Manual - Richard Martin Lighting
Contents
1. EXOTIC SANGRIA LEE Ref LEE 101 LEE 103 LEE 105 LEE 106 LEE 107 LEE 111 LEE 113 LEE 115 LEE 116 LEE 119 LEE 128 LEE 132 LEE 134 LEE 135 LEE 136 LEE 147 LEE 180 LEE 156 LEE 079 LEE 194 LEE 024 LEE 017 LEE 019 LEE 108 LEE 126 LEE 141 ROSCO Ref ROSCO 378 ROSCO 358 ROSCO 081 ROSCO 066 ROSCO 030 ROSCO 318 ROSCO 332 ROSCO 034 ROSCO 039 Safety Information Warning Class 2M LED product Do not look into the beam from a distance of less than 40 cm 16 inches Do not stare into the beam for extended periods at a short distance Do not view the beam directly with optical instruments This product is for professional use only It is not for household use This product presents risks of severe injury or death due to fire hazards electric shock and falls READ THIS MANUAL before installing powering or servicing the fixture follow the safety precautions listed below and observe all warnings in this manual and printed on the fixture If you have questions about how to operate the fixture safely please contact Global Design Solutions www gds uk com PROTECTION FROM FIRE e Provide a minimum clearance of 0 1m 4 around fans and air vents e Do not modify the fixture or install other than genuine GDS parts e Donot stick filters masks or other materials directly onto LEDs e Do not operate the fixture if the ambient temperature Ta exceeds 40 C 104 F PROTECTION FROM INJURY The LED emission pre2. Global Design Solutions ite 6 High Output ban b Z uk Ari RGB Battery Uplighter With Wireless DMX Supplied Items 1 x LiteWare HO Unit Instruction Leaflet Battery Charger single unit only Mains Lead single unit only Aerial Introduction LiteWare HO with wireless DMX is a stand alone light source The unit can be controlled by DMX transmitted wirelessly and in stand alone operation using 50 preset colours and 20 preset fade and snap seguences Features e Full RGB with 16 bit dimming curve e Wireless DMX Control e Up to 12 hour runtime from fully charged battery 5 hours full white e 50 preset colours e 20 preset colour chases e Charging Cycle Approximately 8 hours e Wireless Firmware Update Conformity LiteWare HO conforms to the following standards EN 61000 6 3 Light Industrial Emissions EN 61000 4 2 Heavy Industrial Immunity Further information can be obtained from technical gds uk com Manufactured in the UK by Global Design Solutions www gds uk com info gds uk com Switching the Unit ON To turn the unit ON or OFF the TOP Button needs to be pressed and held for 1 5 Seconds the button LED will illuminate to show the unit is awake When the battery voltage becomes too low the unit will go to sleep and pulse the top button LED The unit can t be switched back on until it has been recharged Address Settings The address of the unit is set using 2 push buttons on the base These are l
3. abelled UP and DN Pushing the UP button will increment the address pushing the DN button will decrement the address If the unit is at 001 and you press the DN button it will remain at 001 If you hold one of the buttons the address will slowly increment decrement gradually speeding up When the address reaches 510 it will stop at the boundary You must then release the button and push it once again to get to address 600 These boundaries are intended to make the addressing easier to navigate The boundaries are DMX Mode 1 510 Wireless DMX Mode Address Stand Alone Mode 601 650 Fixed Colour Mode 651 660 Colour Fade Sequence 661 670 Colour Snap Sequence The display will blank after 5 seconds of button inactivity Wireless DMX Mode Address 1 510 In WDMX Mode the unit will simply respond to the DMX levels being received DMX channel allocations are as follows Start Address Red Level Start Address 1 Green Level Start Address 2 Blue Level In WDMX mode the unit will hold the last DMX value upon loss of signal or DMX The unit will store this level when turned off so it can be resumed when it is powered back up If the battery is disconnected these values will be lost WDM lt x Linking LiteWare HO is automatically unlinked from the transmitter when plugged into the charger The link status is shown on the LED display on the base of the unit when LiteWare HO is powered on Please refer to your W DMX transmitter user manua
4. harger Simply plug the supplied charger into the base of LiteWare HO During charging the button LED will be on constantly and when the units are fully charged the LED will flash Leaving the LiteWare HO connected to the single charger without the charger connected to the mains will flatten the battery Battery Care The LiteWare HO Uplighter contains a Sealed Lead Acid battery The battery should not be left in a discharged state for long periods because it will reduce its capacity We recommend leaving LiteWare UL on charge permanently when not in use If removing the battery please observe the correct polarity upon re connection Fixed Colour Table ADDRESS 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 COLOUR RED GREEN BLUE YELLOW CYAN MAGENTA ORANGE GOLD PINK VIOLET AQUA SKY BLUE FULL WHITE COOL WHITE WARM WHITE YELLOW STRAW ORANGE PRIMARY RED LIGHT ROSE DARK PINK MAGENTA BLUE MED BLUE GREEN DARK BLUE BRIGHT PINK MEDIUM BLUE GOLDEN AMBER DEEP GOLDEN AMBER PALE LAVENDER APRICOT DARK LAVENDER CHOCOLATE JUST BLUE SURPRISE PINK SCARLET SURPRISE PEACH FIRE ENGLISH ROSE MAUVE BRIGHT BLUE ALICE BLUE ROSE INDIGO URBAN BLUE COOL BLUE LIGHT SALMON MAYAN SUN CHERRY ROSE FLESH PINK SKELTON
5. l for further information about the linking process In Stand Alone Mode A short push of the TOP button will dim the unit there are 7 output levels When the button is pushed for the 7th time the unit will jump back up to full level Stand Alone Mode Address 600 601 650 FIXED COLOURS Detailed in table on page 4 651 655 COLOUR FADE SEQUENCE 1 A colour fade sequence with 5 different speeds of transition 656 660 COLOUR FADE SEQUENCE 2 A colour fade sequence with 5 different speeds of transition 661 665 COLOUR SNAP SEQUENCE 1 A colour snap sequence with 5 different speeds of transition 666 670 COLOUR SNAP SEQUENCE 2 A colour snap sequence with 5 different speeds of transition Charging System There are two charging methods available for LiteWare HO Both charger options are designed specifically for LiteWare HO Please DO NOT use any other charging system as this can damage the unit Flight Case Charger System Ensure that the flightcase is plugged into a mains supply with the supplied mains lead Place the LiteWare HO into the flightcase and the unit will start charging Whilst charging the button LED will be on constantly it will flash when the battery is fully charged and LiteWare is ready for use Upon disconnecting the mains to the flight case all charged units will continue to flash the button LED This is normal Briefly lifting the unit out of the case and replacing will switch the button LED off Single Unit C
6. sents a hazard to eyesight at a distance of 4 40cm 1 6 16 when the eye is exposed to the beam for longer than 0 25 seconds Do not look at LEDs from a distance of less than 40cm 16 without suitable protective eyewear Do not look at LEDs with magnifiers or similar optical instruments that may concentrate the light output DISPOSING OF THIS PRODUCT Global Design Solutions products are supplied in compliance with Directive 2002 96 EC of the European Parliament and of the Council of the European Union on WEEE Waste Electrical and Electronic Equipment as amended by Directive 2003 108 EC where applicable Help preserve the environment Ensure that this product is recycled at the end of its life Your supplier can give details of local arrangements for the disposal of Global Design Solutions products INSTALLATION Install fixtures on a level stable surface where they do not present a hazard of tripping or falling
Download Pdf Manuals
Related Search