WW13014 User Manual Eng
Contents
1. The Temperature Digital Readout Screen K e This screen shows the current setting of the thermostat in default Fahrenheit degrees e This screen will turn off after 5 minutes if there is no temperature adjustments e The temperature light L indicates if the digital reading is in Fahrenheit and the temperature light M indicates the digital reading is in Celcius Oscillating Fan D e Push the button D the indicator light I will turn on the Oscillating Fan will turn on e Push button D again the Oscillating Fan will stop NOTE The fan will continue to work for several minutes when the heaters turns off This allows the infrared components inside the heater to cool down Using Remote Control See Fig 4 Below This appliance includes a remote control To operate the appliance using the remote control ensure the unit is plugged in Each remote control is shipped with a plastic tab inserted into the battery chamber to prevent damage and power loss Pls remove by pulling on the tab out of the chamber See Maintenance Section See below for directions to use the remote control FIG 4 On Off Button 0 Heater Button R e Push button Q to turn e Push button R to turn the infrared heater on heater on The indicator a i light N will indicate when the heater is on The D infrared heater will only T turn on if the temperature setting is higher than the U V room temperature Oscillating Fan X2. 2 Clean metal surfaces with a clean damp cloth making sure not to push dust or debris into any air intake or exhaust vents 3 Do not use abrasive cleaners or spray liquids on any part of the appliance 4 Periodic cleaning vacuuming of the fan heater unit is strongly recommended to ensure that no dirt or foreign objects build up Air Filter Cleaning 1 It is suggested to clean the air filter on the back on the infrared heater on a regular basis 1 or 2 times per season or more depending on the amount of dust in the air Wash in soapy water 2 See Fig 5 and 6 for the steps to clean the air filter Battery Replacement 1 For the first time use the protective plastic tab for the battery must be removed See Fig 7 below 2 For remote control battery replacement use a Lithium Cell CR2025 3V battery See Fig 7 and 8 below for the replacement steps Remove plastic tab for 1st use Battery Fig 8 Remote Control lt gt Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEAT WAVE TROUBLESHOOTING WARNING Turn off the appliance unplug and let cool for at least 15 minutes before attempting to service Only a qualified professional should attempt to service or repair the appliance IF YOU EXPERIENCE DIFFICULTIES PLEASE DO NOT RETURN THIS PRODUCT TO STORE For assistance with this appliance please call our customer service department toll free at 1 877 744 3649 or e mail us at se
3. Fan Button W e Push the button X to e This is a High and Low yy X tum the oscillating feature setting for the fan and on and push the button X the heater again to tum the oscillating feature off Celcius Fahrenheit Setting Button T e Push the button T to change the heat readout settings The indicator light L will indicate the reading is in Fahrenheit degrees and the indicator light M will indicate Celsius degrees Temperature Buttons Increase U and Decrease V e This infrared heater is equipped with a thermostat Before the Temperature buttons will function the Heater Button R must be pushed to start the heater Then press the Temperature Button U to increase the temperature Press the Temperature Button V to decrease the temperature The infrared heater will only turn on if the temperature setting is higher than the room temperature Timer S e Ifa timer is desired push this button S the indicator 0 will blink the time will show on the digital readout screen push the button U the timer hours will increase from 30 1H 2H 3H 4H 5H 6H 7H 8H 9H push the button V the timer hours will decrease from 9H 8H 7H 6H 5H 4H 3H 2H 1H 30 Oscillating Fan X e Push this button X the indicator light I will turn on the Oscillating Fan will stop NOTE Direct the remote control at the appliance from 1 to 5 meter distance for the remote control to function properly The remote co
4. discard the plastic bag 3 BE RESPONSIBLE HANDLING THE PACKING MATERIALS WARNING KEEP PLASTIC WRAPPING AWAY FROM CHILDREN 1 Before permanently placing your infrared heater plug it into a 4 Keep the original packing for future transport and or storage convenient outlet to verify that the circuit breakers 5 Keep the front of the unit through which the heat is radiated for the outlet are on nae at least 3 feet 0 9 meter away from furniture curtains and 2 The heater may emit a slight harmless odor when first used other flammable objects materials at all times This odor is normal and is caused by the initial heating of internal heater parts and will not occur again 6 Ensure there is a grounded socket nearby back of the appliance 7 The power cord must remain at the back of the appliance 3 If your electrical heater does not emit heat consult your owner s aii Mt cla Ta Sane ah aN tl sa manual for further information Caution Do not place anything on top of this heater Failure to follow this warning may result in fire burns electric shock and or serious injuries or death Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEAT WAVE IMPORTANT SAFETY INSTRUCTIONS WARNING Any use of this appliance other than that recommended by the manufacturer in this owners manual may cause fire burns electric shock and or other serious injuries or death When using electrical
5. liable for any incidental or consequential damages including loss of profits arising from the use of this product Some jurisdictions do not allow limitations on how long an implied warranty lasts or do not allow the limitation or exclusion of incidental or consequential damages so these implied warranty limitations may not apply to you This limited warranty gives you specific legal rights You may also have other rights which vary from jurisdiction to jurisdiction Repair or replacement at A G I s option of a defective product is your sole remedy under this limited warranty In no event will A G I s maximum liability exceed the purchase price of the product paid by the consumer purchaser Any legal action taken as a result of any alleged breach of this limited warranty or arising out of any use of this product must be commenced in the State of California A G I makes no other additional warranties express or implied with respect to this product or its component parts except those express limited warranties described above No dealer of this product nor any retail establishment selling this product has any authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above If replacement parts are needed or to obtain performance of any obligation under this limited warranty phone A G I s Customer Service Department toll free at 1 877 744 3649 or write to Allen Group Int l Inc Attention Customer Serv
6. appliances basic precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Read the manufacturers instructions completely before using this appliance 2 This appliance will become hot when in use To avoid burns do not let bare skin touch hot surfaces The grill at the front of this heater in particular will become hot when the heater is active Keep combustible materials such as furniture pillows bedding paper cloth curtains etc at least 3 0 9m away from the front of the appliance Keep all items away from the sides and back of the appliance and take special care not to block the air intake or exhaust vents 3 Extreme caution is necessary when the appliance is used by or near children or invalids and whenever the heater is left operating and unattended 4 Do not operate the appliance if the power cord or plug has been damaged or the heater has been damaged or malfunctioned in any way Take the appliance to an authorized service facility for examination electrical or mechanical adjustment or repair 5 Do not use outdoors 6 This heater is not intended for use in bathrooms laundry areas and similar indoor locations Never locate heater where it may fall into a bathtub or other water container 7 Do not run the power cord under carpeting Do not cover the power cord with throw rugs runners or similar floor coverings Take care to position the c
7. cuit breaker has been tripped 1 The appliance needs to be plugged in 2 Reset house circuit breaker Digital Temperature Screen is off 1 There has been no temperature adjustments for over 5 minutes 1 Push Temperature Buttons on the Control Panel or Remote Control to light up Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEAT WAVE 1 YEAR LIMITED WARRANTY Each and every product that we manufacture is tested prior to being shipped to retail stores However certain damages can sometimes occur during transportation The following non transferable limited warranty is extended only to the original consumer purchaser of this Allen Group Int l Inc A G 1 product This product is only warranted against defects in material and workmanship subject to the normal and reasonable use and correct assembly if assembled by the consumer purchaser of the product for a period of one 1 year from the date of purchase This warranty does not apply to the normal wear and tear or to any failures or operating difficulties due to accidental damage abuse misuse alteration misapplication careless handling improper installation improper maintenance or to products used commercially This warranty does not cover light bulbs The duration of all implied warranties on this particular purpose are limited to the one 1 year duration of the express warranty period specified above In no event will A G I be
8. e product if it will not fit the outlet have a proper outlet installed by a qualified electrician This product is for use on a nominal 120V circuit and has grounding plug that looks like that plug illustrated below Make sure that the product is connected to an outlet having the same configuration as the plug No adapter should be used with this product A Grounding Pin Grounded Outlet Grounded Outlet Box NOTE A 15AMP 120 Volts circuit is required Dedicated circuit is preferred but not essential in all cases a dedicated circuit will be required if after installation the circuit breaker trips or the fuse blows on a regular basis when the heater is operating Additional appliance on the same circuit may exceed the current rating of the circuit breakers WARNING 1 Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire electric shock or injury to persons 2 Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire electric shock and injury to persons Do not attempt to wire your own new outlets or circuits To reduce the risk of fire electric shock or injury to persons always use a licensed electrician SPECIFICATIONS Technical Specifications Model WW13014 Voltage 120V Frequency 60Hz Powe
9. ice Department 377 South Lemon Ave Suite A Walnut CA USA 91789 Be prepared to provide evidence of purchase date and proof of purchase model number of your A G product part number and defective part You must pay all expenses incurred in obtaining performance of any obligation under this limited warranty including transportation postage and other incidental service costs If defective part or parts are requested by Customer Service Department you must make the product available to us free and clear of all liens and other encumbrances A G I reserves the right to change prices specifications and designs and to discontinue models without notice and without incurring obligations NOTES NOTAS Call 1 877 744 3649 for assistance or email us at service phoenixinno com
10. ntrol receptor is located in the control panel Fig 1 NOTE For remote control battery replacement use Lithium Cell CR2025 3V NOTE This appliance comes equipped with an overheat protection safety device Should the appliance begin to overheat for any reason it will automatically turn all heater functions of the appliance off The appliance will have to be reset prior to continuing use To reset the overheat protection safety device turn all controls off and unplug the appliance Wait 15 minutes plug the appliance back in and turn on If the appliance continuously overheats please call our customer service department toll free at 1 877 744 3649 or email to service phoenixinno com Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEAT WAVE MAINTENANCE WARNING BEFORE CLEANING THE EXTERIOR OF THE APPLIANCE DISCONNECT THE UNIT FROM THE POWER SUPPLY AND LEAVE UNTIL COOL CAUTION DO NOT USE ABRASIVE CLEANERS ON THE GLASS PANEL DO NOT SPRAY LIQUIDS DIRECTLY ONTO ANY SURFACE OF THE UNIT WARNING AN AUTHORIZED SERVICE REPRESENTATIVE SHOULD PERFORM ANY OTHER SERVICING WARNING Before attempting to perform any maintenance on this appliance turn all controls to the OFF position and unplug Allow the appliance to be OFF for at least 15 minutes before performing any maintenance in order to allow all components to cool properly Cleaning 1 To remove dust use clean dry cloth
11. ord away from high traffic areas and such that it can not be tripped over 8 To disconnect the appliance turn all controls OFF then remove the plug from the electrical outlet Always unplug the appliance when not in use 9 Connect to properly grounded outlets only The appliance comes equipped with a 3 prong grounding plug Do not attempt to cut the grounding prong Connect to properly grounded 120V outlets only This appliance when installed must be electrically grounded in accordance with local codes or in the absence of local codes with the current Canada CSA C22 1 Canadian Electrical Code U S A ANSI NFPA NO 70 National Electrical Code 10 Do not insert or allow foreign objects to enter any ventilation or exhaust Opening as this may cause an electric shock or fire or damage the appliance 11 To prevent a possible fire do not block air intakes or exhausts in any manner Do not use on soft surfaces like a bed where openings may become blocked 12 All electrical heaters have hot and arcing or sparking parts inside Do not use in areas where gasoline paint or flammable liquids are used or stored or where the appliance will be exposed to flammable vapors 13 When transporting or storing the heater take care to keep both the unit and power cord plug dry free from excessive vibration and away from heat sources 14 Use the heater only as described in this manual Any other use not recommended by the manufactu
12. r 1500W OPERATING INSTRUCTIONS BEFORE USING THIS APPLIANCE 1 Before permanently placing your Infrared heater plug it into a convenient outlet to verify that the circuit breakers for the outlet are on 2 The information regarding this appliance can be found on the rating plate located on the back of the unit PLUGGING IN THE HEATER 1 Plug the unit into an outlet with no less than 15Amp 120V Read all instructions and warnings prior to operating the appliance Ensure that all controls are in the OFF position before plugging the appliance in to a properly grounded electrical outlet The control panel of the appliance is located See Fig 1 and Fig 2 TR Fig 1 Fig 2 L 7 amp 8 CULE AN veaa PN a When you first turn the heater on it may emit a slight but harmless odor This odor results from certain oils or greases being heated as the appliance is used for the first time This odor is perfectly safe and will stop shortly it will not reoccur after the first operation of the appliance Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEAT WAVE OPERATING INSTRUCTIONS Using the Control Panel See Fig 3 Below H I J K LMN O P Fig 3 Master Power Switch A e Push button A to turn the appliance on The fan will turn on and the indicator lights J and H will turn on to indicate the unit is on Fan But
13. rer may cause fire electric shock or injury to persons 15 Always plug heaters directly into a wall outlet receptacle Never use with an extension cord or relocatable power tap outlet power strip 16 Do not attempt to burn wood or other materials in this heater 17 This appliance comes equipped with an overheat protection safety device Should the appliance begin to overheat for any reason the thermal cutout of appliance will engage and then all functions of the appliance will shut down The appliance will have to be reset prior to continuing use To reset the overheat protection safety device turn all controls off unplug the appliance for 15 minutes Then plug the appliance back in and turn on SAVE THESE INSTRUCTIONS Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEAT WAVE GROUNDING INSTRUCTIONS This product must be grounded If it should malfunction or break down roenaing provides a path of least resistance for the electric current to reduce e risk of electric shock This product is equipped with a cord with an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances DANGER Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service technician if you provided with th
14. rvice phoenixinno com FREQUENTLY ASKED QUESTIONS FAQS 2 House circuit breaker has been tripped PROBLEM POSSIBLE CAUSE SOLUTION The appliance turns off and will not 1 The overheat protection device in the appliance 1 Turn all controls off unplug the appliance allow to cool for turn back on has been triggered 15 minutes plug back in and restart 2 Reset house circuit breaker Remote Control does not work 1 Low Batteries 2 The overheat protection device in the appliance has been triggered 1 Replace the battery in the Remote Control See Maintenance Section 2 Turn all controls off unplug the appliance allow to cool for 15 minutes plug back in and restart No warm air is coming from the heater 1 The overheat protection device in the appliance has been triggered 2 Thermostat is set lower than room temperature h Turn all controls off unplug the appliance allow to cool for 15 minutes plug back in and restart 2 Push temperature buttons on control panel or remote control to increase temperature The appliance does not turn on when the button is pushed to ON 1 The overheat protection device in the appliance has been triggered 1 Turn all controls off unplug the alliance allow to cool for 15 minutes plug back in and restart Remote Control will not turn on the appliance when the power button is pushed ON 1 The heater may be unplugged 2 House cir
15. ton B e This is a High and Low setting for the fan e The fan light area H denotes the Low fan setting and the fan light area P denotes the High setting As well the Temperature Digital Readout Screen K will indicate LO and HI Heater Button C e Push button C to turn the heater on The indicator light N will indicate when the heater is on The infrared heater will only turn on if the temperature setting is higher than the room temperature e Push button C again to turn the heater off Timer E e If the timer is desired push this button E the indicator 0 will blink The time will show on the digital readout screen push the button F the timer will increase from 30 1H 2H 3H 4H 5H 6H 7H 8H 9H push the button G the timer hours will decrease from 9H 8H 7H 6H 5H 4H 3H 2H 1H 30 Note The timer is approximate and extreme caution is necessary when the heater is left operating and unattended Keep children invalids and pets away from the unit when in use Temperature Buttons Increase F and Decrease G e This infrared heater is equipped with a thermostat Before the Temperature buttons will function the Heater Button C must be pushed to start the heater Then press the Temperature Button F to increase the temperature Press the Temperature Button G to decrease the temperature The infrared heater will only turn on if the temperature setting is higher than the room temperature
16. wo MEAT WAVE Barrington Infrared Tower Heater User Manual SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE If you are assembling this unit for someone else give this manual to him or her to read and save for future reference q Allen Group Int Inc Liste 377 South Lemon Ave Suite A Walnut CA USA L2045 C US OERE 91789 FEB 2014 Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEAT WAVE IMPORTANT SAFETY INSTRUCTIONS Quick Reference Guide an RISK OF ELECTRICAL SHOCK DO NOT OPEN EQUIPMENT PLEASE READ THESE SA 1965 NO USER SERVICEABLE PARTS INSIDE SA 1965 INSTRUCTIONS CAREFULLY oe CAUTION BEFORE OPERATING THIS READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE KEEP DRAPERY AND OTHER FURNISHINGS AT LEAST 3 FEET 9 METER FROM THE FRONT AND SIDES OF THE ELECTRICAL HEATER WARNING 1 WARNING TO REDUCE THE RISK OF FIRE KEEP COMBUSTIBLE MATERIAL SUCH AS FURNITURE PAPERS CLOTHES AND CURTAINS AT LEAST 3 FEET 0 9 M FROM THE FRONT OF THE HEATER AND AWAY FROM THE SIDES AND REAR 2 SERVICING SHOULD BE DONE ONLY WHILE THE ELECTRICAL HEATER IS DISCONNECTED FROM THE POWER SUPPLY SPECIAL CHARACTERISTICS A This heater is ideal for use all year round even when central heating has been turned off B This heater produces a hot current of air UNPACKING AND INSTALLING THE ELECTRICAL HEATER 1 Open the packaging carefully and remove the heater 2 Remove and
Download Pdf Manuals
Related Search