setup information
Contents
1. INSTALLATION GUIDE Transmitter for gas meters with pulse interface TX PULSE HP ATEX 400 006 IG UK 400 006 a Expert Wireless M2M 33 0 5 56 35 97 47 contact enless fr www enless fr Enless Wireless On T DECLARATION CE DE CONFORMITE EC DECLARATION OF CONFORMITY CE amp Enless Wireless We Enless Wireless 45 ter avenue de Verdun 33520 Bruges France Declare under our sole responsibility that the product Designation Radio transmitters Product Name s amp References TX PULSE HP ATEX 400 006 Attestation LCIE 14 ATEX 3013 X Notifi e par le LCIE 33 avenue du G n ral Leclerc 92260 Fontenay aux Roses France Num ro LCIE 0081 To which this declaration relates satisfy the provision of Directive ATEX 94 9 EC of the European parliament and the council of 23 March 1994 gt is in conformity with the following standard s or other normative document s e EN60079 0 2012 EN60079 11 2012 The marking is H1 amp GExiallCT3 Ga Fulfill the directives amp standards e RTTE 99 5 EC of 9 March 1999 e RoHS 2011 65 EU of 1 July 2011 e EN300 220 1 amp 2 V2 4 1 2012 05 e EN301 489 1 V1 9 2 2011 09 EN 301 489 3 V1 4 1 2002 08 e EN 60950 1 2006 A11 2009 A12 2011 AC 2011 e EN 5081 2012 e EN61000 4 2 2009 Date 05 05 2014 Bruno Petit G rant REMINDER REGARDING INSTALLATION OF TX PULSE HP ATEX 400 006 Referring to ATEX Dire2. IVER Connect the battery to the battery connector LED indicators L1 L2 amp L3 will blink simultaneously L1 will blink every 3 seconds TX PULSE ATEX 400 006 is now entering configuration installation mode TX PULSE ATEX 400 006 will try to connect to the RX USB or RX MODBUS Receiver during 1 minute maximum If LEDs don t blink when connecting the battery and pulling out the paper disconnect the battery and try again If TA PULSE ATEX 400 006 is within the range of RX USB or RX MODBUS Receiver successful installation configuration messages as well as RSSI Radio signal strength will be displayed in the message window of FCT software The combination of L1 L2 and L3 LED indicators will confirm success or failure of the installation See below L1 L2 and L3 LED INDICATORS COMBINATION SUCCES OF INSTALLATION L2 amp L3 LED indicators will remain ON for 30 seconds confirming the success of the installation Transmitter is connected to RX USB or RX MODBUS Receiver Transmitter will then switch to communication mode It will send its data at defined periodicity 5 minutes default periodicity L1 LED indicator will blink every minute L2 LED indicator will blink every time data will be sent from the transmitter to the receiver SUCCESS OF THE INSTALLATION BUT LOW RSSI SIGNAL L1 L2 amp L3 LED indicators will remain ON for 30 seconds confirming the success of the installation Transmitter is connected to the RX USB or RX MODB
3. US receiver However L1 LED ON confirm that the RSSI signal is low 85 dBm or less Message FCT Installation is successful for Transmitter address Transmitter will then switch to communication mode It will send its data at defined periodicity 5 minutes default periodicity L1 LED indicator will blink every minute L2 LED indicator will blink every time data will be sent from the transmitter to RX USB or RX MODBUS receiver FAILURE OF THE INSTALLATION After 1 minute the transmitter failed to connect to RX USB or RX MODBUS receiver L2 amp L3 LED indicators will blink for 30 seconds meaning the transmitter is not within the range of RX USB or RX MODBUS receiver There is no message displayed on FCT software Transmitter will then switch to communication mode It will try to send its data at defined periodicity L1 LED indicator will blink every minute L2 LED indicator will blink every time data will be sent from the transmitter to RX USB or RX MODBUS receiver In case of installation failure Move the RX USB or RX MODBUS receiver antenna in order to optimize radio propagation D Move the transmitter if you can and try the procedure again If the problem remains you will have to install a repeater between transmitter and RX USB or RX MODBUS receiver CLOSE TX PULSE ATEX 400 006 TRANSMITTER ENCLOSURE Close the lid using the 4 screws CHECK DATA RECEPTION FROM TX PULSE ATEX 400 006 WITH FCT SOFTWARE With FCT
4. city retry pulse count 1 and pulse count 2 Tx Pulse Tx Time 1 to Address 250 min Re try Oor 1 Pulse Counti Pulse Count 2 11200039 5 0 0 0 Then click on OK to add these transmitters to your configuration file 9 Click on Start Configuration You can now install the TX PULSE ATEX 400 006 transmitter INSTALLATION OF TX PULSE ATEX 400 CONNECT TX PULSE ATEX 400 006 TO THE METER TX PULSE ATEX 400 006 is provided with 4 wires allowing connection up to two meters Meter 1 input 1 Input 1 wires are labeled A and A A is connected on terminal block to PULSE 1 INP A is connected on terminal block to GND Meter 2 input 2 Input 2 wires are labeled B et B B is connected on terminal block to PULSE 2 INP B is connected on terminal block to GND Length of the wires 150 cm You should avoid extending the length of these wires because of potential interferences which could generate wrong pulses INSTALL TX PULSE ATEX 400 006 e Set TX PULSE ATEX 400 006 at least 1 5 meter above the ground e Fix TX PULSE ATEX 400 006 v Wall mounting with 2 brackets amp or v Collar mounting with 2 brackets or v DIN Rail 1 adaptor to be fitted at the back of TX PULSE ATEX 400 006 enclosure TX PULSE ATEX 400 006 must always be installed with antenna upwards OPEN TX PULSE ATEX 400 006 ENCLOSURE Open the lid using the 4 screws START RADIO COMMUNICATION BETWEEN TX PULSE ATEX 400 006 AND RECE
5. ctive 1999 92 CE only operators trained for risk areas are allowed to install TX PULSE HP ATEX 400 006 No changes to TX PULSE HP ATEX 400 006 are allowed Special conditions for a safe installation TX PULSE HP ATEX 400 006 shall only be connected to intrinsically safe certified eguipment This combination must be compatible as regard intrinsic safety rules Uo lo Po Co Lo specified on TX PULSE HP ATEX 400 006 label Certifications TX PULSE HP ATEX 400 006 is ATEX certified lt Ex gt ll1G Ex ia llC T3 Ga 20 C lt Tamb lt 55 C LCIE 14 ATEX 3013 X Uo 3 9V lo 2 55A Po 765mW Co 63uF Lo 5 5uH TX PULSE HP ATEX 400 006 complies with standards EN60079 0 et EN6079 11 Battery Le TX PULSE HP ATEX 400 006 with LS33600 D type battery Only LS33600 D type battery can be used with TX PULSE HP ATEX 400 006 Contact details for supplying LS33600 batteries Enless Wireless 45 ter avenue de Verdun 33520 Bruges France Telephone 33 0 5 56 37 97 47 Email contact enless fr WARNING DANGER POTENTIAL ELECTROSTATIC CHARGES TX PULSE HP ATEX 400 006 must only be cleaned with damp rag pal YW6L Agg i anssi lapeg DUIA 82000 22 CONFIGURATION OF THE TX PULSE ATEX 400 FCT Field Configuration Tool software allows installation of the transmitters and configuration of RX MODBUS Receiver Please refer to FCT user manual available on www enless fr 1 Position your la
6. ptop PC to the place where you intend to install the RX USB or RX MODBUS receiver FCT software is running on your PC 2 Connect the RX USB or RX MODBUS receiver to the USB port of your PC If you are using RX MODBUS Receiver for the installation of the transmitters switches DIP 1 amp DIP 2 must be configured the following way e DIP1 switches 5 amp 6 ON all other switches OFF e DIP2 switches 1 2 amp 3 OFF Please refer to FCT manual for the complete installation of RX MODBUS Receiver 3 Fit the antenna on RX USB or RX MODBUS SMA connector 4 Start FCT software on your PC Select English and type your user name Enless Wireless Expert Wireless M2M Enless Field Installation v2 1 Please enter your name to continue Enless 5 Click on Refresh list The USB COM Port you have connected the receiver to will be selected 6 Click on Connect The receiver is now connected to the PC ready to receive data from TX PULSE HP ATEX 400 006 Ss Connect Message in the dialog box Serial Port Connected COMx xxxxx 7 Select the family of the transmitters you want to install For this product you have to select Tx Pulse tab then click on Edit View 52 Edit View A new window will open 8 Click on this button to add the TX PULSE ATEX 400 006 transmitter e Fill in the ID in the Address field Important this ID is composed of 8 numbers e Define periodi
7. software you will be able to check that data from TX PULSE ATEX 400 006 are received correctly by RX USB or RX MODBUS Receiver Click on Stop configuration Then click on View network You will see data from the TX PULSE ATEX 400 006 displayed on FCT software Expert Wireless M2M Configuration Clear Data Device Type Time Device ID Data 1ID Data 1 Data 21D Data 2 RSSI dBm Battery TX PULSE 19 juin 15 12 01 45 11300138 CSTD Pulse Count1 0011 0 CSTD Pulse Count 2 om o 41 0 TX PULSE pueg 12 00 44 11300138 CSTD Pulse Count 1 0011 0 CSTD Pulse Count 2 TE ik E i ge hb i Search by ID Enless Wireless TXPULSE 19 juin 15 11 59 40 11300138 CSTD Pulse Count 1 0011 0 CSTD Pulse Count 2 0011 0 41 0 OK DEVICE TYPE TX PULSE TIME Date amp Time of data transmitted by TX PULSE ATEX 400 006 DEVICE ID Unique 8 digit address from TX PULSE ATEX 400 006 DATA 1 ID Pulse count 1 DATA 1 Data received by the receiver DATA 2 ID Pulse count 2 DATA 2 Data received by the receiver RSSI SIGNAL Radio signal strength dBm between TX PULSE ATEX 400 006 transmitter and RX USB or RX MODBUS Receiver gt from 10 to 50 dBm excellent radio guality signal gt from 50 to 85 dBm good radio quality signal gt from 85 dBm and lower low radio quality signal BATTERY Level of battery
Download Pdf Manuals
Related Search