Home
"user manual"
Contents
1. If using an external trigger the default setting is a falling edge or switch closure If a rising edge or open switch is desired check the Trigger box on the Camera Setup window The default setting for the data transfer speed from the camera to the computer is approximately 250 to 300 Mbit s To increase the data transfer speed to the full 400 Mbit s check the High Transfer Speed box on the Camera Setup window Click on the Options button to access additional power battery and trigger options Click on the Preview Normal button or click on the Preview Correct Exposure button Adjust the exposure while in Preview mode by using the Exposure slider at the top of the toolbar Click on the green Set Ready for Record button The Ready Data LED on the camera will light up green Click on the red Trigger button or press the manual control trigger button The red Ready Data LED will blink red while recording images It will light up solid red when the buffer is full Click on the green Set Ready for Record button The Ready Data LED on the camera will light up green Click on the white Set for Pre trigger Mode button The Ready Data LED will blink red and green Click on the red Trigger button The red Ready Data LED will blink red while recording images It will light up solid red when the buffer is full Note The camera will not display a live image while it is in record mode les redlake com Imaging Studio Ve
2. 50 50 100 0 T tL t z Hl Contrast correction 100 T 100 0 _ E a 100 0 ee Soften Sharpen Find Edges Edge Enhance Movie Image Analysis 4 The right hand window provides camera and movie lists as well gt AEDLAKE as access to advanced function tabs sales redlake com
3. Ver 1 2 This quick start guide provides instructions for setting up a basic system with Imaging Studio For additional information download the user s manual from the Redlake FTP site at ftp ftp redlake com motion PC running Windows 2000 or XP with Service Pack 1 or higher PCMCIA card with power supply see user s manual for additional power options and information One of the following camera s MotionXtra HG SE MotionScope M3 or registered MotionScope M1 M2 CD with application software 6 pin Firewire 1394 Interface cable Pentium Ill 1 8 GHz with MMX DRAM 512 MB or higher Graphic memory 64 MB or higher Display 1280 x 768 pixel resolution or higher HDD capacity 40 GB or higher CD or DVD ROM 6 pin IEEE 1394a interface PCMCIA with power supply or PCI type with Texas Instruments chip set Note Administrator Privileges on the PC are required before installing the software Install the software before connecting the camera to the PC If you are installing software to control multiple cameras and or previously installed cameras please refer to the user s manual 1 2 Insert the CD into CD ROM drive of the computer Select the CD drive and double click on the Redlake Imaging Studio Installer msi file The program will start automatically and guide you through the installation If required register the camera by double clicking on the Redlake Imaging Studio Register Key exe on the CD and install it
4. r 1 2 Quick Start Guide View Recorded Images 1 Click on the Playback button 2 Click on the Stop button and the Play Forward button to replay the sequence Quick Reference Camera Set up and Operation Open camera and Save settings to the change settings camera Preview normal with ue Enable camera record Arm for pre trigger mode Trigger Sleep mode View and Playback Go to last frame M Go to first frame Step forward one frame IP d Step back one frame Play forward Playback Go to beginning of the Go to the end of the sequence sequence Adjust camera color and Cut and Modify a Sequence Select Istframeof hi Select last frame of sequence sequence Store a Sequence Save stored frames in Auto download in RAW RAW format format Download as a movie a4 5 Download as a single Mien iG file image For additional information download the user s manual from the Redlake FTP site at ftp ftp redlake com motion www redlake com Acquisition Page 2 5 a F 10000 Out Shutter time slider Playback speed slider H Mitra AG 5E 1 35 10 546 Live 1 lB 1260 1024 Pixel 500 Framesjsec l 2000 us Shutter l 1 024 s Pre Trigger Si AVI File L Do cuments and Settings jana fn Ci 180512 Fixel l 125 Frames sec 8000 us Shutter lS 4 096 us Pre Trigger E Gamma correction T 4 r rT T T T T E Brightness correction 100
5. to the PC Make sure the software is installed on the PC before connecting the camera to the computer 1 2 Switch the camera power to the ON position When the Power and Ready Data LEDs light up connect the Firewire cable to the Firewire port on the camera Connect the other end of the Firewire cable to the PC The Windows Found New Hardware Wizard will display after the camera is connected to the PC Select the option to Install the software automatically and click on the Next button From the Windows Hardware Installation screen select the Continue Anyway button and follow the on screen instructions to complete the installation ww rediake com Quick Start Guide Page 1 From the main toolbar select the Camera Setup icon or double click on the camera name in the right hand toolbar window Select the Vertical Resolution using the Lines drop down menu and the Horizontal Resolution using the Pixel Line drop down menu Select the Speed using the Frames sec drop down menu Select the Exposure using the Shutter Time text box Select the Pre trigger time by typing the desired percentage into the Pre Trig of Buffer text box from the Camera Setup window The Pre Trig Time s text box displays the resulting pre trigger time The default setting for the Sequence Length is the total available recording time in seconds To change the sequence length type the desired number of seconds into the Sequence Length s text box
Download Pdf Manuals
Related Search
Related Contents
Canon VB-H41 共通取扱説明書 [PDF形式] Migrationsleitfaden 4.0 Operating Instructions MANUAL DE INSTALACION Y USO 原動機付自転車改造証明書 Samsung 511M ユーザーマニュアル Model 250 User Manual - Chemglass Life Sciences Copyright © All rights reserved.
Failed to retrieve file