P1301/P1405/P1407 User Manual
Contents
1. Adjust the sensors the right position detected all the time position or angle 3 If the system detected something which is not existed adjustment is needed for the controller peel off the Display a fixed a Ground is Adjust the sensors QC label in the back of controller screw distance detected position or anticlockwise until the signal cleared out b Sensors direction direction is wrong Orientation Sensor s connector is not Check if the indicator not plugged in properly or is connector is firmly on plugged in while power is on connected Then witch on power again Warranty e year e Any physical damage will void the warranty2. Sound Notes Please check the condition behind your car before reversing In some cases the display may be not as same as the reality due to the sensor position obstacle shape reflection condition and so on Some examples are given below As B is under the level of sensors and A is a strong reflecting point the distance of CA will be shown first When the obstacle is within the blind area both A and B will not be detected This will occurs when the obstacle is lower than the level of sensors Due to obstacle A is pretty short so during reversing the distance between sensor and obstacle A shown first After obstacle A is within blind area the distance between sensor and obstacle B will be shown 3 Though A is closer to the car than B the distance from sensor to point B is shown 4 Incase of small angle of incidence to the obstacle such as glass or other smooth plane the obstacle is not detected 5 B will be detected sooner or later but A may not be detected at all 6 The reading may moves up and down between 3 9 feet and 7 2 feet because the low obstacle A is at the critical detecting point The reading will be stable after a little bit closer to the obstacle A 7 On certain conditions for example in case of rough ground ground might be detected instead of object A 8 Not all obstacles is detected from 8 feet for instance a person is detected from 4 26 feet because of the we
3. from installing or use of this system Manufacturer or supplier does not warrant the accuracy or completeness of the information in this documentation and manufacturer or supplier reserve the right to alter specifications without notice To the extent permitted by law manufacturer or supplier exclude all liability including negligence for any loss incurred in reliance on the contents in this publication Warning Please practice reverse parking using different obstacles to test this product s performance Though the minimum detecting distance is 1 15 feet it is still recommended to keep enough space to stop the car Considering the cars inertia it would be better to stop the car when the distance is shorter than 2 feet The reverse speed should be less than 3 miles hour Products information W NH Introduction The system alerts the driver the distance of obstacles while reversing the vehicle It includes 4 sensors 1 waterproof controller and display The system generates both audible and visual warning Features and benefits Accurate measurement and stable readout High sensitivity wide detection range and small blind area Functions include digital display sound alarm zone amp direction indication reverse reminder Self testing The outfit of display unit matches the instrument panel of car Applicable to most cars and easy installation Specifications 1 Operation voltage 2 Power consum
4. P1301 P1405 P1407 User Manual MY BULLY DOG Fi Autero Reverse Backing Systems 866 805 6922 Contents Note Warning Product information Introduction seen Features and benefits Specifications How to use Display Volume Adjustment Precautions 2232222222222 22er ae Zee Sensing Range and Warning Method NO een Zen ee 7 8 Maintenance How to install Tools 10 System Components 10 Installation diagram 11 Installation Procedure 12 Installation of sensors 12 Wire Connection 13 Precaution during installation 14 Final testing 14 Troubleshooting 14 Warranty 14 Note Please read this manual carefully before using this product This system is designed to be an aid and should not replace the need to drive carefully Under no circumstances will the manufacturer or supplier accept any responsibility or can be held liable for any direct or indirect incidental or consequential damage or for injuries resulting
5. ak reflection of clothes The distance form sensor A to B rather than C to D is shown Maintenance 1 Clean up the sand ice snow or any other dirt on sensors surface timely 2 Re paint is allowed on sensors surface with slight coat However extra thick paint may affect detection How to install e Tools System Components P1405 REVERSE BACKING SYSTEMS System Components P1301 System Components P1407 REVERSE BACKING SYSTEMS Reverse BACKING SYSTEMS e Installation diagram 1407 Display rear positioning Reverse Backing SYSTEMS Controller 1405 Display Front positioning _ Sensor Reverse Light P1301 Speaker Front positioning under dash Installation procedures Sensor positioning Interval of sensors Drill holes Mirror symmetry horizontally Sensors are installed on the position Make holes in bumper in accordance with the diagram with included drill bit Controller installation The position of controller me should be appropriate to I Connection both sensors and display Unit Display unit installation Plug display unit into its pedestal and adjust it to suitable position The mounting surface must be clean Connect the controller to 12V power supply sensors and display unit e Installation of sensors Sl IN 3 1 Horizontal position X 0 66 0 98 feet Same height equally distributed ER wiring Making connec
6. ption 3 Operation temperature 4 Detection distance 5 Display resolution 6 Detecting error 7 Detecting rate DC 10V 16V lt AW 35 C 70 C 1 15 8 00 feet 0 01feet 0 06 feet 4 times sec How to use P1405 display unit Sound Alarm Zone Indication Reverse BACKING SYSTEMS Distance Display Direction Indication P 1405 Display Reverse BACKING SYSTEMS P 1407 Display e Power The system is automatically activated when the reverse gear is engaged Self testing program will be done right after the system is powered on After the buzzer beeped and the direction indicators on the system is ready e Display 1 28 Distance between sensor and obstacle FS Indicate the closest obstacle direction using flashing LED or icon a EJ 0 ge Indicate zone stage with a pointer or car icon e Volume Adjustment There are two volume levels The switch is on the back cover of display unit e Precautions Danger zone start 2 feet away from obstacle Reverse speed should be less than 3 miles hour to avoid accidents and give you a chance to respond to backup sensor Thin and small obstacles can be detected at shorter range only e Sensing Range and Warning Method Distance Display 1 15 or Green Yellow Red light Light light Zone Indication 4 P Sound Alarm No Sound with Sound with Rapid Continuous Sound Long Intermit Short Intermit Sound
7. tions with assistant tools Make sure the recessed sensor surface facing upwards slightly while keeping the whole sensor body horizontally Test To check if the parking assistance system works properly 2 Vertical level 2 The surface to install sensors need to be vertical and flat 3 Direction of sensor Wire Connection Connect the red wire of controller to the reversing light s positive and the black to the negative The wiring card usage refers to the following diagram Note The E shape contact must be fully pressed e Precaution during installation 1 Do not scratch the surface of bump during drilling holes 2 Do not cut or damage the wire in any circumstance 3 Make sure the power cable is connected correctly The controller should be secured in a water proof location 4 The surface to mount the display must be clean e Troublehooting 5 Make sure all the connection is correct before final testing Any problem could refer to the Trouble Possible Causes shooting section No display a No power Make sure all the during b Display unit is not connection 1s reversing connected to correct e Final testing controller properly Wrong The sensor s position is wrong Change sensors 1 Use one selected object to test the sensing distance and orientation position warning as stated in page 7 indication 2 Use one selected object to check if each sensor is in Constantly An object within 0 89foot is
Download Pdf Manuals
Related Search