for Disk Shortage Alarm to choose a threshold value for remaining HDD space If the threshold value is reached the system will trigger the Disk Full Alarm Step 4 Click Apply to save the setting 5 5 4 Alarm Out Alarm out includes three sub menus alarm out s
45. n use the domain name plus HTTP port to access your device Website provided by dynamic domain name supplier The optional www dvrdydns com DDNS server www meibu com www dyndns com www autoddns com www no ip com and mintdns type 5 7 User Management Configuration This tab allows you to add normal or advanced users To add user and setup user authority Step 1 Enter into Menu gt Setup gt Users Refer to Fig 5 27 USER MANAGEMENT iser Name BES ype FE MAC Address admir PANI NA LULA LENT LAN CI LALA LALA Fig 5 27 User Management Configuration Step 2 Click Add button to display a dialog box as Fig 5 28 33 NVR User Manual ADO USER al Authority User Name ques Password Confirm Pacsword User Type Normal Binding PE MAC Address PC MAG Address ao oo 00 00 00 Och Fig 5 28 Add General Step 3 In General tab input username password and select user type You can also check Binding PC MAC Address and input this address Step 4 Click OK to save the setting Note When the default value of binding PC MAC Address is 0 the user is not bound with the specified computer If the bind option is used the user would be able to log into the NVR only through the specific computer carrying the MAC address Step 5 Select Authority tab and then assign the operation rights for particular user Refer to Fig 5 29 Step 6 Click OK to save the setting ADD USER General AIRE Log Sear
46. ntroller towards the IR receiver on the front panel press the number key 8 twice on the remote input device ID of the NVR to be controlled Range from 0 65535 the default device ID is 0 and press ENTER to confirm You can check the device ID of a NVR from System Setup gt Basic gt Device ID You can also set multiple NVRs with the same device ID however this can cause interference if the NVRs are kept close to each other 2 5 Control with Mouse 2 5 1 Connect Mouse It supports USB mouse through the ports on the rear panel If mouse is not detected or doesn t work check below steps 1 Make sure the mouse is plugged in the USB mouse port 2 Try with a good known mouse 2 5 2 Use Mouse During live Double click on any camera window to see the full screen Double click again to return to the previous screen Right click to reveal the control menu on the screen Right click again to hide the menu In Configuration Click to enter a particular option Right click to cancel the option or to return to the previous menu In order to input a value in a particular screen move cursor to the input box and click An input window will appear as Fig 2 3 It supports digits alphabets and symbols input Click Shift button to input capital letters and symbols click Shift button again to return It supports mouse drag Take motion detection area setup for example Click customized hold down the left button and drag to set motion detection ar
47. ons to handle alarm 25 NVR User Manual TRIGGER Channel 1 b dar Io Record Buzzer Show Full Screen lo Alarm Oul Emal Fig 5 18 Alarm Handling Trigger Buzzer If selected the local buzzer would be activated on an alarm Show Full Screen If selected there will pop up the chosen channel on the monitor on an alarm trigger To Alarm Out If selected this would trigger external relay output on an alarm Email If selected the NVR will send an email alert to the preconfigured email address in case of a sensor based alarm from the particular input Snap If selected the system will snap images of the checked channels on an alarm and save them in the HDD automatically Step 7 Enter into To Record tab Select recording channels It would be recorded in case of an alarm Click OK button to save the setting Step 8 Enter into Schedule tab The setting steps for schedule for sensor based alarm are similar to normal schedule setup You can refer to 5 4 1 Schedule for details This step is very important for sensor alarm Even if you have enabled the sensor alarm for all channels and setup the trigger you will not see the result of sensor alarm if no schedule is added If you have set schedule for sensor based recording in the same timeline recordings can also be triggered 5 5 2 Motion Alarm Motion includes two sub menus motion and schedule The steps to set motion alarm are as follows Step 1 Enter into Menu gt Setu
48. ork System Setup 5 1 Basic configuration Basic configuration includes three sub menus system date amp time and DST 5 1 1 System Step 1 Enter into Menu gt Setup gt Basic gt System Refer to Fig 5 3 BASIC Prete Date amp Time DST Device Name Device ID Video Format Password Check Show System lime Max Online Users Video Output HD Mi Language English Logout After Minutes Fig 5 3 Basic Configuration Basic Step 2 In this interface you can setup the device name device ID video format max network user VGA resolution and language The definitions for every parameters display as below Device Name The name of the device as it may display on the client end or on CMS this would help the user to recognize the device remotely Device ID This ID is used to map the NVR with IR remote controller and speed dome cameras Video Format Two modes PAL and NTSC User can select the video format according to the cameras being used Password Check If enabled the user would need to input the user name and the password for performing corresponding operations Show System Time If selected displays the current time during live monitoring Max Online Users To set the maximum number of concurrent user logins in the NVR Show wizard If selected the GUI would launch the startup wizard on every boot allowing 16 NVR User Manual user to do basic setup Video Output Resolution of live display interface Lang
49. ort dual stream Network stream is adjustable independently to fit the network bandwidth and environment o Support picture snap and color adjustment in remote live Support remote time and event search and channel playback Support remote full menu setup changing all the NVR parameters remotely Support mobile surveillance by phones with iPhone amp Android OS Support CMS NVMS to manage multi devices on internet NVR User Manual 2 Hardware Installation Check the unit and the accessories after getting the device Please don t power up the unit till the physical installation is complete 2 1 Install Hard Drive amp DVD Writer 2 1 1 Install Hard Drive Notice 1 This series supports two SATA hard drives Please use the hard drive the manufacturers recommend specially for security and safe field 2 Please calculate HDD capacity according to the recording setting Please refer to Appendix B Calculate Recording Capacity Step 1 Loosen the screws to open the case and then loosen the screws in the both sides to take out of the upper mounting bar as shown below Step 2 Put the HDD under the lower mounting bar Then tighten the screws and connect the power and data cables The pictures are shown as follows Step 3 Install other three HDD according to above mentioned method Then cover the upper mounting bar and tighten the screws to fix it Put the HDD under it and tighten the screws with the screwdriver as shown below
50. p gt Alarm gt Motion gt Motion tab Refer to Fig 5 19 Step 2 Enable motion alarm set alarm hold time which refers to the time till which the system will wait for further detection of motion e g If the holding time is set to 10 seconds once the system detects a motion it will go into alarm but would not detect any other motion alarm specific to channel until 10 seconds If there is other motion detected during this period it is considered it as continuous movement otherwise it will be considered as a single motion 26 NVR User Manual MOTION CH I nable Holding Time rigger Ti SENA SHUT 10 Setting Setting 1 Setting Setting F Setting Seating 1 E Setting Setting to Setting Selling Fig 5 19 Alarm Configuration Motion Step 3 The setup steps of motion trigger are similar to Alarm Handling See Chapter 5 5 1 Sensor gt Alarm Handling setting for more details Step 4 After clicking Area button a dialog box will pop up as Fig 5 20 AA ee Fig 5 20 Motion Area Step 5 In the Area interface you can drag slide bar to set the sensitivity value 1 8 The higher the value is the more sensitive it is to motion Since the sensitivity is influenced by color and time day or night you can adjust its value according to the practical conditions Left click the grid and drag to delete area Click icon to set the whole area as detection area Click icon to clear the set detection area Click H ico
51. ports 32 bit mode so the safari browser shall start 32 bit mode If the browser is the earlier MACOS version the default setting is 32 bit mode and the setting can be skipped The Setting steps are as follows First Right click safari icon and select Show in Finder Second Select Applications Right click Safari App Select Get Info C Capa FA ree apo t L magr Capt apo Mowt ae E oro asp Cf rr ie TET 7 Tunia i n lt Open Emirs whig Teuiar r amp Mal spg Show Package Contenti Paun ere 2 Morro More to Trash de i epee Pieper Ch i ie ao apo ME A mtrs Compreis Sami app Aura Sala app to Disc E Pit boed i Pope Af D Dih Duplicate T haa Make Alas 48 inap Quick Look Safari app virkri M faciem Pei Copr Salario Options Remove from Dock poer Show View Options Open at Login E Tene Mach Open Show in Finder Y aaas FT Eg c6 99 Third Select open in 32 bit mode F Ceneral Kind Application Intel Size 7 3 MB on disk 48 525 663 bytes Where Applications Created 2009 8 20 1 22 3 5 Modified 2010 10 19 j 11 56 Version 5 0 2 Copyright O 2003 2010 Apple inc Y Open in 32 bit mode Open using Rosetta gt More info Y Name 6 Extension 8 2 1 On LAN Step 1 After starting Apple computer click Apple icon The following window will pop up Please select System Preferences gt Internet amp Wireless click Network 43 N
52. r S tinas Enable sai Server 192 163 123 Server Port 20049 Device ID 1382 Default Apply Fig 5 25 Network Configuration Server 5 6 4 Other Settings If your NVR is set to use PPPoE as its default network connection you may setup DDNS to be used in connection The setting steps are as follows Step 1 Enable DDNS server Step 2 Select DDNS server Step 3 Enter user name password and host domain name of the registered website Step 4 Click Test button to test the effectiveness of the relevant information Step 5 Click Apply button to save the setting NETWORK f Network Email UE SE DONS coal DONS Server User Name Password Host Domain DONS Update Hours Default Fig 5 26 Network Configuration Other Settings Note The domain name selected by user is a banding domain name of NVR User should logon the website provided by the server supplier to register a user name and password and then apply for a domain name online After the successful application user can access the device from the IE client by inputting that domain name gt Domain name Registration Take www dvrdydns com for example Step 1 Input www dvrdydns com in the IE address bar to visit its website Then click Registration button to register as shown below 31 NVR User Manual HEW USER ALGISTRATION EKAN Pagryniai PR las LETETT Wiii MCN D Wy fes phone number HTWER JE Bubri Rosat
53. rface 23 59 69 Ola M2 Bs Es ales Bs Br Es as Ev Eu Ex alas Es Bis Bss Step 1 Select channels set the start and end time and then click Search button to display the file information in the file list box Step 2 Select backup files and click Browse button to set the path Then click Backup button to start backup The backup files will be saved on user s PC 50 8 6 8 7 NVR User Manual 8 5 Remote System Configuration You can do remote setup of the device which includes functions like basic configuration live configuration record configuration schedule configuration alarm configuration network configuration and user configuration You should select an option from the menu list on the left and then setup the relative parameters Only one user can do configuration setup at a given point of time Click Config tab to enter into the below interface as Fig 8 9 LIVE SEARCH BACKUP CONFIG TOOLS INFO Fig 8 9 Remote System Configuration The sub menu list and the options in every menu are similar to that of the NVR Please refer to Main Menu Setup Guide for more details Tools Click on tool s tab to access the disk management tool You can view the status of the HDD change view the read write properties and can also format the HDD remotely Remote Information The Info tab provides a web based interface to access the general information pertaining to the NVR settings It
54. rmation Check system information includes five submenus system event log network and online user 7 1 1 System Information In this interface user can check the hardware version MCU version kernel version device ID etc 7 1 2 Event Information In this tab you can search for events like motion sensor and video loss The utility provides an interface to have a date based and a channel based search This report can further be saved on a USB flash drive as an html file using the export button 7 1 3 Log Information In this tab you can search for relevant logs as per the set date and event which includes operation setup playback backup search check information and error This report can further be saved on a USB flash drive as an html file using the export button 7 1 4 Network Information In this interface you can check relevant parameters of network 7 1 5 Online Information In this tab you can check the details of the connected online users Refresh refresh the current interface Disconnect Disconnect the online users to access NVR If this function is used by the admin the particular PC will not be able to access the device for five minutes 7 2 Manual Alarm In this interface user can trigger a manual alarm 7 3 Disk Management 1 Format the disk Step 1 Enter into disk management tab Note Please format the hard disk before recording If not formatted it will show the status of the disk free
55. ta RS ESSENS TERE RER EEN 35 53853 Bloc kK Allow ASE ac 35 6 Search Playback amp Bacup sscsecaceccscdvcccccccaceecwadsxavcne cece vcacassascosascs rarosa n oriras iienaa E as ii 36 CL AAA Mie hebr ons ne eet Tene kend abe UE ae 36 PA eee OTST AL tabe Aa St ere eer eee 7 bal 36 REA Gh ala O RS ny ene RRA 36 G3 File Mnane i Cini 25 eerie katte e o a o ie es le ae daa ee 37 G 4 neare h DA e o e ota 38 a AAA A A A A A ee Ore ee Coren Le eer eee 38 E Ma as NV Ria AAA AAA AA 40 Jol Check Sy stein Intormatioh atico orto 40 ARES AAA ened cea nem need e R n enn SEERE RESENS e AO ZE a 40 LZ E Vent nioma 0 e OPERA ONPE POE tre ester cert arte treat aa ena te eres a ee er 40 FLA AN ds 40 7 1 4 Network IntormaO stent 40 Ai AAA N E RE TER SEN SEE 40 SAME vest c tat yeas ted aie rtot ue rami Aeneis re 40 SAD A AAA A A A ee Ae e A nett 40 7 A eek Seater seer ree NN a eer Ae nn enn ere ree 41 LIO OOM Mg te sere A 41 S Remote Surveillance adicionada 42 S VITE Remote Ur EII e 42 A lca e ATA A co leh LAIS c 42 3 12 00 WAR 3222902462032539 ai idad 42 8 2 Remote Surveillance through Apple PE it 43 SL TOPTAN DAO 202220002 09 E 22902007 eler 20200 N 43 A IN 45 8 5 REMOLE Pre VIEW dt tii dia 45 S 4 Remote Playback amp Back ti told 47 SAT Remote Playback id 47 s42 Remote Bac keea 3ir da A At RR BSU KER ERE RENEE RESET E BEES DERE att A 21 RE fas 50 8 5 Remote System CONDUCTA AAA A toerg 51 8 6 Tools 51 NL AA A O II nka aoc RA MA 230 RE 51
56. ted schedule If you want to apply the schedule setting of a certain channel to other or all channels you need to select channel and click Copy button You can also set week schedule by double clicking in the grinding area This will take you to see a dialog box as Fig 5 15 Step 1 Select a day and click Add button to schedule start time and end time Then click to save Step 2 Select other days and add schedule or copy settings from one schedule to the others under the Apply Settings To item SCHEDULE Nednesda Apply Settings To AJI End Time Fig 5 15 Schedule Week Schedule 5 4 2 Motion Schedule This tab allows setting schedule for motion based recording The setting steps are as follows Step 1 Enter into Menu gt Setup gt Schedule Motion tab Step 2 The setup steps for schedule for motion based recording are similar to normal schedule setup You can refer to 5 4 1 Schedule for details Note The default schedule of motion based recording is 24 7 If you want to activate motion based recording you must enable motion alarm and setup schedule for motion alarm see Chapter 5 5 2 Motion Alarm for more details 5 4 3 Sensor Schedule This tab allows setting schedule for sensor based recording The setting steps are as follows Step 1 Enter into Menu gt Setup gt Schedule Sensor interface Step 2 The setup steps for schedule for sensor based recording are similar to normal schedule setup see Chapter 5 4 1
57. the device via RS485 firstly make sure the protocol of the speed dome is supported by the device and set the relative parameters manually User can control the dome up down right left or stop rotating on Control Center adjust rotation speed Iris and zoom focus on the dome and set the presets etc Buttons definition dto rotate the dome upwards Y to rotate the dome diagonally up left to rotate the dome diagonally up right W to rotate the dome downwards f to rotate the dome diagonally down right 4 to rotate the dome diagonally down left ito rotate the dome towards left Bto rotate the dome towards right MI to stop rotating the dome 46 NVR User Manual p f Drag the scroll bar to adjust rotating speed of the dome Iris button Click Bi aion near Iris button to increase light of the dome Click button near Iris button to decrease light of the dome Zoom button Click Mutton near Zoom button to zoom in the locale picture of this camera Click button near Zoom button to zoom out the locale picture of this camera Focus button Click orton near Focus button to have long focus Click button near Focus button to have short focus IO Select and do auto cruise E gt o ee wU Light button Right Key Menu Click the right mouse on the live interface to display a pull down menu as below Stream The NVR supports master stream and sub stream a Master stream has higher frame rat
58. the image to play recording SEARCH ae AS CH 01 0511482013 14 55 11 Fig 6 4 Search Configuration Image 6 5 Backup This unit supports backup by built in SATA DVD Writer with USB Flash You can also make backup by IE browser via internet see section 8 3 2 Remote backup Step 1 Enter into backup configuration Refer to Fig 6 5 Step 2 Set the start amp end time select channels and click Search button to display the searched data in the data backup list box BACKUP La f ae irme Start Timi Wie E 1 1 1 1 1 1 137714 1 1 1 1 1 1 1 1 Fig 6 5 Backup Configuration 38 NVR User Manual Step 3 Select a required file or checkmark All to select all data files Click Backup button to display Backup information window BACKUP INFORMATION tart Time 02 04 2014 00 00 00 End Tirm 03 04 7011 73 59 59 The Number OF Files B dize 68 1 00 rage Media USB 1 Free GE 1 000 Backup Player sal Save File Type vik Step 4 In the backup information interface you can check the relevant information of backup files storage type save file type etc Then click Start button to start backup Note If the backup files are saved in DVR format please check backup player Only this player can play these files in DVR format If the backup files are saved in AVI format you can play these files with common media player 39 NVR User Manual 7 Manage NVR 7 1 Check System Info
59. the setting 5 2 Live Configuration Live configuration includes three submenus live main monitor and mask 5 2 1 Live In this interface you can set up camera name To set up camera name Step 1 Enter into Menu gt Setup gt Live Refer to Fig 5 6 LIVE Main Monitor Mask Al Camera Name Setting Setting Setting Servo Setting Setind Recording Status Fig 5 6 Live Configuration gt Live Step 2 A software keyboard will pop up by clicking camera name area Click the letters and or digital numbers on the keyboard to input the name you want to display in live image Step 3 Checkmark the camera name in the show name area All channels will show the camera name by checking All checkbox To set up color Step 1 Click Setting button for a particular camera channel to see a window as below NVR User Manual Step 2 In this interface you can adjust brightness hue saturation and contrast in live Click OK button to save the setting 5 2 2 Main Monitor The main monitor settings allow you to set camera sequence in live display mode Operate the following steps to set main monitor Step 1 Enter into Menu gt Setup gt Live gt Main Monitor interface Refer to Fig 5 7 Step 2 Select display mode and channel Step 3 Select dwell time Click Kil button to set up the previous channel groups of dwell picture Click wl button to set the latter channel groups of dwell picture Step 4 Click
60. uage To set up the menu language Note After changing the language and video output the device needs to login again Logout After Minutes You can setup the screen interval time 30s 60s 180s 300s If there is no any operation within the setting period the device will auto logout and return to the login interface No Image When Logout If selected there will be no image showing when logout 5 1 2 Date amp Time Step 1 Enter into Menu gt Setup gt Basic gt Date amp Time tab Refer to Fig 5 4 BASIC System ate k fin Date Formal Um MDD YY lime Format ad Hour lime one GMI Sync Time With NTP Server NTP Server time Wire aS COM System Date O87 157 2013 System Time Default Fig 5 4 Basic Configuration Date amp Time Step 2 Set the date format time format time zone in this interface checkmark Sync time with NTP server to refresh NTP server date You can adjust system date manually Step 3 Click Apply button to save the settings 5 1 3 DST Step 1 Enter into Menu Setup Basic DST interface Refer to Fig 5 5 BASIC System Date amp Time ET Daylight Saving Time Time Offset Hours i Mode O Week From January ritil January The tsi i Default Fig 5 5 Basic Configuration DST 17 NVR User Manual Step 2 In this interface enable daylight saving time time offset mode start amp end month week date etc Step 3 Click Apply button to save
61. vice by yourself without technical aid or approval e When this product is in use the relevant contents of Microsoft Apple and Google will be involved in The pictures and screenshots in this manual are only used to explain the usage of our product The ownerships of trademarks logos and other intellectual properties related to Microsoft Apple and Google shall belong to the above mentioned companies e This manual is suitable for 16 24 channel network video recorders All examples and pictures used in the manual are from 16 channel NVR Contents E Introduccion a ici 1 2 INE RTO MC THOT aserne derne anes R EA saa civeacs a cari 1 1 2 Main Features A 8404 0AL0 O E CARL DCA E ERE EET FE FEE TEENS ees 1 2 Hardware Tris Catena asa AA A AA cidad 3 241 Install Hard Drive amp DVD Witt A e E e 3 2 41 21 Install ATA DAS aaa 3 2 tal DY DWIE z recs 092234 ELERS ASA PA UST A EOE A DE AA L 4 2 2 ETORRI ee bs e ea 5 LA AA A TO 5 24 Remote CO iaa 6 ZE OOO WA NOUS SS RSS AS A ESTER 8 FILC 97 a un as en ER MOUS 2222226400252361 220 22200200 ete eA Aid CC e RENSE ENE n 8 2 52 WS MOUS aene E d SE A ca 8 3 Basic Function Instruction vccsisesessccesvetseceisecdsecscecladeusatacantdalendeccedecendactadescasecesteaterdaecaiercossedeeses 10 SL Startup and Ut WD AAA 10 PR LR A 9 A E E ON AN Tn RAD 224 A EA ERE DE 2A ESSA AR OA Te 10 3 2 eS NUCL OWN CONPOPOAC CN nn NO 10 Be iMag E ET RER Sans ent A DENE FE RE SENE 10 L VE PLE VIEW AAA AAA AAA A e e 11

view User`s Manual in format - COP

Contents

Download Pdf Manuals

Related Search

Related Contents