USER Manual ROBOGM
Contents
1. ATLANTA SYSTEMS VEHICLE TRACKER UNIT COMMAND LIST OF TRACKAR S NO SYNTAX FUNCTION DESCRIPTION SYSSTARTZ System Start Phone Number Stored If Previous Number Of Subscriber Not Found SYSSTOPZ System Stop Entire System Will Stop Working RESET Reset Resets Full System bringing it to factory defaults System has to e started again TRACKERSTART lt D H M gt Tracker Start Tracker Start With lt Duration gt TRACKERSTOPZ Tracker Stop Tracker Stops Check Only For New SMS SENSESTARTZ Sensing Starts Door Sense Starts Working SENSESTOPZ Sensing Stops Door Sense Stops Working VCSTARTZ Vehicle Control Starts Ignition Horn Fuel Control Starts VCSTOPZ Vehicle Control Stops Ignition Horn Fuel Control Stops IGNITIONOFFZ Ignition Off Ignition Off IGNITIONONZ Ignition On Ignition On FUELONZ Fuel On Switches On The Fuel FUELOFFZ Fuel Off Switches Off The Fuel CARHORNONZ Car Horn On Continuously blows The Car Horn CARHORNOFFZ Car Horn Off Stops blowing the Car Horn IMEI Displays IMEI International Mobile Equipment Identity Number 15 Digits GETTEMP Displays Temperature Displays Temperature in C degree Celsius ALLLOC All Location Previous 5 Location Display GAIN lt XX gt Adjusts The Gain Adjusts The Gain for better communicati2. DISARM TRACKAR will stop monitoring the vehicle It will stop sensing the doors Start the ignition and fuel of the vehicle an conformation massage DISARM MODE HAS BEEN ACTIVATED will be received config APN username password This command is used to configure your GPRS account APN access point name which is used to get to the GPRS gateway provided by network operator Username for your GPRS account username is provided by your by network operator or else put ABC Password for your GPRS account username is provided by your by network operator or else put ABC Response SMS of this command i If the SIM is not GPRS activated you will receive GPRS not available on SIM card ii If APN settings do not match with your network operator or in case you have mistyped you will receive GPRS Settings Invalid Your Inputs APN XXX Usr_nm XXX Pwd XXX Pls confirm with n w operator amp resend iii If APN settings are working you will receive GPRS configured successfully GPRS APN XXX GPRS USER NAME XXX GPRS PASSWORD XXX ATLANTA SYSTEMS VEHICLE TRACKER UNIT 23 config This command replies with GPRS APN User Name and Password already saved Response SMS of this command i GPRS APN XXX GPRS USERNAME XXX GPRS PASSWORD XXX ii No GPRS APN Usr nm Pwd stored Further response of TRACKERSTART in ROBO GM In addition to the
3. RMDR I Command to remove insurance remainder ATLANTA SYSTEMS VEHICLE TRACKER UNIT e RMDR 0 YY MM DD message Is the command for user set remainder for a particular day Eg RMDR 0 11 08 01 B DAY OF MOHAN would give you a reminder on 01 08 2011 with message as B DAY OF MOHAN f RMDR O Command to remove user set remainder g RMDR To check the stored remainders h RMDR To remove all reminders 43 GEO FENCING Geo fencing can be defined in two ways a Based on area in kilometers a Command to add geo fencing based on distance GEOFENCE R 5 Where stands for adding geo fence R stands for geo fence based on distance and 5 stands for distance in kilometer Command to remove geo fencing based on distance GEOFENCE R Where stands for adding geo fence and R stands for geo fence based on distance b Based on area name 1 Command to add geo fencing based on area name GEOFENCE N Delhi Where stands for adding geo fence N stands for geo fence based on area name and Delhi stands for area name Command to remove geo fencing based on area name GEOFENCE N Where stands for adding geo fence and N stands for geo fence based on area name ATLANTA SYSTEMS VEHICLE TRACKER UNIT c To check geo fencing GEOFENCE Note GPS must be valid to set geo fencing 44 MADD 0 1 This command is used to enable
4. Response CONTROLLING NUMBER IS 91xxxxxxxx 38 GETLOC This command is used to get the present location of vehicle on his mobile Response Location name Note GPS and API KEY must be valid fr this 39 LFD 0 1 This command is used to enable or disable location name fetching during GPRS Response LOC FETCHING ENABLED LOC FETCHING DISABLED 40 PNS a b mobile no This command is used to add two extra controlling numbers Where a Ifor first number and a 2 for the second number b 1 for alert ON and b 0 for alert OFF Mobile number in the format 91 ATLANTA SYSTEMS VEHICLE TRACKER UNIT Example PNS 1 1 4919999999999 Response Personal number stored PNS1 919999999999 1 PNS2 41 RCALL 919876543210 This command is used to MAKE CALL TO THE NUMBER 919876543210 Response TRACKER would make call to the given mobile 42 REMINDERS There are three remainders in tracker a POLLUTION For vehicle pollution remainder b INSURANCE For vehicle insurance remainder c OTHER here the user can set any remainder RMDR P YY MM DD Is the command to set pollution remainder for a particular day Eg RMDR P 11 08 01 would give you a reminder for pollution on 01 08 2011 RMDR P Command to remove pollution remainder RMDR 1 YY MM DD Is the command to set insurance remainder for a particular day Eg RMDR 1 11 08 01 would give you a reminder for insurance on 01 08 2011
5. It will be easier for you to find the information in the event of emergency to locate your vehicle at any unknown place through remote control system Your dealer will be pleased to clarify any queries you may have with the system or its operation Hope you derive as much pleasure in using it as we have derived from developing it Yours Truly MANAGING DIRECTOR ATLANTA SYSTEMS VEHICLE TRACKER UNIT PACKAGING CONTENTS Unpack the TRACKAR Box carefully in the package you will find e Operation Manual 1 No Vehicle Tracker Unit ROBO GM with internal battery 1 No Speaker 1 No Microphone 1 No Wire Jointer 2 Nos Relay With Socket 2 Nos Wiring Harness 1 Set GSM GPS Combo Antenna 1 No Note We suggest that you keep the packing material for future use RECOMMENDATION We recommend that you keep this manual and your car documents together It is important that you read the complete user manual for trouble free operation Although protected by a high level security system the installation of the security system is not an insurance against theft it is only a step towards precaution It is advisable and good practice to always take a series of precautions when the vehicle is left unattended PRECAUTIONS While washing the engine protect the TRACKAR by all suitable means from being struck directly by water jet or flow The GSM functionalities are dependent on the Network Postpaid Prepaid SIM card can be used
6. or weak network connection could be the reason Resend the desired commands again Reset the TRACKAR SMS is not received Please check the network status Location identification is in progress Trackar is fetching the GSM location from the cell tower Invalid GPRS Settings Invalid GPRS Settings Try resending the command Check with the network operator ATLANTA SYSTEMS VEHICLE TRACKER UNIT WIRING DIAGRAM OF TRACKAR WIRING ASSEMBLY FOR VTS DATE OF PUBLISHING 25 July 2013 MANUAL VERSION 1
7. will be received This command will work only when vehicle control on has been activated FUELOFFZ TRACKAR will stop fuel and confirmation message FUEL OFF HAS BEEN ACTIVTED will be received This command will work only when vehicle control on has been activated CARHORNONZ TRACKAR will start the vehicle horn and confirmation message CAR HORN ON HAS BEEN ACTIVATED will be received This command will work only when vehicle control on has been activated CARHORNOFFZ TRACKAR will stop vehicle horn and confirmation message CAR HORN OFF HAS BEEN ACTIVATED will be received This command will work only when vehicle control on has been activated IMEI TRACKAR will display International Mobile Equipment Identity Number 15 Digits GETTEMP Displays Temperature in C degree Celsius of vehicle ATLANTA SYSTEMS VEHICLE TRACKER UNIT ALLLOC TRACKAR will send previous locations of the vehicle and confirmation message LOCATION lt FOLLOWED BY LAST FIVE STORED BTS LOCATION gt will be received TRACKAR will accept this command only in TRACKERSTART mode GAINxx TRACKAR adjusts the gain for voice communication by sending this command The value of xx can be adjusted from 01 to 15 ARM TRACKAR will start monitoring the vehicle It will start sensing the doors lock the door cut the ignition and fuel of the vehicle and confirmation massage ARM MODE HAS BEEN ACTIVATED will be received
8. C Customer Mode Door S Closed Ign_OFF VC_OFF DISARM Sleep_OFF Fuel N C PNS Phone Numbers Stored PNS1 c b PNS2 c b PNS a b c a 1 for PNS1 a 2 for PNS2 b 0 for alerting off b 1 for alerting on C 91xxxxxXxXXXxx Phone Numbers Stored PNS1 c b PNS2 c b ATLANTA SYSTEMS VEHICLE TRACKER UNIT SLEEP UNIT IS OUT OF SLEEP if not in sleep UNIT IS IN SLEEPGf in sleep GSENSE GSENSOR WORKING UNIT IS IN NOT IN MOTION AND IT IS NOT IN IN SLEEP MODE SETODO 12345 Odometer set to 12345 00 SETODO Odometer reading 12345 00 BAL 123t REPLAY FROM NETWORK GETLOC Location name would come SIMSERVER CURRENT SERVER NO IS 91xxxxxxx SIMSERVER 9 1 xxxxxxxx SIM SERVER CHANGED TO 9 1xxxxxxx SIMSERVER SIM SERVER REMOVED LFD 0 LOC FETCHING ENABLED LFD 1 LOC FETCHING DISABLED CON NO CONTROLLING NUMBER IS 91XXXXXXX GETLOCAGPS Location name would come RMDR P YY MM DD Pollution alert set for RMDR 1 Y Y MM DD Insurance alert set for RMDR 0 Y Y MM DD message Other alert set for RMDR P Pollution alert removed RMDR O Other alerts removed RMDR I Insurance alert removed RMDR Removed all alerts RMDR The set alerts are GEOFENCE N Delhi GEOFENCING SET FOR NAME Delhi
9. GEOFENCE NAMED GEOFENCE REMOVED GEOFENCE RADIUS GEO FENCE SET GEOFENCE RADIUS GEOFENCE REMOVED GEOFENCE gives set geo fence details if any MADD 0 MISSED CALL BASED ARM DISARM FEATURE ENABLED MADD 1 MISSED CALL BASED ARM DISARM FEATURE DISABLED RCALL 91 No replay from tracker Trackar would make call to the given number CO GSM operator name would come CCID GSM operator cell ID would come ATLANTA SYSTEMS VEHICLE TRACKER UNIT CAD 0 COMMON ALERTS ENABLED CAD 1 COMMON ALERTS DISABLED fuelcal SN LTR SN Fuel value calibrated for volume LTR litres with ADC value xxx xxx fuelcalFS Fuel calculation started ATLANTA SYSTEMS VEHICLE TRACKER UNIT TROUBLE SHOOTING SCENARIO IN GENERAL SEND SMS TROUBLE SHOOTING Unexpected error UNEXPECTED ERROR If you receive unexpected error message then sensing tracking vehicle control needs to be reactivated Send previous message SEND PREVIOUS MESSAGE Resend the previous command SMS not accepted SMS NOT ACCEPTED There may be some spelling mistake in the command or the command may be invalid Please recheck the command phrase and resend No response from TRACKAR Check your balance in case of Pre Paid connection Check the network status No
10. MOBILE EQUIPMENT IDENTITY NUMBER GETTEMP Temp XX CELCIUS LOCATION lt FOLLOWED BY LAST FIVE STORED BTS LOCATION gt GAIN lt XX gt GAIN HAS BEEN ACTIVATED ARM ARM MODE HAS BEEN ACTIVATED DISARM DISARM MODE HAS BEEN ACTIVATED VERSION SYSTEM VERSION NO xxx WEBSTART lt D H M gt Data sending to web started XXX WEBSTOPZ Data Sending to WEB Stopped GPRS APN XXX config GPRS USERNAME XXX GPRS PASSWORD XXX TRACKERSTART lt D H M gt VCSTARTZ VCSTOPZ ALLLOC ATLANTA SYSTEMS VEHICLE TRACKER UNIT config APN username password GPRS configured successfully GPRS APN XXX GPRS USER NAME XXX GPRS PASSWORD XXX SLEEPOFF Sleep on GPRS activated SLEEPON Sleep on GPRS De activated GETGPS Lat XXX It will tell you the latitude of the location Long XXX It will tell you the longitude of the location Speed XXX It will tell you the speed of the vehicle in KPH Date XXX It will tell you the date of this particular data Time XXX It will tell you the time of this particular data in IST Imei XXX It will tell you International Mobile Equipment Identity Number NS y XXXXX Numbers Stored NS1 XXX NS2 XXX NS3 XXX NS4 XXX GSM ON XXXM D H GSM_OFF GPRS_ON XXXM D H S GPRS_OFF Test Mode Door S Open Ign ON VC_ON ARM Sleep_ON Fuel
11. Pay special attention to the amount of remaining credit amp expiry date of mobile connection in case of prepaid SIM card Do not remove SIM while the TRACKAR is in power on condition Note Availability of location name is dependent on mobile service provider If the service provider is giving the name of locality in cell info display TRACKAR will also show name of locality Please note that ARM MODE or FUEL OFF commands will immediately bring the vehicle to a sudden halt Hence we strongly recommend that these commands should not be used when vehicle is moving as sudden stop may result in some mishappening ATLANTA SYSTEMS VEHICLE TRACKER UNIT TRACKAR UNIT FEATURES High sensitive GPS chipset Combination of GPS GSM GPRS wireless network Durable and highly reliable GPS tracker Easy to install or hide in the vehicle to perform tracking Ideal application for vehicle tracking and equipment assets monitoring External DC power supply Configuration can be done via SMS commands Real time GSM GPS location monitoring on SMS and website Real time asset monitoring with related alerts Vehicle control with Immobilization Voice monitor function with live discreet two way sound conversation Generation of reports on web site in html xls format Reports include drive stop summary Performance based on speed Detail with time date latitude longitude speed Replay and analysis of trip logs Add on users
12. Vehicle is in stand still Response SMS of this command Sleep on GPRS activated ATLANTA SYSTEMS VEHICLE TRACKER UNIT 30 SLEEPOFF This command is used to disable SLEEPON mode Response SMS of this command Sleep on GPRS De activated 31 SLEEP To check whether the unit is IN SLEEP OR NOT 32 SYSSTATUS GSM ON XXXM H D GSM OFF GPRS ON XXXM H D S GPRS OFF Test Mode Customer Mode Door S Open Door S Closed Ign ON Ign OFF VC ON VC OFF ARM DISARM Sleep ON Sleep OFF Fuel c Fuel N C Response 33 GSENSE This command is used to check the condition of vehicle whether IN MOTION OR NOT and status of tracker whether IN SLEEP OR NOT Response GSENSOR WORKING UNIT IS IN NOT IN MOTION AND IT IS NOT IN IN SLEEP MODE 34 SETODO 12345 This command is used to calibrate the odometer where 12345 is the present odometer reading Response Odometer set to 12345 00 35 SETODO This command is used to get read the present accelerometer reading of vehicle ATLANTA SYSTEMS VEHICLE TRACKER UNIT Response Odometer reading 12345 00 36 BAL 123 This command is used to check the balance amount of a TRACKAR SIM where 123 is the number for balance check in airtel network and may be different for different opereators Response Response for this command would be the replay from network 37 CON NO This command is used to check controlling number of a particular device
13. tracking of vehicle TRACKAR will send location of the area to the subscriber number at a particular interval described by the subscriber Example 1 TRACKERSTART001D By sending the above command TRACKAR will start tracking the location of Vehicle immediately When location is found by the TRACKAR it will send this location to subscriber number and the next location will come after one day exactly at same time and this sequence will continue In our example we mentioned 001D here D stands for DAY 001 for 1 meaning I day Confirmation message TRACKING START 001D HAS BEEN ACTIVATED will be received by the user Example 2 TRACKERSTART002H By sending the above command TRACKAR will start tracking the location of Vehicle immediately When location is found by the TRACKAR it will send this location to subscriber number and the next location will come after 2 hour and this sequence will continue In our example we mentioned 002H here H stands for HOUR 002 for 2 meaning 2 hours Confirmation message TRACKING START 002H HAS BEEN ACTIVATED will be received by the user Example 3 TRACKERSTARTO005M By sending the above command TRACKAR will start tracking the location of Vehicle immediately When location is found by the TRACKAR it will send this location to subscriber number and the next location will come after 5 minutes and this sequence will continue In our example we mentioned 005M here M stands for MINUTE
14. with customized access to web accounts Register the vehicle with user mobile number no other number will work Deregister the vehicle with only user mobile number no other number can be used to deregister from the system Location of the vehicle can be found at user defined interval it can be set for I minute to 365 days Location feature can be started stopped by the user on the mobile Last five location of the vehicle can also be found Door sense can be started stopped by the user Vehicle control function Ignition off on fuel off on Horn off on can be started stopped by the user Incoming call to the vehicle can be answered by the TRACKAR when the call is from the registered mobile number ATLANTA SYSTEMS VEHICLE TRACKER UNIT Confirmation of command SMS will be received by the user if any feature of the TRACKAR is activated or deactivated Easy installation and easy SMS commands Gain for voice communication can be adjusted to improve the sound quality If wrong SMS command sent by the user then TRACKAR will delete SMS and send SMS NOT ACCEPTED to user mobile number User can check the balance of TRACKAR Mobile No by themselves User can get the location on his mobile by sending GETLOC command User would get a google map link on mobile with Latitude longitude Over The Air OTA software updation User can control TRACKAR through 3 more nos User can take the ODO
15. 005 for 5 meaning 5 minutes Confirmation message TRACKING START 005M HAS BEEN ACTIVATED will be received by the user Note The Tracking Timing May Vary Depending Upon The Network Congestion ATLANTA SYSTEMS VEHICLE TRACKER UNIT TRACKERSTOPZ TRACKAR will stop tracking the location of the vehicle Confirmation message TRACKER STOP HAS BEEN ACTIVATED will be received SENSESTARTZ TRACKAR will start sensing doors Confirmation message SENSE START HAS BEEN ACTIVATED will be received SENSESTOPZ TRACKAR will stop sensing doors Confirmation message SENSE STOP HAS BEEN ACTIVATED will be received VCSTARTZ TRACKAR will start controlling FUEL ON OFF IGNITION ON OFF HORN ON OFF Confirmation message VEHICLE CONTROL START HAS BEEN ACTIVATED will be received VCSTOPZ TRACKAR will stop controlling vehicle FUEL IGNITION HORN and confirmation message VEHICLE CONTROL OFF HAS BEEN ACTIVATED will be received IGNITIONOFFZ TRACKAR will stop ignition and confirmation message CAR IGNITION OFF HAS BEEN ACTIVATED will be received This command will work only when vehicle control on has been activated IGNITIONONZ TRACKAR will start ignition and confirmation message CAR INGITION HAS BEEN ACTIVATED will be received This command will work only when vehicle control on has been activated FUELONZ TRACKAR will start fuel and confirmation message FUEL ON HAS BEEN ACTIVTED
16. METER reading on Mobile as well as on website Panic Button can be used to generate SMS and call in case of emergency Note This function will work if you have additionally purchased the Panic Button Kit Fuel Liquid sensing to know the amount of fuel present in tank Note This function will work if you have additionally purchased the Fuel Calibrator Digital Fuel Sensor HARDWARE DESCRIPTION a Power Requirement 8V to 33V b Normal operation temperature 10 C to 70 C c Restricted operation temperature Above 10 C and below 70 C d Storage temperature 45 C to 90 C e Humidity 5 to 95 ATLANTA SYSTEMS VEHICLE TRACKER UNIT SMS COMMANDS DESCRIPTION 1 SYSSTARTZ This command is used to register the TRACKAR with Subscriber number Now TRACKAR will respond to subscriber number only no other phone number will work Confirmation message SYSTEM START HAS BEEN ACTIVATED will be received by the registered number SYSSTOPZ This command is used to stop the system with Subscriber number Now a new number can be registered with TRACKAR RESET This command brings the TRACKAR on factory defaults the subscriber name and all other stored information is deleted from TRACKAR Conformation message SYSTEM RESET COMPLETE will be received by the registered number System has to be started again TRACKERSTART lt xxxD gt lt xxxH gt lt xxxM gt This command is used to start the TRACKAR for
17. R NOT GSENSE Check the status of vehicle To check the condition of vehicle whether IN MOTION OR NOT and status of tracker whether IN SLEEP OR NOT SETODO 12345 Set the odometer reading of vehicle To calibrate the odometer where 12345 is the present odometer reading SETODO Get the status of odometer To get read the present accelerometer reading of vehicle SIMSERVER check current sim server check current sim server SIMSER VER 4 91xxxxxxxx To add change new simserver To add change new simserver SIMSERVER To remove current simserver To remove current simserver BAL 123 Used to know the Trackar sim balance To check the balance amount of a SIM where 123 is the number for balance check in airtel network and may be different for different opereators GETLOC For current location To get present location name of tracker LFD 0 To enable location fetching property To enable location fetching property LFD 1 To disable location fetching property To disable location fetching property CON NO To check controlling number of a particular device To check controlling number of a particular device GETLOCAGPS To get location name based on AGPS To get location name based on AGPS mes A ES ATLANTA SYSTEMS VEHICLE TRACKER UNIT RMDR P YY MM DD To set the pollution al
18. TRACKAR ATLANTA USER MANUAL ROBO GM INDEX S No FUNCTION 1 2 3 4 5 6 7 8 9 pam o INTRODUCTION PACKAGING CONTENTS RECOMMENDATION PRECAUTIONS TRACKAR UNIT FEATURES SMS COMMANDS DESCRIPTION OPERATION MANUAL COMMAND LIST OF TRACKAR COMMAND AND RESPONSE SMS TROUBLE SHOOTING WIRING DIAGRAM OF TRACKAR DATE OF PUBLISHING 25 July 2013 MANUAL VERSION 1 INTRODUCTION Dear Customer Congratulations on being the owner of this product which has been designed and manufactured to the highest automotive standards utilizing the latest technology for total reliability Vehicle tracker unit TRACKAR is a new remote vehicle security system with a host of comfort features The TRACKAR enables you to communicate directly with your vehicle Locate and or immobilize the vehicle in real time if the car is lost or robbed The possibility to interact with the system by means of short text message SMS gives the owner total management of the events concerning their vehicle i e it can also arm disarm speak to the car and cut off fuel and ignition connection The TRACKAR addresses customer needs to the fullest by incorporating State of the Art Technology and Design of Automotive Standards accompanied with best after sales service and unparalleled network throughout India Please read this manual to get the full benefit of the system We suggest you keep this manual at a secure place
19. ake call from the TRACKAR To make call to the given mobile number To chek GSM operator name To check the GSM operator of SImc ard using in the TRACKAR To check GSM operator cell ID To check the GSM operator cellID To enable common alerts To enable the alert firing ATLANTA SYSTEMS VEHICLE TRACKER UNIT CAD 1 To disable common alerts To disable alert sending fuelcal SN LTR To caliberate the fuel SN Fuel value calibrated for volume LTR litres with ADC value XXX XXx fuelcalFS To start fuel calculation Fuel calculation started ATLANTA SYSTEMS VEHICLE TRACKER UNIT COMMAND and RESPONSE SMS SMS COMMAND SMS RESPONSE SYSSTARTZ SYSTEM START HAS BEEN ACTIVATED SYSSTOPZ SYSTEM STOP HAS BEEN ACTIVATED RESET SYSTEM RESET COMPLETE A TRACKING START XXXM H D HAS BEEN ACTIVATED B LOCATION lt NAME OF BTS AREA LOCATION gt TRACKERSTOPZ TRACKER STOP HAS BEEN ACTIVATED SENSESTARTZ CAR SENSE HAS BEEN ACTIVATED SENSESTOPZ CAR SENSE STOP HAS BEEN ACTIVATED VEHICLE CONTROL START HAS BEEN ACTIVATED VEHICLE CONTROL STOP HAS BEEN ACTIVATED IGNITIONOFFZ IGNITION OFF HAS BEEN ACTIVATED IGNITIONONZ IGNITION ON HAS BEEN ACTIVATED FUELONZ FUEL ON HAS BEEN ACTIVATED FUELOFFZ FUEL OFF HAS BEEN ACTIVATED CARHORNONZ CAR HORN ON HAS BEEN ACTIVATED CARHORNOFFZ CAR HORN OFF HAS BEEN ACTIVATED IMEI 15 DIGIT INTERNATIONAL
20. ert To set the pollution alert for the day YY MM DD RMDR 1 Y Y MM DD To set the insurance alert To set the insurance alert for the day YY MM DD RMDR 0 Y Y MM DD message To set user defined alert To set the user defined alert for the day YY MM DD with message RMDR P To remove the pollution alert To remove the set pollution alert RMDR O To remove the user defined alert To remove the set user defined alert RMDR I To remove the insurance alert To remove the set insurance alert RMDR To remove all alerts To remove all set alerts RMDR To check the alert To check all the set alerts GEOFENCE N Delhi To set geofence based on area name To set geofence alert based on the area name Delhi GEOFENCE To remove geofence alert To remove geofence alert based on area name GEOFENCE To set radius based geofence alert To set radius based geofence alert for a radius of 2km GEOFENCE To remove radius based geofence alert To remove set radius based geofence alert GEOFENCE To check the set geofence alerts To check the set geofence alerts MADD 0 To enable missed call based ARM DISARM property To enable missed call based ARM DISARM property MADD 1 To disable missed call based ARM DISARM property To disable missed call based ARM DISARM property RCALL 91 To m
21. g msg amp resend If GPRS configuration is already done you will receive Data sending to web started XXX 26 To Stop live tracking on internet Send WEBSTOPZ to TRACKAR Response SMS of this command Data Sending to WEB Stopped To get GPS data for one time Send GETGPS to TRACKAR Response SMS of this command TRACKAR will send i If the GPS satellites are unreachable you will receive GPS NOT FOUND ii If the GPS satellites are reachable you will receive Lat XXX It will tell you the latitude of the location Long XXX It will tell you the longitude of the location Speed XXX It will tell you the speed of the vehicle in KPH Date XXX It will tell you the date of this particular data Time XXX It will tell you the time of this particular data in IST Imei XXX It will tell you International Mobile Equipment Identity Number Web link to view location It will show you the location on map To observe the exact location on Google map for a corresponding LAT LONG open www maps google com in the search bar enter the latitude and longitude coordinates separated with a comma It will show you the location SLEEPON By default sleep mode is on Sleep mode is used to deactivate data sending on GPRS when the vehicle is on a stand still for a particular time As soon as the Vehicle starts moving again the trackar will start sending data again This mode is provided to save battery when the
22. less than 1 day or more than 365 days H means HOURS the system will accept from 1 to 24 hours it will reject less than 1 hour or more than 24 hours M means MINUTES the system will accept from 1 to 60 minutes it will reject less than 1 minute or more than 60 minutes S means Seconds the system will only accept WEBSTARTO30S it will reject any other value Example when we send this command WEBSTART002M TRACKAR will start sending the data to our web server at the given interval time ATLANTA SYSTEMS VEHICLE TRACKER UNIT FUEL CALIBRATION IN TRACKAR In TRACKAR fuel can be calibrated in two ways 1 Using Existing CAR SENSOR In this method we use variable resister to restrict the sensor output with in the range 0 2 5V Using Separate FMB In this method we place an extra device called FMB with car sensor to filter noise For both the above methods calibration procedure would be as follows a b Tank would be emptied Tank would be gradually filled in appropriate steps 2 5 10 20 SOLTRs etc For each step a SMS is required to be send from the controlling number in the following format fuelcal SN LTR Where SN is serial number within the range of 00 to 19 And LTR is the fuel available in the tank at the given step and its range is from 000 to 999 For each SMS the controlling number would get a reply Eg for fuelcal 03 050 would give replay as 03 Fuel value calibrated for volume 050
23. litres with ADC value 557 980 Repeat step c until the tank is full Send fuelcalFS from controlling number to start fuel calculation ARM MODE When you send ARM SMS to TRACKAR TRACKAR activates the arm mode DISARM MODE When you send DISARM to TRACKAR TRACKAR activates the disarm mode ATLANTA SYSTEMS VEHICLE TRACKER UNIT SENSING MODE 1 Using subscriber mobile phone send SENSESTARTZ SMS to TRACKAR TRACKAR will now be able to sense door 2 If door is open in this mode then TRACKAR will send DOOR IS OPEN SMS and dial the subscriber phone number CONTROL MODE Using subscriber mobile phone send VCSTARTZ SMS to TRACKAR TRACKAR will now be able to control fuel Ignition Horn Subscriber can send desired SMS command to ON OFF fuel ON OFF Ignition and ON OFF Horn To OFF Fuel send FUELOFFZ SMS to TRACKAR To ON Fuel send FUELONZ SMS to TRACKAR To OFF Ignition send IGNITIONOFFZ SMS to TRACKAR To ON Ignition send IGNITIONONZ SMS to TRACKAR To OFF Vehicle horn send CARHORNOFFZ SMS to TRACKAR To ON Vehicle horn send CARHORNONZ SMS to TRACKAR TWO WAY COMMUNICATION e Dial the TRACKAR number from subscriber mobile phone TRACKAR will answer this call no other number can be accepted by the TRACKAR e Gain adjustment Adjust the GAIN of TRACKAR by sending command GAINxx for voice communication The value of xx can be adjusted from 01 to 15
24. location you will receive the following information at the decided interval Lat XXX It will tell you the latitude of the location Long XXX It will tell you the longitude of the location Speed XXX It will tell you the speed of the vehicle in KPH Date XXX It will tell you the date of this particular data Time XXX It will tell you the time of this particular data in IST Web link to view location It will show you the location on map To start live tracking on internet Send WEBSTART lt xxxD H M S gt to TRACKAR TRACKAR will send confirmation SMS and then start sending data to our web server e xxx means digits from 0 9 D means DAYS the system will accept from 1 to 365 days it will reject less than 1 day or more than 365 days H means HOURS the system will accept from 1 to 24 hours it will reject less than 1 hour or more than 24 hours M means MINUTES the system will accept from 1 to 60 minutes it will reject less than I minute or more than 60 minutes S means Seconds the system will only accept WEBSTARTO30S it will reject any other value Example when we send this command WEBSTART002M TRACKAR will start sending the data to our web server at the given interval time NOTE Before first WEBSTART command it is mandatory to send config command Response SMS of this command If GPRS configuration config is not send you will receive ATLANTA SYSTEMS VEHICLE TRACKER UNIT Pls send confi
25. on ARM ARM Mode Active ARM Mode Is Activated DISARM DISARM Mode Active DISARM Mode Is Activated VERSION Shows the VERSION current Current version of the system is obtained WEBSTART lt D H M gt Start web tracking Starts sending GPS data to server WEBSTOPZ Stop web tracking Stops sending GPS data to server config Check GPRS settings Replies with previously stored apn usrname password config APN username password GPRS settings Enables GPRS on the SIM card SLEEPON Enables sleep mode Sleep mode is activated to save battery SLEEPOFF Disables sleep mode sleep mode is de activated ATLANTA SYSTEMS VEHICLE TRACKER UNIT GETGPS Get gps data on sms Replies with latitude longitude speed time information NS 91xxxxxxx Pre feed numbers to make call on SOS Stores numbers for call out on sos and sms server NSL Check pre feeded numbers Replies with the prefeed call in out sos and sms server numbers SYSSTATUS Status inquiry Get the status of the tracker PNS a b c Used to store two pre defined numbers PNS1 Number stored for 1 Parallel number PNS2 Number stored for 2 Parallel number PNS Query the numbers already stored To know the PNS numbers already stored SLEEP Used to check the sleep To check whether the unit is IN SLEEP O
26. or disable the antitheft mode based on missed call Response MISSED CALL BASED ARM DISARM FEATURE ENABLED MISSED CALL BASED ARM DISARM FEATURE DISABLED 45 GETLOCAGPS This command is used to get location name based on AGPS Note AGPS key must be valid for this This command is used to check the GSM operator name This command is used to check the GSM operator cell ID This command is used to enable or disable the ALERTS Response COMMON ALERTS ENABLED COMMON ALERTS DISABLED ATLANTA SYSTEMS VEHICLE TRACKER UNIT OPERATION MANUAL Insert a SIM card in TRACKAR Please remember the card number amp assigned mobile number REGISTRATION MODE Using your mobile phone send SYSSTARTZ SMS to TRACKAR now your mobile phone is registered to TRACKAR TRACKAR will not accept SMS from any other phone number DEREGISTRATION MODE Using subscriber mobile phone send RESET SMS to TRACKAR now TRACKAR will Reset itself to factory default Working of the entire system stops after sending this command TRACKING MODE 1 Start tracker Send TRACKERSTART lt xxxD H M gt to TRACKAR TRACKAR will send confirmation SMS and then send location of the vehicle if found and next location will come after set interval e xxx means digits from 0 9 e D means DAYS the system will accept from 1 to 365 days it will reject less than 1 day or more than 365 days H means HOURS the system will accept from 1 to 24 hours it will reject less
27. than I hour or more than 24 hours M means MINUTES the system will accept from I to 60 minutes it will reject less than I minute or more than 60 minutes Example when we send this command TRACKERSTARTO002M TRACKAR will give first location immediately after receiving this SMS and next location will come after every 2 minutes as we have wrote 002M and this process will continue You can program this tracker from minimum 1 minute to maximum 365 days Default interval is for 60 minutes 2 Stop tracker Send TRACKERSTOPZ to TRACKAR TRACKAR will stop sending location of the vehicle ATLANTA SYSTEMS VEHICLE TRACKER UNIT All location Send ALLLOC to TRACKAR to receive previous five locations of the vehicle TRACKAR will accept this command only in TRACKERSTART mode To start live tracking on INTERNET 1 config APN username password This command is used to configure your GPRS account APN access point name which is used to get to the GPRS gateway provided by network operator Username for your GPRS account username is provided by your by network operator or else put ABC Password for your GPRS account username is provided by your by network operator or else put ABC Send WEBSTART lt xxxD H M S gt to TRACKAR TRACKAR will send confirmation SMS and then start sending data to our web server e xxx means digits from 0 9 D means DAYS the system will accept from 1 to 365 days it will reject
Download Pdf Manuals
Related Search