Home

18.5` EB1927WSL_User Manual

image

Contents

1. Figure 1 Installing and Removing the Base POWER SOURCE 1 Make sure that the power cord is the correct type required in your area 2 This LCD monitor allows operation in 100 240V AC voltage area No user adjustment is required 3 Connect the AC power cord into your LCD monitor s AC power input The AC power cord may be connected to either a wall power outlet or the power outlet socket on your PC depending on the type of power cord supplied with your LCD monitor CONTROLS AND CONNECTORS Connecting the D Sub Cable Connect one end of the 15 pin VGA cable to the back of the monitor and connect the other end to the computer s D Sub port Connecting the Power Cord Plug the AC power cord one end to LCD monitor s AC input socket the other end to Wall outlet AC input socket D Sub input socket Figure 2 Connecting Cables ADJUSTING THE VIEWING ANGLE oe For optimal viewing it is recommended to look at the full face of the monitor then adjust the monitor s angle to your own preference Hold the stand so you do not topple the monitor when you change the monitor s angle You are able to adjust the monitor s angle from 3 to 11 NOTES Do not touch the LCD screen when you change the angle It may cause damage or break the LCD screen e Careful attention is required not to catch your fingers or hands when you change the angle Figure 3 Angle OPERATING INSTRUCTIONS GENERAL INSTRUC
2. 50 2 Press or to navigate through the functions Once the desired function is highlighted press the MENU button to activate it Ifthe function USES Ie selected has a sub menu press or again to navigate through the sub Eco mode 4 Standard P gt menu functions Once the desired function is highlighted press MENU button to activate it 3 Press or to change the settings of the selected function 4 To exit and save select the exit function If you want to adjust any other function repeat steps 2 3 DCR lt Off Figure5 The OSD Message ADJUSTING THE PICTURE The descriptions for function control coms __ EEE ECT A ETT a e o w FH Enable dynamic contrast ratio EE a PE Clock to reduce Vertical Line noise Luminance ase Ast Pure Prasetoradeeoraoralinereee postes Atte oro Poston ofthe we Peston __ Aste verica Poston ote tre Pam __ Real Warm Coor Temperature fm EEPROM Prema __ Recai Normal Color Temperature tom EEPROM Poet __ Ral Cool Coor Temperate tom EEPROM Red res Gain tom Dret 0000 e Image Setup Brightness KAA Adjust Frame Brightness Color Boost oms Astro Contest Reest Asteria postion ofFrane poston Aste vena postin efFrame m E Picture Boost poston Asteria Postinro meo Aste OSD Timeout reg _ seem osteg OOOO DJS OSD Setup Rest Reset the menu to default Information Show the Information of the main image and sub imag
3. EB1927WSL LCD MONITOR USER S MANUAL Before operating the monitor please read this manual thoroughly This manual should be retained for future reference FCC Class B Radio Freguency Interference Statement WARNING FOR FCC CERTIFIED MODELS NOTE This eguipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help NOTICE 1 The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to
4. DDC Serial clock Video Blue Detect Cable 10
5. rug or similar surface Do not place the monitor near or over a radiator or heat register Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided The monitor should be operated only from the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company e The monitor is equipped with a three pronged grounded plug a plug with a third grounding pin This plug will fit only into a grounded power outlet as a safety feature If your outlet does not accommodate the three wire plug have an electrician install the correct outlet or ground the appliance safely Do not defeat the safety purpose of the grounded plug e Unplug the unit during a lightening storm or when it will not be used for long period of time This will protect the monitor from damage due to power surges Do not overload power strips and extension cords Overloading can result in fire or electric shock e Never push any object into the slot on the monitor cabinet It could short circuit parts causing a fire or electric shock Never spill liquids on the monitor e Do not attempt to service the monitor by yourself opening or removing covers can expose you to dangerous voltages and other hazards Please refer all servicing to qualified service personnel To ensure satisfactory operation use the monitor only with UL listed computers which have appropriate configu
6. operate the equipment 2 Shielded interface cables and AC power cord if any must be used in order to comply with the emission limits 3 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is the responsibilities of the user to correct such interference WEEE Declaration Optional Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please ET contact your local city office your household waste disposal service or the shop where you purchased the product WEEE Declaration for India Optional This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste Instead it is your responsibility to dispose of your waste eguipment by handing it over to a designated collection
7. TIONS Press the power button to turn the monitor on or off The other control buttons are located at front panel of the monitor See Figure 4 By changing these settings the picture can be adjusted to your personal preferences e The power cord should be connected e Connect the video cable from the monitor to the video card e Press the power button to turn on the monitor position The power indicator will light up EXTERNAL CONTROLS Full amp 4 3 Menu Enter Power Button Figure4 External Control Button FRONT PANEL CONTROL Power Button Press the button to turn on or turn off the monitor Menu Enter Activate OSD menu when OSD is OFF or activate de activate adjustment function when OSD is ON ECO When OSD menu is in off status press this key continuously to select the different ECO mode Eco mode hot key may not be available in all models When OSD menu is in active status press this key as function select key Full amp 4 3 When OSD menu is in off status press this key continuously to change 4 3 or wide image ratio If the product screen size is 4 3 or input signal resolution is wide format the hot key is disable to adjust When OSD menu is in active status press this key as function select key e Auto Exit When OSD menu is in off status press this button to activate the Auto Adjustment function The Auto Adjustment function is used to set t
8. e source PLUG AND PLAY PLUG amp PLAY DDC2B FEATURE This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD It allows the monitor to inform the host system of its identity and depending on the level of DDC used communicate additional information about its display capabilities The DDC2Bis a bi directional data channel based on the 12C protocol The host can request EDID information over the DDC2B channel THIS MONITOR WILL APPEAR TO BE NON FUNCTIONAL THIS MONITOR TO OPERATE PROPERLY THERE MUST BE A VIDEO INPUT SIGNAL This monitor meets the Green monitor standards as set by the Video Electronics Standards Association VESA and The Swedish Confederation Employees NUTEK This feature is designed to conserve electrical energy by reducing power consumption when there is no video input signal present When there is no video input signal this monitor following a time out period will automatically switch to an OFF mode This reduces the monitor s internal power supply consumption After the video input signal is restored full power is restored and the display is automatically redrawn The appearance is similar to a Screen Saver feature except the display is completely off The display is restored by pressing a key on the keyboard or clicking the mouse TECHNICAL SUPPORT FAQ Problem amp Question Possible Solution Power LED is Not ON Make sure the power button is ON and the Power Cord is properly connec
9. evices that may cause electrical interference as far away from the monitor as possible Wave Pattern Appears In The Use the maximum refresh rate your monitor is capable of at the resolution your are using Picture Monitor Is Stuck In Active The Computer Power Switch should be in the ON position Off Mode The Computer Video Card should be snugly fitted in its slot Make sure the monitor s video cable is properly connected to the computer Inspect the monitor s video cable and make sure no pin is bent Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED The LED should either turn ON or OFF after hitting the CAPS LOCK key Missing one of the primary Inspect the monitor s video cable and make sure that no pin is damaged colors RED GREEN or Make sure the monitor s video cable is properly connected to the computer BLUE Screen image is not centered Adjust H Position and V Position or press hot key AUTO or sized properly Picture has color defects Adjust RGB color or select desired color temperature white does not look white Horizontal or vertical Use Windows 95 98 2000 ME XP shut down mode Adjust CLOCK and PHASE disturbances on the screen Press to auto adjust APPENDIX SPECIFICATIONS Model Name Viewable Image Size Pixel Pitch Active Display Area Frequency Range Pixel Clock Recommended Resolution Display Colors HDCP Function Input Signal Input Connector P
10. he HPos VPos Clock and Phase When OSD menu is in active status this button will act as EXIT KEY EXIT OSD menu Power Indicator Blue Power On mode Flickering Blue Standby mode OSD Lock Function To lock the OSD press and hold the MENU button while the monitor is off and then press power button to turn the monitor on To un lock the OSD press and hold the MENU button while the monitor is off and then press power button to turn the monitor on NOTES Do not install the monitor in a location near heat sources such as radiators or air ducts or in a place subject to direct sunlight or excessive dust or mechanical vibration or shock Save the original shipping carton and packing materials as they will come in handy if you ever have to ship your monitor For maximum protection repackage your monitor as it was originally packed at the factory To keep the monitor looking new periodically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution Never use strong solvents such as thinner benzene or abrasive cleaners since these will damage the cabinet As a safety precaution always unplug the monitor before cleaning it Do not scratch the screen with hard things it may cause permanent damage e Don t leak liquid into monitor which will result in the damage of component Aaa Luminance 1 Press the MENU button to activate the OSD window Contrast O mu
11. ower Supply Power Consumption ug amp Play ront Control peaker Weight monitor with stand EB1927WSL EB2027WSL EB2227WSL 47 0cm 18 5 diagonal 49 5cm 19 5 diagonal 54 7cm 21 5 diagonal 0 300mm Horizontal x 0 300mm Vertical 0 27mm Horizontal x 0 27mm Vertical 0 2482mm Horizontal x 0 2482mm Vertical 409 8mm Horizontal x 230 4mm Vertical 432 0mm Horizontal x 239 76mm Vertical 476 64mm Horizontal x 268 11mm Vertical Horizontal 30 kHz 60 kHz Vertical 50 Hz 76 Hz Horizontal 30 kHz 83 kHz Vertical 50 Hz 76 Hz 90MHz 140 MHz 165 MHz 1600x900 60Hz 1920x1080 060Hz 16 7M Colors 1366x768 60Hz Analog 0 7Vp p 75 OHM D Sub 15pin 100 240V 50 60 Hz 1 5 A Active 18W Typical Standby lt 0 5W Active 25W Typical Standby lt 0 5W Active 25W Typical Standby lt 0 5W Menu Enter gt ECO gt Full amp 4 3 gt Auto Exit gt Power Button 2 40Kg 25kg 273 444mm W x 343mm H x 176mm D 479mm W x 358mm H x 176mm D 512mm W x 377mm H x 176mm D Tilt 3 11 Pivot No Height adjust No Swivel No Temperature 0 Cto 40 C Humidity 10 to 85 non condensing Altitude 0 3658m 0 12000ft Temperature 25 Cto 55 C Humidity 5 to 93 non condensing Altitude 0 12192m 0 40000ft Preset Display Modes eoneoarae wan O OS O E lt lt Wich 7 Pin Assignments Signal Name Video Red Pano ETS a A A DDC Serial data
12. point for the recycling of waste electrical and electronic eguipment The separate collection and recycling of your waste eguipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste eguipment for recycling please contact your local city office your household waste disposal service or the shop where you purchased the product WARNING To prevent fire or shock hazard do not expose the monitor to rain or moisture Dangerously high voltages are present inside the monitor Do not open the cabinet Refer servicing to gualified personnel only PRECAUTIONS e Do not use the monitor near water e g near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement e Do not place the monitor on an unstable cart stand or table If the monitor falls it can injure a person and cause serious damage to the appliance Use only a cart or stand recommended by the manufacturer or sold with the monitor If you mount the monitor on a wall or shelf use a mounting kit approved by the manufacturer and follow the kit instructions e Slots and openings in the back and bottom of the cabinet are provided for ventilation To ensure reliable operation of the monitor and to protect it from overheating be sure these openings are not blocked or covered Do not place the monitor on a bed sofa
13. red receptacles marked between 100 240V AC Min 5A e The wall socket shall be installed near the equipment and shall be easily accessible SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem NOTES Due to the nature of the fluorescent light the screen may flicker during initial use Turn off the Power Switch and then turn it on again to make sure the flicker disappears You may find slightly uneven brightness on the screen depending on the desktop pattern you use The LCD screen has effective pixels of 99 99 or more It may include blemishes of 0 01 or less such as a missing pixel or a pixel lit all of the time Due to the nature of the LCD screen an afterimage of the previous screen may remain after switching the image when the same image is displayed for hours In this case the screen is recovered slowly by changing the image or turning off the Power Switch for hours BEFORE YOU OPERATE THE MONITOR FEATURES e 47 0cm 18 5 49 5cm 19 5 54 7cm 21 5 TFT Color LCD Monitor e Crisp Clear Display for Windows e Recommended Resolutions 1366x768 60Hz 18 5 1600x900 60Hz 19 5 1920x1080 60Hz 21 5 e Ergonomic Design e Space Saving Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The i se should include the t items EAU KS 5 pin D Sub Cable ICAC pea DE INSTALLATION INSTRUCTIONS Install Remove
14. ted to a grounded power outlet and to the monitor No images on the screen Is the power cord connected properly Check the power cord connection and power supply Is the cable connected correctly Connected using the D sub cable Check the DB 15 cable connection Connected using the DVI cable Check the DVI cable connection DVI input is not available on every model Connected using the HDMI cable Check the HDMI cable connection HDMI input is not available on every model If the power is on reboot the computer to see the initial screen the login screen which can be seen If the initial screen the login screen appears boot the computer in the applicable mode the safe mode for Windows ME XP 2000 and then change the frequency of the video card If the initial screen the login screen does not appear contact the Service Center or your dealer Can you see Input Not Supported on the screen You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly Adjust the maximum resolution and frequency that the monitor can handle properly Picture Is Fuzzy amp Has Adjust the Contrast and Brightness Controls Ghosting Shadowing Problem Press to auto adjust Make sure you are not using an extension cable or switch box We recommend plugging the monitor directly to the video card output connector on the back Picture Bounces Flickers Or Move electrical d

Download Pdf Manuals

image

Related Search

Related Contents

Manual de usuario  téléchargez le mode d`emploi "Museum Quest"  JVC XL-MV7000GD User's Manual  KOHLER K-98068-4-BN Installation Guide  Détecteurs de fumée, mode d`emploi  BH550 Manual English  Farberware FCP280 Use and Care Manual  D Montage- und Betriebsanleitung Installation and Operating  User Manual PocketBook Touch Lux BG  XIV PHARMACIE DE VOYAGE  

Copyright © All rights reserved.
Failed to retrieve file