(HS3001ECH61H) for E6000 Emulator User`s Manual
Contents
1. O z Cable at is parallel lo user system E BY Cable head is parallel to user system User system 6 Figure 10 User System Interface Cable Location Example The JP1 jumper is used for testing Do not remove the jumper pin that is inserted in the sides of pin 1 and pin 2 16 Figure 11 JP1 Jumper RENESAS2. hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information When exporting the products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military including but not limited to the development of weapons of mass destruction Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations Renesas Electronics has used reasonable care in preparing the information included in this document but Re
3. or twisting the components Screws M2 x 12 mm with flat washers Cable head Pin 1 IC socket lt q 1C149 080 017 B5 manufactured by YAMAICHI ELECTRONICS Co Ltd User system Figure 3 Connecting User System Interface Cable to User System RENESAS 2 2 5 Fastening Cable Body Connect the cable body to the cable head Cable body Removing Push the remove jig User system Figure 4 Fastening Cable Body RENESAS 2 3 Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad footprint for the user system with an IC socket for an FP 80A package 1C149 080 017 B5 manufactured by YAMAICHI ELECTRONICS Co Ltd Note that the dimensions in figure 5 are somewhat different from those of the actual chip s mount pad 20 50 min El p aa 14 70 max gt j 19 12 35 0 1 lt 0 65 x 19 35 0 0 35 01 gt 0 65 0 05 0 05 E E y E 5 A E E Lo a ol H o Lo Sl Q o fa Al Il D x LO o E E E E E y E ll mn e Figure 5 Recommended Dimensions for Mount Pad RENESAS 2 4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6 Unit mm Tolerance 0 5 mm Figure 6 Dimensions for Use
4. user system RENESAS Contents Section 1 Condor ria ii 1 Section 2 Connection Procedures icpsy2ssconceatstiatsstaanseuedsarevaeyadeaoivsarcensrascanntin tobias 4 2 1 Connecting User System Interface Cable to Emulator Station 0 0 cece eeeeeseereeeeeneeeeee 4 2 2 Connecting User System Interface Cable to User System ooooocionnnononncnconcnncncnonananoninnon 6 22 Installing IC Socket icirniaianain aia iii 6 222 SOMETIME IC Socket inicia dada 6 22 3 Inserting Cable Head c cc ssascssscssessasevinssuessaesbasncnessvscsbessesnsansedonnasedaseaicesvensaces 6 2 24 Bastening Cable Head viii iii EEs a 7 2 23 Fastemng Cable BodYcioconcuisasniocio tic ca tc iones it deca 9 2 3 Recommended Dimensions for User System Mount Pad oooncnncnocnnccoccnonaconononnconcnnnnncnnnos 10 2 4 Dimensions for User System Interface Cable Head ooncoccncnncniccnonocnnonnonconcancnn cnn nanonononnnno 11 2 5 Resulting Dimensions after Connecting User System Interface Cable eee eeeeee 12 Section 3 Installing the MCU to the User SySteM ooooonnccnonccnononannnnncncnnncnoncnnnos 13 Section 4 Verifying Operation cdsssecscsesccerisarsansessavasensancendesesvownd aiii 15 SCHUON S INQUCO anita 16 ii RENESAS Section 1 Configuration CAUTION Use an 1C149 080 017 B5 socket manufactured by YAMAICHI ELECTRONICS Co Ltd for the FP 80A package IC socket on the user system Figure 1 shows the configuration of the HS3001ECH61H user system inter
5. To our customers Old Company Name in Catalogs and Other Documents On April 1 2010 NEC Electronics Corporation merged with Renesas Technology Corporation and Renesas Electronics Corporation took over all the business of both companies Therefore although the old company name remains in this document it is a valid Renesas Electronics document We appreciate your understanding Renesas Electronics website http www renesas com April 1 2010 Renesas Electronics Corporation Issued by Renesas Electronics Corporation http www renesas com Send any inquiries to http www renesas com inquiry ENESAS 8 10 11 12 Notice All information included in this document is current as of the date this document is issued Such information however is subject to change without any prior notice Before purchasing or using any Renesas Electronics products listed herein please confirm the latest product information with a Renesas Electronics sales office Also please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is granted
6. ain use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or system manufactured by you Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronic
7. ctly aligned The user system interface cable dedicated to the emulator must be used To connect the cable body to the emulator station follow the instructions below 1 Make sure the user system and emulator station are turned off 2 After making sure the direction of the cable body connector is correct firmly insert the cable body connector into the emulator station socket figure 2 RENESAS Emulator station Figure 2 Connecting User System Interface Cable to Emulator Station RENESAS 2 2 Connecting User System Interface Cable to User System A WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned Failure to do so will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST To connect the cable head to the user system follow the instructions below 2 2 1 Installing IC Socket After checking the location of pin 1 on the IC socket apply epoxy resin adhesive to the bottom of the IC socket for an FP 80A package and fasten it to the user system before soldering 2 2 2 Soldering IC Socket After fastening solder the IC socket for an FP 80A package to the user system Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder
8. face cable for the FP 80A package RENESAS la Y emulator station Cable body Screws M2 x 12 mm with flat washers for fastening cable head Screws M2 x 8 mm with flat washers G Cable head amp Socket cover pS E IC socket User system Figure 1 HS3001ECH61H User System Interface Cable RENESAS Table 1 lists the HS3001ECH61H components Please make sure you have all of these components when unpacking Table 1 HS3001ECH61H Components No Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the FP 80A package 4 Socket cover 1 For installing an FP 80A packaged MCU 5 Screws M2 0 x 12 mm 4 For fastening cable head with four flat washers 6 Screws M2 0 x 8 mm 4 For installing an FP 80A packaged MCU with four flat washers 7 Documentation 1 User s manual for HS3001ECH61H this manual 3 RENESAS Section 2 Connection Procedures 2 1 Connecting User System Interface Cable to Emulator Station A WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part Before connecting make sure that pin 1 on both sides are corre
9. fillets Use slightly more solder than the MCU 2 2 3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting Align pin 1 on the IC socket for an FP 80A package on the user system with pin 1 on the user system interface cable head and insert the user system interface cable head into the IC socket on the user system as shown in figure 3 RENESAS 2 2 4 Fastening Cable Head CAUTION Use a Philips type screwdriver whose head matches the screw head The tightening torque must be 0 0784 N m or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the emulator does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary RENESAS Fasten the user system interface cable head to the IC socket for an FP 80A package on the user system with the four screws M2 0 x 12 mm with flat washers provided Each screw should be tightened a little at a time alternating between screws on opposing corners Take special care such as manually securing the IC socket soldered area to prevent the soldered IC socket from being damaged by overtightening the screws
10. mulator by inputting the external clock from the EXTAL terminal on the cable head or connecting a crystal oscillator to the EXTAL and XTAL terminals For details refer to section 13 Clock Pulse Generator in the H8 3001 Series Hardware Manual Figure 9 shows the oscillator circuit on the user system interface cable o To E6000 emulator O O EXTAL XTAL System clock Figure 9 Oscillator Circuit RENESAS 1 3 4 Section 5 Notice Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket The dimensions of the recommended mount pad for the user system IC socket are different from those of the MCU This user system interface cable is specifically designed for the HS3052EPI61H emulator Do not use this cable with any other emulator station To prevent breaking of wires in the cable body do not place heavy or sharp metal objects on the user system interface cable While the emulator station is connected to the user system with the user system interface cable force must not be applied to the cable head Place the emulator station user system interface cable and user system as shown in the example in figure 10 Place components so that the cable body and cable head are parallel to the user system Emulator station Cable E
11. nesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein Renesas Electronics products are classified according to the following three quality grades Standard High Quality and Specific The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application categorized as Specific without the prior written consent of Renesas Electronics Further you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as Specific or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics The quality grade of each Renesas Electronics product is Standard unless otherwise expressly specified in a Renesas Electronics data sheets or data books etc Standard Computers office eq
12. r System Interface Cable Head RENESAS 25 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions after connecting the user system interface cable head to the user system are shown in figure 7 Cable head gt C IC socket User system IC149 080 017 B5 Unit mm manufactured by Tolerance 0 5 mm YAMAICHI ELECTRONICS Co Ltd Figure 7 Resulting Dimensions after Connecting User System Interface Cable 12 RENESAS Section 3 Installing the MCU to the User System CAUTION Check the location of pin 1 before inserting Use a Philips type screwdriver whose head matches the screw head The tightening torque must be 0 0784 N m or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the MCU does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary Check the location of pin before inserting the MCU into the IC socket on the user system as shown in figure 8 After inserting the MCU fasten the socket cover with the provided four screws M2 0 x 8 mm with flat washers Take special care such a
13. s manually securing the IC socket soldered area to prevent the IC socket from being damaged by overtightening the screws or twisting the components RENESAS Screws M2 0 x 8 mm with flat washers Pin 1 mark IC socket ma 1C149 080 017 B5 manufactured b y User system YAMAICHI ELECTRONICS Co Ltd Figure 8 Installing MCU to User System RENESAS Section 4 Verifying Operation 1 When using the H8 3052 series E6000 emulator HS3052EPI61H turn on the emulator according to the procedures described in the H8 300H Series E6000 Emulator User s Manual HS300HEPI61HE 2 Verify the user system interface cable connections by accessing the external memory and ports to check the bus states of the pins If an error is detected recheck the soldered IC socket and the location of pin 1 3 The emulator connected to this user system interface cable supports two kinds of clock sources an emulator internal clock and an external clock on the user system For details refer to the H8 3052 Series E6000 Emulator User s Manual HS3052EPI61HE To use the emulator internal clock Select the clock in the emulator station as the system clock by using the CLOCK command emulator command To use the external clock on the user system as the system clock Select the target clock t or t2 as the system clock b by using the CLOCK command emulator command Supply the external clock from the user system to the e
14. s products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics C 7 D me 7 lt D D ENESAS H8 3001 FP 80A User System Interface Cable HS3001ECH61H for E6000 Emulator User s Manual Renesas Electronics www renesas com Cautions Renesas neither warrants nor grants licenses of any rights of Renesas s or any third party s patent copyright trademark or other intellectual property rights for information contained in this document Renesas bears no responsibility for problems that may arise with third party s rights including intellectual property rights in connection with use of the information contained in this document Products and product specifications may be subject to change without notice Confirm that you have received the latest product standards or specifications before final design purchase or use Renesas makes every attempt to ensure that its products are of high quality and reliability However contact Renesas s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury s
15. uch as aerospace aeronautics nuclear power combustion control transportation traffic safety equipment or medical equipment for life support Design your application so that the product is used within the ranges guaranteed by Renesas particularly for maximum rating operating supply voltage range heat radiation characteristics installation conditions and other characteristics Renesas bears no responsibility for failure or damage when used beyond the guaranteed ranges Even within the guaranteed ranges consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail safes so that the equipment incorporating Renesas product does not cause bodily injury fire or other consequential damage due to operation of the Renesas product This product is not designed to be radiation resistant No one is permitted to reproduce or duplicate in any form the whole or part of this document without written approval from Renesas Contact Renesas s sales office for any questions regarding this document or Renesas semiconductor products Preface Thank you for purchasing this user system interface cable HS3001ECH61H for the Renesas s original microprocessor H8 3001 The HS3001ECH61H is a user system interface cable that connects an H8 3052 series E6000 emulator HS3052EPI61H hereinafter referred to as the emulator to the IC socket for a FP 80A package for the H8 3001 MCU on the
16. uipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems safety equipment and medical equipment not specifically designed for life support Specific Aircraft aerospace equipment submersible repeaters nuclear reactor control systems medical equipment or systems for life support e g artificial life support devices or systems surgical implantations or healthcare intervention e g excision etc and any other applications or purposes that pose a direct threat to human life You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under cert
Download Pdf Manuals
Related Search