S800 User Manual en
Contents
1. Make sure to mount the IMU module at the IMU position first O Mount the GPS with a bracket to avoid interference from center frame power board Ensure the USB port of the M C outwards for easy access O Please wire neatly Make sure wires will not be cut by the edge of frames Tips O Install screws with appropriate strength to prevent damage threads Mount Frame Arms Step 1 B00CF xt Copper contacts H 800FA x6 Propeller i Screw H Cover i Motor i Renae ESC Motor rotation direction LED A A Clock wise i GAO Counter clock wise i Green H 800CF x1 x1 800FA x6 x6 Horizontal Step1 Check arms 1 Make sure copper contacts are in good condition without bend or severe wear 2 Make sure propellers are without crack and screws in propeller cover tight 3 Make sure motors are mounted firmly and rotate freely 4 Distinguish LED indicator on the ESC bottom With a red point in is red LED others are green LED We recommend you mount arms with red LED to M1 and M2 5 Distinguish marks and onthe arms Arm gt Center frame Arm gt Center frame Step2 Insert frame arm into center frame vertically Step3 Slowly rotate the frame arm upward until positioned completely Step4 Press down the buckle to lock the arm Make sure the arm does not move Step5 Make sure the buckle is pressed down correctly about 35 under normal circumstan2. as shim mount position of arm is different from am Tips e Please use adequate screw glue e Install screws with appropriate strength 15 chji Spreading Wings S800 2012 Dajiang Innovation Technology Co Ltd All Rights Reserved 6 F HKUST SZ IER Building No 9 Yuexing 1st Rd South District Hi Tech Park Shenzhen 518057 Guangdong China Tel 86 755 2665 6677 Sales ext 201 202 203 Fax 86 755 83067370 Service hotline 86 755 22673777 Sales sales dji innovations com Technical support support dji innovations com Others info dji innovations com DJI Spreading Wings is registered trademark of Dajiang Innovation Technology Co Ltd Names of product brand etc appearing in this manual are trademarks or registered trademarks of their respective owner companies This product and manual are copyrighted by Dajiang Innovation Technology Co Ltd with all rights reserved No part of this product or manual shall be reproduced in any form without the prior written consent or authorization of Dajiang Innovation Technology Co Ltd No patent liability is assumed with respect to the use of the product or information contained herein 16
3. 2050 ni ee ta senj oka dai ej la le 6 Mount Center Frassi tia a E Le eee 7 Mount Frame AriMS 22 ie si incest i TA dk 8 Mount Bis oo m rider da cr 10 ASSAM D a 00 oko oi eae ab ah bl 12 ESC Sound aiii ai nie a Bini ee i ine E a da 13 Specification da pi Oe iodo 13 APppendi renni ann Ni id ota 15 Product Usage Cautions When flying the fast rotating propellers of S800 may cause serious damage s and injuries Therefore please fly with a high safety in mind at all time Mount Attention Mount GPS with a bracket to avoid interference from the power board of center frame For IMU position make sure the arrow direction marking is pointing to the aircraft nose Mount the arms correctly Center frame Arm Center frame O gt ArmO For removing screws in the bottom board please proceed with cautious avoiding damages Do not remove any other screws fixed with glue Notice matching the indications is very important please pay attention to them Flight Attention e Keep flying multi rotor a distance from people building high voltage lines etc e Do not get close to or touch the working motors and propellers which will cause serious injury e Do not over load the multi rotor Make sure the propellers and the motors are installed correctly and firmly before flying Make sure all parts of S800 are in good condition before each flight Do not fly with wore or broken parts e Strongly recommend you use DJI parts
4. as much as possible Others e if you have any problem you cannot solve please contact agents or DJI customer service In Box Center Frame 800CF 800FA Frame Arm 800TF 800AR x2 T Frame x2 Aluminum Ring y Base Pipe 800BPIx2 Bi pod Drawbar 800BD x4 a re Silicone Rubber Damper BOOSRD x4 Nonslip Damper 800ND x4 ap HJ JH 3 PIN Servo Cable B00SC x1 Screw Package B00SP x1 Hexagonal screws M2 5x5 Hexagonal socket head cap screws HC M2 5x5 HC M2 5x8 HC M3 0x22 Adhesive Velcro BOOAV x1 Battery Band Tools Needed 2 0mm Hex Wrench 2 5mm Hex Wrench Screw Glue Nylon Cable Tie Scissors Diagonal Cutting Pliers Foam Double Sided Adhesive Tape 800BB 600SSP 1 x2 Spare Screw Package For mounting screws For fastening screws For binding devices and wires For fixing receiver controller and other modules Center Frame Wiring The top board is power distribution board and the bottom board is for loading autopilot system components Top Board Mark Motor clock wise Mark Motor number XT60 Female To Gimbal ESC signal outlet To main controller Circuit line Parallel LS Mark Motor count clock wise IMU mount positi
5. ESCs are specially designed for multi rotors When use with DJI autopilot systems you do not have to setup any parameters or calibrate travel range Specifications Frame Diagonal Wheelbase Frame Arm Length Frame Arm Weight Including Motor ESC Propeller Center Frame Diameter Center Frame Weight 800mm 350mm 304g 240mm 365g Bi pod Size 500mm Length x415mm Width x320mm Height Top width 145mm Bi pod Weight 4289 Total Weight 2 6Kg Motor Stator Size 41x14mm KV 320rpm V Max Power 360W Weight 1479 13 ESC Current 40A OPTO Voltage 6S LiPo Signal Frequency 30Hz 450Hz Drive PWM Frequency 24KHz Weight 189 Propeller Material Carbon Fiber Size 15x04in Weight 159 Flight Parameters Takeoff Weight 5 0Kg 7 0Kg Load Weight OKg 2 5Kg Power Battery Max Power Consumption Hover Power Consumption Hover Time LiPo 6S 10000mAh 15000mAh 15C Min 2100W 720W Takeoff Weight 6Kg Max 16 min 10000mAh amp 6KgTakeoff Weight 14 Appendix Step1 For arms For arms WI YZIZA lt TA Gure N LJ Step2 Motor mount screws Step3 For arms For arms Step1 Remove Please unscrew the screws on the top Step2 Tighten Retighten the motor mount screws on the back to make the motor firmly attached Step3 Remount Remount the screws on the top Notices Shim should be mounted in the correct position
6. Spreading Wings S800 User Manual V 1 0 ciji www dji innovations com 1 Disclaimer Read this disclaimer carefully before using Spreading Wings S800 By using this product you hereby agree to this disclaimer and signify that you have read them fully Spreading Wings S800 is an excellent multi rotor With a good autopilot it will offer tremendous flight features Despite the controller of DJI autopilot operate in the safest manner when the main power battery is connected we strongly recommend customers to remove all frame arms and keep children away during system calibration and parameter setup Dajiang Innovation Technology Co Ltd DJI assumes no liability for damage s or injuries incurred directly or indirectly from this product usage S800 Profile DJI Spreading Wings S800 is a multi rotor designed for AP It simplifies users installation and enables quick disassembling Frame arm integrates with ESC and motor With DJI WKM autopilot system it can achieve hovering cruising and other flight elements S800 can be applied for aerial photography and other aero modeling activities 350mm Lenghth a e VAIS Contents DISGIAIMEr e a o ali ke Sagan E dabra Ri AA EEK 2 5800 Profil lt teh hd tata T nalts ted EL SK 2 GontentS ia die deidad 3 Product Usage Cautiva ee 4 A i ji aaa S io a a A eia i E 5 Tools Needed en a oo cere ee cea o tetas A este degree A 5 Genter Frame Wiring
7. ces Notices Please add some lubricant at the position 1 if it is hard to press down the buckle Slowly rotate the frame arm to prevent from breaking the copper contacts Please refer to 2 to ensure the arm is perfectly positioned Make sure use appropriate strength to press down the buckle correctly Do not hot plug arms If the motor mount become loosens please tighten it by following the procedures in Appendix Tips e LED is on after motor start Examination Arms are aircraft nose direction arms are aircraft tail See from top motors on arms O rotate counter clockwise motors on arms rotate clockwise Mount Bi pod Step1 800TF 800BP 800SRD 800ND Step3 HC M2 5x8 x4 HC M3 0x22 x2 H frame bulges outwards MT frame notch Step1 Mount T frame 800TF and base pipe 00BPI 1 Put nonslip damper 800ND through the base pipe 2 Put the base pipe into T frame until the head of nonslip damper is embedded into T frame 3 Embed the other nonslip damper into the T frame 4 Put silicon rubber damper 800SRDj onto both sides of the base pipe Step2 Mount H framelB00HF and bi pod drawbars B00BDI 1 Fix but not tighten hexagonal socket head cap screws HC M2 5x5 Fig to H frame and bi pod drawbar Fig 2 Adjust drawbar and T frame and fix but not tighten hexagonal socket head cap s
8. crew 10 HC M2 5x5 Fig 2 to drawbar and aluminum ring 800AR Step3 Mount H frame and T frame 1 Insert T frame through aluminum ring until it plugs into H frame 2 Fix T frame notch into H frame bulges outwards make sure T frame will not move 3 Put the bi pod on the flat floor to adjust H frame and T frame 4 Tighten all hexagonal socket head cap screws including and 2 Notices e Putbi pod on the flat floor to finish mounting smoothly and correctly Please mount the screws and use adequate screw glue Separate the bi pod by disconnecting the H frame to make for easy carriage Completed Quick Disassembly 11 Assembly Assembly Align knob to mark Insert knob into arm Rotate knob Step1 Align all knobs on the H frame to the marks refer to fig 1 Step2 Lie frame and bi pod horizontally insert knobs into arms and first and then adjust to insert others into the arms Step3 Rotate the knob to the end as fig 2 shown Notices e Ensure all knobs on the H frame aligned to the marks and they would go through the arms successfully Tips e Itis convenient for you to carry S800 by quick disassembly Frame Bi pod Frame and Bi pod 12 ESC Sound ESC State Ready Throttle stick is not at bottom Input signal abnormal Input voltage abnormal Tips Sound 11234567 BBBBBB Be Baat B BB BB BB BB DJI
9. on Notices e For IMU position make sure the arrow direction marking is pointing to the aircraft nose e Connect the motor 3 pin connector M1 M6 from WKM M C to ESC signal socket M1 M6 on center frame markings accordingly WKM M C M1 ESC signal socket M1 WKM M C M6 ESC signal socket M6 Tips e Main battery power leads gimbal and PMU leads are on the bottom surface of the top board e Markings and stand for the propeller rotation direction means clock wise and means counter clock wise e f you need other lead connector please cut the original connector and solder on the new connector But not Recommena Mount Center Frame Remove Screws Fix Screws 800CF M2 5 5 x1 x19 Step1 Mount IMU module into IMU position in the center frame Ensure IMU casing is out of touch the top board edge as vibration can cause IMU mal function Step2 Please mount DJI Autopilot System parts onto the bottom board not including GPS modules Please remove all the screws from the bottom board first if necessary Step3 Connect Autopilot System and receiver Please refer to DJI WKM User Manual for details Step4 Please mount the screws to bottom board and use adequate screw glue Step5 Mount the GPS on the top board with a bracket Step6 Configure Autopilot System Please refer to DJI WKM User Manual Notices
Download Pdf Manuals
Related Search