CCTV Camera Manual
Contents
1. d B W Camera gt BM STD Res Series 420 TV Lines 0 05 Lux F1 2 DC12V Only DC12V AC24V Non polarity Dynamic power input AC230V AC200 AC240V E Hi Res Series 600 TV Lines 0 1 Lux F1 2 DC12V Only DC12V AC24V Non polarity Dynamic power input AC230V AC200 AC240V m Hi Res EX view Series 600 TV Lines 0 001 Lux F1 2 with EX view HAD CCD DC12V Only DC12V AC24V Non polarity Dynamic power input AC230V AC200 AC240V This unit has been tested and proved to comply with the limits of FCC rules and CE regulation Warning To prevent the risk of fire or shock hazard do not expose this camera to water Installation of this unit should be carried out by a qualified personnel and should conform to the local codes Precautions Do not drop or shake the carton severely The box cannot give perfect protection against heavy shocks Do not touch the CCD glass by hand as this may give a blurred picture Do not expose the camera to water or other liquids It can cause fire or electric shock If water or other liquids contaminate the unit dry it quickly as it can corrode the electrical components inside Do not install the camera in the wet area or area of high humidity without adequate protection Moisture can corrode the electrical components inside Do not turn the camera to face strong light Direct sunlight or strong reflected light can cause blooming or smearing of the picture Do not install or2. BNC BNC Power Indicator Red LED Red LED Red LED Red LED Red LED Red LED Rear Power Input terminal Screw Joint Screw Joint 230VACVDECode Screw Joint Screw Joint 230V AC VDE Code Pannel Line phase push BTN x Up Down Up Down x Up Down Up Down W B adjust push BTN Up Down Up Down Up Down Up Down Up Down Up Down Dip S W 6 Way 6 Way 6 Way 6 Way 6 Way 6 Way Side Auto Iris jack 4Pin Jack 4Pin Jack 4Pin Jack 4Pin Jack 4Pin Jack Arn Jack Panna ris Mode Slide SW VI ES DC VI ES DC VI ES DC VI ES DC VI ES DC VI ES DC DC Iris Adjust volume DC Level DC Level DC Level DC Level DC Level DC Level e Specification B W MODEL STD Res Series Hi Res Series Image sensor 1 3 Interline CCD SONY ii SL Vario Effective Pixels EIA 512 H X492 v CCIR 500 H X582 V EIA 768 H X494 V COIR 752 H X582 V H Resolution 420 TV Lines 600 TV Lines Synchronizing system Internal Intemal Line Lock Internal Internal Internal Line Lock Internal Scanning system EIA 525 Lines CCIR 625 Lines 2 1 Interlaced Video output 1 0Vp p Composite 75 Ohms S N ratio More t
3. Please check if the monitor s contrast is set too dark Please check if the Gamma select switch is set to 1 0 on the 6 pin of the DIP switch If it is please move it to the 0 45 position Gamma 1 0 position is recommended for use with a LCD monitor Please check if the camera is positioned toward a door or window Please set BLC ON is these conditions O When the picture is too bright Please check if the monitor s brightness control is get too high Please check if the camera is set to BLC ON under normal lighting conditions i e when the camera is not pointed towards a brightly lit area Please move the BLC select switch to the BLC OFF position When there is noise on the picture in dark illumination conditions The camera picture becomes noisy under AGC MAX mode in order to increase the video gain in poor lighting conditions Please move the AGC switch to OFF position if it is not required When the picture is not clear on the monitor Please check if the monitor is set up correctly Please check if the camera is pointer towards an area where too much light comes in Adjust the direction of the camera in this case Please check if the back focus of the lens is set correctly When the picture is flickering Please check if the camera is pointed at fluorescent lighting or bright sunlight Use a visor or adjust the direction of the camera in this case Please check if the Auto iris lens is selected correctly on the IR
4. use the camera in an environment of extreme temperature In temperatures of below 10 C use an external housing with heater built in In a temperatures of over 60 C cool the camera with ventilation apparatus Do not disassemble the camera There are no user serviceable parts inside Name of each part amp Functions gt TE CCD Protection Cover Leave the cover in place when the lens is not installed Take it off to fit the lens C amp CS mount This holder moves back and forth by sliding the adjustment lever forwards or backwards This mechanism is designed for the purpose of using all types of C Mount or CS Mount lenses of different manufacturers Mount the lens on the holder firmly It is set to CS Mount position at the factory Loosen the adjustment lever by turning it counter clockwise a little bit in order to adjust the C amp CS mount holder Set the focus and lock the lever Adjustment Lever Flange back focus alignment area for C Mount lens The mount offers 0 5mm of extra tolerance to enable any type of non standard C Mount lens to be focused Loosen the adjustment lever by turning it counter clockwise a little bit for fine tune focus Flange back focus alignment area for CS Mount lens The mount offers 0 5mm of extra tolerance to enable any type of non standard CS Mount lens to be focused Loosen the adjustment lever by turning it counter clockwise a little bit for fine tune focus G 0
5. y 1 0 by Dip Switch White Balance Standard 2100 K 9100 K Auto anual setting by Dip S W amp Up Down by Push BTN Gain Control Standard 8dB 30dB Auto Maximum by Dip switch Smear Effect 0 005 MTBF 80 000 hours Power source DC12V DCT2V AC24V Dynamic AC230V DC12V DC12 A024 Dyname AC230V Operating current 130mA 150mA 110MA 30mA SOMA 150mA 110mA 30mA Lens C Mount 17 5mm Frange back CS Mount 12 5mm Frange back amp Fine focus 1 0mm Iris Control Video Iris ESC DC Iris Operating Temperature 14 F 122 F 10 C 50 C Humidity Within 90 RH Measurement mm 50 W x 50 V x 115 L Weight Approx g 310 310 410 310 310 410 R Sensitivity Yes Yes Yes Yes Yes Yes Optional Audio Yes Yes Yes Yes Yes Yes Features Dual Power 12 24 12V DC Only Yes x 12V DC Only Yes x Line Lock x Yes Yes x Yes Yes BLC ON O ON O ON O ON O ON O ON O Dip SAW AGC STD MAX STD MAX STD MAX STD MAX STD MAX STD MAX Control Gamma 0 45 1 0 0 45 1 0 0 45 1 0 0 45 1 0 0 45 1 0 0 45 1 0 WBA WBM White Balance Auto WB Manual adjustment Line Lock x ON O ON x ON O ON Video Ou BNC BNC BNC BNC
6. 9 Color 6 Mounting the Bracket Holder DC 12V AC 24V Can be attached either on the top or on the bottom Assemble it with the Line Lock screws provided 3 EA 1 6Way Dip Switch 3 Video Out Connector Al BNC Female 7 Auto iris lens connector Please refer to page 13 14 of this manual for the wiring specification 4 Power Indicator 8 Iris mode select switch 2 Power Input AAT 18 9 Y size ES Electronic auto iris VI Video iris DC DC Iris Terminal Balance Push bu en ES mode is used with manual iris lenses In ES mode the camera controls NDA the electronic shutter automatically from 1 50 to 1 100 000 sec PAL CCIR or 1 60 to 1 100 000 sec NTSC EIA ES mode with a Manual iris lens is suitable for indoor surveillance Select the slide SW to the ES position AC 230V Power Cord For outdoor use ES mode is not sufficient In this case an Auto Iris lens of either Video driven type or DC driven type is recommended Move the slide SW to VI position for the Video iris lens or move it to DC position for the DC Iris lens When VI or DC mode is selected the electronic shutter speed is fixed to 1 50sec PAL CCIR or 1 60sec NTSC EIA PHASE 10 y 8 MANU 9 DC Level control for DC Iris lens 1 1 6 Way DIP Switch It is used for controlling the video output level of the DC driven auto iris DIP Switc
7. AC 230V Power Cord DC 12V Line Lock Cord VIDEO POWER S TITT AC230V 1 4 Pin DIP Switch DIP Switch configuration 24V AC LineLock Nol_ ORR gt I aa EN Y DIP Switch configuration DC 12V 8 230V AC y 0 45 y 1 0 BLC ON BLC OFF AGC Normal 20dB AGC Max 32dB B W 4 Way Dip Switch Functions Sync Mode Selection L L I INT INT Internal Sync Mode This mode is used when the camera is installed outoor with one camera to one monitor operation L L Line Lock Mode To work with other cameras using 24VAC power it is required to synchronize the video signals in order to remove picture fluctuation problems In the case of one camera with one monitor under fluorescent lighting the picture is affected by the 24VAC power frequency in INT mode A flickering picture may result from this condition Set Dip S W to L L mode to remove this problem It is set to L L at the factory Gamma Correction Select Mode y 0 45 I 11 0 Select 1 0 when the picture needs to be darker in contrast It is set to 0 45 at the factory Automatic Gain Control AGC MAX Use this mode for dark illumination or at night If the MAX AGC Max is selected the camera increases the video signals to maximum so that the picture looks brighter At MAX mode unnecessary noise is increased also and the picture may display noise on the screen This is normal It is set to AGC at the facto
8. CCTV Camera Manual Table of Contents Model configuration Pr ecautions elia Name of each part and Functions Front Back Connection 1 Lens 1 How to use a Fixed Iris IANS 0 00 2 How to use a DC Iris lens 3 How to use a Video Iris lens 4 How to connect an Auto Iris lens 2 How to adjust C CS MOUNU eni veden ee 3 How to connect Power 4 How to connect Monitor s o s o ssesee rer reerer rer rer rer cee rer sen ora Specification Color Camera Trouble shooting guide sessessersereer rer ser rer ser ner srr one nen ees Note 12 12 13 13 13 14 15 16 17 18 19 20 21 22 Please study the manual thoroughly in order to get the best performance from the camera Model configuration Color Camera mw STD Res Series 400 TV Lines 0 01 Lux F1 2 DC12V Only DC12V AC24V Non polarity Dynamic power input AC230V AC200 AC240V I STD Res EX view Series 400 TV Lines 0 001 Lux F1 2 with EX view HAD CCD DC12V Only DC12V AC24V Non polarity Dynamic power input AC230V AC200 AC240V E Hi Res Series 500 TV Lines 0 03 Lux F1 2 DC12V Only DC12V AC24V Non polarity Dynamic power input AC230V AC200 AC240V E Hi Res EX view Series 500 TV Lines 0 001 Lux F1 2 with EX view HAD CCD DC12V Only DC12V AC24V Non polarity Dynamic power input AC230V AC200 AC240V E Option 1 IR Sensitive for Day 8 Night application Model nr IR 2 Flickerless Function Model nr FL
9. DC 40V or within AC 15V AC 30V It is not a special requirement to use a regurated power supply but using a regurated supply is recommended 1 3 Video Out Jack BNC Female Connect Coaxial cable from this BNC connector to the monitor Use a high quality coaxial video cable to ensure good picture quality over long distances 1 4 Power Indicator Red power lamp turns on when the power is properly supplied 1 5 Vertical Phase Adjustment Push Button Line Lock mode White Balance Push button The up down push buttons control V phase at L L mode and control manual white balance at the WBM mode At the L L Mode When the unit is used with system equipment and other cameras it is required to synchronize the Vertical Phase between the cameras when using 24VAC It is recommended to use a multi channel oscilloscope for correct adjustment Push the buttons once at a time up or down when vertical phase of the unit does not match the other cameras or system equipment At the WBM White Balance Manual Mode Adjust the white balance with the push buttons when the camera is used with the special lighting such as sodium lamps Usually it is not used for security applications These two functions cannot be adjusted at the same time Adjust each mode in turn EXI B W DC 12V AC 24V Line Lock a 3 Video Out Connector 7 BNC Female POWER 4 Power Indicator PHASE 5 V R DO
10. I ES DC VI ES DC VI ES DC VI ES DC VI ES DC DC Iris Adjust volume DC Level DC Level DC Level DC Level DC Level DC Level Trouble Shooting Guide If the unit continues to be fault after the following adjustments please consult your dealer When the picture is not displayed on the monitor Please check if the AC DC power unit is plugged into the AC power outlet firmly Please check if there are any misconnection s in the cabling Please check if the IRIS mode select switch is set to the correct position i e to the DC mode for the DC driven auto iris lens or VI mode for the Video driven auto iris lens When the picture is blurred Please check if the lens is contaminated Please clean the lens surface on both sides gently with a soft cloth or tissue Please check if the lens is focused properly When you use a manual iris lens the iris select switch should be positioned to the ES mode Please check if the monitor is set to brightly Adjust the brightness or contrast level on the monitor correctly When the color displayed on the monitor is not correct for Color Please check if the White Balance switch is set to WBM position White balance is controlled automatically under the WBA mode for most situations When the camera is used under special lighting conditions please refer to page 7 in this manual Please check if the monitor s color adjustment is set correctly When the picture is too dark
11. IS mode select switch Please move the Iris mode switch to DC position when you use a DC type auto lens or move it to the VI position when you use a Video type auto iris lens When you don t use an auto iris lens please move the iris select switch to the ES position When the picture is distorted Please check if the lens is defective and replace the lens in this case Please check if the camera is PAL CCIR 50Hz in an NTSC EIA 60Hz area or vice versa Note
12. h configuration 24V AC LineLock 230V AC LineLock only lens To make the image brighter turn the pot clockwise To make the image darker turn the pot counter clockwise 1 Phase Push SW up down Line Lock Mode Mode pl OFF Manual White Balance Auto White Balance a Adjust the Push Button Up Down aa No need to Adjust the Push Button O OB AGC Max 26dB AGC Normal 20dB 6 BLC OFF BLC ON S am configuration DC 12V only ee I i Manual white Balance a White Balance Zo Adjust the Push Button Up Down No need to Adjust the Push Button Po yA P0450 a AGC Max 26dB iL E Normal 20dB Ps store BIGON a NGO Color 6 Way Dip Switch Functions Sync Mode Selection L L i INT INT Internal Sync Mode This mode is used when the camera is installed outoor with one camera to one monitor operation L L Line Lock Mode To work with other cameras using 24VAC and 230VAC power it is required to synchronize the video signals in order to remove picture fluctuation problems In the case of one camera with one monitor under fluorescent lighting the picture is affected by the 24VAC and 230VAC power frequency in INT mode A flickering picture may result from this condition Set Dip S W to L L mode to remove this problem It is set to L L at the factory White Balance Control W WBA White Balance Auto mode B HB M A The camera controls the white balance automatically It i
13. han 50 dB AGC Off l ock 0 1 Lux at F1 2 id E Option 0 001 Lux at F1 2 EX View HAD CCD version BLC ON OFF by Dip Switch Shutter Speed EIA 1 60 1 100 000 sec CCIR 1 50 1 100 000 sec Gamma correction Standard y 0 45 Switchable y 1 0 by Dip Switch Gain Control Standard 4dB 30dB Auto Maximum by Dip switch Smear Effect 0 005 MTBF 80 000 hours Power source DC12V DCIVAC2M 4 Dual AC230V 30V DO12V DCIA AC2AV 4 Dual AC230V 30V Operating current 110mA 100mA 50mA 20mA 10mA 100mA 50mA 20mA Lens C Mount 17 5mm Frange back CS Mount 12 5mm Frange back amp Fine focus 1 0mm Iris Control Video Iris ESC DC Iris Operating Temperature 14 F 122 F 10 C 50 C Humidity Within 90 RH Measurement mm 50 W x 50 V x 115 L Weight Approx g 310 310 410 310 310 410 Line Lock x ON O x x ON O x Dip S W Gamma 0 45 1 0 0 45 1 0 0 45 1 0 0 45 1 0 0 45 1 0 0 45 1 0 Control BLC ON O ONO ON O ON O ON O ON O AGC STD MAX STD MAX STD MAX STD MAX STD MAX STD MAX Video Out BNC BNC BNC BNC BNC BNC Rear Power Indicator Red LED Red LED Red LED Red LED Red LED Red LED Pannel Power Input terminal Screw Joint Screw Joint 230VAC VDE Code Screw Joint Screw Joint 230V AC VDE Code Phase V R x YES x x YES x Dip SAV 4Way Slide 4Way Slide 4Way Slide 4Way Slide 4Way Slide 4Way Slide Side Auto Iris jack 4Pin Jack 4PinJack 4Pin Jack 4Pin Jack 4Pin Jack 4Pin Jack Parigi ris Mode Slide SAW VI ES DC V
14. ity shielded coaxial video cable to avoid noise interference Connect the cable with the power turned off e Camera Back Monitor When the camera is used with multi channel equipment or with more than 2 monitors please set impedance level switch on the interim equipment monitors to HI Z position and make sure to set the last monitor to 75 2 position INTERIM EQUIPMENTS OR MONITOR LAST MONITOR CAMERA Specification Color MODEL Image sensor 1 3 STD Res Series Hi Res Series SONY HAD IT CCD Option 1 3 EX View HAD CCD SONY Effective Pixels NTSC 512 H X492 V PAL 500 H X582 V NTSC 768 H X494 V PAL 752 H X582 V H Resolution 400 TV Lines 500 TV Lines Synchronizing system Internal Intemal Line Lock Line Lock Only Internal Internal Line Lock Line Lock Only Scanning system NTSC 525 Lines PAL 625 Lines 2 1 Interlaced Video output 1 0Vp p Composite 75 Ohms S N ratio ore than 50 dB AGC Off Min Illumination STD 0 01 LuxatF1 2 High Res 0 03 Lux at F1 2 EX View 0 001 Lux at F1 2 BLC ON OFF by Dip Switch Shutter Speed NTSC 1 60 1 100 000 sec PAL 1 50 1 100 000 sec Gamma correction Standard y 0 45 Switchable
15. ry BLC Back Light Compensation ON OFF BLC IH 10FF Under bright lighting conditions from behind the subject the camera will close the iris automatically Select BLC mode to counteract this In normal lighting conditions select BLC to OFF It is set to OFF at the factory 2 2 Power Input Terminal This terminal provides connections for DC 12V or AC 24V It is not polarity sensitive The unit has a wide power tolerance within DC 10V DC 40V or within AC 15V AC 30V It is not a special requirement to use a regurated power supply but using a regurated supply is recommended 2 3 Video Out Jack BNC Female Connect Coaxial cable from this BNC connector to the monitor Use a high quality coaxial video cable to ensure good picture quality over long distances 2 4 Power Indicator Red power lamp turns on when the power is properly supplied 2 5 Vertical Phase Adjustment V R Line Lock mode 4 At the L L Mode When the unit is used with system equipment and other cameras it is required to synchronize the Vertical Phase between the cameras when using 24VAC It is recommended to use a multi channel oscilloscope for correct adjustment Adjust vertical phase of the unit with V R to match with other cameras or system equipment Connection 1 Lens It is recommended to use a good quality lens to improve the picture quality under low light conditions The camera is built with a universal mounting mechanism on which any type of len
16. s can be used Lens is not supplied with camera 1 1 How to use a Manual Iris lens In this set up the camera does not control the iris Instead the camera adjusts the picture automatically for light changes Set the Iris mode select switch to ES Electronic Shutter position Please make sure to check this before operation When the S W is positioned at the VI or DC mode the electronic shutter will be off and will not control the picture 1 2 How to use a DC Iris lens oS E i VI ES DC 1 E Do N E vow amp UP E no Or Set the iris mode select switch to DC DC driven automatic iris Control position In this mode the iris is controlled automatically to react to DC signals from the camera Please make sure to set S W to DC position before you operate the camera with a DC lens DC level control is on the side of the camera Please do not touch the DC Level control when using a fixed or Video iris type of lens The camera is set to DC at the factory Adjust the pot up or down only when you need the picture to look brighter or darker depending on the situation Generally there is no need to adjust the level 1 3 How to use a Video Iris lens Set the iris mode select switch to VI Video signal driven Automatic Iris position In this mode the lens controls itself automatically to react to Video signals from the camera Please make sure to set S W to VI position before
17. s recommended for most applications It is set to WBA at the factory W B A White balance is controlled manually under this mode by adjusting the push button up or down It is not used for normal applications It may needed for special conditions or when the camera is used under special lighting The back ground of the picture may become red or blue under manual adjustment W WBM White Balance Manual Mode B En N Gamma Correction Select Mode y 1 0 0 45 Select 1 0 when the picture needs to be darker in contrast It is set to 0 45 at the factory lt Option Flickerless Select Mode ONCE FL OFF FL ON NTSC 1 100 sec PAL 1 120 sec Automatic Gain Control MAX AGC Use this mode for dark illumination or at night If the MAX AGC Max is selected the camera increases the video signals to maximum so that the picture looks brighter At MAX mode unnecessary noise is increased also and the picture may display noise on the screen This is normal It is set to AGC at the factory BLC Back Light Compensation ON OFF BLC IH ON Under bright lighting conditions from behind the subject the camera will close the iris automatically Select BLC mode to counteract this In normal lighting conditions select BLC to OFF It is set to OFF at the factory 1 2 Power Input Terminal This terminal provides connections for DC 12V or AC 24V It is not polarity sensitive The unit has a wide power tolerance within DC 10V
18. ver forward and fix it on the C position Turn the lever clockwise to tighten SS ES Hold the levers at both side together and move the lens mount holder forward or backward HIGH PERFORMANCE CCD CAMERA Refer to page 4 for any additional information 3 How to connect power 3 1 Please check the model and power specification before connecting the power 3 2 AC24V power Color B W The camera has a EE AA common power input VIDEO rt gt connector for both 8 ch 8 12VDC and 24VAC Sp sec un SF The power input is O O non polarized PHASE Sa t e va i 12V 3 3 The unit has a ma J wide power tolerance within DC 10V DC S 40V or within AC 15V AC 30V a VIDEO 0 45 10 BLC ON AGC T MAX Nc I nc POWER O 3 4 DC 12V power Use regulated DC 12V power supply ONLY The power ASA input is non polarized UA 3 5 AC 230V power Use an AC 230V 0 45 10 power source Eo Connect the power IED come ME power plug to the outlet om O O directly E r PHASE I WB WARNING CONNECT POWER ONLY AFTER INSTALLATION IS COMPLETED 4 How to connect to monitor 4 1 Connect the Video out jack to the Video In jack on the monitor Use good qual
19. you operate the unit with a Video type auto iris lens Level control is on the side of the lens 1 4 How to connect an Auto Iris lens DC Video Take off the insulation of the lens cable as shown on the drawing approx 8mm Take off the insulation of the inner cable as shown on the drawing approx 2mm connector supplied with the camera and SZ Cover solder the lens cable to the pins as per N LD Lens cable the following configuration N vs Connector Pd F hi n 1 on gt EDS IRIS SIGNAL VCC M DRV DANP Video typ DC typ Video type DC type No 1 Pin Red Power source No 1 Pin DAMP No 2 Pin N C No 2 Pin DAMP No 3 Pin Drive No 3 Pin Yellow Video Signal No 4 Pin Drive No 4 Pin Black GND 1 5 Remove the Protection Cap and attach the lens to the camera 1 6 Set the Iris mode select switch S W to VI ES or DC 1 7 Connect the lens plug to the auto iris socket located on the left side of the camera o 2 How to adjust C amp CS Mount C Mount TS Turn the Lever CS Mount HIGH PERFORMANCE SVAR CCD CAMERA DOWN up DC LEVEL 2 1 Loosen the lens mount holder by turning the adjustment lever clockwise 2 2 Pull the adjustment lever backward and fix it on the CS position Turn the lever counter clockwise to tighten 2 3 Push the le
Download Pdf Manuals
Related Search