2010 300 332 0 MBA Modell M04, M11 CM en - Becker
Contents
1. What to do if Problem Cause Remedy The roller shutter curtain is raised un 1 One or more attachments have Repair system then reset the limit posi evenly or not at all broken off tions 2 Lath has broken off Tubular drive stops arbitrarily cannotbe Roller shutter curtain keeps sticking too Repair system restarted in the same direction much friction Tubular drive does not run in the right dir Electrical connection faulty Check the electrical connection ection BECKER ie Sample wiring diagrams Control via a single switch button Central group and individual control using Centronic UnitControl UC42 L1 NPE i Mains 230 V 50 Hz contol uit Central Central cable 1 NIL ALY 230 V 50 Hz connection to further control units gt i gt Group 230 V 50 Hz L Individual Individual UC42 UC42 i a L i Z M 2 4 M l ASIAAN eee tt Ini Ich ft LI 230 V 50 Hz LI 230 V 50 Hz Declaration of conformity BECKER ANTRIEBE GMBH Friedrich2. BECKER W BECKER 1 2010300332 0g 11 08 2015 s BECKER
3. The drive does not achieve its full duty cycle until it has cooled to ambient temperature Avoid a situation where the thermal protection switch cuts in repeatedly Information for the electrician The tubular drives with mechanical limit switching must not be connected in parallel The drive manufacturer offers a range of suit able controls for the simultaneous control of several drives Use external conductor L1 to control the up and down direction Other devices or consumers lamps relays etc must not be dir ectly connected to the drive connecting cables For this purpose the drives and additional devices must be decoupled by relay controls When installing the drive all pole disconnection from the mains with a contact gap of at least 3 mm per pole must be provided EN 60335 Attention Only use mechanically or electrically locked switching elements with a marked zero posi tion This also applies when drives with electronic and mechanical limit switching are used in the same system The changeover time for switching the running direction must be at least 0 5 s The switch and control must not execute simultaneous UP and DOWN com mands Protect the electrical connections from damp Once you have finished wiring everything to the control ALWAYS check the right direction assignment of the drive to the control buttons UP and DOWN EXTEND and RETRACT If the drive is to be operated with devices which contain sources
4. Ebert Str 2 4 Se BECKER 35764 Sinn Germany Original EC Declaration of Conformity Document No Month Year K001 02 15 We hereby declare that the following product series Product designation Tubular motor Type designation R4 17 R8 17 R12 17 R15 17 R20 17 R25 17 R30 17 R40 17 R50 11 R40 17 37 Nm R7 17 P9 16 P5 30 P5 20 P13 9 P5 16 P4 16 P3 30 L44 14 L50 11 L50 17 L60 11 L60 17 L70 17 L80 11 L80 17 L120 11 Version C M HK R S F P E O SMI A0 Z9 mute From serial number from 150800001 complies with the applicable regulations of the following Directives Machinery Directive 2006 42 EC Electromagnetic Compatibility 2004 108 EC Furthermore the safety objectives of the Low Voltage Directive 2006 95 EC as per Appendix No 1 5 1 of Directive 2006 42 EC have been met Applied harmonised standards EN 60335 1 2012 EN 60335 2 97 2010 EN 61000 6 1 2007 EN 61000 6 3 2007 EN 14202 2004 Authorised party for the compilation of the technical documentation Becker Antriebe GmbH Friedrich Ebert Str 2 4 35764 Sinn Germany This declaration of conformity was issued Sinn 12 02 2015 PP tan Place Date D Fuchs Management This declaration certifies compliance with the Directives cited but does not represent any assurance of characteristics The safety warnings in the supplied product documentation must be observed
5. mm 47 Emission sound pressure level dB A lt 70 Model R30 M04 R40 M04 R50 M04 R30 M11 R40 M11 Type R30 17C M R40 17C M R50 11C M Rated torque Nm 30 40 50 Output speed rpm 17 17 11 Limit switch range 38 revolutions Supply voltage 230 V AC 50 Hz Connected load W 205 260 240 Rated current consumption A 0 90 1 15 1 10 Mode S2 4 min Degree of protection IP 44 Min tube inside diameter mm 47 Emission sound pressure level dB A lt 70 Technical data dia 58 Model L50 M04 L50 M04 L60 M04 L60 M04 Type L50 11C M L50 17C M L60 11C M L60 17C M Rated torque Nm 50 50 60 60 Output speed rpm 11 17 11 17 Limit switch range 36 revolutions Supply voltage 230 V AC 50 Hz Connected load W 235 315 265 380 Rated current consumption A 1 05 1 40 1 20 1 75 Operating mode S2 4 min Degree of protection IP 44 Min tube inside diameter mm 60 Emission sound pressure level dB A lt 70 Model L70 M04 L80 M04 L80 M04 L120 M04 Type L70 17C M L80 11C M L80 17C M L120 11CM Rated torque Nm 70 80 80 120 Output speed rpm 17 11 17 11 Limit switch range 36 revolutions Supply voltage 230 V AC 50 Hz Connected load W 430 310 470 435 Rated current consumption A 1 90 1 40 2 10 1 90 Operating mode S2 4 min Degree of protection IP 44 Min tube inside diameter mm 60 Emission sound pressure level dB A lt 70 This tubular drive is not yet available
6. P5 L120 Model M04 M04s M11 Gi Assembly and Operating Instructions Roller shutter and sun protection drives with mechanical limit switch Important information for Fitters Electricians Users Please forward accordingly These instructions must be kept safe for future reference Becker Antriebe GmbH Friedrich Ebert StraBe 2 4 sr onto BECKER www becker antriebe com Table of contents Generali aaa alata 3 Warranty arnie aa ari ii 3 SAfeivinsiruclions ssa uao 4 Instructions for the USET nsise na N ioni a Aaa lena 4 Instructions for installation and commissioning eea a ER A Ee EE T E EE E E 4 Intended USE sdara ia E ARR RE ORA re EA EEEa 6 Assembling and disassembling the plug in connecting cable i 6 Assembling the plug in Connecting cable asic ve esau tenner feanceccees apeaidccnas ae aan ia roi aoe 6 Disassembling the plug in connecting cable for tubular drives dia 35 ee 7 Disassembling the plug in connecting cable for tubular drives dia 45 and dia 58 e 8 iNstallatioit risanii riali ai ia E A VE RE 8 Assembling the ALIVE ARTISAN tac age n i whe 8 Undoing the MOUNTING Pinner clic ia dalai lipidi leali ipa 9 Assembling the drive adapter with drive adapter safety catch e 9 Assembling the drive adapter with screw connection e 9 Securingthe drive against axialdisplaC Menti cile A Raineri 9 Fixing
7. and dia 58 Size of drive Diameter of barrel Torque Fastening screws mm mm max Nm for drive adapter 4 pc dia 35 40 mm plastic drive adapter 13 Self tapping screw dia 4 8 x 9 5 mm dia 45 50 70 mm plastic drive adapter 25 Self tapping screw dia 4 8 x 9 5 mm dia 45 50 85 mm plastic drive adapter 40 Self tapping screw for obstacle detection dia 4 8 x 9 5 mm dia 45 50 85 mm diecast drive adapter 50 Self tapping screw dia 4 8 x 9 5 mm dia 58 85 133 mm aluminium drive adapter 120 Countersunk screw M8 x 16 mm dia 58 63 120 mm diecast drive adapter 120 Self tapping screw dia 6 3 x 13mm We also recommend screwing the idler to the barrel Attention Do not hammer the tubular drive into the tube or drop it into the barrel The curtain can only be secured using springs or anti lifting devices Mounting the drive in the tube For profile tubes In the case of some drive adapters tolerances of the groove widths in different bar rels can be offset by rotating the drive adapter into a different groove recess These groove recesses have different sizes and allow the drive to fit exactly For round tubes First notch the tube on the motor side so the lug of the thrust ring can also be pushed into the tube There must be no play between the lug of the thrust ring and the tube 58mm Assemble the tubular drive with th
8. avoid damage to property ATTENTION Denotes user tips and other useful information Warranty Structural modifications and incorrect installation which are not in accordance with these and our other instructions can result in serious injuries e g crushing of limbs Therefore structural modifications may only be carried out with our prior approval and strictly in accordance with our instructions particularly the information contained in these Assembly and Operating Instructions Any further processing of the products which does not comply with their intended use is not permitted The end product manufacturer and fitter have to ensure that all the relevant current statutory official and in particular EMC regu lations are adhered to during utilisation of our products especially with regard to end product manufacture installation and cus tomer advice BECKER 3 Safety instructions The following safety instructions and warnings are intended to avert hazards and to prevent property damage and personal injury Instructions for the user General information e All work including maintenance and cleaning on electrical installations as well as other system parts must always be performed by authorised specialists in particular qualified electricians Children from the age of 8 years and persons with reduced physical sensory or mental capabilities or lack of experience and or knowledge may use these d
9. d brackets must be fitted The tubular drive presses the closed curtain down to make it difficult for people to reach under it or raise it Only use curtains made of sufficiently strong material such as aluminium steel or wood To prevent damage to the curtain it must run in guide tracks from top to bottom Undoing the mounting pin When pushed in the mounting pin 2 locks automatically To undo the mounting pin 2 push the tab washer 1 upwards and pull out the mounting pin 2 ION Pa lt p gt Put the drive adapter 1 onto the drive shaft of the tubular drive You can see which way to insert the safety catch 2 from its shape When inserting the drive adapter safety catch 2 into the hole 4 make sure that the locking lug 3 engages You will hear a click Check that the safety catch is securely in position by pulling on the drive adapter 1 Put the drive adapter 1 onto the drive shaft of the tubular drive For the assembly use an M6 x 12 screw 3 with appropriate washer 2 and suitable screw retainer Threaded hole 4 Securing the drive against axial displacement In order to secure the drive against axial displacement we recommend screwing the drive adapter to the tube sl 10 mm Attention When drilling into the barrel never drill near the tubular drive Fixing the drive adapter to the barrel dia 35 and dia 45
10. e relevant thrust ring 1 and drive adapter 2 In sert the tubular drive with the pre assembled thrust ring and drive adapter into the tube to achieve a form fit Ensure that the thrust ring and drive adapter are secure in the tube Mount the assembled unit comprising barrel tubular drive and idler on the box and secure the drive with a split or spring pin ac cording to the type of wall bracket fixing The drive can be operated either with the switch Item no 4901 001 158 0 or the op erator control provided Connect the pigtail wires of the tubular drive to those of the same colour in the switch lt gt or operator control and switch on the power supply Check the direction of travel If the direction of travel of the shading solution does not correspond to the operator control swap the black and brown pigtail wires of the tubular drive Attention The switch is not suitable for continuous operation and has only been designed for start up When using springs anti lifting devices we recommend you use at least three for longer tubes use three springs anti lifting devices per metre of barrel fino Lay the connecting cable Lay the connecting cable up to the tubular drive and fix The connecting cable and any antennae must not project into the winding chamber Cover any sharp edges BECKER li Sett
11. e same type of mains connecting cable which is available from the drive manufacturer Attention Safety instructions for avoiding property damage Ensure that there is adequate clearance between moving parts and adjacent objects The drive must not be carried by the mains connecting cable All latching connections and fastening screws on the brackets must be checked to en sure that they are secure Ensure that nothing rubs against the tubular drive such as shading solution attach ments screws etc 5 Intended use The type of tubular drive described in these instructions is intended solely for the operation of roller shutters and sun protection systems We recommend using drives with more than 17 rpm only in sun protection systems screens When mounting connection parts on the drive PXX XX dia 35 mm only use screws EJOT Delta PT 40x12 WN 5454 Torx 9900 000 545 4 This type of tubular drive is designed for use in single systems one drive per barrel The tubular drive must not be used in potentially explosive areas The connecting cable is not suitable for transporting the drive Always carry the drive by the housing tube Other applications uses and modifications are not permitted in order to protect the safety of the users and others since these ac tions can impair the system s safety and carry the risk of personal injury and property damage The drive manufacturer does not accept liability for damages or
12. evices provided they are supervised or have been instructed in the safe use of the device and have understood the hazards involved Children must not play with the device e Systems have to be checked regularly by authorised specialists for wear and damage Always put damaged systems out of operation immediately until they are repaired by an authorised specialist e Do not operate equipment if people or objects are within the danger zone Observe the danger zone of the equipment during operation e Stop and disconnect the equipment from the mains power supply when maintenance and cleaning is being performed either on the system itself or in the immediate vicinity of it Ensure that there is adequate clearance at least 40 cm between moving parts and adjacent objects Caution Safety instructions for avoiding serious injuries e Crushing or shearing points must be avoided or protected Instructions for installation and commissioning General information e Observe the safety instructions in EN 60335 2 97 Please note that this list of safety instructions is not exhaustive since it would be impossible for the standard to include all sources of danger For example the design of the operated product the way the drive works in the situation it is installed in or even the way the end product is mounted in the end user s place of use cannot be taken into consideration by the drive manufacturer If any questions or uncertainties regard
13. fter commissioning the limit positions must be correctly set programmed in Drives with a HO5VV F connecting cable may only be used indoors Drives with a HO5RR F SOSRN F or 05RN F connecting cable may be used both indoors and outdoors To connect the drive to the driven part solely mechanical accessory components made by the drive manufacturer from the current product catalogue may be used The components must be installed in accordance with the manufacturer s instructions If the drive is used for shading solutions in a specially marked area e g escape routes hazard zones safety areas compliance with all applicable regulations and standards must be ensured Caution Safety instructions for avoiding serious injuries When electrical or electronic equipment and units are operated certain components e g the power supply unit are live Physical injuries or damage to property can result in the event of unauthorised interventions or failure to heed warnings Be careful when touching the tubular drive as it heats up during operation for technolo gical reasons Before installation shut down all lines and control devices that are not essential for op eration Crushing or shearing points must be avoided or protected When installing the drive all pole disconnection from the mains with a contact gap of at least 3 mm per pole must be provided EN 60335 If the drive mains connecting cable is damaged it must be replaced with th
14. ght into the recess of the locating latch so that the latch releases the locating lug from the plug Now you can pull out the connecting cable along with the flathead screwdriver dia 45 and dia 58 C plug A locating latch Installation Assembling the drive Attention To connect the drive to the driven part solely mechanical accessory components made by the drive manufacturer from the current product catalogue may be used Prior to mounting the fitter must ensure that the masonry and the system being motorised are sufficiently robust drive torque plus weight of the shading solution Caution Electrical connections may only be carried out by a qualified electrician Prior to assembly the power supply must be disconnected and secured Please give the enclosed connection information to the responsible electrical contractor Calculate the space required at the side M by measuring the drive head and wall bracket The clear dimension of the box X minus the space required at the side M and idler G gives the length L of the barrel L X M G The space required at the side M varies depending on the combination of drive and wall bracket Then mount the wall bracket and idler Ensure that the barrel is aligned at right angles to the wall and that sufficient axial play is al lowed for the mounted system Attention When using anti lifting devices close
15. ing the limit positions E Upper limit position Fd Lower limit position EO I IE Lower limit position PA Upper limit position S 7 a D Setting the lower limit position 1 Before the shading solution is fixed to the barrel let the drive run DOWN until it switches off automatically 2 By adjusting the lower limit position position the barrel to make it easy to fix the shading solution to the barrel Setting the upper limit position Activate the UP switch The drive rolls up the shading solution Extend or reduce the range of travel by turning the corresponding set screw Note on roller shutter use 1 To make allowances for any changes in the length of the roller shutter do not mount mech anical stops Make sure that the individual laths cannot shift sideways During commissioning and subsequent use ensure that the roller shutter curtain runs UP and DOWN smoothly and easily Test for proper functioning As a final check run the shading solution to the limit positions in both directions again Attention The tubular drives are designed for short time operation for the operating mode please see technical data An inbuilt thermal protection switch prevents overheating of the tubu lar drive During commissioning long drop distance or long running time the ther moswitch may trigger The drive will switch off After a short cooling down period the sys tem is ready for operation again
16. ing the safety instructions contained in the standard arise please contact the manufacturer of the part or end product in question All applicable standards and regulations for electrical installation must be complied with e All work including maintenance and cleaning on electrical installations as well as other system parts must always be performed by authorised specialists in particular qualified electricians e Only use spare parts tools and accessory devices which have been approved by the drive manufac turer Unapproved third party products or modifications to the system and its accessories represent a risk to your safety and the safety of others This means that the use of unapproved third party products or modifications which have not been agreed with or approved by us are prohibited We do not accept li ability for damage or injury arising from such actions e Position control devices within sight of the driven product but away from moving parts at a height of over 1 5m Permanently mounted control devices must be positioned where they can be seen e Rated torque and duty cycle must be suitable for the requirements of the driven product Technical data rated torque and service life can be found on the type plate of the tubular drive Moving parts of drives must be installed at a height of over 2 5 m above floor level or any other surface from which access to the drive is gained To ensure safe operation of the system a
17. injury arising from such actions Always observe the information in these instructions when operating or repairing the system The drive manufacturer does not ac cept liability for damage or injury resulting from improper usage Assembling and disassembling the plug in connecting cable Assembling the plug in connecting cable Insert the dead connecting cable into the drive head until the locating lug clicks into place in the drive If necessary use a suitable flathead screwdriver to assist with insertion Set the screwdriver into one of the two plug grooves provided for this purpose Check that the cable is properly engaged C plug ym 3 1 locating lug Disassembling the plug in connecting cable for tubular drives dia 35 Caution Prior to disassembly the power supply to the connecting cable must be disconnected On drives with a diameter 35 insert a suitable flathead screwdriver between the locating lug and the snap in pin so that the snap in pin releases the locating lug from the plug Now you can pull out the connecting cable along with the flathead screwdriver 235 C plug A snap in pin BECKER 7 Disassembling the plug in connecting cable for tubular drives dia 45 and dia 58 Caution Prior to disassembly the power supply to the connecting cable must be disconnected On drives with a diameter 945 or 58 insert a suitable flathead screwdriver ri
18. of interference the elec trician must ensure suitable interference suppression for the relevant devices Disposal This product is made of various materials which must be disposed of properly Find out about the applicable regulations on recyc ling or disposal for this product in your country The packaging material must be disposed of properly Maintenance These drives are maintenance free Technical data dia 35 Model P5 M04 P5 M04s P9 M04 P13 M04 Type P5 20C M P5 30C M P9 16CM P13 9C M Rated torque Nm 5 5 9 13 Output speed rpm 20 30 16 9 Limit switch range 38 revolutions Supply voltage 230 V AC 50 Hz Connected load W 115 115 110 115 Rated current consumption A 0 47 0 47 0 47 0 47 Mode S2 4 min Degree of protection IP 44 Min tube inside diameter mm 37 Emission sound pressure level dB A lt 70 13 Technical data dia 45 Model R8 M04 R12 M04 R20 M04 R12 M11 R20 M11 Type R8 17CM R12 17CM R20 17CM Rated torque Nm 8 12 20 Output speed rpm 17 17 17 Limit switch range 38 revolutions Supply voltage 230 V AC 50 Hz Connected load W 100 110 160 Rated current consumption A 0 45 0 5 0 75 Mode S2 4 min Degree of protection IP 44 Min tube inside diameter
19. the drive adapter to the barrel dia 35 and dia 45 and dia 58 e 10 MOUNTING TNS Civ ntMe4UD6 iro iaia pa ara iii fa 10 Setting th limit POSION S er neeese ia i a 12 informationiforthe electriciati ueiaa afelio a ia 13 Disposal rarasaan n RAI LR A o Sani 13 Ma intenanCE sseni nn ii alia ic ea iii dio 13 Technicalidata dia 395 ee ea lion lo ariete ir 13 Technicalidata dia 45 oila ail AR rei esa 14 Technicalidata dia Burgio ana ea ariani AEREA NI TI a a 14 Wiotodoi ea ii 15 iSamplewiring diagramSi i lire e ee earn il 16 Declaration Of CONTORMILY aria la ea rela 17 General These tubular drives are high quality products with the following features For use with roller shutters e For use with sunblinds Easy limit switch setting on the drive e Compatible with all of the drive manufacturer s control units for roller shutters and sunblinds For plug in connecting cable Please observe these Assembly and Operating Instructions when installing and setting up the equipment The date of manufacture comes from the first four digits of the serial number The numbers 1 and 2 indicate the year and the numbers 3 and 4 indicate the calendar week Example 24th calendar week in 2012 Ser No 1224XXXXX Explanation of pictograms CAUTION CAUTION indicates a hazardous situation which if not avoided could result in injury ATTENTION indicates measures that must be taken to
Download Pdf Manuals
Related Search