Pioneer User Manual - Test Equipment Depot
Contents
1. OHAUS PAJ Series NTEP MC Certified Models Instruction Manual EN 1 1 INTRODUCTION 1 1 Safety Precautions Please follow these safety precautions PAJ N Series e Verify that the AC Adapter input voltage matches the local AC power supply e Use the balance only in dry locations e Do not operate the balance in hostile environments e Do not drop loads on the platform e Do not place the balance upside down on the platform or platform mounting cone e Service should be performed only by authorized personnel 1 2 Controls Button Functions Zero On short Press Off Long Press Yes Short press Menu Unit Short Press Menu Long Press No Short press Menu Long press Menu Tare Short Press Long Press Print Short Press Cal Long Press 2 INSTALLATION 2 Package Contents Gold Models Instruction Manual Power Adapter Balance Pan Pan Support Wind Ring Warranty Card Turns balance on sets display to zero Turns balance off selects or accepts setting Steps through active units and modes Enters Menu Steps through available settings Exit menu or abort out of menu item Performs Tare function no function sends data Initiates Span Calibration Carat Models Instruction Manual Power Adapter Balance Pan Glass Doors and Panels Gem Scoop Carat models only Warranty Card PAJ N Series EN 2 2 2 Install Components Gold Models 1 Install Wind Ring Carat2. Models md h E 1 Install Side Doors Insert fully into Top Frame then down over retainer mi m 3 Install Top Door 4 Install Pan EN 3 PAJ N Series 2 3 Level Balance Level the balance on a firm steady surface Avoid locations with excessive air current vibrations heat sources or rapid temperature changes 2 4 Connect Power For use with CSA Certified or equivalent approved power source which must have a limited circuit output 2 5 Initial Calibration Without InCal Power on the balance by pressing O T Press and hold Print Cal until CAL is displayed The display flashes the calibration mass needed To select the alternate calibration weight press No Put the calibration mass on the pan The display flashes busy then CLER FAA Remove the mass When calibration is complete d amp RE is displayed InCal Press and hold Print Cal until CAL is displayed The display flashes 5454 when calibration is complete dGRE is displayed Note Calibrations should be performed after a warm up time of 60 minutes 3 OPERATION Count Percentage or specific units of measure must be activated in tne MODE or UNIT menus if they are not initially available 3 1 Weighing Mode Repeatedly press Unit until the desired unit icon is displayed Press Zero to zero the balance and then place objects to be weighed on fhe pan Press Tare to zero the weight of a weighing contai
3. UNCE END PRT 1 END R232 UNIT i f i POUND PRINT NOT ALL HOW RS232 TEE NO nCal models only Notavailable with InCal yYes END UNIT END LOCK ENTER MENU When the balance is on press and hold Unit Menu until ERU appears Release the button and the Calibrate CRL menu will display MENU NAVIGATION Select menus menu items and settings through use of the Yes and No buttons Solid arrows point to the content displayed when Yes is pressed Dashed lines when No is pressed CHANGE SETTINGS To select the displayed Setting press Yes To move to the next Setting press No EXIT MENU When fd is displayed press Yes to exit the menu function or press No fo return to the Cal menu Note Press and hold No at any time to exit quickly Hi EN 5 PAJ N Series 4 2 Calibration Menu CRL InCal or Span calibration should be performed daily and when the room temperature changes InCal nfAL calibrates the balance using an internal mass InCal models only span Calibration SPAR uses two weight values zero and a weight between 50 and 100 of the capacity of the balance Linearity Calibration t uses three weight values zero 50 of the capacity and full capacity Generally this calibration is not required unless testing shows thet the linearity error exceeds the linearity tolerance in the specification table Not available in InCa
4. ategory Class Il 7 1 Drawings Gold Models 19 6cm 9 2 cm 32cm Carat Models 19 6 cm 32 cm 7 2 Specifications External Calibration Models moveu Paszoosn _ raveian Pas2t0an pasaron piusnoaw PAJSTOTN Pasai02N PAIATOIN d 0 005et_ O0lg Olg OOlg Olg OOlg Olg e O05 PQ Approval Class Il Tare Range To capacity by subtraction stabilization 3 Seconds po SSeonds S Span cal 200g or 400g E 1000g or 2000g 2000gor3000g 2000g or 4000g Lin cal 500g masses 200g 400g 800g 1000g 2000g 2000g 3000g 2000g 4000g Pan Size 7 1in 18cm PAJ models 6 1 x 7 1in 16 8 x 18cm Net Weight 10 Ib 4 5kg EN 9 PAJ N Series InCal Models MODEL PAJ603CN PAJ1003CN 600ct 1 000ct 0 001ct 0 01ct e To capacity by subtraction Max Min Pan dia Min t A T O3 5in j9cm Net Weight 10 1 Ib 4 6kg 7 3 Communication 7 3 1 Commands The RS232 Interface allows a computer to control the balance as well as receiving data such as the displayed weight The balance will return ES for invalid commands CP xP T ON OFF PSN PV PU Xi PH X96 P 7 3 2 RS232 DB9 Pin Connections Pin 2 Balance transmit line TxD Pin 3 Balance receive line RxD Pin 5 Ground signal GND Pin 7 Clear to send hardware handshake CTS Pin 8 Request to send hardware handshake RTS Print current mode unt oo Print current mode unit Set PC ref wt X
5. ation masses Use correct calibration masses Er70 gJTimou J o RO Checksum error Eon the authorized dealer REF Err Reference Weight is too small Add additional samples LOWrEF Reference Weight is too low for accurate Add additional samples or continue to weigh parts counting or percent weighing with less accurate results 6 2 Service Information If the troubleshooting section does not resolve or describe your problem contact your authorized Ohaus service agent Please visit our web site www ohaus com to locate the Ohaus office nearest you 6 3 Accessories security device 76288 01 Auxiliary Display PAD7 Printer Thermal STP 103 Printer Impact CBM 910 or SRP275 Cable Kit STP 103 8025258 Cable Kit CBM 910 8025257 Data collection Software SW12 Ohaus Collect 80500746 Test Equipment Depot 800 517 8431 99 Washington Street Melrose MA 02176 TestEquipmentDepot com PAJ N Series EN 8 7 TECHNICAL DATA Ambient conditions The technical data is valid under the following ambient conditions Ambient temperature 10 C to 30 C Relative humidity 15 to 80 9o at 31 C non condensing decreasing linearly to 50 at 40 C Height above sea level Up to 2000 m Operability is assured at ambient temperatures between 5 C and 40 C Power AC adapter Balance power input 8 14 5 VAC 50 60Hz 4VA or 8 20 VDC 4W Protection Protected against dust and water Pollution degree 2 Installation c
6. c printing Content CORE ERE The content in the data transmission can be modified Each of the following settings can be set on or off Number Only auf WbEr will only send the numeric result Balance ID bRt td will add the Balance serial number for traceability purposes Reference rEFEx will add reference information relevant to the current mode GLP GLP will send additional items to allow proper documentation of laboratory results Line Format t E Fo Single line format 5 4SLE will put all the data in one line separating each output with a comma Multi line format Putt will put each data output on a new line Multi 4 PQ 4LF will add 4 line spaces between each output PAJ N Series EN 6 AAAAANAAANAANAAAAAAAAAAANANANA User ID n GLP ON Bal ID 123456789 Balance ID ON Proj ID GLP ON TIme i oisi GLP ON Date T D owes GLP ON 120 01 g Result Multi Line Format with 4 line feeds Line Feed 2 _____ Line Feed 3 Line Feed 4 AAAAAAAAAAAAAANAAAAAAA 4 7 RS232 Menu 5232 Baud bRud The RS232 baud rate can be set to 600 1200 2400 4800 9600 and 19200 Parity PAr 4 Parity can be sent to 7 bits even parity 1 EUER 7bits odd parity 1 edd bits no parity 1 fla or 8bit no parity 8 fo Handshake HAndSh Handshake can be set fo off SEE GFF X on X off on oFF or hardware HArdbur 4 8 Lock Menu LGC When a Lock Menu item is set on th
7. e indicated menu cannot be changed Loc CAL Calibration menu lock Loc SEE Setup menu lock Loc P lod Mode menu lock Loc Un E Unit menu lock Loc Prt Print menu lock Loc 232 RS232 menu lock 9 0 LEGAL FOR TRADE When the balance is used in trade or legally controlled applications it must be set up verified and sealed in accordance with local weights and measures regulations It is the responsibility of the purchaser to ensure that all pertainent legal requirements are met 5 Settings Before the verification and sealing perform the following steps 1 Verify the menu settings meet the local weights and measures regulations 2 Perform a calibration as explained in Section 2 5 3 Set the position of the security switch as shown in Section 5 3 Note When the security switch is set on the following menu settings cannot be changed CAL SETUP MODE UNIT and LOC 5 2 Verification The local weights and measures official or authorized service agent must perform the verification procedure 5 3 Sealing Access to the Balance Settings The local weights and measures official or authorized service agent must apply a security seal to prevent tampering with the settings Refer to the illustrations below for the sealing methods emp Om Un Locked Locked with Paper Seal Locked with Wire Seal EN 7 PAJ N Series 6 0 MAINTENANCE 6 1 Troubleshooting Unstable environment Move balance to suitable location Incorrect calibr
8. in grams PAJ N Series EN 10 7 4 Compliance Compliance to the following standards is indicated by the corresponding mark on the product CAN CSA C22 2 No 61010 1 04 UL Std No 61010A 1 FCC Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Industry Canada Note This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada ISO 9001 Registration In 1994 Ohaus Corporation USA was awarded a certificate of registration to ISO 9001 by Bureau Veritus Quality International BVQI confirming that the Ohaus quality management system is compliant with the ISO 9001 standard s requirements On May 15 2003 Ohaus Corporation USA was re registered to the ISO 9001 2000 standard LIMITED WARRANTY Ohaus products are warranted against defects in materia
9. l models Calibration Adjust CAL Adu allows adjustment to the result of the internal calibration by 99 divisions InCal models only 4 3 Setup Menu SE amp uP Filter F Wt Use the low setting SET LO when environmental disturbances are not present Use the medium setting SET MED for normal environments Use the high setting SET HI when vibrations or air currents are present Auto Tare R ER E The initial item placed on the balance is assumed fo be a container so it is zeroed out The next item is then weighed When the pan is cleared the balance resets waiting for a container SET OFF SET ON Local weights and measures authorities may require that Auto Tare be disabled Global Reset GbL x St Resets all settings to factory default values RESET 4 4 Mode Menu P odE Count Mode Count SET ON SET OFF Average Piece Weight APW Optimization RPuJ OP 1 SET ON SET OFF 4 5 Unit Menu Un amp The Unit menu is used fo enable or disable a specific unit SET ON SET OFF The unit is indicated by a small character next to Unit in the display g 2 grams 4 6 Print Menu Pr t Auto Print A Pr wt Data will be continuously sent when font mu is set Interval int Er sends data every 1 to 3600 seconds When Stable SERbLE will send data when the balance detects a new stable reading This can be a weight value only tGRd or it can also include a stable zero t 42 amp ro GFF disables automati
10. ls and workmanship from the date of delivery through the duration of the warranty period During the warranty period Ohaus will repair or at its option replace any component s that proves to be defective at no charge provided that the product is returned freight prepaid to Ohaus This warranty does not apply if the product has been damaged by accident or misuse exposed to radioactive or corrosive materials has foreign material penetrating to the inside of the product or as a result of service or modification by other than Ohaus In lieu of a properly returned warranty registration card the warranty period shall begin on the date of shipment to the authorized dealer No other express or implied warranty is given by Ohaus Corporation Ohaus Corporation shall not be liable for any consequential damages As warranty legislation differs from state to state and country to country please contact Ohaus or your local Ohaus dealer for further details Test Equipment Depot 800 517 8431 99 Washington Street Melrose MA 02176 TestEquipmentDepot com
11. ner 3 2 Count Mode Use the Count mode to count parts of uniform weight To access Count Mode press Unit until the display shows Count Establish an Average Piece Weight APW Each time a new type of part is to be counted the nominal weight of one piece APW must be established using a small quantity of pieces With CL c RPuJ displayed press No to use the previously saved APW or press Yes to establish a new APW The display indicates the number of pieces to be used to establish the new APW If a different sample size is preferred press No until the desired sample size is displayed 10 20 50 or 100 Put the specified number of pieces on the pan Press Yes to accept new APW or No to abort Count Place the quantity to be counted on the pan APW Optimization Since the weight of each piece varies slightly APW Optimization may be used to increase PAJ N Series EN 4 the accuracy of the count The balance automatically recalculates the Average Piece Weight when the number of parts on the pan is less than three times the original sample size The display shows APuJ gP 7 each time the APW is optimized 3 4 Weigh Below Feature e Ec ry N A r Remove Weigh Below Cover Attach wire or string to Hook Suspend sample 4 SETTINGS 4 1 Menu Navigation gt A PRINT CONTENT PARITY setup L J END MOD KILOGRAM uNEFO HAND SH MODE O
Download Pdf Manuals
Related Search