Model 306X Input Option Card Installation Instructions
Contents
1. Stand the unit on its face Use the hex key to remove the 4 screws 2 on each side of the top cover Loosen the 2 rear bottom screws Figure 1 Full rack only use a small Phillips screwdriver to remove the 2 top cover screws and 1 rear bottom screw Figure 1 Remove the rear plastic bezel The cover is tracked Slide the top cover to the rear on the track to remove it Remove the rear panel option plate screws and set them aside Figure 2 Remove the rear panel option plate With the instrument still standing on its face turn it to view the circuit board inside From inside the instrument place the option card into its position in the rear panel Orient the card so that the 14 pin ribbon cable connector is toward the bottom of the instrument closest to the main circuit board Figure 3 Lake Shore Cryotronics Inc 575 McCorkle Blvd Westerville Ohio 43082 Tel 614 891 2244 Fax 614 818 1600 e mail service lakeshore com www lakeshore com FO10 09 00 Revision E 1 May 2014 Attach connector SO arrow is on top Figure 3 Proper orientation of the ribbon cable 10 11 connector plug Half rack only use the screws removed in step 1 to attach the card by starting both screws in a few threads before tightening either Full rack only use the screws removed in step 6 to attach the card by starting both screws in a few threads before tightening either Fully tighten both screws 12 13 142. 15 16 17 18 19 Lake Shore CRYOTRONICS You do not need to do this step if you are installing the Model 3062 Insert the 14 pin ribbon cable connector plug into the socket on the option board Orient the ribbon cable connector plug so that the arrow nub slides into the plug slot and the ribbon cable exits downward Figure 3 Plug the other end of the cable into the main board option connector J12 Slide the top cover forward in the track provided on each side of the unit Replace the rear plastic bezel by sliding it straight into the unit Full rack only use a small Phillips head screwdriver to replace the 2 top cover screws and the 1 bottom cover screw Use the hex key to replace the 4 screws on the sides of the top covers Tighten the 2 rear bottom screws Replace the power cord in the rear of the unit and set the power switch to On To verify option card installation check the instrument information by pressing and holding the Escape key Refer to instrument user s manual for more information on verifying option card installation Lake Shore Cryotronics Inc 575 McCorkle Blvd Westerville Ohio 43082 Tel 614 891 2244 Fax 614 818 1600 e mail service lakeshore com www lakeshore com FO10 09 00 Revision E 1 May 2014
3. Instructions Input Option Card Installation Model 306X FIELD INSTALLATION Input option card kit 1 14 conductor ribbon cable 1 Option card Lake Shore Required tools e Small Phillips head screwdriver e 5 64 inch hex key included CAUTION The components on this board are electrostatic discharge sensitive ESDS devices Wear shock proof wrist straps resistor limited to lt 5 mA to prevent injury to service personnel and to avoid inducing an electrostatic discharge ESD into the device CRYO TRONICS CAUTION x GJ Sensitive Device NOTE The Model 3060 can be installed in a half Remove Remove rear rear bottom plastic cover screw bezel unshown full rack only Loosen bottom _ rear Remove top side cover cover screws screws ull rack onl both sides To remove Remove top top cover side cover slide it to screws both sides pie par tracks Figure 1 Cover screws Rear panel option plate screws full rack Shore wte pen Madel 3060 Thermocouple e 22 v 9 eu Option Figure 2 Option plate screws rack or full rack instrument All other option cards can only be installed in full rack instruments 1 Half rack only Remove the two screws used to attach the ceramic block to the full rack adapter plate set aside the screws and discard full rack adapter plate Turn instrument power switch OFF Unplug the power cord from the wall outlet then from the instrument
Download Pdf Manuals
Related Search