Infinity ACL M
Contents
1. WARNING Always make sure that both the structure and the fixing devices screws clamps etc are suitable for holding the weight of the unit The structure must also be sufficiently rigid so as not to move or shake whilst the Infinity ACL M projector moves during its operation Make sure that the supporting structure is not subject to torsion Do not install the projector in locations readily accessible by unauthorised or untrained personnel who is not aware of these safety instructions 4 2 Safety connection If the Infinity ACL M is fixed to a structure the use of a safety chain is recommended in order to meet the current relevant safety standards The safety chain must pass through the holes A and then fixed to the structure itself If using steel wires or chains which have not been manufactured by Coemar make sure that they are suitable for holding the weight of the unit 5 Powering up 5 1 Connecting to mains power Mains cable characteristics The mains cable provided is complying with the most recent standards NB In case of cable replacement similar cable with comparable thermal resistant qualities must be used exclusively cable2. English 10 5 Standard color wheel configuration CODE POS ROSCO STANDARD N VT357 1 026 Bright red 1 VT351 2 022 Dark Amber 1 FCO50 3 441 Full CT straw 1 VT359 4 UV405 1 VT353 5 079 Just blue 1 10 6 How to replace filters 1 Facing the front side of the wheel push up the filter to replace inserting your finger through the plate hole then remove the filter 2 Insert the new filter facing the coated side downwards making it slip under the spring until it locks respect the coated side of the filter bottom side NB The wheel only accepts glass filters or gobos with a maximum diameter of 40 mm and no more thick than 1 mm 10 7 Reassembly the groups on the projector In order to reassembly the two groups in place just follow backwards the procedure explained at the beginning of this chapter half insert the gobo assembly and incline it toward the front of the fixture Insert the colour changer and then full insert the gobo assembly Fix the two groups by their screws connect the cables and fix them again Verify that the internal of the body is free from loose pieces washers screws etc then fix the body cover 26 English 11 Maintenance 11 1 Periodic cleaning Lenses and filters Even a fine layer of dust can reduce the luminous output and alter the compactness of the beam Regularly clean all filters and lenses using a soft cotton cloth dampened with a specialist lens clea
3. ID CODE PROJECTOR CONTROL Default IP address It allows to configure MODE ARINEtony Custom IP address the fixture to be Gobo rotation Universe address __ controlled by ARTnet to DMX MAC address ARTnet protocol Frost filter Color wheel BALLAST SETTING Default IP address It allows to control Custom IP address the fixture setted in C AU du MAC address ARTnetcontrllr MAC address Magenta E 575 W lamp power Lamp type E 700 W lamp power Zap effect It resets the ballast s A 2 15 English The following diagram explains the sub menu for the management of pan and tilt regarding the pan tilt menu item described in the diagram at previous page Clockwise It inverts the horizontal beam direction from left to right or vice versa by the same DMX PAN TILT PAN DIRECTION Counterclockwise E y 540 Panoramic working mode that reduces rotating angle from PAN ANGLE 400 540 to 400 Clockwise It inverts the vertical moving beam direction TILT DIRECTION i from upwards to downwards or vice versa by Counterclockwise the same DMX level change ai of It allows to enable or disable the optical sensors which check the base s or the yoke s position or Panony HH og body and perform the automatic return if moved accidentally 5 Tilt only gt PAN TILT MOVEMENT ENABLE Pan Tilt It allows to engage or disengage the pan the tilt or both movements It allows to start
4. 0 0 11 132 135 0 0 11 152 0 6 15 23 31 39 46 128 191 0 0 0 0 11 31 129 250 0 11 31 10 255 255 10 131 134 255 255 10 151 255 5 14 22 30 38 45 127 190 255 255 255 255 10 30 128 249 255 10 30 249 English 0 4 4 100 0 0 4 52 53 0 0 4 60 0 2 6 9 12 15 18 50 75 0 0 0 0 4 12 51 98 0 4 12 250 255 98 Note 6 when using halogen lamp channel 18 16 bit 17 8 bit allow the selection of the curve which can be a combination of the characteristic dimming lamp and or mechanical dimmer 19 20 19 gobo effect selection step lamp on off and ste motors reset p no effect proportional movement of the gobo wheels through 360 proportional stepmovement of the gobo wheels through 360 park no function lamp off pan and tilt reset once only all motor reset exept black out pan and tilt once only all motor reset exept black out once only reset of all the motors once only LCD display off LCD display on lamp on Note 7 the display panel may be used to disable the switching off of the lamp via DMX Note 8 turning off the lamp and all reset functions are delayed by 6 seconds to prevent accidental activation Note 9 the lamp
5. 17 18 18 13 14 15 16 17 17 step color wheel selection proportiona cyan proportiona magenta proportiona yellow proportiona zap effect effect varies depending upon channel 7 step strobe halogen dimmer curve effect varies depending upon channel 6 step dimmer white beam color 1 color 2 color 3 color 4 color 5 from white to white beam color 1 2 3 4 5 proportional positions rainbow effect from fast to slow in an clockwise direction rainbow effect from slow to fast in a counter clockwise direction proportional control of the percentage of cyan color in the light beam from 0 to 100 proportional control of the percentage of magenta color in the light beam from 0 to 100 proportional control of the percentage of yellow color in the light beam from 0 to 100 no effect zap effect synchronised with the strobe effect speed and mode selected by strobe channel 7 zap effect flicker and speed adjustable speed and mode selected by strobe channel 7 proportional movement of the strobo profile black out of the light beam during PAN TILT movement gobos wheel and color wheel standard dimmer mechanical the mechanical dimmer works in sync with the dimming of the lamp the mechanical dimmer has no effect and is active only that the halogen lamp variable color temperature black out of the light beam during PAN TILT movement gobos wheel colors wheel and effects wheel 0 11
6. 3X 1 5 y external 10 mm rated voltage 300 500V test voltage 2 KV operation temperature 40 C 180 C Coemar cod CV5311 Connection to mains power For connection to mains use a connector of a suitable rating to sustain the maximum current 200 208 230 240 Vac 8 amps constant current in normal operation English Identify the mains cable which exits the base of the unit and connect as shown below brown omamne e E ih o blue blu N yellow green G N D TTT CTT lallo verde WARNING The use of a thermal magnetic circuit breaker is recommended for each projector Strictly adhere to all regulatory norms Infinity ACL M cannot be powered through Dimmer power units A good earth connection is necessary for the correct operation of the Infinity ACL M Never connect the projector to main power if the green yellow earth cable provided is not correctly connected All cable and plug connections must be carried out by qualified personnel only 6 Control signal connections The digital control signal is transmitted to the projector via a two pole cable screened as per international standards for the transmission of DMX512 data The connection must be serial utilising connectors XLR3 and XLR5 male and female located on the base of Infinity ACL M labelled DMX 512 IN and OUT see diagram Control signal connection by
7. XLR3 e XLR5 plugs Pin 1 GROUND Pin 2 DATA Pin 3 DATA Pin 4 NC Pin 5 NC When signal arrives from a DMX 512 console with Cannon XLR5 5 poles pins 4 and 5 must not be connected DMX 5121 WARNING Make sure that screening and conductors are not in contact one another or with the metal housing of the connector Pin n 1 and housing must never be connected to the unit power supply 6 1 Connection through ArtNet protocol The ArtNet protocol allows enabled projectors to operate and to be seen as a normal network device such as a standard P C connected to a company network Infinity ACL M leaves the factory ready to be connected to an ArtNet network without any further settings Just connect the projector by means of the specific RJ45 connector located on the side of the DMX connectors and the relative patch to a common HUB Ethernet which will be connected to an ArtNet controller Each Coemar projector has its own IP address therefore it is not necessary to set it when connecting it to the network Should it be necessary to modify the IP address for reasons related to the net each Coemar projector allows customization In order to modify the net setting access the MAIN FUNCTION PROJECTOR CONTROL MODE ARTNET ONLY menu alternatively Artnet to DMX CUSTOM IP ADDRE
8. connectors Press the connectors if necessary and reposition as before 11 3 Fuse replacement Check the conditions of the fuses using an appropriate instrument if damaged replace them with equivalent ones 12 Spare parts 12 1 Spare parts All the components of Infinity ACL M are available as replacement spares from your authorized Coemar service centre Accurate description of the fixture model number and type will assist us in providing for your requirements in an efficient and effective manner 27 English 13 Error messages If you have to check a malfunction Infinity ACL M has an auto diagnostic system that visualizes in the lower part of the display one or more intermittent messages preceded by ERR The following table will help you to understand these messages correctly If the problem persists despite carrying out the suggested procedure contact your Coemar Customer Service Centre Error mesage Description and suggested solution ERR Memory FAILURE Internal memory writing error Contact your authorized Coemar Service centre ERR CFG data FAILURE Configuration data error The initial parameter setting has failed the projector has loaded its factory default setting Turn the i projector off and on again Should the error reoccur refer to your authorised Coemar service centre ERR DMX address DMX addressing error The projector is not receiving all DMX channels need
9. gt gt WARNING lt lt lt Current MH lamp Current MH lamp setting is 700 W setting is 575W PLEASE CHECK PLEASE CHECK CORRECT SETTING CORRECT SETTING The system warns you that Infinity M has been set to work with 700 W The system warns you that Infinity M has been set to work with 575 W metal halide discharge lamp metal halide discharge lamp 4 Check that the setting matches the lamp you ve installed if it doesn t match turn off immediately the unit and repeat the procedure described above 5 Once made the correct setting turn on Infinity M turn on the lamp and don t forget to adjust it Dimmer mode explanation Halogen dimmer curve channel Dimmer shutter status Lamp status time see DMX chart above Minimum power 0 seconds Dimmer closed Mechanical dimmer works in sync with the off 5 minutes dimming of the lam mag p Minimum power 10 seconds Shutter closed off 5 minutes Dimmer closed off 0 seconds Mechanical dimmer has no effect and is active only that the halogen lamp variable color Minimum power 10 seconds temperature Shutter closed off 5 minutes Minimum power 10 seconds Dimmer closed Black out of the light beam during PAN TILT off 5 minutes movement gobos wheel colors wheel and effect wheel Minimum power 10 seconds Shutter closed off 5 minutes 22 English 10 Operating on inside groups The fixture allows the extraction of both gobos and colour changer assemblies i
10. movement motor check the motor and the relevant cabling ERR Encoder TILT TILT encoder not found Check the sensor of the encoder wheel placed on the fixture s yoke to detect the position of the TILT movement motor check the motor and the relevant cabling ERR Sensors Line 2 Sensor line 2 error Control circuit error relating to position sensors for the motors GOBOS posta nella forcella il sensore non rileva il magnete The sensor does not detect the magnet Check sensor and motor cabling of the Gobos assembly ERR Sensors Line 5 Sensor line 5 error Control circuit error relating to position sensors for the motors of the colour changer assembly The sensor q does not detect the magnet Check sensor and motor cabling of the colour changer assembly ERR COLOR Wheel Position error of the color wheel The sensor does not detect the magnet Check the functioning and the correct positioning of the magnetic sensor of the colour wheel Check the correct tightening of the transmission belt ERR GOBO Wheel Position error of the gobo wheel The sensor does not detect the magnet Check the functioning and the correct positioning i of the magnetic sensor of the gobos wheel ERR GOBO Index Initial position error in the gobos wheel The sensor does not detect the magnet Check the functioning and the correct positioning of the magnetic sensor placed on gobos 1 28 14 Frequently asked questions English Question Possible c
11. setup brightness functions of the fixture pan tilt management lamp management fans management reset motors test ID code backlight shutdown time back to original settings and access to buttons shutdown time DISPLAY MAIN SPECIAL MODE 180 reading of the display SETUP FUNCTIONS positive or negative graphic MEASURES allows the reading of all MEASURES DEMO allows the performing of the functional settings of the fixture demonstration program 4 different demo temperatures fans power DMX channels programs are available values diagnostics lamp status and life and diagnostic version of the installed software 8 2 Rapid count By the display panel of Infinity ACL M It is possible to rapidly change the various numbers displayed for the different functions in the following 3 manners 1 Pressing the or buttons will cause the count to be quicker 2 Pressing first and then and then holding them down simultaneously will cause the numbers to jump to the highest value 3 Pressing first and then and then holding them down simultaneously will cause the numbers to jump to the lowest value 14 English 8 3 Main functions The projector gives the opportunity to change and customize some functional settings MAIN FUNCTIONS See diagramin It allows the complete management of the horizontal and vertical at next page PAN TILT dd movements CMY SETTING aa It allows to choose an
12. 0V TAL halogen Coemar code 105830 105831 BC10013B001 Power range 700 W full power 400W low power 575 W full power 400 W low power 750W Lighting flow 50000 Im 35600 Im 21500Im Color temp 7200 K 7400 K 3200 K Base PGJX28 Life 750 h 200 h WARNING Balast setting and lamp replacement must be done by qualified personnel Disconnect the unit from main power prior to attempting lamp s installation or replacement The fixture internal temperature can reach 250 C after 5 minutes and reach a peak of 350 C make sure that the lamp is cold before trying to remove it In any case the fixture can be opened only 10 minutes after turning off the lamp The lamp is of the mercury vapour type with discharge ignition This type of lamp operates at high internal pressure and a slight risk of explosion exists if the lamp is operated beyond its recommended life Therefore we recommend to replace the lamp within the specified lamp life Always handle the lamp with care avoiding to touch it with bare hands 9 1 Lamp installation 1 Use a suitable tool to loosen the 2 fixing screws A of the lamp holder cover at the rear of the projector body 2 Remove the lamp holder cover B 3 Insert the lamp into the holder and gently rotate it clockwise until it blocks 4 Una volta in sede ruotate la lampada in senso orario fino a bloccarla The lamp used is made of quartz glass and must be handled with care always adhere to the instructions pr
13. 31 from your DMX 512 controller A second unit must be addressed as A032 a third as A063 and so on The operation must be carried out every Infinity ACL M which has an address different from A001 Altering DMX address 1 Press the or button until the display shows the required DMX address The digits on the display will blink to indicate that the variation has not been registered 2 Press the enter key to confirm your selection The digits on the display panel will cease to blink and the projector will now respond to the new address DMX ADDRESS A001 ot ne o te O 33 u NB by holding the or button down the scrolling will be faster thus allowing a faster selection WARNING If you alter the DMX address with no DMX signal connected the digits on the display panel will continue to flash even after you have pressed ENTER button to confirm the address 11 English 7 2 DMX functions Note the default setting is 16 bit 24 channels effect proportional coarse control of the base motor movement proportional fine control of the base motor movement proportional coarse control of the yoke motor movement proportional fine control of the yoke motor movement standard fast ultra fast movement best for programming positions vector mode from fast to slow tracking mode from fast to slow smooth mode gradual adjustment of luminous intensity from 0 to 100 see channel 18 17 shutter clo
14. 66 167 192 193 255 0 10 11 192 193 255 percentag e 0 100 0 100 0 100 0 0 4 10 50 97 0 0 4 26 27 49 50 73 74 96 0 4 26 74 96 0 4 0 4 49 51 75 76 0 4 15 25 35 45 55 65 76 0 4 100 4 10 50 97 100 100 4 26 27 49 50 72 73 96 100 4 26 73 96 100 4 100 4 49 51 74 75 100 4 14 24 35 45 55 65 75 100 4 75 76 100 10 11 12 10 11 ste indexing gobo rotation through 360 e proportiona fine indexing of the gobos 16 bit proportiona step proportiona gobo rotation step proportiona no effect proportional indexing of the gobos through 360 fine indexing of the gobo no effect continuous rotation of the gobo in a clockwise direction with proportional control over decreasing speed gobo stop continuous rotation of the gobo in a counter clockwise direction with proportional control over increasing speed Note 4 when channel 10 is set to a level between 0 and 10 gobo rotation does not effect indexing the gobo stops instantly 13 13 12 12 frost proportiona frost step gradual adjustment of frost filter from 0 to 100 no effect frost selection 1st level frost selection 2nd level Note 5 frost channel will vary according to the selection made from display function 14 15 16
15. Gobo position alignment GOBO ROTATION Cyan filter alignment CYAN x i Magenta filter alignment MAGENTA Yellow filter alignment YELLOW It stores the settings and closes the procedure EXIT SPECIAL FUNCTIONS It restores to 0 the resettabile lamp s electronic LAMP HOURS RESET lt lt Are you sure gt gt odometer visible also in MEASURES menu It must be restored each time the lamp being changed in order to get a correct reading of lamp s life DOWNLOAD It makes the fixture ready to transfer the LCD lt lt Are you sure gt gt software on to the PC LCD MASTER y DOWNLOAD It make the fixture ready to transfer the MOTORS lt lt Are you sure gt gt software on to the PC MOT SLAVE y ti UPLOAD It makes the fixture ready to receive the LCD lt lt Are vou sure gt gt software from the PC LCD MASTER y gt UPLOAD It makes the fixture ready to receive the MOTORS lt lt Are you sure gt gt software from the PC MOT SLAVE y di 19 English 9 Lamp installation and alignment Infinity M utilizes a Philips MSR GOLD 700 2 Mini Fast Fit with PGJX28 base lamp at maximum power of 700 W or a Philips MSR GOLD 575 2 Mini Fast Fit with adequate ballast setting men MAIN FUNCTIONS BALLAST SETTINGS These lamps are available as a spare part at your Coemar s distributor or service centre Lamp Philips MSR Gold 700 2 Mini Fast Fit Philips MSR Gold 575 2 Mini Fast Fit Q750W 10
16. SS see complete menu art 8 3 10 English 7 Turning on the projector After having followed the preceding steps proceed with the power supply and turn on the projector via the main power switch The display will show a short welcome message and the software version installed on the internal microprocessors INFINITY ACLM SW LCD ver XXX SW MOTORS ver XXX The projector will perform the reset function on all motors This operation will last a few seconds thus allowing the digital control motors to correctly position themselves Then the display will turn on in a fixed mode indicating the correct DMX 512 signal reception DMX ADDRESS PLEASE WAIT During the reset function the display will blink for a few seconds then the DMX address of the projector will appear If the address continues to blink and the NO DMX SIGNAL message appears it means that the DMX signal has not been received Check the connection cable and the mixer functioning 7 1 DMX address of the projector NB The following section is valid only in the case where Infinity Spot XL is controlled by the signal DMX 512 Each projector utilises 31 address channels 16 bit for its complete operation and is controlled by a DMX 512 signal for further information see section 7 2 DMX functions When powered up initially each projector will show A001 which indicates DMX address 001 a projector thus addressed will respond to commands of channel 1 to
17. aio ene i ne ee ee aa 23 10 1 How to open the projector cnn rc RR RR RARE RARE Ren nn nan nn nana 23 10 2 How to extract the gobos and colour changer assembly i 23 10 3 Standard gobos wheel configuration gobos wheel 1 10 4 li od O O NN 10 5 Standard color wheel ci a aaa 26 10 6 How to replace filtersiic racer A a A eden sees hie Aenea Wee a ied ea Ace eee arate 26 10 7 Reassembly ithe groups on the projectori 1us4 cae sa a 26 Ti Maintenance oi A ee al Aia 27 od POMOGICCICAMING A AO NANA 11 2 Periodic maintenance A AAA NN 12 Spareparts A een A alan 27 12 1 Spare MS A A A A A A AAA AA AA eee 27 13 Err messages it AA A A AAA A a ee 28 14 Frequently asked questions nono Ta a ap arra aa AET a a adaa RRE 29 English Sanat on having purchased a Coemar product You have assured yourself of a fixture of the highest quality both in the componentry and in the technology used We renew our invitation to you to complete the service information form on the previous page This will assist in providing prompt and accurate advice from your Coemar service centre which you can thoroughly trust and to which you can submit any requests for service or information Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for years to come 1 Packaging and transportation 1 1 Packaging Open the packagi
18. alternative colour insertion curve Special Tungsten It allows to simulate dimming feat fat X 3 DIMMER SETTING imming features of a Tungsten lamp or a Xenon lamp Gobos 8bit It allows to choose the gobo s working resolution please see GOBOS resolution 16bit DMX chart Linear Enables or disables the pulse effect of the iris please see DMX chart IRIS Pulse FROST MODE CONTROL Proportional It allows to choose the insertion mode of the frost filter please see DMX Step chart Normal NORMAL fans are controleld by pcb in function of the internal temperature FANS MODE CONTROL High HIGH fans are always set at full power On STANDARD the on off state of the lamp s controller by DMX signal LAMP STRIKE DMX Standard ON the lamp remains always on please see DMX chart All It perform the reset function of the fixture RESET Pan Tilt onl Keeping pressed ENTER and MENU buttons during reset It all Effect Only itwill access SPECIAL MODE see special mode menu n motor without using DMX signal SAVE Restores all the functional settings excepts for ALL allows to store RECALL DEFAULT lt lt Are you sure gt gt address motors tuning and odometers to default the motors position SETTING values until next fixture s start up On Enables or disables the lamp s zap effect Lets you set the ID code of the fixture by using or buttons Shutter DMX only Gobo wheel
19. ase casing Base Camlock plate FI IJO 1 mM oO oO w D gt 4 Installation 4 1 Mechanical installation Infinity ACL M may be either floor or ceiling mounted It may also be installed on a structure The unit is provided with four rubber feet mounted on its base allowing it to be placed on a flat surface For installations on a reticular structure Coemar provides a set of Cam lock support brackets which are included in the packaging The Cam lock bracket is one fourth turn supports Before using it for supporting the projector make sure that it is correctly seated and firmly tightened into position 126 3 126 3 p 89r 4 97 d _ d Ol I ar 28 me LI A ES A t O t Oo As 23 FRONT FRONT Ne L a 6 TT O 013 mm e2 09 o o o o o English For installations on a reticular structure we recommend using specific C hooks suitable for supporting the weight Normally the C hooks are tightened in the central hole of the cam lock brackets as shown in the picture below L T lt a
20. ause Suggested solution The projector is completely still The projector resets correctly but either does not respond or responds incorerctly to DMX signal The lamp functions intermittently or does not turn on at all Projector not powered up The circuit breaker is switched off The protection fuse is blown Incorrect signal connection Incorrect DMX address The projector is too hot Check that the mains power cable is connected to power Set the circuit breaker to ON Disconnect the projector and replace the fuse Inspect the signal cable rectify any incorrect wiring repair or replace any damaged cables or connectors Check the DMX address Let the fixture cool down Check that the air vents above the cooling fans are not obstructed and that the fans are working correctly Ensure that the ambient temperature is below 35 C Projection brightness appears reduced Lamp may be exhausted or not properly aligned to optical path Replace the lamp if exhausted Align the lamp to optical path Information on disposal of the equipment The equipment at the end of its useful life must be disposed of at an appropriate recycling center for waste electrical and electronic equipment The treatment and disposal of environmentally friendly helps prevent potential negative environmental and health and promote the reuse and or recycling of materials making up the equipment Illegal dispo
21. ed to operate correctly Check the DMX address a indicated on the display and the number of channels being output from the controller some controllers do not exceed 12 channels ERR DMX frame DMX frame error DMX signal present but frame too short the controller has not enough channels to control the projector ERR No Slave LINK Communication error The LCD board is not communicating properly with the main board Check the cabling connecting the i boards or refer to your authorised Coemar service centre ERR No Ballast LINK Communication error The LCD board is not communicating properly with the ballast Check the cabling connecting the x boards or refer to your authorised Coemar service centre ERR Ballast Temp 1 Primary ballast temperature too high Check that the ambient temperature does not exceed 40 C check also the proper i i functioning of the fans ERR Ballast Temp 2 Secondary ballast temperature too high Check that the ambient temperature does not exceed 40 C check also the proper functioning of the fans ERR Vinp line low Too low main power input Main power voltage is too low it must be at least 90 Vac ERR Vout lamp high Too high lamp voltage Lamp can be exhausted and so consume more power than normal Replace the lamp and if needed i refer to your authorised Coemar service centre ERR Encoder PAN PAN encoder not found Check the sensor on the encoder wheel placed at the base to detect the position of the PAN
22. he ballast NStsk lamp s strike attempts with countdown 8 5 Display setup The display setup allows tot une the Infinity ACL M functions according to your needs The following diagram shows the section features DISPLAY SETUP Standard It allows 180 rotation of the display graphics in case of DISPLAY REVERSE Reverse upside down installation of the fixture It allows visualization in negative or in positive of the display BACKGROUND Standard graphics COLOR Reverse OFF It allows one to decide number of seconds before turning off DISPLAY TIME OUT the display back light in case of inactivity OFF value leaves secs the backliaht alwavs on OFF It allows setting up number of seconds buttons must be pressed in order to activate functions This function avoid BUTTON TIME OUT secs activation of features if buttons are pressed accidentally It allows setting of brightness of display back light BRIGHTNESS 1 100 English 8 6 Demo mode Demo mode allows the fixture to perform up to 4 different demonstration programs Infinity ACL M It performs a demonstrative program with all systems active It performs a demonstrative program without pan and tilt movements It performs a demonstrative program using only colour changer It performs a demonstrative program including only effects features 8 7 Special mode and electronic motor alignment WARNING T
23. his section is for the exclusive use of qualified and experienced personnel SPECIAL MODE menu allows access to the electronic motor alignment section and to special functions like lamp odometer reset software upload and download To enter SPECIAL MODE reach the reset page in the MAIN FUNCTIONS menu start reset choosing ALL and press simultaneously enter and menu buttons for about 10 seconds WARNING The electronic tuning procedure is only possible when the DMX512 signal is on The display panel of Infinity ACL M allows the electronic motor alignment of the projector motors in the optical system this procedure is performed by Coemar at the factory during the testing in order to obtain particular effects or in the case of internal components being replaced motors electronic boards sensors etc it may be necessary to change this setting Altering the default settings performed by Coemar may radically alter the functioning of the projector Carefully read all of the following functions before trying to perform any operations Note pressing the buttons and simultaneously the setting returns to 128 default value 18 English WARNING SPECIAL MODE This mode is activable only by pressing for about 10 seconds both ENTER and MENU keys after the reset has been launched The DMX signal must be present MOTOR ADJUSTMENT Pan movement alignment PAN Dimmer alignment Shutter alignment Iris alignment
24. ions 3 2 2 54 oc vesen A AA ae E ets 7 3 1 Technical characteristieS s ssaa cay voces AAA IA DRAE ADA A AAA ii 7 3 2 DIMENSIONS enir ae ra aae eae aea ca 7 3 3 Projector COMPONEN iia AAA eet eee Ai e 8 4 installation RA AAA a a bd deed A ee a OE ee Te 8 4 1 Mechanicali installation iena A coves sans Rat 8 4 2 Safety connectioni AN 9 APO MN Un NI 9 51 Connecting O MA S powell ica eet es ete eee eet 9 6 Control signal connections 6 1 Connection through ArtNet protocol ttt kutt tat kAAtEAtEANEANEANEANEENNEANEANEAAEEANEANEEAENAEENEENAEAAEENNEEAEENNEAAEAEENAEENNEAEENE EEEE EEEE 10 7 TUNING ON the projecto iii AA DSi 11 7T DMX address ofthe projectoren ii A aia ania A a ia a A RATAR ATN 11 72DMX fUNCHIONS ii AA as 12 8 Display panel functions a dica 14 BA QUICKQUAS O MU Rini aden sath Ai ian 14 8 2 Rapid count 8 3 Main TNnCtlOnS it AAA AA AAA A ie ea nat aid evi ati 15 O MCASUICS eee NRO 17 8 5 Display Setup oi A bree een ae 17 8 6 DEMO mode E A ee ee ed eee es 18 8 7 Special mode and electronic motor alignment iiiir aaa aa aa 18 9 Lamp installation and alignment iaia iaia ale aa ein 9 1 Lamp installation 9 2 Aligning the lamp in the optical path a israel iaia Ria sea ani nee etek 9 3 Halogen lamp operations sanare electa 21 9 4 Turning back to discharge lamp 700W or 575W io 22 10 Operating on inside groups
25. ity M remember that in the case you are using a laptop PC you should drive USB patch trough a self powered USB Hub you are ready to perform the software installation on Infinity M that can vary regarding the two cases mentioned in the previous chapter Case A You ll have to replace the ballast with KIT BC10013B002 this one will come with the correct hardware and software version 3 70 then you ll have to upgrade LCD and MOTORS software to LCD 2 13 and MOTORS 2 09 These software versions are available in the CD included in this kit Refer to DR1 user manual to learn how to perform the software upgrade Case B You ll have to upgrade the ballast software to 3 70 This operation is slightly different respect LCD and MOTOR software upgrade 1 Go with the mouse on the fixture you have to upgrade in the left column of DR1 Lite Interface 2 Keep pressed ALT CTRL SHIFT and click the right button of the mouse a pop up menu will appear 3 Keeping pressed ALT CTRL SHIFT Click on SEND COMMAND SERVICE MENU SHOW BALLAST In the list you should now see the ballast device you are going to upload the software on 4 Upgrade the software you ll find the 3 70 file in the CD ROM included in the same way you did for LCD or MOT 5 In order to return to fixtures list repeat the operation in step 3 clicking HIDE BALLAST instead of SHOW BALLAST 6 Check that software versions are updated LCD at 2 12 and MOT 2 09 21 English WARNING af
26. made for channel 18 16 bit 17 8 bit iris diaphragm step 8 8 i LIN Linear proportional step proportional 8 8 iris diaphragm step with intemal PULS effect proportional step proportional pulse and flash effect with proportional increase in speed Note 2 the iris diaphragm operation will vary according to the selection made for IRIS on the display panel linear LIN or with intemal PULS effect 9 9 aerial gobo selection step standard proportional step 9 9 aerial gobo selection effect activated from channel 19 18 proportional no gobo gobo 1 gobo 2 gobo 3 gobo 4 gobo 5 gobo 6 gobo 7 continuous rotation of the gobo wheel from slow to fast no gobo from gobo 1 to gobo 7 through 360 gobo 1 central value 33 gobo 2 central value 55 gobo 3 central value 78 gobo 4 central value 101 gobo 5 central value 124 gobo 6 central value 147 gobo 7 central value 169 continuous rotation of the gobo wheel from slow to fast Note 3 channel 9 will vary according to the selection made for channel 19 16 bit 18 8 bit 12 decimal 0 255 0 255 0 255 0 255 0 10 11 25 26 127 128 247 248 255 0 255 0 9 10 66 67 68 69 125 126 127 128 184 185 187 188 244 245 255 0 9 10 66 67 187 188 244 245 255 0 9 10 255 0 9 10 124 125 129 130 189 190 192 193 255 0 10 11 36 37 62 63 88 89 114 115 140 141 1
27. mp was turned off 4 Always replace the lamp if any physical damage is evident 5 Never install the fixture in an enclosed area lacking sufficient air flow the room temperature must not exceed 35 C 6 Wait at least 10 minutes after the unit has been turned off before attempting to replace or remove the lamp Always use protection gloves while replacing the lamp 7 The projector contains electronic and electrical components which must under no circumstances be in contact with water oil or any other liquid Failure to do so will compromise the proper functioning of the projector Projector movement The projector has a pan range of 540 in its base and a tilt range 262 in its yoke do not obstruct the projector whilst it is moving Forced ventilation On the body of the projector you will note several air vents housing several cooling fans both in the basis and in the body To avoid any problems associated with overheating never obstruct any of these vents as this would seriously compromise the proper operation of the unit English Protection rating against penetration by external agents The fixture is classified as an ordinary apparatus its protection grade against penetration by external agents solid or liquid is IP20 2 2 Warranty conditions 1 The fixture is guaranteed for a period of 12 months from the date of purchase against manufacturing or materials defects 2 The warranty does not extend to damage caused by inapprop
28. n order to facilitate inspection gobos replacing and clearing of colour filters and lenses WARNING The following procedures should be undertaken by qualified and experienced technical personnel Handle with extreme care Always disconnect al cables before proceeding and ensure that the unit is sufficiently cool 10 1 How to open the projector Using an appropriate screwdriver remove screws A from the upper housing and remove this In order to identify the upper housing to be removed position the unit so that the printing on the lamp holder group can be read the printing must not upside down Once this operation has been carried out block the movement of the body through the specific device and proceed with the removal of the upper housing LE 10 2 How to extract the gobos and colour changer assembly 1 Remove B screws of the connectors labeled gobos and color changer and gently remove the C connector 2 Remove D screws of the two assembly manually shift forward the zooms lenses 3 Gently extract a few centimeters the gobos assembly tilt it forward 4 Now gently extract the colour changer assembly 5 Finally extract the gobos assembly partially extracted in the step above 1 7 A 2 gt N Wo I y y E 23 English 10 3 Standard gobos wheel configuration gobos wheel 1 Magnet home position Posizione iniziale del magnete Dots are reference points fo
29. ng and make sure that no part of the equipment has suffered any damage during the transportation In case of damage to the fixture contact your currier and your supplier immediately by telephone fax or email and inform them you will formally notify them in writing through registered letter Packing List Make sure the packaging contains 1 the Infinity ACL M projector 2 the instruction manual 3 the Cam Lock support brackets 1 2 Trasportation The Infinity ACL M must be transported exclusively in its original packaging or in an appropriate flight case 2 General information 2 1 Important safety information Fire prevention 1 Infinity ACL M utilizes a Philips MSR 700 Gold Mini Fast Fit or a Philips MSR Gold 575 MiniFast Fit lamp the use of any alternative lamp might be risky and will make the warranty of the fixture null and void 2 Never locate the fixture on any flammable surface 3 Minimum distance from flammable materials 0 5m 4 Minimum distance from the closest illuminable surface 0 5m 5 Replace any blown or damaged fuses only with identical ones both in size and value Refer to the connection diagram if there is any doubt 6 Connect the projector to mains power protected by a thermal magnetic circuit breaker Preventing electric shock 1 Presence of high voltage inside of the fixture Insulate the projector from mains supply before opening or performing any function which involves touching the inside of the fixture incl
30. ning solution WARNING Infinity ACL M is provided with a special Fresnel lens which is very fragile in order to guarantee it s maximum working efficiency for a long lasting time we recommend to never touch with bare hands or other tools that can scratch it avoid to hurt it or make pressure on it If cleaning is needed never use brushes paper dry cloths but use compressed air to blow dust away Fans and air passages The fans and air passages must be cleaned approximately every 8 weeks the length of the period between each cleaning will depend of course upon the conditions in which the projector is operating Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor If necessary do not hesitate to carry this out even after a shorter period of time 11 2 Periodic maintenance Lamp Check the lamp and replace it if there is any observable damage or deformation or if or if the time limit is close check the resettable counter Mechanical parts Periodically check the movement of all mechanical devices and check driving belts gears and lens guides Replace them if necessary Make sure the projector is not mechanically damaged If necessary replace the worn parts Check the tension of the belts and adjust them if necessary Electrical components Check all electrical connections in particular for correct earthing and correct attachment of all extractable
31. on off function can only be effected if an opposite level is set Projector Infinity ACL M Table number 294 Edition 2 Table name DMX 512 functions 12 Date 20 06 2011 0 11 134 0 11 30 66 101 136 171 186 200 10 133 255 10 29 65 100 135 170 185 199 255 0 4 53 0 4 12 26 40 53 67 73 78 100 4 51 53 100 100 4 59 100 2 5 9 12 15 18 50 75 100 100 100 100 4 12 50 98 100 4 12 98 100 4 52 100 4 11 25 39 53 67 73 78 100 English 8 Display panel functions By suitably using all the functions of Infinity ACL M which can be activated through its display panel it is possible to change some of the parameters and to add some functions Changing the preset settings made by Coemar can vary the functions of the projector so that it will respond differently to the controller therefore carefully read about the functions described hereunder before carrying out any possible selection 8 1 Quick guide to menu In order to access the functions just press the menu button the screen you see hereunder divided into four sections will appear the sections will be shown cyclically one by one every time the or button is pressed To select the desired function press enter DISPLAY SETUP allows the management of MAIN FUNCTIONS groups the main
32. ovided in the lamp packaging Never touch the glass directly use the polythene wrapping provided in the lamp packaging DO NOT USE UNDUE FORCE ON THE GLASS 5 Insert the lamp holder cover in its original position and screw the 2 screws A back in WARNING Never use undue force if the procedure becomes difficult Never put pressure on the glass of the lamp Never touch the glass of the lamp with bare hands WARNING Each time you replace the lamp we recommend the following operations e realign the lamp in the optical system in order to avoid dichroic filters overheating and consequent effects reset the lamp odometer to obtain reliable information about the residual life of the lamp 20 English 9 2 Aligning the lamp in the optical path Aligning the lamp in the optical system is achieved via the 3 adjusters at the rear of the projector This procedure should be undertaken to maximize output to avoid the possible overheating of the internal components due to the incorrect focusing of the beam onto components not predisposed to high temperature It is extremely important to obtain a uniform distribution of light on all beams Alignment procedure Alignment is carried out by using the 3 screws A B and C showed in the picture below The lamp should be on black out and dimmer fully open and no colours selected If the lamp is not correctly aligned a hot spot to the most central part of the beam po
33. r gobos alignment Punti di riferimento per l allinamento dei gobos 2 6 CODE POS DESCRIPTION gt JN GO80 1 Bars 7 Gost 2 Blades gt Ji GO82 3 Triangle 1 SI GO83 4 Bold Line 1 i GO84 5 Multiflower 1 i GO85 6 Two dots 1 GO86 7 Starry breakup 1 Gobos specifications Metal gobos Glass gobos undefined Glass gobos defined Working area o mm Up to 21 Up to 27 Up to 21 Diametro utile mm Fino a 21 Fino a 27 Fino a 21 Thickness mm 0 5 mm From 1 to 4 From 1 to 4 Spessore mm Da1a4 Da1a4 Overall mm Up to 27 Up to 26 8 Up to 26 8 Diametro totale mm Fino a 27 Fino a 26 8 Fino a 26 8 In case of replacing of metal gobos we strongly recommend to use special gobos provided by Coemar In any case gobo s thickness must never be below 0 5 mm 10 4 How to replace gobos 1 Lift and gently extract from the gobo wheel the support which contains the gobo you are going to replace 2 Remove the spring that fixes the gobo to the support 3 Remove the old gobo 4 Insert the new gobo respecting the black side Avoid to touch the uncoated side 5 On the gear there is an etched reference point use it to orient the gobo and fix on to the projector 6 Mount the spring ensuring it keeps the gobo firm 7 Check the gobo freely rotate and mount the gobos assembly in the fixture following backwards the procedure explained in the previous section 24 English
34. riate usage use by inexperienced operators or inadequate maintenance 3 The warranty is immediately void if the projector has been tampered or opened by unauthorised personnel 4 The warranty does not extend to fixture replacement 5 Both the serial number and the model of the projector are required for any advice or service from your authorised service centre 2 3 EC Norms The projector meets all fundamental applicable EC requirements 3 Product specifications 3 1 Technical characteristics 700 W 575 W Power 90 260 Vac 50 60Hz Autosensing Maximum current 45A 4A Power factor Cos 0 9 Lamp Wattage 700 W 575 W Maximum room temperature 35 C 95 F Weight 25 Kg 55 lbs IP rating IP20 3 2 Dimensions 408mm 16 67 gt 183mm 219 9mm w 207 18 66 FA En 3 se a e za So cut jy Uo TTT i MA ES Y 365 5mm PE L 14 827 RI a E 130 English 3 3 Projector Components Components description Front lens assembly Body Gobos assembly Body casing Colour changer assembly Lamp assembly Yoke B
35. sal by the user includes the application of administrative sanctions provided by law 29 CE Coemar s p a via Inghilterra 2 A 46042 Castel Goffredo Mantova Italy ph 39 0376 77521 fax 39 0376 780657 info coemar com Coemar si riserva il diritto di apportare modifiche senza preavviso Coemar reserves the right to effect modifications without notification
36. sed zap off strobe effect with variable speed from slow to fast shutter open zap off sequenced pulse effect slow closing fast opening with variable speed from slow to fast shutter open zap off sequenced pulse effect fast closing slow opening with variable speed from fast to slow shutter open zap off random strobe effect non synchronised variable speed from slow to fast shutter open zap off shutter closed zap off strobe effect with variable speed from slow to fast proportional control of the shutter profile from open to closed random strobe effect non synchronised variable speed from slow to fast shutter open zap off open from maximum to minimum aperture open from maximum to minimum aperture minimum diameter pulsing with proportional increase in speed open channel 16 function type of 8 bit control bit X axis base movement 1 1 proportional pan coarse X axis base movement 2 2 proportional pan fine Y axis yoke movement i 3 3 tilt coarse proportional Y axis yoke movement 4 4 tilt fine proportional step step 5 5 movement speed proportional proportional step 6 6 dimmer proportional step proportional step proportional 7 7 strobe shutter n and zap effect sep proportional step proportional step step proportional 7 7 strobe shutter profile proportional proportional step Note 1 channel 7 will vary according to the selection
37. ssible and then flatten the beam to maximum uniformity The combined regulation of the three adjusters allows horizontal vertical and axial regulation of the lamp Adjust lamp position by turning screws A Band WARMING Case extremely hot tuno MBR Goki 700 2 MR GOKI 575 2 Mini Fast FA base PGIXZ0 4 f D O toosen y torclamp Y 9 3 Halogen lamp operations Previous to install the lamp you should ensure that your Infinity M has the software required to manage the new features Keep pressed while turning on the unit and keys the display shows a screen like this Version configuration Situation Action INFINITY _M sii b SW LCD 2 10 00 ai snot Replace the ballast with kit A SW MOTORS 2 04 00 AA BC10013B002 and upgrade LDR LCD 1 40 suitable SW ballast version must LDR MOTORS be successive to 1 70 SW BALLAST 1 70 LCD and MOT software INFINITY M SW LCD 2 12 00 The ballast is suitable for the B SW MOTORS 2 08 00 halogen lamp but it is Update ballast software using LDR LCD 1 40 recommendable update the ballast DR1 LDR MOTORS 2 40 software to version 3 70 SW BALLAST 1 80 In order to upgrade the software on your Infinity M DR1 device is strictly required Provide yourself with this product if you do not have it After you have installed DR1 Lite Interface on your PC and you have correctly connected PC DR1 device to Infin
38. ter the installation of this lamp and each time you replace it we recommend the following operations realign the lamp in the optical system in order to avoid dichroic filters overheating and consequent effects reset the lamp odometer to obtain reliable information about the residual life of the lamp 9 4 Turning back to discharge lamp 700W or 575W This is a very important chapter if you are going to replace the halogen lamp for the 700W OEM configuration or 575 W lamp Please read it carefully and ensure you have understood the topics The transition from discharge lamp 700 or 575W to halogen lamp requires no settings in fact the equipment recognizes the type of lamp and set automatically The reverse operation halogen to 700 575W requires that the projector s setting matches the type of lamp we are going to install for example if your Infinity M was set to work with 700W lamp before the transition to halogen you are going to install a 575W lamp and you forget to set Infinity M when you ll turn the lamp on the projector will be damaged Follow these hints to change the lamp safely 1 Install the discharge lamp 2 Turn on Infinity M keeping pressed MENU ENTER e and follow the instruction to change the lamp setting 3 Turn on again the projector and look at the display Infinity M will delay the turning on of the lamp to give you the opportunity to check the type of lamp set gt gt gt WARNING lt lt lt gt
39. ty ACL M CO Inf instruction manual manuale di istruzioni Version 2 1 DIS127 OOInfinity ACL M Serial number numero di serie Date of purchase data di acquisto Retailer fornitore Address indirizzo Suburb cap citta Capital city provincial State stato Tel fax Please note in the space provided above the relative service information of the model and the retailer from whom you purchased your Infinity ACL M this information will assist us in providing spare parts repairs or in answering any technical enquiries with the utmost speed and accuracy Prendete nota nello spazio apposite dei dati relative al modello e al rivenditore del vostro Infinity ACL M questi dati ci permetteranno di assistervi con la massima rapidita e precisione WARNING the security of the fixture is granted only if these instructions are strictly followed therefore it is absolutely necessary to keep this manual ATTENZIONE la sicurezza dell apparecchio garantita solo con l uso appropriato delle presenti istruzioni pertanto necessario conservarle User Manual Version 2 1 edition March 2012 English Index 1 Packaging and TAN SPOTAION viii Ate ee A ee eee ee ea 6 TA PACKAGING hosi insasi iaei a neni aaa iaia 6 AA A NN O 6 2 General informati n eisean a i i a E N E pe i ee 6 2 1 Important Safety information init A rede io 6 22 Warranty Conditions occasion anil 7 AAN A A O A i di le il a e nai 7 3 Product specificat
40. uding lamp replacement 2 For the connection to the mains adhere strictly to the guidelines outlined in this manual 3 The level of technology of Infinity ACL M requires the use of specialised personnel for all service applications refer all work to your authorised Coemar service centre 4 A good earth connection is essential for the proper functioning of the projector Never connect the fixture if there is no earth connection 5 Mains cables must not come into contact with other cables 6 Do not operate the projector with wet hands or in an area where water is present 7 The fixture must never be located in an exposed position or in areas of extreme humidity Protection against ultraviolet radiation UV 1 Never turn on the lamp if any of the lenses filters or the plastic housing are damaged their shielding functions will only operate efficiently if they are in perfect working order 2 Never look directly in the direction of the lamp when it is operating Safety 1 The projector must always be installed with bolts clamps or other fixing devices which are suitably rated to support the weight of the projector 2 Always use a secondary safety fixing device with chain or steel wire of a suitable rating to sustain the weight of the unit in case of failure of the principal fixing point 3 The external surfaces of the unit at various points may reach 150 C Never handle the unit until at least 10 minutes have elapsed since the la
41. up the fixture into a Pan only case or installed on a truss Tilt only 16 English 8 4 Measures The internal microprocessor of the Infinity ACL M allows for several diagnostic and output parameters to be displayed It shows the temperatures detected by the sensors in the base TEMPERATURE Tdriver Tsens 1 Tsens 2 Tsens 3 lt measures main power voltage of the fans VOLTAGE vmain vboard vfan1 vfan2 vfan3 Values over 28 5 V must be considerated as abnormal Reading of the DMX value 0 255 received from each channel used by DMX INPUT MEASURE the fixture on the DMX 512 line Reading of the typical value of the DMX signal called RATE signal DMX RATE update frequency in milliseconds It shows possible ongoing alarm messages ALARM STATUS It shows lamp s status on or with zap effect enabled LAMP STATUS It shows fixture s odometers lamp life r lif e of the lamp resettable lamp life total life ao the lamps installed not resettable unit life USAGE HOURS fixture s life It shows the actual installed software version SOFTWARE VERSION sw LCD master software installed on to LCD master board sw MOTOR slave software installed on to MOTOR slave board It shows the operating information of the ballast Lamp type installed lamp type 575 o 700 W Actual power Instant power in W emitted from the ballast BALLAST MEASURES T1max T2max Max temperatures resettable detected by t
Download Pdf Manuals
Related Search