7286 DOOR PROP.qxd - Dortronics Systems, Inc.
Contents
1. In addition to the dedicated local sounder driver a SPDT output is furnished to operate other remote alarm devices Also a form C dry contact is supplied that can be used for signaling an independent monitoring system when an authorized door unlock condition occurs Request to Exit A single R E X input controls the door lock and alarm outputs The alarm func tions are automatically shunted during an authorized unlock sequence This allows the door prop alarm to be inhibited during an extended authorized door opening Alarm Shunt In this mode upon contact closure the unit will not go into either warning or alarm The REX input still functions as usual Manual or Automatic Alarm Reset Typically the door prop alarm is silenced and reset upon door closing If no one is available to acknowledge alarms a timed automatic reset may be engaged to silence the alarm after a preset period of from 0 seconds to 5 minutes if the door remains in the open position In the manual reset mode the audio alarm will sound continu ously even after the door is closed This manual reset mode requires reset by input from a normally open momentary contact such as a Key switch or Digital Keypad to silence the alarm AE N O RESET 4 OSED SECURE CYCLE uz we 7 2 ef 4 7i CLOSED ACTIVE nie 1668 SAG HARBOR TURNPIKE www dortronics com 800 906 0137 SHU2. by means of an onboard potentiometer e Alarm mode At the end of the warning mode if the door has not been closed the unit enters the full alarm mode The intermittent audible beep of the warning phase changes to a steady alarm and the alarm relay output is closed to signal an alarm condition to any external security system The alarm can be reset either manually or automatically at the user s discretion Unless the recycle mode is active see below the alarm is a latching mode The mode cannot be exited until the door is re secured and the alarm reset e REX Recycle mode This mode allows the 7200 to exit the alarm mode and go back to the rex mode on a REX input closure e Shunt mode When a closure is provided to the shunt input the 7200 enters the shunt mode During this mode the unit will not go into either warning or alarm The REX input still functions as usual to provide either security or access but no alarm protection 1s provided in this mode Features Power Input 12 or 24 VDC as required by lock Current draw is 100 ma maximum alarm sounder activated without lock requirement Lock Output Solid state powered output for fail safe or fail secure selectable by jumper Audio Output Solid state to local piezo sounder selectable volume by jumper REX Input Dry contact NO from access control lock relay or push button switch Rex Recycle Input When closed allows a subsequent REX request to be serviced during an alar
3. FAIL SAFE SECURE This set of pins is used to configure the lock output for either a fail safe device such as a magnetic lock or a fail secure device such as a magnetic strike Install a jumper across these pins for fail secure strike output Remove the jumper for fail safe magnetic lock operation ARM SHUNT ALARM DOOR SWITCH The 7600 interface connector is used to interface the 7200 to the Dortronics 7600 Annunciator unit All connections are isolated dry contact Polarity does not matter ARM Connects to the ARM input of the 7600 ALARM Connects directly to the ALARM input of the 7600 DOOR Connects directly to the DOOR input of the 7600 A separate 7200PT unit must be used for each individual zone of the 7600 on which door prop protection is needed SETUP SETTING THE PROP TIME The prop time is user adjustable in the range of 0 seconds to 90 minutes A 16 position rotary switch is used to make the adjustment The switch is labeled 0 9 and A F Refer to the chart below for switch settings to achieve various timer settings 0 1 2 3 4 5 6 T 8 9 A B C D E INTERFACE TO EXISTING SECURITY SYSTEM MAGNETIC LOCK OR STRIKE E 5999999 N NO N NO DPS Al MIRROR ALARM RELAY 2 RELAY 1 12 or 24 VDC 24 Z ate RESET TIME 7600 INTRFACE DPS REX SH
4. i j PUSH TO 4 5 I i Pi SS z y 7286 5 7286 5 24 7286 PT5 MP23 Model Descriptions Additional Features 7286 5 Inputs amp Outputs 7286 5 Dry Contact and Powered Outputs Local Door Prop Alarm Module on single gang 2 3 4 x 4 1 2 stainless steel wall plate with tri color LED and 95 dB piezo audible sounder 7286 PT5 24 Local Door Prop Alarm Module on dou ble gang 4 1 2 x 4 1 2 stainless steel plate with tri color LED for visual status 95 dB piezo audible sounder Includes key switch assembly with dual DPDT switches 1 Momentary for RESET and or REX plus 1 Maintained for SHUNT One set of contacts from each DPDT switch may be used to also signal an access control system 7286 5 24 Same as 7286 PT5 24 above supplied with 1 1 4 mortise cylinder 7286 PT5 MP23 Local Door Prop Alarm Module on dou ble gang 4 1 2 x 4 1 2 stainless steel plate with tri color LED for visual status 95 dB piezo audible sounder Includes a 1 9 16 dia momentary push button with 1 set of Normally Open contacts 1 set Normally Closed contacts Typically the N C contact output is used to break power to maglock while the N O contact is used to signal the REX to an access control system The lock relay of the card access system is used as the REX input to the 7286 PTS
5. Economical Single Door Monitoring Adjustable Exit Time amp Warning Period Visual amp Audio Alarm Indication Made in the USA PDS7286 05 05 Reliable Operation 7286 SERIES DOOR PROP ALARMS Local and Remote Alarms The Dortronics 7286 PT series of door prop alarms provide an audible warning sounder at the door if it is not closed within a specified time Upon a forced door condition or if the door has not been closed during the warning period an alarm relay is activated and can be utilized to signal other monitoring systems A Piezo alert is also sounded locally Universal Operation Opening the door or an authorized REX will activate the PT timer If the opening is forced an immediate alarm is sounded and signalled to monitoring systems The allowed door open timer starts upon an authorized door opening If the door has not closed at the end of this period a local warning period begins If the door remains unsecured past this time period then an alarm condition is triggered When supplied with the optional push button a sec ond set of momentary switch contacts are available to provide a R E X signal to an access control system Adjustable Exit Time Period The allowed door open time may be set from seconds to 90 minutes This timer begins when the door has opened and the door unlock signal from the access system ceases A warning will sound if the door has not been closed at the end of the time perio
6. NT CLOSED ACTIVE WOO TIMANS VA 7286 5 Specifications Door Prop Alarms shall be manufactured by Dortronics Systems Inc Onboard Key switch controls shall be momentary amp alternate action with DPDT 3 amps 125VAC minimum as scheduled Optional 1 1 4 Mortise Cylinder as required Push button switch controls shall be momen tary with 1 set each N O N C 10 amps 125VAC minimum as scheduled Push Button Switch caps shall be at least 1 9 16 in diameter 7286 PTS assemblies shall be flush wall mounted to standard recessed electrical boxes Mounting screws shall be slotted oval head stainless steel Pin in Hex Head tamper resistant screws shall be supplied where required Mounting plates shall be constructed of stainless steel in single gang or double gang as noted and may be supplied with paint filled engraving SAG HARBOR NY 11963 631 725 8148 FAX FALSAS ALRINDAS ONLISTXS OL SOVIVAINI 000 DORTRONICS SYSTEMS INC 1668 Sag Harbor Tpke Sag Harbor N Y 11963 Tel 631 725 0505 800 906 0137 Fax 631 725 8148 7286 SERIES USER MANUAL C FUNCTIONALITY The 7200 door prop timer is a multi function control device designed to set limits on how long a door is allowed to remain open The various functions are as follows e Secure mode The door is secured and locked In this mode the door status is continuously checked An alarm condition results if any attempt is made to force the door open Sec
7. UNT MBS RECYCLE ACTIVE SHUNT ACTIV PRECYCLE CLOSED N O RESET CLOSED ALTERNATE WIRING SEE TEXT SETTING THE WARNING TIME The warning time is adjustable over the range of 0 seconds to 5 minutes Referring to the illustration above use the potentiometer labeled Warning Time to adjust the time period This is a multi turn adjustment and is adjustable over a wide time range The adjustment may be a little tricky if very short warning times are needed A trial and error procedure will be necessary to get exact times SETTING THE AUTO RESET TIME The Auto Reset time is also adjustable over the range of seconds to 5 minutes Referring to the illustration above use the potentiometer labeled Auto Reset Time to adjust the time period This is a multi turn adjustment and is adjustable over a wide time range The adjustment may be a little tricky if very short Auto Reset times are needed A trial and error procedure will be necessary to get exact times OPERATION Prior to applying power the door should be closed Upon power up the system should go into a secure state indicated by a steady green LED REX The REX Request for Exit release mode allows only authorized persons to exit and requires the use of a key keypad card reader or other device to restrict access to authorized personnel The door will immediately unlock and the LED will change color from green to yellow If the door remains open after t
8. WALSAS IOYULNOD 55999 IWNOIS Ol GASN Ad AYN SLOVLNOO NIYLNIYIN JO 195 GNOOAS SHL LAdNI wALNOHS YOSs HOLIMSAAM AHL SLOVLINOO LAS NIVLNIVA SHL NIZNILN O N ANId ON MOVISA Woo Ss WOO AvD _ 58 JFONVAO 5 MID HOLIMS CANIVLNIVIA 1 INdNi LNNHSs JSN INOJ AAV LNSAWOW C 4INIVLINIVW Lassa er Kay LNOHS gt _Al oe A a NOILViua AAD 7286 5 23 PUSH BUTTON SWITCH INSTRUCTIONS SHOWN WITH OPTIONAL TEXT 44 SHOWN WITH MP23 PUSH BUTTON O 9211 MP23 PUSH BUTTON CONTACT BLOCK 3 1 IN 101 VN rN 2 CLEARANCE FRONT VIEW SIDE VIEW BACK VIEW SPECS USE FUR REX UTILIZING THE N O MOMENTARY SET OF SWITCH RATING 5211 MP23PP MOMENTARY SWITCH 10 115VAC OR 24VDC CONTACTS FROM THE PUSH BUTTON ne ce 1 SET NO 1 SET NC FOR THE REX INPUT THE SECOND SET OF N C MOMENTARY CONTACTS MAY BE USED TO E EEEE TEE oe otek SIGNAL THE ACCESS SYSTEM OF AN LED RATING 08 24VDC AUTHORIZED REQUEST PIEZO RATING 08 24VAC DORTRONICS SYSTEMS INC 7286 PTS MP23 SWITCH INSTRUCTIONS RE FACE PLATE 032 THICK STAINLESS
9. a manual reset REX RECYCLE This input determines how the 7200 handles a REX request during an alarm condition e If the REX RECYCLE is open a REX request will be ignored during an alarm e If the REX RECYCLE is closed a REX request will take the 7200 out of alarm in effect resetting the alarm condition and a normal REX cycle will begin SHUNT The SHUNT input is used to prevent the 7200 from going into alarm or if already in an alarm state to temporarily override the alarm The shunt does not reset an alarm that is already in progress the 7200 will go back to the alarm state when the shunt input opens REV C 04 25 05 10 J azs 1 1338 JLF NAVAT ad3SN LON SLOVLINOO 195 eooo eae GNOOAS LAAN 13593 IHL HOLIMS ADI 982d SLOVINOO AYWLNAWOW ONIZITILA 41 SWALSAS LSANOAY GAZIMOHLNV SOINOULYOG NV WALSAS SS3OOV IHL TWNOIS Ol G4SN Ad AYN SLOVINOO AYVLNANWOW JO LAS GQNOOSAS SHL LAdNI X34 AHL HOLIMSAAM AHL SLOVLINOO JO 195 AYVINSANOW SHL NIZNILAN a ASO ON ANTE LIHA WOO NADE WOO A0vIa ON In JN Gcd G d NOT IV Loa ASS MD HOLIMS AYVLINANOW 1 19599 10 ASN MJIA WOVE SETS AONVYVS19 11 Q Gld 98 2 AJANI IAD IWNOILdo NOILYLON WYO AOLVNLOV HALIM NMOS SNOILONALSNI HOLIMS 982 NOILIGNOO uLNOHS 4O
10. d Adjustable Warning Time Period The warning period may be set from 0 sec onds to 5 minutes During this sequence the sounder emits a beeping tone to remind the user to close the door If the door is not closed before the end of this warning period then the door prop alarm sequence is activated At this point the alarm relay is activated and the local sounder emits a steady alarm alert This alarm is continuous until reset one of 3 ways 1 upon door closure 2 by Auto timed Reset 3 Manual reset by Key switch Digital keypad or other N O device The use of a Door Position Switch is required Compact Mounting Styles The Dortronics PT door prop modules are available in any of the 7286 series single or double gang wall plate designs The single plate will accommodate the PT module with sounder and LED When used with mushroom pushbuttons or key switches a double gang plate is required LED Indicator A tri state LED is provided for a visual indica tion of the door prop alarm condition The LED is green when the door is secured amber during door unlock shunt flashing amber when door is open authorized flashing red during the warning period and steady red while in alarm DORTRONIGCS C7 SYSTEMS INC 7286 SERIES DOOR PROP ALARMS 7286 PT5 CONFIGURATIONS 23 H 4 44 SHOWN WITH XK i 7 OPTIONAL CYLINDER f
11. he REX is released the Prop Timer begins running The length of the prop cycle may be anywhere from 0 seconds to 5 minutes depending on the setting of the 16 position rotary switch If the door is not closed before the Prop Timer cycle is complete the 7200 will go into the Warning cycle followed by the Alarm mode Note that the timing cycle starts only after the input is released This feature can be useful if you have need for the door to remain unlocked for extended time periods A toggle switch may be connected to the REX input on terminal strip TS1 Setting the switch to the closed position will hold the door in the unlocked position indefinitely WARNING If after an initial REX request the door is held open long enough for the Prop Time to expire the 7200 will go into its warning mode During this time there will be a local warning consisting of an intermittent beep accompanied by a flashing red LED This is an indication that the door has been opened longer than the maximum allowable time and that an alarm in imminent The warning will reset automatically if the door is closed before the 7200 goes into alarm if another Rex request 15 received before the unit goes into alarm The length of the warning cycle may be anywhere in the range of 0 seconds to 5 minutes depending on the setting of potentiometer R5 ALARM If the door remains open after the warning period expires the 7200 will go into full alarm The audible beep and
12. m When open ignores REX during alarm Door Switch Bond Sensor Input Dry Contact input Optional supervised input configuration available Automatic Alarm Shunt REX input can be held closed indefinitely to prevent alarm Manual Bypass Shunt Input Dry contact input from remote device key switch shunts alarm Door Switch Output Relay output mirrors door switch input for access control system Alarm Output Relay output triggered on forced door or door held open after warning Arm Shunt Output Relay output triggered on remote shunt or during authorized access Manual or Automatic Timed Sec 5 Min alarm reset user selectable and adjustable User Adjustable Warning Time 0 Sec 5 Min User Adjustable Door Prop time 0 Sec 90 Min FIELD WIRING INTERFACE TO EXISTING SECURITY SYSTEM MAGNETIC LOCK OR STRIKE SISSTISSSS ARM ALARM RELAY 2 RELAY 1 SE ZI lt S 5 X Ta WARNING TIME TIME 2 5 DPS REX SHUNT MBS RECYCLE SECURE ACTIVE SHUNT ACTIVE CLOSED RECYCLE N O RESET CLOSED LOSED af ALTERNATE WIRING SEE TEXT INSTALLATION INPUTS TS1 RESET This input silences and resets an alarm condition There are two ways to use this input 1 If manual reset is desired a normally open device is used 1 e pushbutton key switch keypad etc In this mode of operation the door must be closed prior to applying the reset A momentary cl
13. osure of the reset input will reset the alarm If automatic reset is desired a jumper should be installed across the reset input In this mode the reset will be automatic and will occur when the auto reset timer times out See Setting the Auto Reset Timer DPS MBS This input monitors either the Door Position Switch or the Magnetic Bond Sensor Switch contacts should be closed when the door 1s secure REX RECYCLE This input determines the function of the REX input during an alarm condition e If the RECYCLE input is open the REX input is ignored during an alarm condition The REX remains disabled until the alarm 15 reset e If the RECYCLE is closed the REX remains enabled during an alarm condition A REX input will take the unit out of alarm and through a new REX cycle Either a toggle type switch or a permanent jumper may be used to enable the REX Recycle If this function is not used the input may be left permanently open SHUNT Upon closure this input prevents the 7200 from going into alarm The shunt also overrides but does not reset an existing alarm If an existing alarm condition exists when the shunt input is activated the alarm will be disabled but the 7200 will return to the alarm state as soon as the shunt is removed REX The Request for Exit input can be tied to a key switch digital keypad card reader or any other normally open device that will provide access to authorized personnel only OUTPUTS TS2 DPS MIRROR Thi
14. red LED are now continuous and the alarm relay closes to signal any external system that the alarm condition exists The alarm cycle can be exited in one of three ways 1 By a RESET The reset may be either manual or automatic See RESET below 2 an active SHUNT input See SHUNT below 3 Ifthe REX RECYCLE input is closed by an active REX input See REX RECYCLE below RESET The RESET input is used to silence and reset an alarm condition on the 7200 The reset can be configured as either a manual or automatic timed reset MANUAL RESET If a normally opened device is connected to the RESET input the manual reset will be enabled To manually reset an alarm 1 Close the door The 7200 cannot be manually reset unless the door is closed and secured 2 Momentarily close the reset input AUTO RESET If a normally closed device or a permanent jumper is connected to the RESET input the automatic reset will be enabled An auto reset functions as follows e The 7200 will automatically reset an alarm condition after the auto reset timer times out see Setting the Auto Reset Time in the SETUP section e The alarm will be reset regardless of whether the door is open or closed e An alarm can always be reset manually at any time before the auto reset has occurred Opening and re closing the reset input will override the auto reset and cause a manual reset of the alarm Keep in mind that the door must be closed prior to performing
15. s is an isolated dry contact output that follows or mirrors the state of the Door Position Switch ARM RELAY 2 Dry contact output that reports an authorized or shunt condition to an external system ALARM RELAY 1 Dry contact output that reports an alarm condition to an external system LOCK Powered output drives a locking device Can be user configured via jumper JP10 for either fail safe or fail secure devices POWER POWER Connect either a 12V or 24V depending on lock requirements regulated DC power supply to the power terminals The current capacity of the power supply should be chosen based on the lock requirements Note the polarity shown in the field wiring diagram Incorrect polarity will not damage the 7200 but the unit will not function HEADER 1 JP 10 FAIL SAFE SECURE JP 7 FORCED DOOR BY PASS JP 4 HI LOW VOLUME 5 REMOTE AUDIO OUTPUT 5 AUDIO OUT These pins are used to connect a self driven piezo type audio sounder The sounder should be rated at 9 to 12 volts DC JP4 AUDIO VOLUME The volume of the audio sounder can be adjusted for low or high volume Install a jumper on JP4 for high volume Remove the jumper for low volume 7 FORCED DOOR BY PASS With jumper in place a REX input is not required Opening the door will start the held open timing sequence allowable open time delay warning time delay auto reset timer without creating a forced door alarm JP10
16. urity status can be determined by either a door position switch DPS or a magnetic bond sensor MBS at the users discretion e REX request for exit access mode This mode begins when a closure is provided to the REX input and continues until the REX input opens During this mode the door is unsecured There 15 no time limit on the REX mode As long as the rex input remains active the door remains unlocked and may be either opened or closed e Prop mode When the rex input is removed and the door is left open an internal timer sequence begins The length of the Prop mode is user selected in the range of 0 seconds to 90 minutes by means of a 16 position rotary switch If the REX input again becomes active before the Prop mode times out the 7200 returns to the REX mode of operation If the door is closed before the Prop mode times out the unit goes back to the secure mode of operation e Warning mode If the door is held open long enough to allow the preset prop mode interval to time out the 7200 enters the warning mode During this mode a local at the door audible warning is sounded The on board sounder beeps at a rate of 1 beep per second accompanied by a flashing red LED The warning is not at this point a full alarm but only an audible and visual warning that an alarm is imminent and that the door should be closed to avoid going into the alarm mode The length of the warning is user settable in the range of seconds to 5 minutes
Download Pdf Manuals
Related Search