IMX
Contents
1. gt To assign a node number to the unit 1 Type def node and press Enter 2 Type the node number 0 if terminal controls a single IMX 2T1 E1 1 255 for multidrop operation and press Enter gt To specify multiplexer call out parameters 1 Type def call and press Enter 2 Set desired parameters for NUMBER OF DIALING RETRIES WAIT FOR CONNECT TIME DIALING MODE PRIMARY and ALTERNATE NUMBERS gt To complete the configuration e Type bye and click Enter The Terminal configuration window closes 2 Basic Configuration Tasks RADview HPOV TDM IMX Preliminary Hardware Configuration 2 IMX 2T1 E1 Management The IMX 2T1 E1 can be managed via Telnet gt To manage the IMX 2T1 E1 via telnet 1 Select the IMX 2T1 E1 icon on the WAN hierarchy map 2 From the Tools menu select Terminal Connect followed by Telnet X term The Telnet X term window appears 3 Release Notes Telnet The IMX 2T1 E1 does not have a graphical application It is managed via Telnet Release Notes 3 IMX Preliminary Hardware Configuration RADview HPOV TDM 4 Release Notes2. RADview HPOV TDM Network Management System for TDM Applications IMX 1994 2002 RAD Data Communications Publication 02 02 Contents Preliminary Hardware Configuration T Haste Config ration Tas sse sire ertet ee Ue tU ign UAR tintin 2 IMX 2T1 E1 Management 3 Release Notes Telnet IMX User s Manual Table of Contents RADview HPOV TDM ii RADview HPOV TDM IMX User s Manual IMX Preliminary Hardware Configuration This chapter describes the preliminary IMX hardware configuration necessary to enable the IMX management icon to be added to the HPOV map 1 Basic Configuration Tasks Preliminary hardware configuration for the IMX is performed using a Terminal Emulation program When selecting parameters click the F and B keys to move forward and backwards among the possible values for the selected parameter Click Enter to make a selection and the spacebar to move on to the next parameter gt To configure IMX 2T1 E1 from the supervisory terminal 1 Enter the following Communication Parameters and then click OK Baud Rate 9 6 Kbps Data Bits 8 Stop Bits 1 Parity None 2 If AUTO Autobaud mode is enabled press lt CR gt three times IMX 2T1 E1 identifies the operating rate of the terminal and uses this rate for the current session 3 Ifthe terminal prompts for a password enter the password and press CR Note The default password is IMX If the IMX 2T1 E1 node number is not zero enter the node
3. number and password using the following syntax NODE Space node number Space password CR 4 Enter the terminal definition by typing DEF TERM terminal type CR Valid terminal types are TV920 VT52 and VT100 Note Ifyou enter DEF TERM without terminal type IMX 2T1 E1 resets all control terminal codes to zero gt To define serial port parameters 1 Type def sp and press Enter Basic Configuration Tasks 1 IMX Preliminary Hardware Configuration RADview HPOV TDM The default parameters will be displayed 2 Set SPEED to 9 6 Kbps 3 Set AUXILIARY DEVICE to NMS Slip 4 If you have a dial out modem connected to the IMX 2T1 E1 set CALL OUT MODE to Enable gt To define system parameters 1 Type def sys then press Enter The default parameters will be displayed 2 Setthe DNLOAD Mode to TS1 to enable in band and out band communication gt To define agent parameters to configure SNMP parameters 1 Type def agent and click Enter 2 Setdesired parameters and press Enter gt To assign a different logical name to the IMX 2T1 E1 e Type db name and enter a logical name of up to eight alphanumeric characters gt To reset the IMX 2T1 E1 e Type reset to reinitialize the IMX 2T1 E1 gt To define a data channel or Fractional T1 parameters 1 Type Ch2 and press Enter 2 Enter desired parameters and press Enter gt To set link parameters e Type def link X where X link number and press Enter
Download Pdf Manuals
Related Search
IMX imx.to imx girls imx models imx untitled imx peach imx pilates imx star imx8 imx95 imx stella imx trixie imx.to ss olivia imx sandra imx gallery imx678 imx 2025 imx sarah imx telegraph imx medical imx to vlyaskovets imx290 imx291 cmos sensor imx766 imx gina imx wallet