First Things First... APXG-Q5420
Contents
1. Wireless DHCP Server Enabled Enable IP Address Parameters WLAN DHCP Disabled m Ethernet DHCP Enabled m WLAN Static IP Address 192 168 10 100 wi WLAN Subnet Mask 255 255 255 0 tea WLAN Gateway Address 192 168 10 1 Wea Commit Cancel Defaults Figure 2 Access Point in Bridge Mode Express Setup Curent Values Discovery OEM Device Name OEM Cfg 1 ie Radio Startup Mode On x WLAN Parameters WLAN Connection Type Access Point SSID AirbormeAP ie WLAN Secunty Type WEP 128 WEP Key 1 Wi Ethernet Parameters Ethemet Role uA e Access Point Parameters WLAN Channel 1 h Wireless DHCP Server Enabled Enable IP Address Parameters WLAN DHCP Disabled Ethernet DHCP Enabled WLAN Static IP Address 197 168 10 7100 WLAN Subnet Mask 255 255 255 0 Wa WLAN Gateway Address 192 166 10 1 i Port Settings Web Server Port a0 a Telnet Port 23 E intemal FTP Server Listen Port 21 wi Secure Shell Server SSH Port 22 hal Commit Cancel Defaults B 4 9 JJ s4g 12 272 QUATEGRHI QUICK START GUIDE APXG Q5420 Wireless Access Point B B amp B ELECTRONICS Make The Right Connections2. 4 2 100 at requires a usemane and password Warning T E Eee otis oun Laan are authentic O Manage Your Device cont If this is not the first time you have accessed the web interface it will default to the Module Status page If it is the first time the web browser will default to the Express Setup page To access the Express Setup page select the Configuration tab at the top of the page dark blue bar and then select the Express Setup link in the left hand column light blue column You are now ready to configure your device 3 Sips a Coniiguraton aj Ceniticates a Network 3 Maintenance Note None of your changes will take effect until you click the Commit button at the bottom of the page and then reboot the device If your device is connected and configured correctly you will see the following LED Status COMM Red LINK Green POST Green POWER Blue Settings for Router Mode and Bridge Mode configurations are listed on the other side of this document Document number p n 9343 APXG Q5420 2312 Figure 1 Access Point in Router Mode Express Setup Current Values Discovery OEM Device Name OEM Cfgt L Radio Startup Mode On x WLAN Parameters WLAN Connection Type Access Point W 5510 AirborneAP ta WLAN Security Type WEP 126 amp WEP Key 1 wi Ethemet Parameters Ethernet Role m e Access Point Parameters WLAN Channel 1
3. Access Point Configuration J8 s412 2 Access Point in Router Mode See Figure 1 Connected wireless devices are set up on their own network Discovery OEM Device Name Users option Radio Startup Mode On WLAN Connection Type Access Point SSID Users option WLAN Security Type Users option Ethernet Role Router WLAN Channel Users option Wireless DHCP Server Enabled Enable WLAN DHCP Client Not used ruled sine 7 for networks with DHCP servers Enable WLAN Static IP address 192 168 10 100 E ESE Denotes first IP address assigned by WLAN DHCP server WLAN Subnet Mask 255 259 299 0 WLAN Gateway Address 192 168 10 1 APXG Q5420 Wireless Access Point Fast Easy Answers Access Point in Bridge Mode See Figure 2 Connected wireless devices are connected to corporate First check step 5 network e Then use your smart Discovery OEM Device Name Users option phone to access complete Radio Startup Mode On documentation on our WLAN Connection Type Access Point ab site Si a A a S Rant V First Things First sers option the code to the right WLAN Security Type Users option Before you begin be sure you have Ethernet Role Bridge the following WLAN Channel Users option Wastes e Wireless DHCP Server Enabled Not used ireless ACCESS romi WLAN DHCP Client Not used CD with Airborne Management Center Ethernet DHCP software and use
4. NK Off POST Orange POWER Blue Connect fo the Device Run the Airborne Management Center AMC ao This was installed during the CD installation and a menu item will be found in the Airborne folder located in the programs directory of your system The application will display the following dialog Group Lopin Select Group Name manuf and enter Group Password dpac 2 The Airborne Management Center will load and discover the attached device Devices 1 ORM Cigh WI MAC OEE PAD WIP L09 24 2 100 PWRm ZIA E Note You may be required to wait up to 180 seconds before the APXG is discovered and displayed This is due to the use of the AutolP fallback function when connected directly to the APXG O Manage Your Device New devices were discovered Do you want bo manage these new devices E Hew Devices Are Factory Default LD Are these devices using Factory default settings CO TAF SL e EDO ORRA EDO OO whew DOD Right click the device s name Under Connectivity Tools choose launch Web browser for OEM Cfg1 This will open the device s browser based management window ADD 1 a m mn nanay toc Locate OEM O g1 aao FW Raves 2 128 Configzation Management Mpat Dewee Lit gt b Cispiry Current Modde Ratus for OOM Cfgl b Brk POST LED to COMCigt Username dpac Password dpac Connect to 169 254 272 100 The server 169 25
5. r manual for networks with DHCP servers Users option 2 Antennas WLAN Static IP address 192 168 10 100 Not ised in Bridge Mode BSB ELECTRONICS WLAN Subnet Mask 255 255 255 0 Not used in Bridge Mode 1 888 948 2248 Europe 353 91 792444 WLAN Gateway Address 192 168 10 1 bb el Not used in Bridge Mode www bpb elec com 707 Dayton Road PO Box 1040 Ottawa IL 61350 Phone 815 433 5100 Fax 815 433 5109 BSE ELEC TRONICS www bb elec com E mail info bb elec com Make The Right Connections Document number p n 9343 APXG Q5420 2312 2012 B amp B Electronics Manufacturing Company Fast and easy on the web WWW bb elec com a Product Overview Front View Detachable Terminal Block Port View Serial Ports oO Setup 1 Place the AirborneAP CD in the CD DVD drive of the laptop or desktop you will be using to configure the AirborneAP device Follow the on screen directions for installation 2 Use a piece of Cat5 cable to connect the Ethernet port on the APXG to a network that supports DHCP or directly to the Ethernet port on your laptop or desktop Note When connected directly to a computer Ethernet port disable all other installed Ethernet adapters wireless or wired during the configuration process O Power the APXG Q5420 Apply power to the APXG Q5420 The unit will boot and display the following LED pattern COMM Red LI
Download Pdf Manuals
Related Search