Hardware manual
Contents
1. P1 Analogue input selection Selects which rear panel analogue input connector is in use No Selection Green XLR Blue RCA P2 Microphone selection Selects microphone input mode for calibration phase of installation No Selection IO configuration notes If using digital mode exclusively analogue input set to No Selection and there is no valid input source the unit mutes If digital and analogue modes are selected simultaneously the unit uses the digital input if a valid digital source is detected and if not defaults to analogue input When the microphone input is selected the unit is automatically placed in analogue mode The unit defaults to the analogue condition when going from microphone to no input DEQX HDP 4 Users Manual 17 Digital and analogue input selections are saved when you switch back from IO Configuration Mode to Standard Operating Mode Microphone selections are not saved The optional digital outputs carry the same signals as the analogue outputs Front panel button light special modes The front panel button lights also indicate special modes and fault conditions as follows Button Lights Selection All lights flashing blue Unit was booted in safe mode a special mode used in case a firmware upgrade has failed Filtering will not work but firmware can be updated again Red Red Red Yellow Red Red Yellow Fault mode Unit has faulted and needs to Red2. DEQX HDP 4 Users Manual 11 Volume The Volume button adjusts the output volume of the unit in the same manner as the volume button on the unit s front panel In other words each button press increments or decrements in 1dB steps from OdB to above 24dB then in 2dB steps above 36dB then in 3dB steps above 48dB then in 6dB steps down to 120dB The button increases the volume the v button decreases the volume EQ 3 Band EQ Low Mid and High In its simplest form the EQ on the remote control can be used as a 3 band graphic equalizer Unless adjusted to other frequencies see Advanced EQ below the frequencies of the 3 bands are Bass Low 110Hz Mid 440Hz Treble High 3500Hz To adjust the boost of the bass low band press the Low button then press the Gain button to boost the bass or the Gain button to cut the bass Similarly to adjust the boost of the mid band press the Mid button then press the Gain button to boost it or the Gain button to cut it And to adjust the boost of the treble high band press the High button then press the Gain button to boost it or the Gain button to cut it Each press of the Gain or Gain buttons changes the boost of the relevant band by 1 dB Holding down either of these buttons for more than 1 second will cause the boost to be changed continuously until the button is released Whichever band you have selected will stay active until you select another
3. Replace the cover by sliding it back into place If the remote control does not work check that the batteries have been installed correctly The charge of the batteries will run down over time and with use Replace the batteries when this occurs DEQX HDP 4 Users Manual 15 Factory Settings The unit is shipped with the following factory settings Profile 0 Bypass Bypass Bypass Bypass Profile 1 Bypass Bypass Bypass Profile 2 100Hz 24dB Octave 100Hz 24dB Octave 2000 Hz 102 Linkwitz Riley low Linkwitz Riley low dB Octave Linear pass filter pass filter Phase low pass 2000 Hz 102 filter dB Octave Linear Phase high pass filter Front panel IO configuration mode The front panel can operate in normal mode described above and IO configuration mode To enter or exit IO Configuration mode hold down the P3 button on the far right and press the 1 0 Standby button on the far left In IO Configuration mode you can select rear panel digital inputs rear panel analogue inputs microphone mode and digital sync source Button lights indicate the selection made Hold P3 and press VO Stand by button to enter exit VO configuration mode WIP peste reas cabibew ice ponceise digital analogue microphone input input settings 16 DEQX HDP 4 Users Manual Volume button Digital input selection Selects which rear panel digital input connector is in use No Selection Digital 4 Digital S
4. cable bi amplified A tri wired speaker has three separate cables for amplifier connection The cables can be connected in parallel to a single amplifier single amplified or a separate amplifier for each cable tri amplified The diagrams below show a three driver speaker Two driver speakers can also be single wired bi wired and bi amplified Single wired In a single wired configuration a single cable connects the amplifier to the speaker An internal crossover within the speaker filters the signal to distribute the appropriate frequencies to each driver This corresponds to the DEQX Single Amp configuration Bi wired In a bi wired configuration the speaker is connected to a single amplifier by two cables This corresponds to the DEQX Single Amp configuration DEQX HDP 4 Users Manual 23 Tri wired In a tri wired configuration the speaker is connected to a single amplifier by three cables This corresponds to the DEQX Single Amp configuration Bi amplified In a bi amplified configuration two separate amplified channels are connected to the speaker by two separate cables This corresponds to the DEQX Bi Amp configuration Note that it is preferable that the speaker s internal crossover be disconnected in this configuration Signa Source Tri amplified In a tri amplified configuration three separate amplified channels are connected to the speaker by three separate cables This corresponds to the DEQX
5. a preamplifier and process it prior to the main amplification stage Digital signal processing in the DEQX unit corrects for the specific characteristics of the speakers and room The result is reduced distortion coherent phase a wider sound stage and improved imaging and accuracy Compact Dise Power Amplifier This diagram shows a typical home configuration using the HDP 4 The CD player signal is preamplified processed by the PDC amplified and distributed to the speakers The HDP 4 can provide dramatic performance improvements to a wide range of home stereo home theatre and professional audio configurations 8 DEQX HDP 4 Users Manual DEQX unit features and operation The DEQX unit provides a simple and elegant front panel for controlling input and output volume and selection of stored profiles Each profile stores one set of speaker correction equalization and crossover curves Setting up profiles and other configuration of the DEQX unit requires connecting a PC and running the configuration software Your professional installer may have performed this setup The rear panel offers connectors for input output PC connection and power Front panel standard operating mode In standard operating mode the front panel buttons control standby mode volume and profile selection Standby Button Volume Buttons Profile Selection Buttons Press ary two button 9o select profile Standby button Disabl
6. measure the loudspeaker and room response so that an appropriate correction filter can be created Phantom power on by default may be selected for condenser measurement microphones Balanced Audio In XLR 2 balanced analogue audio input channels Unbalanced Audio In RCA 2 unbalanced analogue audio input channels Unbalanced Audio Out RCA 6 unbalanced analogue audio output channels Balanced Audio Out XLR HDP 4 only 6 balanced analogue audio output channels Both balanced and unbalanced outputs are available at all times No settings need to be changed to select between the two Digital outputs 3 digital outputs are provided for connection to external DACs Note that maxiumim sample rate of 96kHz is available Digital Output DSP input pass this output allows the signal input of the DSP to be passed out with no processing to enalble multi way DEQX system in conjunsion with the RS232 system control interface Power switch The power switch removes power from the unit Use the standby button located on the front panel for most purposes Use the rear power switch when disconnecting cables IEC mains socket This accepts a standard 110 240V 50 60 Hz IEC mains plug DEQX HDP 4 Users Manual 19 Installation End users should refer to their installer s Installer Information on page 31 for details specific to their installation Read below for more background information on how the DEQX system works The hardware installation st
7. the manufacturer When using rack mounting brackets use only the brackets supplied or specified by the manufacturer Unplug this product during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the product has been damaged in any way such as when the power cord or plug are damaged liquid has been spilled or objects have fallen into the product the product has been exposed to rain or moisture does not operate normally or has been dropped 4 DEQX HDP 4 Users Manual Cleaning and Maintenance Always unplug the product from the electrical outlet before cleaning Do not use abrasive cleaners Simply wipe the exterior with a clean soft cloth A small amount of non abrasive cleaner may be used on the cloth to remove any excessive dirt or fingerprints Document Version Release date 1 June 2012 This document relates to version 3 0 of the DEQX Calibration Software and version 201 05 of the firmware The colors of button lights when the PDC is used with earlier versions of the firmware may differ from those described herein For the latest software firmware and documentation check www deqx com Table of Contents Unpacking the unit 6 Accessories 6 About this manual 6 Introduction 7 DEQX unit features and operation 8 Front panel standard operating mode 8 Standby button 8 Volume Button 8 Profile selection buttons P1 P2 amp P3 9 Use of the Re
8. three cables to a single amplifier 30 DEQX HDP 4 Users Manual Specification Mains input voltage 100 240VAC 50 60Hz Power consumption 60VA Dimensions Height 2U 97mm Depth 325mm Width 430mm Signal to Noise Ratio 107 dB A weighted Total Harmonic Distortion 0 00045 Analogue input maximum levels Balanced 17 dBu differential 5 5 Vrms Unbalanced Default Level 9 dBu 2 2 Vrms Maximum Level 13 dBu 3 5 Vrms Analogue output maximum levels Balanced Default Level 12 dBu differential 3 0 Vrms Minimum Level 8 dBu differential 2 0 Vrms Maximum Level 21 dBu differential 8 8 Vrms Unbalanced Default Level 6 dBu 1 5 Vrms Minimum Level 2 dBu differential 1 0 Vrms Maximum Level 15 dBu 4 4 Vrms Crossover slope software selectable up to 300dB octave Latency from 2 33ms depending on filter configuration AID converter 24 bit 96kHz D A converters 32 bit 192kHz Microphone 48V bias Digital inputs S PDIF or AES EBU or Optical PC connections USB or RS232 Input Impedance Balanced and Unbalanced 50 kohms Output Impedance Balanced 150 ohms Output Impedance Unbalanced 75 ohms into an earth referenced amplifier i e one where the RCA GND pin connects to mains ground This is normally the case It is 75 ohms plus 75 ohms in parallel with whatever the amplifier puts in series between its RCA connector and mains ground If this is open then the impedance can be as high as
9. user to the presence of important operating and maintenance instructions in the literature accompanying the product The lightning with arrowhead symbol within a triangle is intended to alert the user to the presence of un insulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to person DEQX HDP 4 Users Manual 3 Important Safety Instructions Read these instructions entirely before installing or operating this product Keep these instructions Heed all warnings Follow all instructions Do not use this product near water Clean only with a dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat source such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the grounding type safety plug A grounding type plug has two blades and a third grounding prong or blade The third prong or blade is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at the plug and the point where the cord exits from this product Do not use this product with a damaged cord or plug Only use attachments and accessories specified by
10. 150 ohms two pin power connector Due to our policy of continuous product improvement the above specifications may change without notice DEQX HDP 4 Users Manual Installation Information 31 Installer Date Serial Number Profile 1 Front panel button 3 Profile 2 Front panel button 4 Profile 3 Front panel button 5 Profile 4 Any 2 front panel profile buttons Speaker 1 configuration Speaker 2 configuration Speaker 3 configuration Speaker 4 configuration Speaker 5 configuration Speaker 6 configuration Single Amp Bi Amp Tri Amp Subwoofer Single Amp Bi Amp Tri Amp Subwoofer Single Amp Bi Amp Tri Amp Subwoofer Single Amp Bi Amp Tri Amp Subwoofer Single Amp Bi Amp Tri Amp Subwoofer 32 DEQX HDP 4 Users Manual Additional notes DEQX HDP 4 Users Manual 33 Speaker room layout diagram We suggest that you number speakers on this diagram to match corresponding entries in the Installation Information table above 34 DEQX HDP 4 Users Manual Connection diagram DEQX HDP 4 Users Manual 35 Installation Warranty 36 DEQX HDP 4 Users Manual Index Advanced EQ 11 12 AES EBU 14 18 30 Analogue input 8 16 30 Bi amp 27 29 Bi amplified 23 Bi wired 22 29 Crossovers 21 Digital input 8 16 IEC mains socket 18 IO configuration 15 16 Microphone 16 17 30 Profile 9 14 15 31 RS232 17 18 30 Single amp 26 29 Single wired 20 22 29
11. DEQX HDP 4 User s Manual Professional Digital Correction for Installers and End Users e e e P amp e f DEQX vore e e o e e e o o e HDP4 speaker room calibration processor e HDP4 speaker room calibration processor DIGITAL OUTPUTS Low wo 2 DEQX HDP 4 Users Manual Copyright 2012 DEQX Pty Ltd DEQX Calibrated is a trademark of DEQX Pty Ltd All other product or brand names may be trademarks or registered trademarks of their respective owners Disclaimer and Limitation of Liability DEQX Pty Ltd assumes no responsibility for loss or damage resulting from the use of its products Please refer to the license supplied with the DEQX Calibration software Warning To prevent fire or shock hazard do not expose the unit to rain or moisture To avoid electrical shock do not open the unit No user serviceable parts are inside Please refer any servicing to qualified personnel Caution Damage may result to your speaker drivers and other equipment if your audio system is connected incorrectly or if the unit is used incorrectly Read this user manual in full before configuring your hardware and refer to your speaker manufacturer s specifications to ensure correct connection If you are in doubt as to as the connection of your audio equipment please seek assistance from a professional audio installer or contact DEQX at support degx com gt P The exclamation point within a triangle is intended to alert the
12. Speaker configuration 19 Speaker connection 24 Speaker placement 19 Speaker wiring 21 Specification 30 Tri amp 28 29 Tri wired 20 23 29 Volume 8 11 16
13. Tri Amp configuration Note that it is preferable that the speaker s internal crossover be disconnected in this configuration 24 DEQX HDP 4 Users Manual Choosing a configuration Using individual amplifier channels for each driver results in improved sound quality It also offers the opportunity to take advantage of DEQX digital crossovers bypassing the speaker internal crossover Some speakers offer a choice of wiring By adding links to or removing links from wiring terminals on the speaker you can choose single wiring bi wiring or tri wiring Refer to the speaker manufacturer s specification to ensure correct connection For bi amplified or tri amplified configurations additional amplifier channels are required Speaker connection A large variety of configurations are possible Sample configurations shown demonstrating options available using a single DEQX unit with stereo speakers The illustrations below show single amp bi amp and tri amp configurations using the RCA unbalanced audio outputs For a description of the DEQX unit connectors see Rear panel on page 17 The table below shows the signal present at each DEQX unit rear panel connector in each possible configuration Left channel outputs are numbered L 1 L3 and right channel outputs R1 R3 Left and right inputs are named L and R respectively Output Speaker Configuration Single Amp Bi Amp Tri Amp Subwoofer Low L1 left No connection No conne
14. Yellow Red Red Blue Red Blue be powered off and on to recover Debug Red Blue information regarding the fault can be sent to DEQX for analysis Rear panel connections The rear panel houses the power switch connectors for the configuration PC and digital and analogue audio input and output The rear panel also provides a connector for the microphone used in calibration USB The USB port is used for connecting a PC to the unit during initial installation and configuration The RS232 serial port is provided as an alternative option USB Audio USB audio connector is used when the HDP 4 or HDP Express II are fitted with the optional USB 12S convertor is installed Digital In 1 Toslink optical digital audio input connection between your pre amp or source 18 DEQX HDP 4 Users Manual unit and the DEQX unit Digital In 2 BNC S PDIF digital audio input connection between your pre amp or source unit and the DEQX unit Digital In 3 RCA S PDIF digital audio input connection between your pre amp or source unit and the DEQX unit Digital In 4 AES EBU Digital audio input connection between your pre amp or source unit and the DEQX unit RS232 Standard serial connector used for connecting a PC to the unit during initial installation and configuration The USB serial port is provided as an alternative option The lower RS232 port is currently not supported Mic Used during installation to connect a microphone to
15. a DEQX speaker configuration corresponding to a bi wired speaker connected to two separate amplifier channels Bi amped speakers may have their internal passive crossovers by passed Bi wired A speaker configuration in which two cables connect the speaker to a single amplifier Crossover a device for limiting the frequencies to each driver in a speaker Crossover Frequency the frequency at which a crossover operates Driver One of the electro mechanical cone or ribbon speakers located in a speaker cabinet HDP High Definition Processor The DEQX CalibratedTM HDP 4 Processor is a 2 input 6 output digital processor offering individual driver correction high order digital crossovers and room correction parametric equalisation Single amp a DEQX speaker configuration corresponding to a single amplifier channel connected to a speaker in a single wired bi wired or tri wired configuration Single wired A speaker configuration in which a single cable connects the speaker to a single amplifier Speaker A loudspeaker cabinet containing one or more drivers Subwoofer a DEQX speaker configuration corresponding to a subwoofer connected to a single amplifier channel Tri amp a DEQX speaker configuration corresponding to a tri wired speaker connected to three separate amplifier channels Tri amped speakers may have their internal passive crossovers by passed Tri wired A speaker configuration in which the speaker is connected by
16. band For example if you have pressed the Mid button the Gain and Gain buttons will affect the Mid band until either the Low or High button is pressed Every time you press an EQ button you get feedback on the front panel The 3 rightmost buttons will light up green for 1 second Depending on which control is active low mid or high one of the lights will be brighter than the others the P1 light will be brighter when the low control is active the P2 light will be brighter when the mid control is active the P3 light will be brighter when the high control is active To reset the boost of the active band press the Gain OdB button To reset the boost of all the bands press the EQ Reset button 12 DEQX HDP 4 Users Manual Advanced EQ The EQ controls on the remote control allow the user to store and retrieve up to 100 EQ profiles each consisting of up to three EQ settings The EQ profiles are not the same as the four correction profiles P1 P2 P3 and bypass which can be stored on the unit Outline of the EQ controls There are 100 profiles numbered 00 to 99 There are 3 bands of EQ bass mid treble The bass and treble controls have adjustable gain and frequency The mid control has adjustable gain frequency and Q Q refers to the width of the EQ effect in octaves Q can be 10 options from 1 12th octave to 4 octaves Refer to the table of Q quicksets on the remote control Frequency can be any
17. ction Left Woofer Left Sub Low R1 right No connection No connection Right Woofer Right Sub Mid L2 left Left Speaker Left Woofer Left Mid range No connection Mid R2 right Right Speaker Right Woofer Right Mid range No connection High L3 left No connection Left Tweeter Left Tweeter No connection High R3 right No connection Right Tweeter Right Tweeter No connection DEQX HDP 4 Users Manual 25 The table below lists the configurations and shows the connections for each channel When using multiple DEQX units for home cinema applications these connections may not be the correct and the actual loudspeaker connected to a channel will depend on the installation DEQxX unit configuration Allocated Output L Channels R Channels Single Amp with Stereo Subwoofers L2 Left Speaker L1 Left Subwoofer R2 Right Speaker R1 Right Subwoofer Single Amp with Mono Subwoofer L2 Left Speaker L1 Left Subwoofer R2 Right Speaker R1 Same as L1 Bi Amp with Stereo Subwoofer L3 Left Tweeter L2 Left Woofer L1 Left Subwoofer R3 Right Tweeter R2 Right Woofer R1 Right Subwoofer Bi Amp with Mono L3 Left Tweeter R3 Right Tweeter Subwoofer L2 Left Woofer R2 Right Woofer L1 Left Subwoofer R1 Same as L1 Tri Amp L3 Left Tweeter R3 Right Tweeter L2 Left Mid range L1 L
18. eft Woofer R2 Right Mid range R1 Right Woofer When you have determined the optimum speaker connection and configuration record it in a diagram in the space provided in this manual See nstallation Information on page 31 26 DEQX HDP 4 Users Manual Single amp The diagram shows stereo speakers each in a single amp configuration with optional subwoofers This uses up to four DEQX unit output channels DEQX PDC oN o X4 jee o un QUO QO mo ee on d Qc OO0O08ees OOOOOO ameo EE ome T V Stereo Power Amplifier I IE Optional Stereo Sub Bass Amplifier Ys DEQX HDP 4 Users Manual 27 Bi amp The diagram shows stereo speakers each in a bi amp configuration with optional subwoofers This uses up to six DEQX unit output channels DEQX PDC oo e TA ee o Oo Q o_o o e o zi O j OO Jarot QOO OOQQOQO wd mer Lo lt lt l une ie d anush ma eee 4 Channel Power Amplifier Optional Stereo Sub Bass Amplifier Oo i ORO 28 DEQX HDP 4 Users Manual Tri amp The diagram shows stereo speakers each in a tri amp configuration This uses six DEQX unit output channels DEQX PDC ee Ee b ini Kl ae oo W 5899 teten Od geei OOQOOOO 6 Channel Power Amplifier Hmmm DEQX HDP 4 Users Manual 29 Glossary Bi amp
19. eps for professional installers are Determine the required speaker placement See below Determine the required speaker configuration See below Connect the components according to the chosen speaker configuration Seeon page 24 The next phase of installation is software configuration This involves setting up profiles for your configuration room and primary listening position The unit can produce output without software configuration using the factory settings See Factory Settings on page 15 However the output will be optimized for your speakers or room only after software configuration has been successfully completed Refer to the DEQX Calibration Software Manual for software configuration details Determining speaker placement Speaker placement within a room can have a dramatic effect on the overall sound quality If DEQX s parametric equalizer has been used to reduce room effects it is important to leave the room and speakers configured as they were when the room measurement was made When you have determined the optimum speaker placement record it in a diagram in the space provided in this manual under Speaker room layout diagram on page 33 Determining speaker configuration Configurations vary according to the number of speakers the number of drivers in each speaker the type of crossover in each speaker speaker wiring single wiring bi wiring or tri wiring See the topics below for details Depe
20. es or enables operation of the unit When the unit exits standby mode the last selected profile setting remains selected Together with button 5 this also selects IO Configuration mode Button light indicates state as follows White Clipping signal overloaded analog input or digital or analog output Volume Button Press the upper button to increase the volume Press the lower button to decrease the volume Each press increments or decrements in 1dB steps from OdB to above 24dB then in 2dB steps above 36dB then in 3dB steps above 48dB then in 6dB steps down to 120dB The volume setting is saved when the unit is placed into standby or powered down DEQX HDP 4 Users Manual 9 The button light indicates the gain as follows Purple Pink From 20 dB to 10 dB White From 10 dB to 0 dB The volume button light will flash when the unit is muted except when the gain is below 60 dB The unit can be muted with the software ie with a PC connected with either digital or analogue input selected Furthermore if digital input is selected but the unit does not detect a digital signal as will usually happen if a CD player is paused the unit will automatically go into mute mode Profile selection buttons P1 P2 amp P3 These three buttons select stored calibration profiles for operation Pressing any two profile buttons together selects a fourth profile typically set up as a bypass profile to pas
21. mote Control 10 Mute 10 Standby 10 Volume 11 EQ 11 Advanced EQ 12 Input Select 14 Profile Select 14 User 14 Batteries 14 Factory Settings 15 Front panel IO configuration mode 15 Volume 16 P1 Analogue input selection 16 P2 Microphone selection 16 IO configuration notes 16 Front panel button light special modes 17 Rear panel connections 17 DEQX HDP 4 Users Manual Installation Determining speaker placement Determining speaker configuration Number of speakers Number of drivers in each speaker Crossovers Speaker wiring and amplifier connection Single wired Tri wired Bi amplified Choosing a configuration Speaker connection Single amp Bi amp Tri amp Glossary Specification Installation Information Additional notes Speaker room layout diagram Connection diagram Installation Warranty Index 19 19 19 20 20 21 21 22 23 23 24 24 26 27 28 29 30 31 32 33 34 35 36 6 DEQX HDP 4 Users Manual Unpacking the unit Carefully remove the unit and the accessory kit from the shipping carton Check visually for shipping damage Contact both the shipper and DEQX immediately if the unit or any of the accessories bear any sign of damage from mishandling All DEQX equipment is carefully inspected before leaving our factory Keep the shipping carton and packing materials for future use or in the unlikely event that the product needs servicing If the product is shipped without the original packaging damage c
22. nding on these factors choose for each speaker a DEQX Speaker configuration according to the following table 20 DEQX HDP 4 Users Manual Speaker Wiring DEQX Speaker Uses Speaker Internal Users DEQX Digital Configuration Crossover Crossover Single wired Single Amp YES NO Bi wored Single Amp YES NO Bi Amplified Bi Amp Optional depends on YES model Tri wired Single Amp YES NO Tri Amplified Tri Amp Optional depends YES on model Single wired Subwoofer Optional depends YES on model For example if you have a stereo system consisting of two bi amped speakers and a subwoofer you would choose the Bi Amp DEQX speaker configuration for each of the bi amped speakers and the Subwoofer configuration for the subwoofer More details are given in the DEQX Installer s Manual and online help Number of speakers In this document the word speaker refers to loudspeaker cabinet A stereo configuration has left and right speakers with optional subwoofer A home theatre configuration usually has four or five loudspeakers plus one or two subwoofers Number of drivers in each speaker In this document the word driver refers to an electro mechanical speaker cone dome ribbon or horn unit within a speaker cabinet For example a speaker may contain a tweeter driver a midrange driver and a woofer driver with a crossover circuit that distributes low frequencies bass to the woofer middle frequencies to
23. ould occur and void the warranty Accessories You should find the following in the accessory kit One 1 AC mains cord One 1 USB cable One 1 microphone lead Only with Calibration Kit One 1 CD ROM with the DEQX Calibration software One 1 measurement microphone microphone holder Only with Calibration kit One 1 remote control Two 2 AAA batteries One 1 User s manual and the Installers Manual are located on the DEQX CD About this manual This manual is intended for both installers and users The HDP 4 Express Mk2 For simplicity in this manual both models are referred to as the DEQX unit Please read this manual in full before installing or using the DEQX unit Installers should also read the DEQxX Calibration Installer s Manual The manual provides comprehensive details and operating instructions for all the features of the DEQX unit Installers should record information specific to the Installation Information on page 31 Users should refer to Installation Information on page 31 for information specific to their installation recorded by the installer DEQX HDP 4 Users Manual 7 Introduction DEQX CalibratedTM Digital EQualization and X over Calibrated is a DSP Digital Signal Processing technology that corrects frequency response and time alignment errors in loudspeakers The HDP High Definition PDC PDC Professional Digital Calibration units take the signal from the signal source possibly via
24. s signals through the unit unchanged Users please refer to Installation Information on page 31 to determine how your installer set up these three profiles Installers please record installation information in the space provided in Installation Information Please refer to Factory Settingson page 15 for the profile default settings Button lights indicate state as follows All off Unit is not in filtering mode Refer to standby light to determine mode All Yellow No filter profiles are loaded All lights white Bypass mode Profile 0 selected Only one button light white Profile corresponding to this button is active 10 DEQX HDP 4 Users Manual Use of the Remote Control The remote control supplied with the Express Mk2 and the HDP 4 controls a number of functions of the unit Refer to the figure below Standby Volume Button Mute Parametric EQ Quicksets EQ Buttons x Xm n D ne Input Selection Buttons EQ Frequency amp Q quickset table Profile Selection Buttons Mute The mute button mutes and unmutes the output of the unit Press the Mute button to mute the output press it again to turn mute off When mute is on the volume light on the unit front panel flashes Standby The Standby button puts the unit in and out of standby in the same manner as the Standby 1 0 button on the unit front panel When in standby the light on the Standby button on the unit front panel is red
25. t Default Remote EQ Frequency amp Bandwidth Settings Magri tude dB Phase degrees Frequency Hz To reset all 3 tone controls to their defaults use EQ Reset This doesn t affect saved EQprofiles Every time you do an EQ operation you get feedback on the front panel The 3 rightmost buttons will light up green for 1 second Depending on which control is active low mid or high one of the lights will be brighter than the others the P1 light will be brighter when the low control is active the P2 light will be brighter when the mid control is active the P3 light will be brighter when the high control is active The DEQX unit has a total of 10 eq settings per correction profile 3 of these are reserved for the remote control s EQ controls and 7 are reserved for the parametric EQ accessible from the DEQX Cal software There is an option to disable the remoteEQ and use 10 bands of parametric EQ instead If this option is turned on then the EQ controls cannot be used 14 DEQX HDP 4 Users Manual Input Select There are eight input selection buttons A1 this selects analogue RCA unbalanced as the input source A2 this selects analogue XLR balanced as the input source D1 this selects digital Toslink Otpical as the input source D2 this selects digital BNC also known as SPDIF as the input source D3 this selects digital RCA also known as SPDIF as the input source D2 this selec
26. the midrange driver and high frequencies treble to the tweeter DEQX HDP 4 Users Manual 21 High frequency tweeter driver Mid frequency midrange driver Low frequency woofer driver Crossovers A crossover is a device for limiting the frequencies to each driver in a speaker A two way crossover operates at a single crossover frequency A low pass filter passes frequencies below the crossover frequency to one driver A high pass filter passes frequencies above the crossover frequency to the other A three way crossover divides the frequencies three ways at two crossover frequencies Crossovers may be passive requiring no external power source or active requiring an external power source Speakers with multiple drivers typically contain crossovers to distribute frequencies to the internal drivers A speaker may offer the option of bypassing the internal crossover and using an external crossover such as the DEQX PDC or HDP3 This requires additional amplification channels See Speaker wiring and amplifier connection below Speaker wiring and amplifier connection Speakers containing more than one driver may be wired in a variety of ways depending on how amplifiers are connected to individual speaker drivers A bi wired speaker has two separate cables for amplifier connection The cables can be connected in parallel to a single amplifier single amplified or a separate amplifier for each 22 DEQX HDP 4 Users Manual
27. ts digital XLR balanced also known as AES EBU as the input source USB this selects the optional USB Audio input if installed as the input source Auto this switches between the last selected analogue source and the last selected digital source It will use the digital source if there is a signal received at the digital input otherwise it will use the analog source For example if you were to press the An A1 or A2 button then the D2 button then press the Auto button the unit will use the digital D2 BNC signal if there is one regardless of whether there is an analogue RCA signal or not and use the analogue RCA signal if there is no digital D2 signal Profile Select There are four profile selection buttons Bypass P1 P2 and P3 These correspond to the four profiles that can be stored on the unit and selected using the profile selection buttons on the unit front panel User This button is for a user defined function This button is currently not functional Its functionality will be available through a future software upgrade Batteries The remote control takes two AAA size batteries supplied with the remote control The battery compartment is in the top of the remote control To install the batteries open the battery cover at the back of the remote control by sliding it upwards as indicated by the arrow on the battery cover Install the batteries with and signs matching the and signs of the figures in the compartment
28. value in the range 20 Hz to 24 kHz in semitone steps You can also quickly jump from one frequency to another using the quicksets as listed on the remote control Gain is 12dB in 1dB steps Using the EQ controls When you set the EQ controls they are independent of the correction profiles i e they remain like that for every correction profile P1 P2 P3 Bypass They will stay the same even if you turn off the power You can save the current EQ controls into an EQprofile using SAVExx For example pressing SAVExx then 5 then 7 saves the current EQ controls into EQprofile 57 You can load EQ controls from a previously saved EQprofile using EQxx For example pressing EQxx then 0 then 5 loads EQprofile 05 into the current EQ controls Note two digits are required to save or load an Eqprofile There is an active EQ tone control which is either bass mid or treble You select this by choosing Low Mid or High This controls what the Gain Gain Freq Freq Qx and Gain OdB buttons do To reset the gain of a single control to OdB press Gain OdB This applies to the active tone control The default settings for the 3 bands are Low 110Hz Mid 440Hz 1 Octave bandwidth High 3500Hz DEQX HDP 4 Users Manual 13 The figure below shows the 3 tone controls in their default settings each with 6 dB of boost Also shown are the phase consequences of the default settings with 6 dB of boos
Download Pdf Manuals
Related Search