Important Safety Instructions
Contents
1. 2 Each time the SLOW button is pressed the speed of slow motion playback changes in the following sequence SF 1 2 SF 1 3 SF 1 4 Tae 1 PLAY lt SF 1 7 lt SF 1 6 3 Press PLAY to resume normal playback Changing chapter track While the disc is playing press the CH button to go immediately to the next or previous chapter or to the next or previous track Zoom 1 While a disc is playing press ZOOM until you reach the zoom size you want The ZOOM button toggles through 2x 3x 4x and then zooms out to 1 2x 1 3x and 1 4x then returns to normal playback 2 Move from one area to another pan using the arrow buttons 3 To turn ZOOM off press ZOOM until you get to the ZOOM OFF option Types of menus e Disc menu The appearance and contents of this menu varies according to the type of disc you have inserted It is separate from the Setup menu Info menu The unit s Info menu appears at the top of the screen while the disc is playing Press INFO on the remote to switch the Info menu on or off ae 1 10 Setup menu Press SETUP to access menu 1 16 00 13 07 this General Setup 11 The Info Menu ak Notes When you press STOP the unit stores the point where playback was interrupted If you press PLAY again playback resumes from this point To stop playback completely or to start again from the beginning press STOP twice If the unit is left in STOP mode for m2. Do not use its full capacity CD Rs should be preferably used instead of CD RWs rewritable CDs as in certain cases CD RW playback may be faulty Use reliable good quality CD write software Close all other applications on the computer to ensure reliable CD R disc recording 20 The Info Menu Audio DVD Some discs have several audio tracks used for different languages or different audio formats To change the language or audio format during playback 1 Press the INFO button twice 2 Use the left right arrow buttons to select the Audio icon or press the AUDIO button on the remote control 3 Choose a language or an audio format with the up down arrow buttons This option is only available if the disc offers dialog languages or audio formats When you change the dialog language using the Info menu it only changes the dialog language of the disc being played When you eject the disc or switch off the unit the language will revert to the one you selected in the language Setup menu Subtitles DVD Subtitles are turned off by default Turn on subtitles as follows 1 While the disc is playing press INFO twice then select the Subtitles icon using the left right arrow buttons 2 Select a language using the up down arrow buttons 3 To turn subtitles off select the off option or press SUBTITLE on the remote When you change the language of the subtitles using the Info menu it only applies to the disc
3. AM loopterminal and the other wire is inserted into the ground loop terminal Connecting to your TV VIDEO Method 1 Composite video jack yellow e The basic video jack is color coded yellow e Video cable yellow is supplied forthe connection for good picture quality Connect the video OUT jack on the receiver to the Video IN jack on your TV so the video content goes from the receiver to the screen VIDEO IN VIDEO IN Video cable supplied Rear of the unit Ventilation You must adequately ventilate the product Make sure there is adequate space around the unit to provide proper air flow for ventilation See diagram SSS Se f 7em t Zom This product complies with DHHS Rules 21 CFR Subchapter J Applicable at the date of manufacture For your safety The AC power plug is polarized one blade is wider than the other and only fits into AC power outlets one way If the plug won t go into the outlet completely turn the plug over and try to insert it the other way g KP S DA If it still won t fit contact a qualified electrician to change the outlet or use a different one Do not attempt to bypass this safety feature Removing the power plug is the only way to completely remove power from your product Make sure the power plug remains easily accessibl
4. Only use attachments accessories specified by the manufacturer e Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the a cart apparatus combination to Portable Cart Warning avoid injury from tip over e Unplug this apparatus during lightning storms or when unused for long periods of time e Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as the power cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Speaker wires are color coded to match the terminals Connect the speaker wire from the back of each speaker to the corresponding color terminal at the back of the unit Press down the tab to open the terminal and insert the wire Release the tab to lock wire in the terminal e When connecting the speakers make sure the polarities speaker wire to on the receiver For example red wire to red terminal on the receiver of speaker wires and terminals match If the cords are reversed the sound will be distorted Do not let the speaker wires touch each other it will damage the Home Theater s amplifier e Center speaker provided with this unit are magnetically shielded to protect your TV set
5. Radio frequencies will be browsed and radio stations stored automatically When all the available radio stations are stored or all 30 memory locations are full the auto preset programming function will stop Manual preset 1 Tune to a radio station see Manual tuning for details 2 Press MEMORY While the Program Preset number is still flashing input your desired preset number using the numeric buttons then press MEMORY to store it Retrieving preset stations 1 Press TUNER to enter the Tuner mode 2 Press CH to search up or down for the preset stations or directly press the numeric buttons S Tips e When the FM station broadcasts Stereo sound is found ST is displayed When you manually tune into a weak FM station press AUDIO on remote control to switch from Stereo to Mono mode This will reduce the background noise Gi e If there is any interference change the antenna s position until ideal sound reception is obtained TV and other electronic devices could be the cause of interference so try to position the antenna away from them e A weak signal can affect the Automatic preset programming function s efficiency Adjust the antenna for better reception and a more efficient search AUDIO IN AUX IN OPTICAL IN TV VCR or Set Top Box can be connected to AUX IN OPTICAL IN input jacks at the back of the unit or AUDIO IN at the front panel so that sound from the auxiliary component c
6. the TV e Replace the HDMI cable with a better one Bad HDMI cable can cause data lost Press HDMI key on remote handset several times to toggle among different HD OUTPUT The picture is of poor quality with snow or lines Check the connections There is no sound or the sound is of poor quality Check the connections Make sure the speakers are connected Make sure the MUTE function is not on No surround sound Check the speaker configuration in the Setup menu See Positioning speaker or Audio Setup I can t find my file in the jpeg listing e Make sure the file name is valid The remote control does not work or works only intermittently e Check that batteries are inserted or change them Aim the remote control at the unit The infrared beam must not be blocked or interrupted Check that the remote control is configured to control the device you are trying to operate with it The subtitles do not appear Check that the DVD disc provides subtitles Refer to the section on how to display sub titles The disc menu language is not the correct one e The disc menu language has not been set up e The language of your choice is not available on the disc Precautions Use e If your unit has been stored in a cool place for any length of time during a journey for example wait for about 2 hours before using it e The openings located on the top and bottom are for ventilation and must not be obstructed During
7. thunderstorms we recommend that you isolate the unit from the electrical supply so that it is not damaged by electrical or electromagnetic surges e This unit is designed for continuous use Switching off the unit to standby mode does not disconnect it from the mains supply To completely isolate the equipment remove the plug from the mains jack as some components remain connected to the electrical supply If you notice any burning or smoke disconnect the unit immediately to avoid any risk of electrocution Do not attempt to look inside the unit through the disk tray opening or any other opening You may be electrocuted or exposed to laser radiation 19 Limited Warranty All warranties implied by state law including the implied warranties of merchantability and fitness for a particular purpose are expressly limited to the duration of the limited warranties set forth above With the exception of any warranties implied by state law as hereby limited the foregoing warranty is exclusive and in lieu of all other warranties guarantees agreements and similar obligations of manufacturer or seller with respect to the repair or replacement of any parts In no event shall AVC be liable for consequential or incidental damages No person agent distributor dealer or company is authorized to change modify or extend the terms of these warranties in any manner whatsoever The time within action must be commenced to enforce any obligation o
8. to the unit s settings will be reverted back to the original settings IMPORTANT Once Progressive Scan has been activated an image will only be visible on a progressive scan TV or monitor If you choose this option and you don t have a progressive scan TV or monitor you may get a picture with incorrect color or no color LANGUAGE SETUP With this menu you can set the language for unit menus dialog subtitles and the disc menus If you chose English during initial set up any menus generated by the disc are in English and so is the language of the dialogs if this language is available on the disc om Language Setup 1 Select the Language Setup icon in the main menu using the left right arrow buttons 2 Select one of the options using the up down arrow buttons 3 Press the right arrow button to move to the language choices 4 Use the up down arrow buttons to highlight the language of your choice and press OK Player Menu Select the language of player menus and press OK Audio Select the dialog language using up down arrow buttons and press OK To change the Audio language during playback press INFO twice for DVD and use the left right arrow buttons to highlight the Audio icon Press the up down arrow buttons or AUDIO on the remote control to select audio language 17 Additional Information Jpeg files CD R and CD RW with jpeg files Certain jpeg files in cluding progressive jpeg
9. up down buttons repeatedly to display DVD Chapter elapsed time Chapter remaining time Title elapsed time and Title remaining time Audio CD Track elapsed time track remaining time disc elapsed time disc remaining time To directly access a location on the disc which does not correspond to the start of a title or chapter press INFO once and press OK highlight the Time Display icon using the arrow buttons then enter a time with the number buttons hh mm ss and press OK ae Note Time display function may not be available on all discs 2 6 During the slide show you can use the left right button to rotate the picture the up arrow but ton to rotate the image vertically the down arrow button to rotate the image horizontally Use the ZOOM button to magnify the picture Use the CH button to go back to the previous picture or the CH button to go to the next one and the STOP button to interrupt the slide show and display the disc s contents 7 When the unit has played all the files the music or slide show stops and the disc s contents are displayed again 8 Press STOP to end playback ak S Notes e The time taken for the contents of the disc to be displayed varies according to the size and number of jpeg files on the disc If nothing is displayed after a few minutes the file sizes may be too large Reduce the files resolution and write another disc e Before inserting a disc make sure it is c
10. It is not recommended to place the front speakers surround speakers and subwoofer near the TV set Cente Speaker Purple Gray Front Speakers Subwoofer Rear Speakers Surround Sound To adjust each speaker volume level for optimum listening experience 1 Press the LEVEL button on the remote control to select FL front Left speaker 2 Press the VOL VOL buttons to adjust the value up or down between 10dB and 10cB 3 Repeat step 1 and 2 for the other speakers FR SL SR CT SW Speaker gains may be set to levels of up to 10dB actual max levels may also depend on your Volume Setting Positioning speakers 3 2 6E HF A gilt Courtesy Dolby Laboratories 7 Playing Discs Basic Functions Compatible discs e DVD DVD R DVD RW DVD R DVD RW e CD CD R CD RW Compatible formats e DVD JPEG e CD VCD Regional coding Your unit has been designed to process regional management information stored on DVD discs The regional code for your unit is 1 Discs that have a different regional code will not play Operating the DVD receiver 1 Turn on your television set 2 Press ON OFF on the remote or ON STANDBY located on the unit s front panel Press DVD on the remote control Loading disc 1 Press amp on the front panel to open the disc tray 2 Place a disc onto the
11. USER MANUAL RTD317W It s important to read this instruction prior to using your new product for the first time Important Safety Instructions Additional safety information e Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus Always leave sufficient space around the product for ventilation Do not place product in or on a bed rug in a bookcase or cabinet that may prevent air flow through vent openings Do not place lighted candles cigarettes cigars etc on the product Connect power cord only to AC power source as marked on the product Care should be taken so that objects do not fall into the product Do not attempt to disassemble the cabinet This product does not contain customer serviceable components Connections and Setup Accessories provided Left and right front speakers Remote control and 2 AAA batteries One Pig Tail antenna wire Things to consider before you connect Ensure that the mains supply in your house complies with that indicated on the identification sticker located on the back of your unit Install your unit horizontally away from any source of heat fireplace or appliances creating strong magnetic or electric fields The components of this unit are sensitive to heat The maximum ambient temperature should not exceed 35 C 95 F Leave enough space around the unit to allow adequate ventila
12. authorized by Macrovision Corporation and is intended for home use only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited Important Safety Instructions Please read and save for future reference Some of the following information may not apply to your particular product however as with any electronic product precautions should be observed during handling and use e Read these instructions e Keep these instructions e Heed all warnings e Follow all instructions e Do not use this apparatus near water e Clean only with a dry cloth e Do not block any ventilation openings Install in accordance with the manufacturer s instructions e Do not install near any heat sources such as radiators heat registers stoves or other apparatus Including amplifiers that produce heat e Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your wall outlet consult an electrician for replacement of the obsolete outlet 23 Connections and Setup Connecting the speakers e Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus e
13. cal order on the right side of the screen 3 Select a folder using the up down arrow buttons on the remote then press the left arrow button to move to the music picture icons at the bottom of the screen Use the left right arrow buttons to select either music or picture mode 4 Press the up arrow button to move to the file list on the right side of the screen Use the up down arrow buttons to select a file Press OK or PLAY to start playback 5 The unit starts the slide show with the jpeg file you have selected then displays all the jpeg files in the same folder then all the jpeg files in the subfolders located in the same folder You can set the amount of time a picture remians on the screen in the General Setup menu Additional Information e This unit is for domestic use only and must not be used for industrial purposes e Total or partial copying of recordings protected by copyright legislation without the explicit permission of the holder of the rights contravenes current legislation Copying or downloading music files for sale or any other business purpose constitutes or could constitute a violation of copyright law Cleaning Use a soft dry clean cloth Regularly dust the vents at the back or sides Using solvents abrasive or alcohol based products risks damaging the unit If an object or liquid enters inside the unit unplug it immediately and have it checked by an authorized servicer or service center Hand
14. currently being played When you eject the disc and switch off the unit the subtitles will default to the subtitle language you selected in the Languages menu This function may not be available on all discs The Setup Menu There are four options in the main setup menu General Setup Language Setup Audio Setup and Video Setup Press SETUP to bring up the main menu Select one of the menu icons across the top of the screen using the left right arrow buttons The menu s options are displayed on the left side of the screen Press the right arrow button to move to the option s choices on the right Press SETUP if you want to exit setup GENERAL SETUP General Setup Video Progressive Function provides high quality pictures with less flickering Turn on Progressive Scan if you used the Component Video jacks of the unit to connect a TV or monitor compatible with a progressive scan signal Select P Scan YPbPr and press OK to activate Progressive Scan HDMI Setup This lets you select the resolution of the player s output according to the connected TV Supported HD JPEG mode 480p 720p 1080i and 1080p TV Type Depending on the format of the DVD disc you can choose the picture format aspect ratio best suited to the format of your TV screen 4 3 PS reproduces a 4 3 picture without distortion 4 3 LB gives best reproduction of pictures recorded in this format i e with horizontal bands at the top and bottom of the sc
15. disc tray with the label side up 3 Press amp again to close the disc tray Playback Switch the unit and the TV set on 1 After loading a disc playback starts automatically or the disc menu appears If the disc menu appears select the Play option to begin playback 2 Press STOP to stop playback Accelerated play While the disc is playing press REV or FWD one or more times to vary the speed and direction of the accelerated play Press PLAY to resume normal playback Pause While the discis playing press PAUSE once for freeze frame Press PLAY to resume normal playback Frame advance 1 Press PAUSE twice Step is displayed 2 Each time you press PAUSE button the picture advances one frame 3 Press PLAY to resume normal playback 1 Left Right Front Speakers Front speakers carry primarily music and sound effects Center In surround mode the center speaker carries most of the dialog as well as music and effects It should be set between the left and right peakers Surround Rear Speakers The surround speakers overall sound balance should be as close as possible to the front peakers Proper placement is vital to establish an evenly distributed sound field 4 Subwoofer A subwoofer is designed to reproduce powerful low bass effects explosions the rumble of spaceships etc N Ww Basic Playback Operations Variable slow motion 1 Press SLOW button on the remote in play mode
16. e Note This DVD player is designed and manufactured to respond to the Region Management Information If the Region number of a DVD disc does not correspond to the Region number of this DVD player this player cannot play the disc The Region number for this DVD player is Region 1 Method 2 Component video jacks Pr Pb Y e The component video jacks are color coded green blue and red Additional component video cables not supplied are required to provide best picture quality They are usually color coded green blue and red Connect the component video OUT jacks on the receiver to the component video IN jacks on your TV so the video content goes from the receiver to the screen Component video cable not supplied Rear of the unit XS e If your television is a high definition television use the unit s progressive scan output to get the highest possible video resolution Set the Progressive Scan option in the Video menu to On e Ifoneofthedevicesis not working checkthat all the cables have been inserted properly into the jacks e Connecting mono components to your receiver If your component has only one output for audio mono connect it to the white audio jack on the receiver and don t use the cable s red plugs 5 Overview of Controls ON OFF Turns on off the unit DVD Selects the DVD mode TUNER Selects the TUNER and selects between FM AM AUDIO AUX Selects and toggles be
17. f AVC arising under the warranty or under any statute or law of the United States or any state thereof is hereby limited to one year from the date of purchase This limitation does not apply to implied warranties arising under state law This warranty gives you specific legal rights and you may also have other rights which may vary from state to state Some states do not allow limitation on how long an implied warranty lasts when an action may be brought or the exclusion or limitation of incidental or consequential damages so the above provisions may not apply to you For more information on other products and services please contact our web site at www RCAav com Important Also keep your Bill of Sale as proof of purchase Model NO oacatcaissecicscisduvaswdneciccastecustuteshodecencesiutecbidusih detuswes TYPE Of it Ramee ener cra ener en een mmr een Per re eee Sial Os cactenccate a E Date purchased sse sssssssseeeeessssssseesessssssssrerossssserreesssseseeesss INVOICE NO serr nee eaae ieai Dealer NaMe snssessenoesseeseesesssesressroserseoneosresurosesenseonrosersernsosress FOR SERVICE AND REPAIR PLEASE VISIT www RCAav com Specifications and external appearance are subject to change without notice Print in China 811 317W91W010
18. f the rear speakers Rear Right Rear Left Adding the subwoofer channel to the 5 channels for bass sounds counted as 0 1 channel results in 5 1 channels or 6 Channels that bring you the most sophisticated Dolby Digital sound enjoyment Technical Specifications Amplifier Section RMS Output Power Dolby Digital Mode with 10 Total Harmonic Distortion Rear Channels 32 Watts channel 1kH 40 Front and Center Channel 32 Watts per channel 1kHz 40 Subwoofer Channel 40 Watts 100Hz 30 Total RMS Output Power Dolby Digital mode 200 Watts Muting Attenuation 70 dB Frequency Response 200Hz 20KHz 3dB 1KHz ref Subwoofer Frequency Response 20Hz 200Hz 3cB 100HZ ref Signal to Noise Ratio 70 dB Dolby Digital AM Tuner Section Frequency Response 2kHz 3dB 400HZ ref Usable Sensitivity 3000uV m S N 20dB Signal to Noise 38dB IF Rejection 35dB FM Tuner Section Frequency Response 15kHz 3dB 1kHz ref Quieting 24dB Signal to Noise 62dB stereo 65dB mono IF Rejection 70dB Dimensions Hx Wx D mm Unit 66 x 430 x 240 Front Speakers 214 x 78 x 69 Center Speaker 290 5 x 78 x 69 Rear Speakers 214 x 78 x 69 Subwoofer 312 5 x 155 x 273 5 21 The Info Menu Creating a Program List for Program Play Mode Audio CDs and DVD discs To use program play mode you must first create a program list 1 To create a program list press the INFO button twice for CD and three t
19. files cannot be read by this unit When composing your title use 10 characters or less no spaces and avoid the use of special characters including The total number of files and folders on the disc should be less than 650 Make sure that files have the jpg extension Files without the jpg extension will not be able to be read by the unit even thought the files are shown as jpeg images on your computer Sound Enhancement Systems This receiver is equipped with several built in sound enhancement systems Manufactured under license from Dolby Laboratories DE DOLBY Dolby Pro Logic and DIGITAL the double D symbol are trademarks of Dolby Laboratories Dolby Pro Logic The Pro Logic mode uses the built in circuit to steer the Left Center Right and Mono Surround channel audio signals and uses all five speakers to play both stereo and Dolby Pro Logic program source such as TV and VCR You can use this mode with any stereo program source such as VCR TV to enjoy multi channel sound experience Dolby Digital The Dolby Digital mode lets you enjoy full digital surround from software processed in the Dolby Digital format Dolby Digital provides better sound quality and a more powerful presence than conventional Dolby Surround This unit is equipped with Dolby Digital 5 1 channel so that you can enjoy enhanced full digital surround sound The new system provides stereo separation o
20. imes for DVD Highlight the Play Mode option and press the up arrow to select the Program option 2 Press OK The Program screen is displayed 3 The first spot in the list is highlighted Use the number buttons on the remote to enter a track number As for DVD discs T stands for Title while C stands for Chapter As for Audio CDs T stands for Track 4 Use the arrow buttons to move to the next spot in the list Enter the next track number 5 Continue entering tracks until you have completed your list 6 Highlight the Play option at the bottom of the screen and press OK or press PLAY to start playback The program list will play in the order you programmed it To stop program play press STOP or select Standard from the Play Mode option in the INFO display If you want to cancel the list repeat Steps 1 and 2 to select CLEAR and press OK Sleep 1 Press INFO twice for CD and three times for DVD Select Sleep icon with the left right arrow buttons 2 Select one of the available options using the OK button Off 30 60 90 or 120 minutes ase Note This function is not available AUX IN OPTICAL IN AUDIO IN TUNER mode Introscan CD This option plays the first ten seconds of each track on a CD 1 Press the INFO button twice then select the Play mode icon with the left right arrow buttons 2 Press the up down arrow buttons to select the INTRO option and press OK to start IntroScan 3 Press STOP to stop In
21. is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This Home Theater has earned the ENERGY STAR Connections and Setup Where the mains plug or an appliance coupler is used as a disconnect device the disconnect device shall remain readily operable Other important use and cleaning information at the end of the booklet Connecting the antennas um 752 A CO GND The AM and FM antennas connect to the AM and FM terminals on the system s back panel They must be hooked up in order to receive clear reception AM Loop Antenna 1 Uncoil the AM Antenna wire 2 Press down on the Antennas tab to open the terminal 3 Make surethewhite wire onthe AMloopantenna isinsertedintothe
22. jack on the front panel of the unit to the headphone output on mp3 players Notes e 3 5mm to 3 5mm audio cables not included Press either SOURCE on the main unit or AUDIO AUX on the remote control to select AUDIO IN mode Press the SURROUND button on the remote control to select the sound mode wily e Suggest using 3 5mm AUDIO NE IN jack for MP3 player and AUX IN jacks for auxiliary equipment such as DVD VCR or PC If the AUX IN or AUDIO IN audio signal is mono you may not receive audio on all speakers Using remote control to navigate through the on screen menus Use gt lt v and OK on the remote control to navigate through the on screen displays the DVD player s menu the Info Display that appears during playback or a disc s menu Use gt lt v on the remote to move through on screen menus in the direction of the arrow button e g to move right press gt The arrow buttons are used to highlight an option Once highlighted press OK to select the option that is highlighted Q Note x Insert 2 AAA UM 4 R03 batteries to the remote control prior to use Overview of Controls Front Panel Controls Toggles between different subwoofer output levels among Starts pauses soft balance strong powerful Switches the Adjusts the unit on and playing a disc volume off AUDIO IN jack connects audio devices Opens and closes the disc tray Stop
23. ling and caring for discs e Handle your discs with care Hold the disc with your fingers at the edges or through the hole Insert the disc with the label facing up for a single sided disc Place the disc properly into the tray in the allotted holder Use a soft cloth to clean discs if necessary always wiping from the centre to the edge Always put discs back in their cases after use and store in a vertical position Do not close the tray with two discs in it or with a disc not sitting correctly in the holder Do not play cracked chipped or warped discs nor try to repair them with adhesive tape or glue Do not write on a disc Do not move the unit when a disc is being played Do not scratch discs or store them in places exposed to direct sunlight high humidity or high temperatures Do not use aerosol cleaners benzene anti static liquids or any other solvent for cleaning discs When cleaning wipe gently with a soft damp water only cloth from the centre to the edge avoiding circular motions which could cause scratches and interference during playback Title chapter DVD track audio CD To directly access a title chapter DVD or a track audio CD press INFO press OK Select the Title TT Track TRK or Chapter CH icon and enter a number directly with the numeric buttons Press OK again to confirm XS Note Many discs only have one title Time display To access the Time Display press INFO on the remote Press the
24. n hazardous radiation exposure Do not open covers and do not repair yourself Refer servicing to qualified persionnel Visible and invisible laser radiation when open and interlocks defeated DO NOT STARE INTO BEAM Class 1 laser product CLASS 1 LASER PRODUCT APPAREIL LASER DE CLASSE 1 PRODUCTO LASER DE CLASE 1 Illustrations contained in this document are for representation only Connections and Setup Connecting to your TV via HDMI input HDMI stands for High Definition Multimedia Interface HDMI transfers digital audio and uncompressed digital video on a single cable Press the HDMI button on the remote control to change output signals as follows 480p 720p 1080i and 1080p HDMI cable not supplied Rear of the unit Note Refer to the owner s manual of the connected TV as well Getting sound from external sources such as TV Using AUX IN jacks 1 Connect the AUX IN jacks from the unit to the AUDIO OUT jacks on VCR TV Set Top Box or other component 2 Push the AUDIO AUX button on the remote control to activate the sound from the external source 3 Push the SURROUND button on the remote control to select the sound mode Audio cable 2 not supplied Rear of the unit Overview of Controls SURROUND Changes the Surround sound setting Press the button to select between 5 1 Channel and Stereo modes Remote control functi
25. omes into the unit and out through the speakers Connecting auxiliary components Refer to Getting sound from external sources such as TV for details on connecting the auxiliary components to the unit Selecting AUDIO IN AUX IN OPTICAL IN mode Press either SOURCE on the main unit or AUDIO AUX OPTICAL on the remote control to select AUDIO IN AUX IN or OPTICAL IN mode Sound output in AUX IN mode or AUDIO IN OPTICAL IN mode e You may change the surround setting by pressing SURROUND to select between 5 1 CHANNEL and Stereo modes If the AUX IN or AUDIO IN OPTICAL IN audio signal is mono you may not receive audio on all speakers 15 Additional Information Troubleshooting The unit does not switch on e Make sure it is plugged in Press the ON OFF button on the remote control or the ON STANDBY button on the front of the unit The device switches off spontaneously e The device switches off automatically when it is in STOP mode for more than 30 minutes without any user intervention Switch it on again It might be impossible to read the disc Insert the disc with the printed side facing up Check that the disc can actually be played by this device Check that the disc s regional code matches the unit s regional code This unit s regional code is 1 Clean the disc There is no picture e Check you have switched on the TV set Check the connections Select the AV input assigned to the unit on
26. ompatible with the unit 16 Compatible Formats In order to ensure playback discs must conform with DVD or CD standards This unit may not play some recordings or files due to differences in recording formats software used and disc types DVD Video Digital video discs 12 cm single or double sided single or dual layer DVDs are high density optical discs on which high quality picture and audio are recorded by means of digital signals VIDEO DVD R DVD RW DVD R DVD RW Most DVD R and DVD R one recording only DVD RW and DVD RW discs rewritable depending on the DVD writer and discs used Recordings using DVD R and DVD RW discs must be made in Video DVD mode Recordings using DVD RW discs must be made in accordance with the specifications for DVD RW discs with a 4 7 GB capacity Audio CDs Audio CDs 12 cm CD R CD RW Most CD R one recording only and CD RW discs rewritable CD Rs written during a multisession recording can be played provided that the session has ended before the disc is played depending on the write software However depending on the condition of the CD writer computer and the disc used you may find that not all discs will play When playing a CD R disc it is normal for the unit to take up to 60 seconds to recognize the disc before starting to play If the disc is not recognized after a period of 120 seconds remove the disc and insert it again
27. ons in tuner mode TUNER Selects the TUNER and switch between FM AM VOL Adjusts the sound volume MUTE Mutes and restores the sound TUNER Tunes down and up the radio frequencies MEMORY Stores a station CH Selects programmed stations AUDIO Selects between Stereo and Mono mode for Tuner FM Please respect the environment and prevailing regulations Before you dispose of batteries or accumulators ask your dealer whether they are subject to special recycling and if they will accept them for disposal This class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la class B est conforme la norme du NMB 003 CUE ENECEF WARNING To reduce the risk of fire or electric shock hazard do not expose this product to rain or moisture The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases should be placed on the apparatus Digital optical input 1 Connect components capable of outputting Dolby Digital e g TV or Set Top Box or standard PCM CD format digital signals 2 Push the OPTICAL button on the remote control to activate the sound from the external source 3 Push the SURROUND button on the remote control to select the sound mode Set Top Box Optical digital audio cable not supplied Rear of the unit Using AUDIO IN jack Connect the 3 5mm AUDIO IN
28. oper manner according to your state provincial and local regulations D Battery shall not be exposed to excessive heat such as sunshine fire or the like g KEZ H Center speaker Composite Video Cable Left and right Surround Speakers Subwoofer One external AM loop antenna e Thehumidity ofthe room should not exceed 75 Ifyou have to use the unit outdoors do not expose it to rain or splashing water The apparatus should not be exposed to dripping or splashing and no objects filled with liquids such as vases should be placed on the apparatus Moving the unit from a cold place to a warm one can cause condensation on some components inside the unit Let the condensation disappear on its own before turning the unit on again Before moving the unit make sure the disc tray is empty 4 Aiming Aim surround speakers straight across the room not down at viewers to help create a more open spacious surround sound field Alternative Surround Placement Rear wall If rear wall mounting is the only choice aim the speakers at each other A towards the front B or towards the sidewalls C D Experiment with placement until sounds seem to surround you rather than come from behind you No adjacent walls Surround speakers can go on stands facing each other to approximate sidewall mounting A or to the sides or rear of the viewing area aimed upwards they can go right on the floor or preferabl
29. ore than 5 minutes without any user interaction a screen saver is activated At the end of 30 minutes without any user interaction the unit switches off automatically INVALID KEY will be displayed if the function you select is not available Gi The Info Menu 1 Press INFO on the remote while a disc is playing to display the info menu The first banner shows title chapter and time display information 2 Press INFO again for audio language subtitles and camera angle 3 Press INFO a third time for play mode bookmark and sleep timer 4 Use the right left arrow buttons on the remote to select an icon 5 Use the up down buttons to scroll through the options DVD Info Display Title Chapter Time display Za 1 10 1 16 00 13 07 Audio language Subtitles Camera angle 1 3ENG DA 5 1CH Play mode Bookmark Sleep timer PLAYMODE BOOKMARK SLEEP CD Info Display Track Time display CD TRK 1 10 00 13 07 Play mode Bookmark Sleep timer PLAYMODE BOOKMARK SLEEP Jpeg Files Playing jpeg files Jpeg files are image files Make sure that they have a resolution of less than 2 megapixels 1 Open the disc tray 2 Place the disc with the printed side facing up and close the disc tray The folders on the disc will be listed in numerical order on the left side of the screen When you highlight a folder then press OK button The list of songs or pictures in the folder are listed in numeri
30. ou ll hear a test tone come from the speaker you select Use the VOL button to adjust the level to your desired setting Press OK button to exit this function VIDEO SETUP 1 Select the Video icon in the main menu using the left right arrow buttons 2 Select a menu option using the up down arrow buttons and press OK E Video Setup Slide Time The Slide Time option lets you select the amount of time a picture is displayed in a slide show The choices are 5 seconds 10 seconds or 15 seconds 18 Limited Warranty AVC MULTIMEDIA AVC makes the following limited warranty These limited warranties extend to the original consumer purchaser and is limited to non commercial user of the product One Year Parts amp Labor Warranty AVC products purchased in the United States are warranted to be free from defects in materials or workmanship for a period of one year from the date of their original retail purchase If the unit fails to conform to this warranty we will service the product using new or refurbished parts and products at AVC s sole discretion During a period of one year from the effective warranty date AVC will provide when needed service labor to repair a manufacturing defect at its designated Service Center To obtain warranty service in the United States you must first call our Customer Support Center at 1 800 506 5746 or 1 877 252 6873 during the hours listed in the box below The deternination of service
31. press SUBTITLE on the remote control Otherwise the subtitle language indicated on the disc is selected AUDIO SETUP You can adapt your unit to other equipment and access specific functions with the Audio Setup menu 1 Select the Audio Setup icon in the main menu using the left right arrow buttons 2 Select an option using the up down arrow but tons Press the right arrow to move to the op tion s choices Audio Setup Night Mode You can use this function to control the different sound levels via dynamic compression It improves the quality of the sound track at a low volume and quiets the loudest sounds You can choose between Quiet Moderate or Off Center Delay Rear Delay Basic settings have been preset forthe speakers included with your unit However to suit the acoustic conditions in your listening room and to make the sound more effective you may need to delay the signal coming from some of the speakers Channel delay compensates for centre or surround speakers thatare closer tothe listening position than the front speakers 1 Highlight the Center Delay Rear Delay option using the up down arrow buttons 2 Press the right button to move to the default distance 3 Press the up down buttons to adjust the distance Test Tone This function is used to test and adjust the volume level gain for each individual speaker channel Use v to select the speaker channel you wish to test and adjust Y
32. random playback on CDDA disc REPEAT Accesses the repeat function LEVEL Toggles channels for different level settings ius Adjusts the value using VOL 9 z FCC Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN DO NOT EXPOSE TO RAIN OR MOISTURE NE PAS EXPOSER LA PLUIE NI L HUMIDIT WARNING SHOCK HAZARD DO NOT OPEN AVIS RISQUE DE CHOC LECTRIQUENE PAS OUVRIR THE LIGHTNING FLASH AND ARROWHEAD WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF DANGEROUS VOLTAGE INSIDE THE PRODUCT THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF IMPORTANT INSTRUCTIONS ACCOMPANYING THE PRODUCT WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USERSER VICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL CAUTION USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE WARNING MAINS PLUG IS USED AS DISCONNECT DEVICE AND IT SHOULD REMAIN READILY OPERABLE DURING INTENDED USE IN ORDER TO DISCONNECT THE APPARATUS FROM MAINS COMPLETELY THE MAINS PLUG SHOULD BE DISCONNECTED FROM THE MAINS SOCKET OUTLET COMPLETELY Caution This product utilizes a laser Use of controls or adjustments or performance of procedures other than those specified may result i
33. reen or in 16 9 16 9 widescreen reproduces 16 9 format films in full on a 16x9 screen Camera angle DVD Some discs offer different camera angles for specific scenes 1 To change the camera angle press the ANGLE button on the remote or press the INFO button twice and select the Camera angle icon with the left right buttons 2 Choose the angle with the up down arrow buttons If the disc was recorded using a single camera angle this function is not available Play mode all discs except jpeg 1 While the disc is playing press the INFO button twice for CD and three times for DVD 2 Select the Play Mode icon using the left right arrow buttons 3 Use the up down arrow buttons to select an option DVD play modes standard program A B repeat title repeat chapter repeat Program play mode is only available if a program list has been created see below Repeat mode is only available with discs that display elapsed time and remaining time To repeat a sequence between points A and B choose the A B repeat option and then follow the instructions for entering the two points Audio CD play modes standard introscan random program repeat A B repeat disc repeat track 4 To stop repeat playback select the Play Mode icon and use the up down arrow buttons to choose the Standard option Default This option allows you to return the unit s settings to the original factory settings Any changes you have made
34. s disc Selects the input sources Press playback repeatedly to select e DVD to watch DVD videos e TUNER to listen to the radio e AUX IN rear AUDIO IN front to listen to the audio input from the connected TV VCR or Set Top Box e OPTICAL rear to connect digital audio components 10 Important Information Service information This product should be serviced only by those specially trained in appropriate servicing techniques Important battery information e Do not mix different types of batteries or new and old batteries Do not use rechargeable batteries e Inorderto avoid any risk of explosion observe the polarities indicated inside the battery compartment Replace only with the type of batteries specified Do not dispose of them in a fire or recharge them If you are not using the remote control for a long period of time remove the batteries DVD copy protection In accordance with the DVD standard your DVD player is equipped with a Copy Protection system which can be switched on and off by the DVD disc itself in order to make any recording of the relevant DVD disc onto a videotape of very poor picture quality or even impossible This product incorporates copyright protection technology that is protected by method claims of certain U S patents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of this copyright protection technology must be
35. tion 10 cm 4 inches on either side and above the top and 5 cm 2 inches at the rear Connections and Setup Front speaker placement For best results follow the speaker placement below Alignment Align the center speaker evenly with A or slightly behind B the left and right speakers but not ahead of them Angle Place the left and right speakers to form a 45 degree angle with your favorite viewing position to duplicate the soundtrack mixer s perspective Height The three front speakers should be as close as possible to the same height This often requires placing the center speaker directly on top A or beneath B the TV set Better surround placement Location If possible place surround speakers to either side of the listening area not behind it Height If space permits install surround speakers 2 3 feet above viewers This helps to minimize localization effects If your product operates on batteries adhere to the following precautions A Any battery may leak electrolyte if mixed with a different battery type if inserted incorrectly or if all batteries are not replaced at the same time B Any battery mayleak electrolyte or explode if disposed of in fire or an attempt is made to charge a battery not intended to be recharged C Discardleaky batteriesimmediately Leaking batteries can cause skin burns or other personal injury When discarding batteries be sure to dispose of theminthe pr
36. troscan and press PLAY to resume normal playback Bookmark DVD and audio CD 1 Press INFO twice for CD and three times for DVD Select the Bookmark icon with the left right buttons and press OK A menu is displayed with five bookmarks 2 The first bookmark space is highlighted Press OK to set the bookmark The bookmark is saved and is indicated by the number 1 You can set up to five bookmarks on a disc 3 To start playback from a bookmark press the PLAY button on the remote 4 To delete a bookmark highlight it and press CLEAR Note This function is only available with discs whose elapsed time or remaining time appears in the Info menu Gi STA The Setup Menu Subtitles Select the subtitle language using up down arrow buttons and press OK To change the language of the subtitles during playback press INFO twice for DVD and use the left right arrow buttons to highlight the Subtitle icon Press the up down arrow buttons or the SUBTITLE button on the remote to select a subtitle language Disc Menu To change the language of the disc menus select the language using the up down arrow buttons and press OK The language you select will only be displayed if the disc is programmed with that language Notes e If the selected language is not available on a disc the disc s language will be used instead e If the language chosen is available it is automatically selected when you display the subtitles or
37. tween the front AUDIO IN mode and rear AUX IN mode for listening to audio input from connected TV VCR or SetTop BOX OPTICAL Selects OPTICAL IN at rear for digital audio connection 0 9 Number entry CLEAR Quits the current setting manually from the TV screen without saving change INFO Accesses the Info menu TITLE Accesses the title menu of DVD discs DISC MENU Accesses the disc menu during playback OK Confirms your selection gt lt alv To navigate through the menus The left and right arrows also tune the radio frequency in the tuner mode MUTE Mutes and restores the sound SETUP Enters Setup menu RETURN In DVD mode returns to the previous menu VOL Adjusts the sound volume CH gt 1 CH 1 lt lt Directly accesses the next or previous chapter DVD or track CD Selects programmed stations in TUNER mode REV Starts reverse accelerated play PLAY Starts playing a disc FWD Starts forward accelerated play SLOW Selects SLOW motion function STOP Stops playback PAUSE Freezes frame accesses frame advance AUDIO Accesses the audio function ANGLE Accesses the camera angle function for DVD disc ZOOM Accesses the Zoom function SUBTITLE Selects the subtitle languages or turns subtitle off if available HDMI Changes video output signals 480p 720p 1080i or1080p SUBWOOFER Selects among subwoofer output levels soft balance strong powerful RANDOM Turns on off
38. ved or changed Out of Warranty In the event your product requires repair after the limited warranty period has expired please contact our Customer Support Center at 1 800 506 5746 1 877 252 6873 or www RCAav com Hours Monday Thursday 9am 7pm Friday 9am 5pm Saturday 9am NOON Eastern time Important You are responsible for any transportation shipping or insurance relative to the return of the product to our Product Returns Center 22 Radio The unit has a built in tuner that allows for FM radio function The AM loop antenna allows for AM radio function Manual tuning 1 Connect the FM antenna and the AM loop antenna at the back of the unit 2 Press TUNER 3 Tune a station by pressing TUNER repeatedly until the desired station is found Alternatively you can press and hold the same buttons down for about one second to activate the automatic search function In this mode the unit will automatically tune frequencies until it finds a station 4 Repeat step 3 to tune to another radio station 5 Press TUNER to toggle between FM and AM Storing radio stations The unit can store up to 30 radio stations in its memory You can enter every single radio station yourself or the unit can store all available radio stations automatically in ascending order Automatic preset programming 1 Press TUNER to enter the Tuner mode 2 Press and hold TUNER for two seconds to start automatic preset programming 3
39. will be made by AVC customer support PLEASE DO NOT RETURN YOUR UNIT TO AVC WITHOUT PRIOR AUTHORIZATION New or remanufactured replacements for defective parts or products will be used for repairs by AVC at its designated Service Center for one year from the defective warranty date Such replacement parts or products are warranted for an additional one year from the date of repair or replacement The Customer will be required to ship the unit to the Service Center indicated at the time Customer Support is contacted to make the necessary repairs The customer is responsible for all transportation charges to the service facility Packaging and Shipping Instruction When you send the product to the AVC service facility you must use the original carton box and packing material or an equivalent as designated by AVC Your Responsibility 1 You must retain your bill of sale to provide proof of purchase 2 These warranties are effective only if the product is purchased and operated in the U S A or Canada 3 Warranties extend only to defects in material or workmanship and do not extend to any product or parts which have been lost or discarded or damage to product or parts caused by misuse accident improper operation or maintenance or use in violation of instructions provided with the product or to product which has been altered or modified without authorization of AVC or to products or parts thereof which have had the serial number remo
40. y a few feet off the floor such as on end tables B A c ue lt T B D E IE e a a e Test tone Channel balance Channel balance Your receiver is equipped with a test signal generator for balancing the channels As the signal travels from channel to channel adjust the level controls until each channel plays at the same loudness level Level adjustment and surround channel level expectation Even though you adjust the surround channel to be as loud as the others on the test signal on actual program material the surround channel is adjust the surround level program producers use surround for subtle atmospherics and ambience and only rarely for special effects 8 FCC Information This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there
Download Pdf Manuals
Related Search