NF3A User`s Manual Revision 2.0
Contents
1. RJ 45 LAN Port 3 aja ole PS2KBMS Header Full size rim Mini PCIE mSATA Slot RJ 45 LAN Port DDR3L Es E X CI SODIMM Slot USB 2 0 Ports Power Switch Button 24V DC Reset Button Power in Connecto mu GT MM LANLED Headers Internal Diagram Back Side Jumper Position 2 i ala Ola ale us i lel uum Jumper Jumper Name _ Description Security Measure Function Select Connectors Connector Header Pin9 Function Select 4 Pin Block Headers Header Description P SMBUS SMBUS Header 4 pin Block PS2KBMS PS2KBMS Header FP Front Panel Header PWR LED 8 pin Block HDD LED Power Button Reset LAN1LED LAN2LED LAN Activity LED Headers 2 pin Block LVDS 24 bit LVDS Header 30 pin Block Chapter 2 Hardware Installation 2 1 Jumper Setting 1 JP1 4 pin LVDS PVCC 3 3V 5V 12V Function Select JP1 LVDS 1 2 1 2 3 4 3 4 5 6 5 6 2 4 Closed LVDS 3 4 Closed LVDS VCC 3 3V VCC 5V JP2 INVERTER me T 1 2 3 4 5 6 4 6 Closed LVDS VCC 12V 1 2 Closed Inverter VCC 5V 2 3 Closed Inverter VCCz 12V 3 JP3 4 SN Header Pin9 Function Select 2 4 Closed RI RS232 2 4 Clo2. Auto To disable legacy support if no USB devices are connected XHCI Hand off This is a workaround for OSes without XHCI hand off support The XHCI ownership change should be claimed by XHCI driver The optional settings are Enabled Disabled EHCI Hand off This is a workaround for OSes without EHCI hand off support The EHCI ownership change should be claimed by EHCI driver The optional settings are Disabled Enabled USB Mass Storage Driver Support The optional settings are Disabled Enabled USB hardware delay and time outs USB Transfer time out Use this item to set the time out value for control bulk and interrupt transfers The optional settings are 1 sec 5 sec 10 sec 20 sec Device reset time out Use this item to set USB mass storage device start unit command time out The optional settings are 10 sec 20 sec 30 sec 40 sec Device power up delay Use this item to set maximum time the device will take before it properly reports itself to the host controller Auto uses default value for a root port it is 100 ms for a hub port the delay is taken from hub descriptor The optional settings Auto Manual Select Manual you can set value for the following sub item Device Power up delay in seconds Device Power up delay in seconds The delay range is from 1 to 40 seconds in one second increments 36 gt Reltek GBE Family Controller MAC XX XX XX XX XX XX Use t
3. Th Select Item Enter Select Change Opt FI General Help Fer Previous Values F3 Optimized Defaults Savo A Exit ESCI Exit ACPI Settings ACPI Sleep State Use this item to select the highest ACPI sleep state the system will enter when the suspend button is pressed The optional settings are Suspend Disabled 53 Suspend to RAM Wakeup Function Settings Press Enter to make settings for the following sub items Wake System with Fixed Time Use this item to enable or disable system wake on alarm event When set as Enabled system will wake on the hour min sec specified PS2 KB MS Wakeup The optional settings Disabled Enabled Use this item to enable or disable PS2 KB MS wakeup from S3 S4 S5 state This item will only show when ERP Support is set as Disabled Super Configuration Press Enter to make settings for the following sub items Super IO Confiquration Serial Port 1 Configuration Press Enter to make settings for the following items Serial Port Use this item to enable or disable serial port COM Change Settings Use this item to select an optimal setting for super IO device Transmission Mode Select The optional settings are 5422 RS232 RS485 Mode Speed Select The optional settings are RS232 RS422 RS485 250kbps RS232 1 Mbps RS422 RS485 10Mbps Serial Port FIFO Mode The optional settings are 16 Byte FIFO 32 Byte FIFO 64 Byte FI
4. in the Flash Descriptor Override 2 2 Connectors and Headers 2 2 1 Connectors 1 Rear l O Connectors RJ 45 LAN Ports USB 2 0 Ports DVI I Port 9V 24V DC Power in Connector Line Out Port USB 3 0 Ports USB 2 0 Ports 2 SATAII Port connector SATA1 SATA1 port is a high speed SATAII port that supports 3GB s transfer rate Pin No s 7 3 SATA Power Connector 4 pin PWOUT lk EE z ATI ASt 1 Control Fan Clock VCC Pin1 GND Definition Backlight Enable Backlight PWM PVCC PVCC 1 Backlight Up SW Backlight Down SW Z Z U JU 2 2 2 Headers 1 FP AUDIO 9 pin Line Out MIC In Header connects to Front Panel Line out MIC In connector with cable Lineout R NC Lineout L 2 SPDIFOUT 2 pin SPDIF Header 2 a SPDIFOUT 3 COM4 3 2 1 9 pin S RS422 RS485 for COM1 for COM1 TX COM cable for RS422 or RS 485 function User also needs to go to BIOS to set Transmission Mode Select for refer to Page 28 17 4 GPIO 10 pin GPIO Header 6 SMBUS 4 Pin zi BUS Header SMBUS DATA GND SMBUS CLK Pin 155 VCC S DATA MS CLK GND B CLK KB DATA Pin 1 8 FP 8 pin Front Panel Header GND GND PWRBTN RSTSW PWRLED HDDLED PWRLED HDDLED E Pin 1 LED P
5. PXE Boot Support When set as Disabled 4 boot optional will not be created Ipv6 PXE Support The optional settings are Disabled Enabled Use this item to enable PXE Boot Support When set as Disabled lpv4 boot optional will not be created PXE boot wait time Use this item to set wait time to press ESC key to abort the PXE boot CSM Configuration Press Enter to make settings for the following sub items Compatibly Support Module Confiquration Option ROM Message The optional settings are Force BIOS Keep Current INT19 Trap Response The optional settings are Immediate Postponed Option ROM execution order Network This item controls the execution of UEFI and legacy PXE OpROM The optional settings are Do not launch UEFI only Legacy only Storage This item controls the execution of UEFI and Legacy Storage OpROM The optional settings are Do not launch UEFI only Legacy only Legacy first UEFI first Other PCI devices This item determines OpROM execution policy for devices other than Network storage or video The optional settings are first Legacy Only USB Configuration Press Enter to make settings for the following sub items USB Configuration 35 Legacy USB Support The optional settings are Enabled Disabled Auto Enabled To enable legacy USB support Disabled To keep USB devices available only for specification
6. confirm or to modify Press lt Enter gt to select Press lt gt lt gt keys when you want to modify the BIOS parameters for the active option F1 General help F2 Previous value F3 Optimized defaults F4 Save amp Reset Press Esc to quit the BIOS Setup 3 4 Getting Help Main Menu The on line description of the highlighted setup function is displayed at the top right corner the screen Status Page Setup Menu Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item To exit the Help Window press lt ESC gt 3 5 Menu Bars There are six menu bars on top of BIOS screen Main To change system basic configuration Advanced To change system advanced configuration Chipset To change chipset configuration Security Password settings Boot To change boot settings Save amp Exit Save setting loading and exit options User can press the right or left arrow key on the keyboard to switch from menu bar The selected one is highlighted 3 6 Main Menu Main menu screen includes some basic system information Highlight the item and then use the lt gt lt gt and numerical keyboard keys to select the value you want in each item BIOS Informat ton BIOS Vendor Core Version Bulld Date and Time Sustem Time Access Level System Date Aptio Setup Utility 411 Got the
7. number of seconds to wait for setup activation key Bootup Numlock State Use this item to select keyboard numlock state The optional settings are On Off Quiet Boot The optional settings are Disabled Enabled Boot Option Priorities Boot Option The optional settings are UEFI Built in EFI Shell Disabled 3 11 Save amp Exit Menu Aptio Setup Utility Reset the system after saving Discard Changes and Reset the changes Restore Defaults Save as User Dafaults Restore User Defaults Boot verr Bullt in EFI Shell Launch EFI Shell from filesystem device b Reset Sust m wlth disable Mode Select Screen Th Select Item Ent ri Select Changa Opt Fi General Help F21 Previous Values F3 Optimized Defaults F4 Savo A ESCE Exit Save Changes and Reset This item allows user to reset the system after saving the changes Discard Changes and Reset This item allows user to reset the system without saving any changes Restore Defaults Use this item to restore load default values for all the setup options 42 Save as User Defaults Use this item to save the changes done so far as user defaults Restore User Defaults Use this item to restore defaults to all the setup options Boot Oerride UEFI Built in EFI Shell Press this item and a dialogue box shall appear to ask if user wish to save configuration and reset Lauch EFI Shell f
8. 0 x 1024 24bit Dual 1366 x 768 18bit Single 1366 x 768 24bit Single 1440 x 900 18bit Dual 1440 x 900 24bit Dual 1400 x 1050 24bit Dual 1600 x 900 24bit Dual 1680 x 1050 24bit Dual 1600 x 1200 24bit Dual 1920 x 1080 24bit Dual South Bridge Press Enter to further setting USB device configuration gt Azalia HD Audio Press Enter to further setting USB device configuration Audio Confiquration Audio Controller The optional settings are Disabled Enabled Azalia HDMI Codec Use this item to enable or disable internal HDMI codec for Azalia 38 The optional settings are Disabled Enabled USB Configuration Press Enter to make settings for the following sub items USB Confiquration USB 3 0 Support The optional settings are Auto Disabled USB 3 0 Link Power Management The optional settings are Enabled Disabled USB 2 0 Support The optional settings are Auto Disabled This item may or may not show up depending on different configuration MPE Slot Speed The optional settings are Auto Gen2 Gen1 MPE Controller The optional settings are Enabled Disabled Speed The optional settings are Auto Gen2 Gen1 Onboard Lan1 Controller The optional settings are Enabled Disabled Onboard Lan2 Controller The optional settings are Enabled Disabled Restore AC Power Loss Use this item to select AC power state when power is re applied after
9. BIOS ENTERING SETUP X MM 22 22 BIOS MENU SCREEN a genu A aaa BE a aapa ana a aga a 23 93 TENGIONISE YS sasae aana naa uu uu us 24 et 24 209 DANO lt DEN 25 35 MENU 26 ADVANGED MENU esse sia E ija aja a ara KON 27 CHIPSET MENU aa e ae a a ea e agan a e an BAN a ADA E AGA ENE 37 99 SEGURITY MENU 4 aaa aaa alane aa ea paja ang aa a maa ae aan a pan a a uu NIMM 40 3 10 das RAN EAE AN je aja ee eines ine i DUE 41 SAVE amp EXIT MENU sie en a ARCU kaa a a aaa aga 42 iii Environmental Safety Instruction Avoid the dusty humidity and temperature extremes Do not place the product in any area where it may become wet 0 to 60 centigrade is the suitable temperature The figure comes from the request of the main chipset Generally speaking dramatic changes in temperature may lead to contact malfunction and crackles due to constant thermal expansion and contraction from the welding spots that connect components and PCB Computer should go through an adaptive phase before it bo
10. Date Use to American Megatrends switch between Date elements 5 009 02 26 2014 15152140 01 2014 00 16 61 hdministratoi Select Screen 11 Select Item Enter Select Change Opt F1 General Help Previous Values Optimized Defaults Fai Save 4 ExIt ESCE EXIT Set the date Please use Tab to switch between data elements System Time the time Please use Tab to switch between time elements 3 7 Advanced Menu b gt k k k b gt gt k b k k T hptio Setup Utility 08 Selection Hindous 8 ACPI Settings Hakeup function Settings Super 10 Conf Igurat Lon SmartFAN Conf igur t Lon FC Health Status Shutdown Temperature Configuration Serial Port Console Redirection CPU Configuration PPM Conf 1gurat Lon SATA Conf Igurat Lon Network Stack Configuration CSM Configuration USB Configuration Realtek PCIe Family Controller MAC 18100105131 Realtek PCIe GPE Family Controller MAC 100130 181001051233 ERP Function The optional settings Auto Disabled This item should be set as Disabled if you wish to have all active wake up functions OS Selection The optional settings Windows 8 X Windows 7 gt ACPI Settings Press Enter to make settings for the following sub item Energy Related Products tunet Lon Disable to active all functions 4 Select Screen
11. FO 128 Byte FIFO gt Serial Port 2 Configuration Serial Port 3 Configuration Serial Port 4 Configuration Press Enter to make settings for the following items Serial Port Use this item to enable or disable serial port COM Change Settings Use this item to select an optimal setting for super IO device Serial Port FIFO Mode The optional settings are 16 Byte FIFO 32 Byte FIFO 64 Byte FIFO 128 Byte FIFO WatchDog Timer Use this item to enable or disable WatchDog Timer Control When set as Enabled the following sub items shall appear WatchDog Timer Value User can set a value in the range of 4 to 255 WatchDog Timer Unit The optional settings are Sec Min WatchDog Wake up Timer in ERP This item support WDT wake up while ERP function is set as Disabled The optional settings are Enabled Disabled When set as Enabled the following sub items shall appear WatchDog Timer Value in ERP User can set a value in the range of 10 to 4095 WatchDog Timer Unit The optional settings are Sec Min ATX Power Emulate AT Power 29 This item support Emulate AT power function MB power On Off control by power supply Use needs to select AT or ATX Mode on MB jumper at first ATX Mode amp AT Mode Select Case Open Detect This item controls detect case open function The optional settings are Enabled Disabled SmartFan Configuration Press Enter to make settings for SmartFa
12. NESS AND THE LIKE PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER S BENEFIT WITHOUT INTENT TO INFRINGE Manual Revision Information Reversion Revision History Date 2 0 Second Edition June 20 2014 Item Checklist Motherboard User s Manual CD for motherboard utilities Cable s 1 1 Chapter 1 Introduction of the Motherboard Feature of Motherboard Onboard Intel Bay Trail Series Processor with low power consumption never denies high performance Support single channel DDRIIIL 1333 MHz SODIMM up to 8GB Support 1 SATAII device Onboard one full size mSATA Mini PCIE slot Onboard one half size Mini PCIE slot Onboard 2 RJ 45 gigabit Ethernet LAN port Integrated with 1 24 bit dual channel LVDS header Support DVI I output Support USB 3 0 data transport demand Support CPU Smart FAN Compliance with ErP standard Support Watchdog function 1 2 Specification Spec Design e 3 5 SBC 6layers PCB size 14 8x 10 2 cm 2930 8 NF3AB 2930 Series Intel Bay Trail M N2930 SoC CPU Embedded 2807 amp NF3AB 2807 Series Intel Bay Trail M N2807 CPU SoC CPU 3827 8 NF3AB 3827 Series Intel Bay E3827 SoC CPU 1 DDRIIIL SODIMM Sl
13. User Manual For Intel Bay Trail Series CPU Based 3 5 SBC Revision 2 0 Release date June 20 2014 Trademark Specifications and Information contained in this documentation are furnished for information use only and are subject to change at any time without notice and should not be construed as a commitment by manufacturer Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding To minimize pollution and ensure environment protection of mother earth please recycle TABLE OF CONTENT ENVIRONMENTAL SAFETY INSTRUCTION nnn iv USER gt NOTICE 2 ana ena nas nama a Kaja a GN 2 V MANUAL REVISION INFORMATIONN 1 V IEM Ee edEipp V CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD Tt FEATURE OF MOTMER BOARD ginanda nan usa 2 1 1 2 SPECIFICATION anana 2 1 3 LAYOUI DIAGRAM escis aaa naa babe N en 3 CHAPTER 2 HARDWARE INSTALLATION 2 1 JUMPER SETTING c 9 2 2 CONNECTORS AND 65 1 1 14 225 CONNECTORS L a Pen ajaa a MINNS MEE 14 22 2 HE DEKRS BN Aa 16 CHAPTER 3 INTRODUCING
14. a power failure The optional settings are Power Off Power Last State 3 9 Security Menu Aptio Setup Utility A Passuord Descr ipt lon Set Administrator Passuord If ONLY the Administrator s password 5 set then this only Limits access to Setup and 15 only asked for when entering Setup If ONLY the User s password 16 set than this 15 a power on password and must be entered to boot or enter Setup In Setup the User will have Administrator rights he password length must be in the following range Minimum length Maximum length 4 Select Screen Th Select Item Enter Select User Password k 1 Change Opt F1 General Help Fet Previous Values Optimized Defaults F4 Save A Exit ESC LODS AA MUTA oecurity menu allow users to change administrator password and user password settings 40 3 10 Boot Menu Boot Conf igur t Lon Bootup NumLock State Quiet Boot Boot Optlon Prior it las Boot Option 1 Boot Configuration Setup Prompt Timeout hptio Setup Utility Uritu Boot ive 8 Exit 0f f Disabled Bulit in Number of seconds to walt for setup activation 65535 OXFFFF means indefinite Select Screen Th Select Item Enter Select Change FI General Help Fe Previous Values Optimized Defaults F4 GOVO A ESCI EXIT Use this item to set
15. al Type The optional settings are VT100 VT100 VT UTF8 ANSI Bits per second The optional settings are 9600 19200 38400 57600 115200 Data Bits The optional settings are 7 8 Parity The optional settings are None Even Odd Mark Space Stop Bits The optional settings are 1 2 Flow Control The optional settings are None Hardware RTS CTS VT UTF8 Combo Key Support The optional settings are Enabled Disabled Recorder Mode The optional settings are Enabled Disabled Resolution 100x31 The optional settings are Enabled Disabled 31 Legacy OS Redirection Resolution The optional settings are 80x24 80 25 Putty Keypad The optional settings are VT100 LINUX XTERMR6 SCO ESCN VT400 Redirection After BIOS POST The optional settings are Always Enable BootLoader Serial Port for Out of Band Management Windows Emergency Management Services EMS Console Redirection The optional settings are Enabled Disabled When set as Enabled user can make further settings in Console Redirection Settings Console Redirection Settings The settings specify how the host computer and the remote computer which the user is using will exchange data Both computers should have the same or compatible settings Press Enter to make settings for the following sub items Out of Band Mgmt Port This item may or may not show up depending on d
16. his item to get driver information and configure Realtek ethernet controller parameter gt Reltek PCle GBE Family Controller MAC XX XX XX XX XX XX Use this item to get driver information and configure Realtek ethernet controller 3 8 Chipset Menu TIR PETAT n Chipset H a 1 North Bridge Parameters South Bridge Select Screen Th Select tom Ent ri Select Change Opt F1 General Help Previous Values Optimized D faults F4 Save 8 Exit ESCE EXIT gt North Bridge Press Enter to view current using memory information and make settings for the following sub items Intel IGD Configuration IGD Turbo Enable The optional settings are Enabled Disabled Spread Spectrum Clock The optional settings are Enabled Disabled IGD Boot Type Use this item to select preference display interface used when system boot The optional settings are DVI CRT CRT HDMI DVI LVDS Active LFP The optional settings are Disabled Enabled Disable VBIOS does not enable LVDS Enable VBIOS enable LVDS driver by integrated encoder When set as Enabled user can make further settings in LVDS2 Panel LVDS Panel Type Use this item to select LVDS panel resolution The optional setting are 640 x 480 18bit Single 800 x 480 18bit Single 800x 600 18bit Single 1024 x 600 18bit Single 1024 x 768 24bit Single 1280 x 720 18bit Single 128
17. ifferent configuration Terminal Type The optional settings are VT100 VT100 VT UTF8 ANSI Bits per second The optional settings are 9600 19200 57600 115200 Flow Control The optional settings are None Hardware RTS CTS Software Xon Xoff Data Bits The default setting is 8 This item may or may not show up depending on different configuration Parity 32 The default setting is None This item may or may not show up depending on different configuration Stop Bits The default setting is 1 This item may or may not show up depending on different configuration CPU Configuration Press Enter to view current CPU configuration and make settings for the following sub items Limit CPUID Maximum The optional settings Disabled Enabled This item should be set as Disabled for Windows XP Execute Disable Bit The optional settings Disabled Enabled Hardware Prefetcher The optional settings are Disabled Enabled Use this item to turn on off the Mid Level Cache L2 streamer prefetcher Adjacent Cache Line Prefetch The optional settings are Disabled Enabled Use this item to turn on off prefetching of adjacent cache lines Intel Virtualization Technology The optional settings Enabled Disabled When set as Enabled a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology Power Technology The optional setting
18. int LED LANILED LAN2LED Pin 1 Pin2 mu PinNO Pin Define 21 LVDS CLKAP LVDS CLKAN Chapter 3 Introducing BIOS Notice The BIOS options in this manual are for reference only Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard Users are welcome to download the latest BIOS version form our official website The BIOS is a program located on a Flash Memory on the motherboard This program is a bridge between motherboard and operating system When you start the computer the BIOS program will gain control The BIOS first operates an auto diagnostic test called POST power on self test for all the necessary hardware it detects the entire hardware device and configures the parameters of the hardware synchronization Only when these tasks are completed done it gives up control of the computer to operating system OS Since the BIOS is the only channel for hardware and software to communicate it is the key factor for system stability and in ensuring that your system performance as its best 3 1 Entering Setup Power on the computer and by pressing Del immediately allows you to enter Setup If the message disappears before your respond and you still wish to enter Setup restart the system to try again by tu
19. n Configuration CPU Fan Type The optional settings are 4 Pin 3 Pin CPUFAN Smart Mode When set as Enabled the following sub items shall appear CPUFAN Full Speed Temperature Use this item to set CPUFAN full speed temperature Fan will run at full speed when above this temperature CPUFAN Full Speed Duty Use this item to set CPUFAN full speed duty Fan will run at full speed when above the pre set duty CPUFAN Idle Speed Temperature Use this item to set CPUFAN idle speed temperature Fan will run at idle speed when below this temperature CPUFAN Idle Speed Duty Use this item to set CPUFAN idle speed duty Fan will run at idle speed when below the pre set duty PC Health Status Press Enter to view current hardware health status Shutdown Temperature Configuration Use this item to select system shutdown temperature The optional settings are Disabled 70C 158F 75C 167F 80C 176F 30 85 185 Serial Port Consol Redirection Press Enter to make settings for serial port redirection settings COM 1 Console Redirection The optional settings are Enabled Disabled When set as Enabled user can make further settings in Console Redirection Settings The settings specify how the host computer and the remote computer which the user is using will exchange data Both computers should have the same or compatible settings Press Enter to make settings for the following sub items Termin
20. ot for un buffered Single Channel Full size Mini PCIE mSATA slot x1 Slot e Half size Mini PCIE slot Integrated with dual Realtek RTL8111G PCI E Gigabit LAN chips e Support Fast Ethernet LAN function of providing 10 100 1000Mbps Ethernet data transfer rate BIOS AMI64MB Flash ROM e 1 DC 9V 24V power in connector 3 USB 2 0 port 2 45 LAN port 1 DVI I port 1 USB 3 0 port Audio Line Out port x1 1 SATAII 3Gb s port Internal I O 1 SATA Power connector 1 CPU FAN header e 1 LVDS inverter LAN Chip Rear I O 1 Front panel audio header 1 SPDIF Out header 4 Serial port header 2 9 pin USB 2 0 header Expansible to 4 USB 2 0 ports 1 GPIO header 1 SM BUS header 1 PS2KBMS header 1 Front panel header 2 LAN LED activity header 1 LVDS header 1 3 Layout Diagram Rear IO Panel Diagram USB 2 0 Port RJ 45 LAN Ports DVI I Port Line Out Port way 9V 24V DC Connector USB 3 0 Port USB 2 0 Ports Internal Diagram Front Side Serial Port Header INVERTER 4 3 2 1 SATA Power Connector REEL eed Front Panel Audio Header Line Out Port ter FEP za 88858 SATA II Port GPIO Header JU USB 2 0 Header USB 3 0 Port d 1 2 Over USB 2 0 Port 3 D Half size Mini PCIE Slot DVI I Port b P h E R ES 111111111411 Front Panel Header
21. ots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon These water drops attached on PCB or the surface of the components can bring about phenomena as minor as computer instability resulted from corrosion and oxidation from components and PCB or as major as short circuit that can burn the components Suggest starting the computer until the temperature goes up The increasing temperature of the capacitor may decrease the life of computer Using the close case may decrease the life of other device because the higher temperature in the inner of the case Attention to the heat sink when you over clocking The higher temperature may decrease the life of the device and burned the capacitor iv USER S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER NO PART OF THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER S REQUIREMENT BUT WILL CHANGE CORRECT ANY TIME WITHOUT NOTICE MANUFACTURER PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND AND WILL NOT BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTIAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMANGES FOR LOSS OF PROFIT LOSS OF BUSINESS LOSS OF USE OF DATA INTERRUPTION OF BUSI
22. rning it OFF then ON or pressing the RESET button on the system case You may also restart by simultaneously pressing Ctrl lt Alt gt and Delete keys If you do not press the keys at the correct time and the system does not boot an error message will be displayed and you will again be asked to Press gt Del to enter Setup When system POST boots you may press or key to change display device Press H key to switch HDMI DVI display first Press C key to switch CRT DVI display first 3 2 BIOS Menu Screen The following diagram show a general BIOS menu screen Setup Util tu BIOS Information BIOS Vendor American Megatrends Core Verslon 5 009 Bulld Date and Tima 02 26 2014 15152140 Hed O1 2014 System Time 00 15 51 Access Level Administrator Current Setting Value Menu Items Function Keys BIOS Menu Screen Menu Bar Select Screen Select tem Enter Select Change Opt Fit General Help Previous Values F3 Optimized Defaults Savo 4 Exit 3 9 Function Keys In the above BIOS Setup main menu of you can see several options We will explain these options step by step in the following pages of this chapter but let us first see a short description of the function keys you may use here Press lt left right to select screen Press TV up down to choose in the main menu the option you want to
23. rom filesystem device Use this item to launch EFI shell application shell efi from one of the available filesystem device Reset System with TXE disable Mode Press Enter for TXE to run into the temporary disable mode Ignore if T XE Ignition
24. s Disabled Energy Efficient PPM Configuration Press Enter to make settings for PPM Configuration PPM Confiquration EIST The optional settings Enabled Disabled 33 Use this item to enable or disable Intel SpeedStep CPU C Status Report Use this item to enable or disable CPU C status report to OS The optional settings Disabled Enabled When set as Enabled the following sub items shall appear Enhanced C state Use this item to enable or disable CPU C state Max CPU C state The optional settings C7 C6 C1 SATA Configuration Press Enter to make settings for the following sub items SATA Configuration SATA Port The optional settings Disabled Enabled SATA Mode The optional settings are IDE Mode AHCI Mode SATA Speed Support The item is for user to set the maximum speed the SATA controller can support The optional settings are Gen1 Gen2 SATA ODD Port The optional settings are Port ODD Port2 ODD No ODD SATA Port1 The optional settings are Enabled Disabled mSATA The optional settings are Enabled Disabled Network Stack Configuration Press Enter to go to Network Stack screen to make further settings Network Stack The optional settings are Enabled Disabled When set as Enabled the following sub items shall appear 4 PXE Support 34 The optional settings are Disabled Enabled Use this item to enable 4
25. sed RI RS232 3 4 Closed 5 3 4 Closed 5 2 4 6 135 4 6 Closed 12V 246 135 4 6 Closed 12V 5 JP5 4 pin Header Pin9 Function Select 2 4 Closed RI RS232 6 1 246 C 2 4 Closed RI RS232 3 4 Closed 5V 3 4 Closed 5 2 4 6 135 4 6 Closed 12V 246 135 4 6 Closed 12 7 JBAT 2 pin 5 JE 1 2 Open Normal 1 2 Closed Clear CMOS CMOS Clear SEHE COPEN 1 Case open function Pin 1 2 Closed When Case open function pin short to GND the Case open function was detected When Used needs to enter BIOS and enable Case Open Detect function In this case if your case is removed next time when you restart your computer a message will be displayed on screen to inform you of this 12 9 AT MODE 2 pin Mode Function Select Pin 1 2 closed AT MODE function is enabled In this case your computer will automatically turns on after a sudden power failure when power supply resumes AT MODE 2 1 1 2 Open Normal 1 2 Closed Mode Selected JP7 1 2 Open Enable Security Measures in the Flash Descriptor Default L 1 2 Closed Disable Security Measures
Download Pdf Manuals
Related Search