User Manual
Contents
1. ccccccccccccccocosoccces 37 5 ee OW eaivcrc see esce scenes eves sec AE EE E EENE ER 38 GREENTEL Simplifying Wireless M2M Announcements Thank user for choosing our product GREENTEL MX100 and MX101 are wireless broadband HSUPA H 264 MJPEG Network Cameras GREENTEL MX100 and MX101 built in HSUPA cellular module wireless upload speed up to 5 76Mbps Please read this manual carefully before using the product Important Safety Information This product is not intended for use in the following circumstances e Area s where radio transmission equipment such as cell phone are not permitted e Hospitals health care facilities and area s where cell phones are restricted by law e Gas stations fuel storage and places where chemical are stored e Chemical plants or places with potential explosion hazard e Any metal surface that may weaken the radio signal level e The appliance is intended to be installed in restricted access location Only service person or authorized person is allowed to access Copyright Announcement Copyright GREENTEL LIMITED 2010 All rights reserved Reproduction transfer distribution or storage of part or all of the contents in this document in any form without the prior written permission of GREENTEL is prohibited Information Edition GL A MX100 1 0 GREENTEL Simplifying Wireless M2M WEEE Notice The Directive on Waste Electrical and Electronic Equipment WEEE which entered2. DONS password FO DDS server address C DOHS server port 8080 ists WEE mapping port feo Update interval S 60 Mote When UFHF is OH the web map port and web port should be the same Check Start DDNS and then select a DDNS supplier input the DDNS user name DDNS password DDNS server address and DDNS server port user apply set local mapping port and update interval and then click OK Type a domain name in the address field of the Internet Explorer If user can access the device properly it means that the domain name is redirected successfully FTP Parameters FTP Parameters FTP usernarce 888888 FTP password FRITT FTP host IP 192 168 1 40 FTP host port 21 Start FTP uploading change FTP Host IP address in order to open FTP Server and then click OK After user start the FTP server set its IP address and ftp directory and enable the services Set alarm linkage to upload snapshot and video recording through FTP and trigger the alarm or start timing snapshot and upload to FTP then the pictures and recordings will be uploaded to specified directory of the computer 2 e GREENTEL Simplifying Wireless M2M UPNP UPHF OPNE On UPNP data Web port y state Unmapped gt Data transfer port y State Unmapped o Data control port fo t state Unmapped gt gt 1 Remote transfer port y tate Unmapped gt Data control port Data transfer port 1 Remote transfer port Data transf
3. 192 168 1 1 Ping Interwal s 30 Ping Package Length Byte i 024 Ping failure times s 20 Link Mode select WCDMA Tel Numbers input the WCDMA dial up telephone number provided by the mobile network opeartor Username input the user name provided by the mobile network operator Password input the password provided by the mobile network operator APN Name input the APN provided by the mobile network operator Authentication Type select form Auto PAP CHAP None LCP echo interval set length time for the interval of link detection LCP echo failure set the maximum number of trials for link detection failure MRU set the maximum receiving unit MTU set the maximum transmission unit Connection Mode currently it only support always online mode Network Select Type select from Auto 2G 3G Radio Band Set select or multi select from GSM 850 GSM 900 GSM 1800 GSM 1900 WCDMA 850 WCDMA 900 WCDMA 1900 WCDMA 2100 Band saving select from enable disable enable stands for enable IP head compression Get DNS from operator select from enable disable enable stands for use the DT GREENTEL Simplifying Wireless M2M DNS allocate by the mobile operator Ping Link Detection select from enable disable enable stands for enable ICMP Ping link detection to remote server Ping IP Address ICMP Ping IP address Ping Interval set length time for the interval of ICMP Ping detection Ping Pac
4. into force as European law on 13th February 2003 resulted in a major change in the treatment of electrical equipment at end of life The purpose of this Directive is as a first priority the prevention of WEEE and in addition to promote the reuse recycling and other forms of recovery of such wastes SO as to reduce disposal The WEEE logo shown at the left on the product or on its box indicates that this product must not be disposed of or dumped with userr other household waste User are liable to dispose of all userr electronic or electrical waste equipment by relocating over to the specified collection point for recycling of such hazardous waste Isolated collection and proper recovery of userr electronic and electrical waste equipment at the time of disposal will allow us to help conserving natural resources Moreover proper recycling of the electronic and electrical waste equipment will ensure safety of human health and environment For more information about electronic and electrical waste equipment disposal recovery and collection points please contact userr local city centre household waste disposal service shop from where user purchased the equipment or manufacturer of the equipment GREENTEL Simplifying Wireless M2M 1 Camera Introduction GREENTEL MX100 is a wireless broadband HSUPA PTZ H 264 MJPEG Network Camera GREENTEL MX101 is a wireless broadband HSUPA Fixed H 264 MJPEG Network Camera GREENTEL MX100 and MX101
5. 00 42 7F WEB port Booo Data transfer port 3000 1 65533 Alarm host address foooo gt gt gt Alarm host port 8000 o Remote host address M000 gt Remote host port 3004 gt Multicast address 235111 _ Range 225 0 0 0 239 255 255 255 Multicast port so Range 6000 9999 Mote Any changes of network parameters will take effect after saved and system restarted Connection type gt DHCP Basic Network 3G Channels Alarm Server IP address amp port Connection type WAC address 02 F 2 00 00 42 7F WEB port Booo Data transfer port c 1 655533 larm host address foooo larm host port 8000 gt Remote host address foooo Remote host port 3004 gt Multicast address 235 114 Range 225 0 0 0 239 255 255 255 Multicast port s0 Range 6000 9999 Note Any changes of network parameters will take effect after saved and system restarted DHCP is disabled by default User should reboot the device after DHCP is enabled Connect the Web camera and PC to a DHCP enabled router The router will assign a IP address for example if the IP address of the router is 192 168 0 1 the IP address of the Web camera will be 192 168 0 100 after sae GREENTEL Simplifying Wireless M2M DHCP is enabled which is within the same network segment with the router to the Web camera automatically DDNS DDS Start DDNS E DOHS supplier Defaut DONS f Dorain rare FO DONS user nare
6. 4 MX101 Back Panels GREENTEL Simplifying Wireless M2M 2 5 Interface from up to down 2 6 LED indicators System indicators g Red error running well Red indicator Green card via 3G Ethernet Interface indicators Yellow indicator On On A normal 100M connection is through this port no data packets are transmitting Blinking On A normal 100M connection is through this port data packets are transmitting On Off A normal 10M connection is through this port no data packets are transmitting Blinking Off A normal 10M connection is through this port data packets are transmitting GREENTEL Simplifying Wireless M2M 3 Application Introduction and System Requirement MX100 can be installed at any place without fixed line internet access and with 3G networks coverage Thanks for its high upload speed up to 5 76 MHz via 3G HSUPA networks which can enable high quality real time video streaming Ca System requirement The 3G SIM Card should have fixed public IP e Or dymanic public IP with DDNS e Or any kind of IP and using fixed public IP broadcasing server with RealView software GREENTEL Simplifying Wireless M2M 4 Accessing the Camera 4 1 Search IP and PC configuration Search MX100 s IP via Search IPVS software x _ server name Dew Type IP mac Web Port Data Port Channel video server SERVER 192 165 1 19 02 F2 00 00 42 7F g Pleas
7. 544 in NTSC system X is 0 672 and Y is 0 448 ape GREENTEL Simplifying Wireless M2M Video coding Video Coding Server end storage strearn Resolution 4CIF D1 Network Transfer Strearn M Incoming Guide Data Resolution 4CIF D1 M s Bite Rate Type Constant gt l Bite Rate Type Constant gt C Max Bite Rate so 32 4000 Max Bite Rate gt 1500 s Quality Upper Limit 2 p31 32 4000Kbps C SR E B par Quality Upper Limit 2 Frame Fate 25 1 30 Quality Lower Limit 31 2 31 Mote Please select based on the l Video amp Audio i aa Te ae a stream Type video amp Audio is adjustable Hote Save and reboot is a raust after change Eey Frame Interval i OO H 264 Frame Hate 25 Strean Type video amp Auc Key Frame Interval ion Compression H264 l Check the option Incoming Guide Data and then select a set value to display Compression Resolution Bite Rate Type Quality Lower Limit and Frame Rate or user can leave this option unchecked and set the above parameters on the right directly Available resolutions are CIF PAL 352X288 Half D1 PAL 704X288 Di PAL 704X576 Average bite rate of the image should be kept the same when the bite rate has been set up and the average bite rate of the image should be changed according to the complexity of the image when the quality has been set up Different levels of quality are not distinguishabl
8. Wireless M2M Resolution D1 Half D1 CIF QCIF Video Stream Bit rate Range 32K to 4Mbps H 264 Image Settings Brightness Contrast Saturation Hue Exposal control AES 1 60 1 50 to 1 120000 S AGC AWB BLC Privacy mask Motion Detection Video H REV Support horizontal reverse Video V REV Support vertical reverse Audio Compression G 711 Audio Stream Two way audio broadcast Audio Input Output Mic input headphone output 1 2 Technical Specifications Hardware CPU HI3512 FLASH 8M DRAM 128M O S Linux HSUPA HSDPA UMTS WCDMA 850 900 1900 2100 MHz HSUPA up to 7 2Mbps downlink 5 76Mbps uplink HSDPA up to 7 2Mbps downlink 384Kbps uplink UMTS up to 384Kbps downlink 384Kbps uplink Antenna plug SMA SIM card 3V 1 8V Ethernet RJ45 10 100Mbps Power supply DC 12V GPIO terminal block for 1 D I 1 D O RS485 PTZ control Audio Mic input headphone output Dimension H x W x D 134 x 124 x 136mm MX100 Dimension H x W x D 133 x 65 x 55mm MX101 Weight 1KG Operating temperature O C to 45 C Operating humidity 20 to 85 1 3 Product Kit HSUPA IP Camera AC DC Adapter External 3G Antenna GPIO Connector Ethernet Cable RJ45 CD GREENTEL Simplifying Wireless M2M 2 Hardware Introduction 2 1 MX100 Front Panels J g 749 Lens sm W 9 oa Infrared Leds IP Camera 2 2 MX100 Back Panels GREENTEL Simplifying Wireless M2M 2 3 MX101 Front Panels Lens 2
9. built in HSUPA cellular module wireless upload speed up to 5 76Mbps Applications such as in the CAR CAMPING BOAT BABY CARE and SHOW 1 1 Features Access IP Camera via 3G HSUPA HSUPA upload speed up to 5 76Mbps enable real time high quality video streaming H 264 MJEPG Codec for resolution WEB configuration for setup or remote monitoring e Multi levels password for protection from web Two way audio via G 711 audio compression external audio input output Supports RTSP VLC PS TS Stream Media protocol Alarm triggered by GPIO motion detection date time video lost e File upload via FTP Email notification via Email SMS Local storage to SD card e Supports TCP IP UDP ICMP DHCP NTP DNS DDNS SMTP FTP HTTP PPPoE UPnP RTP RTSP RTCP Free management software supports up to 100 channels e Video broadcast software enables video broadcast to either private or public IP e SDK available for application development and system integration Camera e Image sensor 1 3 SONY CCD 420 520 TVL e Built in infrared LEDs up to 16ft 5m for night vision MX100 only e Day Night Auto Lens CS mount 8mm f 2 0 angle of view horizontal 42 e Minimum Illumination 0 5 Lux F1 2 5600K Pan 0 to 355 Tilt 0 to 90 Speed 15 s MX100 only Auto IRIS Support Scan System Interlace Video Audio e Video Compression H 264 MJPEG Frame Rate 1 to 30 f s GREENTEL Simplifying
10. 00 11 Server end snapshot parameters FTP scheduled record End Time 00 H 00 M End Time 00 H 00 M End Time 00 H 00 mM End Time 00 H 00 M End Time 00 H 00 mM End Time 00 H 00 Mm End Time 00 H 00 mM Y Server end timing to snapshot End Time 00 H 00 MI End Time 00 H 00 MI End Time 00 H 00 Mm End Time 00 H 00 MI End Time 00 H 00 M End Time 00 H 00 M End Time 00 H 00 M Y Server end snapshot parameters Snapshot image quality fan 1 100 snapshot image format 4CIF D1 34 GREENTEL Simplifying Wireless M2M Set JPEG snapshot image quality the snapshot image format is D1 by default Pictures stored in the server end storage device and those uploaded to FTP will be taken with those settings Server end storage device w Server end storage device Disk Mo Disk type Total capacity Free capacity Format Ho remote storage device Click Format and then click OK in the pop up dialog box to start formatting the device will reboot automatically after finish formatting successfully 34 172 GREENTEL Simplifying Wireless M2M Appendix A Port Introduction Following ports are using during video transmission on the Internet TCP 80 WEB port 3000 Data transmission starting port 3001 Data control port IP camera must follow the port mapping operation of these three ports above so as to be accessed from p
11. Audio Talkback Snapshot Record E Relay on off lris S lris Preset N fa Ny i z 2s GREENTEL Simplifying Wireless M2M Network modes TCP or MultiCast users can select according to their needs Play real time video Click n button real time video from all channels will play in the preview window Stop video playing Click ETE button the preview window will stop playing real time video from all channels Audio Click EZ button the button icon will become orange Microphone input connect the microphone to the audio in interface and speak to the microphone If user access it and enable audio on the computer user will be able to hear speech and realize inputting audio from the microphone To set audio parameters please click Settings gt Channel gt Audio Parameters Network Character superposition Video Coding PTZ Protocol Adjust color Y Area Shield Sido Pararneters Audio input settings udio in type hic Tlie Boost Qf 2 d Audio output settings udio out volume 100 0 100 Select Mic for audio in type when Mic Boost is on the sound of audio will be amplified Line in The audio in port of the Web camera can be connected to the audio out interface of the computer with audio cable If user access it from another computer and enable audio user will be able to hear the music that the computer is
12. CAMERA ccccccccccccccc000000000000000000000000000000000000000000000000 11 4 1 SEARCH IP AND PC CONFIGURATION csccccccsecccccccccccsecccccscecccaucccescececeeeccscuececeusecceeuaeseess 11 ce E AVARA ACPA R 24050 2920210242 00 29002A0G24 2000000200191029 1170 2000 20001G22090 12 4 3 REALTIME oecon ne eoa Ee R C drosc eS eedabiabsceiiae EE E E aa a a ieni 12 4 4 REPLAY ecccicccicicccececccccssccsccsseosesesoosussscoesreosssscssosaneroesssouesenessenesessussteuesuesesesantosesesensauesesensnoesunsnensas 15 4 5 TING ea escenario sateen strona E dae uaa T ARRO AAA 2AAA AL DAE VASU CARA ACA AAA 16 4 5 1 SETTINGS gt BASIC pianoaren a a ACMRA OaE a EE ERA DR E bad CRR E 17 4 5 2 SETTINGS gt NETWORK ssacececocadestaccceanaaccaenseasaceansanaesateaneseraconshsabsasaciapsoascaatausadantaanaGentaanecacnsa 19 4 5 3 SETTINGS gt 3GL cccccccccccccccccccccceccccccceccccecocccccocccccssscccssoscccsssoccsssooecssoooceensocenanoneeens 22 4 5 4 e NES ae 1 E 26 4 5 5 SETTINGS gt ALARM ccciscccccscicsosisicccsstssossetssososossssssnsssssscsaposssssstsnsssesrsosasesosssrscsssestssnasesessarenous 30 4 5 6 SETTINGS gt SERVER STORAGE ccsccccsesscccssseccccssccccseccesescccesscccecesscususescuesesensussseueescecs 33 APPENDIX A PORT INTRODUCTION c ccccccccccoccccccoo0osooocco0u0000osooeoouu0escess 36 APPENDIX B GPIO TERMINAL APPLICATION
13. GREENTEL Simplifying Wireless M2M GREENTEL HSUPA PTZ Network Camera and HSUPA Fixed Network Camera User Manual For MX100 and MX101 GREENTEL Simplifying Wireless M2M ANNOUNCEMENTS c cccccccccccccccccoooeecc0000000000000000000000000000000000000000000000000000000000000000000000 3 1 CAMERA INTRODUCTION ccccccccccococccccco0000eeeocc00000eeoccu000seeeccceuseececeues 5 ELFPO A0 774 10 00022A E 1020670140720020 700 5 1 2 TECHNICAL SPECIFICATIONS cccccccccssecccccucecccccusceccccueucecccaecececcuuseeececcuucececcuauceseeeuaeeesecens 6 L PRODUCT JT TE 252020 022352540202420A22020BeP22029R 004260 saauaecousssmmccateceananessaneaoaaseoskasuca te entenaiuetansetsaniesuaeentats 6 2 HARDWARE INTRODUCTION cccccccccccocccccco00osecocc000000eecco00000eeooeouuuueseses 7 2 1 MA IOO FRONT PANELS sieisen 3232004566550255 5632 6242020002450432 NAAL 00000A sez C0 2 02A0G TO 7 2 2 MXT00 BACK PANELS aecaieaii a 7 2 3 MXITOLIFRONT PANELS cnrs E EEE Eai 8 2 4 MX101 BACK PANELS 2 ccccccccccsecccccccscccceccusccccccusececcccuueeccceuucececcuucecccecauceseceuacsececuuausess 8 2 5 INTERFACE FROM UP TO DOWN sessciccehaveecassuesicaecuscacedsenracesbetcarciubeeneadvesanseecatagectiabenctisusytestanieecs 9 2 OLED INDICATORS ee oE a e BENE DA 2 eA 00 E a A 9 3 APPLICATION INTRODUCTION AND SYSTEM REQUIREMENT c000 10 4 ACCESSING THE
14. art Time foo H00 M Start Time 00 H 00 M Start Time 00 H 00 M Start Time 00 HOO M Start Time 00 H 00 M Triggering Sms D F 230 Y Camera Been Shaded Alarm Trigger schedule Settings End Time 00 H 00 mi End Time 00 H 00 m End Time 00 H 00 14 End Time 00 H 00 Mm End Time 00 H 00 14 End Time 00 H 00 14 End Time 00 H 00 mM GREENTEL Simplifying Wireless M2M Email Alarm Settings Y Ermal Alarm Settings Send Ernall if there are alarm Ott Pronty User nare Ivlal server IP senders nare Recerver s nare 1 Recerers name 2 Recerver s name 3 FO Password C FO I lai server port 25 o 0 semai 0 Rece wversemalll i i sS SCS S 0 Receiversemal2 ss S 0 Recever semal3 First install a mail server such as CMailServer within the LAN network and then add an account If server end snapshot is not enabled for motion detection and sensor alarm the mailbox of the receipt will also receive an alarm mail with title and text only no pictures 4 5 6 Settings gt Server Storage server N Server end timing to record FTP scheduled record Server end timing to snapshot Y Server end snapshot parameters Y Server end storage device Server end timing to snapshot Start timing recording P Server end timing to record clase Start Time 00 H 00 Mi End Time 00 H 00 Mm close gt gt amp S
15. chedule Settings Camera Been Shaded Alarm Trigger schedule Settings Y Emal Alarm Settings 30 GREENTEL Simplifying Wireless M2M Sensor Detection Schedule Settings Y Sensor Detection Schedule Settings Start Sensor Detection Sensor Harme Sensor close gt SY Start Time 00 H 00 m close k Start Time 00 H 00 m close gt e Start Time 00 H 00 M close gt gt n Start Time 00 H 00 M cose n Start Time 00 H 00 m close n Start Time 00 H 00 m cose n Start Time 00 H 00 m Start server end recording while alarming Upload the alarm recording to FTP P Start server end snapshot Upload the alarm snapshot to FTP P Trggenng alarm output a Triggering Sms a End Time 00 H 00 M End Time 00 H 00 M End Time 00 H 00 Mm End Time 00 H 00 1 End Time 00 H 00 M End Time 00 H 00 M End Time 00 H 00 M Under the mode of Normal Open user need to trigger the alarm short connect the alarm input interface with the ground wire Under the mode of Normal Close the Web camera will be on alarm all the time It will stop alarming as user trigger the alarm short connect the alarm input interface with the ground wire Start the trigger channel and the snapshots will be kept in front end storage device Motion detection vlotion Detection Area Settings sIf sensibility Adjusting 85 Select full screen Clear all GREENTEL Simplifying Wireles
16. e Time Setting 1 Click Save after changing the parameters to rake sure the parameters be saved when device start up next time 2 Wost of the parameters will work after you click OF Sorne of thern need to save and reboot first Attention to the note User Management Timing to reboot Restore to leave factory default parameters System update 4 5 1 Settings gt Basic Basic Y Device Hame Y Time Setting User lvlaragerrnent Y Trung to reboot w Restore to leave factory default parameters Y System update Device Name Input the name of the device and then click OK User can also modify the name of the device Device Hame Device Hame video Server Seral Humber S000E1 0020129950 Time Setting Select from Synchronization with PC system synchronization with NTP server Time Setting Time synchronization type Current PC Time 2010 09 19 1425 52 Sunday 17 GREENTEL Simplifying Wireless M2M User Management User lvlanagerrnent dran User Hare 888888 Admin User Purd 009999 gt gt gt Verity ws i i Cormon User Hamel 1 C oraraon User Pwd feo Verity le Cormon User Hamed 2 1 Conmrmon User Puc Very lr Mote Username can only be composed by munbers letters and symbols Ordinary users have no parameter setting permissions Admin user could view the real time video also modify camera parameter settings Common user could o
17. e After changing the resolution user should reboot the device to activate the new resolution PTZ feature MX100 only the RS485 interface of the device is used to connect a high speed dome with PTZ Click PTZ Protocol to expand settings page under it as shown below PTS Protocol PT Address i Baudrate 600 S Data Bit f Stop Bit M Check Bit None FTZ Protocol PFELOC D Update PTZ Protocol P Select Frotocol ptz Browse 252 7 72 GREENTEL Simplifying Wireless M2M Tick off Update PTZ Protocol click the button Browse to select the PTZ protocol to be updated and then click OK to update it Set PTZ Address Baudrate Data Bit Stop Position and Check Bit in compliance with that of the PTZ These can be copied to use in all channels or one of the channels except PTZ address Enter the page of Real time Monitoring and then operate the PTZ function buttons as shown below Operate UP Down Left Right buttons of the PTZ the dome can rotate accordingly Adjust PTZ speed and then control the rotating of the PTZ the dome can rotate at the speed that user set Click Zoom Zoom button to zoom in or zoom out the focus of the image Click Preset button to set the preset point Input the number of the preset point and then click Call button to call the preset point 28 GREENTEL Simplifying Wireless M2M Image adjusting Click the line Adjust brightness a
18. e configure userr Ethernet connection as follow then PC s IP should be in the same network segment such as 192 168 1 1 Internet Protocol TCP IP Properties x General ou can get P settings assigned automatically If your network supports this capability Otherwise You need to ask your network administrator for the appropriate IF settings Obtain an P address automatically Use the following P address IF address 192 168 1 1 Subnet mask 255 255 255 O Default gateway l l C Obtain DNS server address automatically f Use the following ONS server addresses Preferred DNS server l Alternate DHS server Advanced 11 2 GREENTEL Simplifying Wireless M2M 4 2 Login Open Internet Explorer only support IE at this moment enter the IP address 92 168 1 19 default IP of of router in the URL link field e g MX100 Mote 1 If your screen appears BLAME when you click the Ire video link click here 2 Works only with Internet Explore 6 0 4 3 Real time After login user will see Real time windows 2 IP CAMERA Microsoft Internet Explorer File Edit view Favorites Tools Help Q ex ka lt B 2 A Jo Search Se Favorites Ol NEE Address http 192 168 1 19fen_contentfadwc asp IP CAMERA 4 EJ a pE If your screen appears BLANK when you click the live vider link click here TCP C Multicast JB
19. er portt2 Mote If the gateway router dont support UPMP or UPNP is OFF the port will not be able to mapping If the UPMP of the router is ON and the state of the port above is still OFF please check the router settings if the port have been used If there are more than one device connect to the same gateway the port of each device shouldn t be the same to avoid the port conflict Connect the device to a UPNP enabled router Web port data transfer port data control port and remote transfer port of the device will be mapped State displays Mapped Streaming Protocol Y Streaming Protocol RTSP Enable RTSP Listen port 554 VLC M Enable VLC Destination address 1 927 168 1 1 Destination port 1 234 Enable or disable RTSP VLC 4 5 3 Settings gt 3G 3G Dial up settings 34 5 network Dial log 34 status PIN Code Y SIS Settings VY GREENTEL Simplifying Wireless M2M Dial up settings Y Dial up settings Link Mode WCDMA Tel Numbers PRBE gt Usermamie l Password APH Marne 3GNET sits Authencation Type auto n LCF echo interval hoo LCP echo failure 20 8 MRU 1500 MTU 800 Connection IvyIode Always Online gt Metwork Select Type Auto n Radio Band Set M GSM 250 M GSM 900 M GSM 1200 M GSM 1900 IY WCDMA 850 M WCDMA 900 M WCDMA 1900 M WCDMA 2100 Band saving Enable Get dns from operator Enable Ping Link Detection Enable Ping IP Address
20. he local computer in the image format of Bmp The image file will be named in the following method device name time Video Server_15_51 _43 Bmp for example Size of the image file is in accordance with the resolution of the interface If the preview image has overlaying characters and time display the captured picture will also have overlaying characters and time display Local recording Click button the button icon will become orange and the system will start recording The system will automatically create a folder named by the current date recorded in Disk D of the local computer and save the recorded file to the folder in the format of 264 The recorded file will be named in the following method IP address channel number time For example the file recorded on Sep 18 2010 will be saved as d 20100918 192 168 1 19_ 1 155327 264 If Disk D is out of space the recorded file will be saved to the next Disk automatically If the disk has insufficient space the earliest recorded files will be deleted and new data cover earliest recorded automatically Click Record button again to stop recording and the button icon becomes white 4 4 Replay In this page user could reply the video stored in local PC or server Select Local PC storage follow windows will appear F Local PC storage Server storage Query date 2010 v Sm 19D From Ou Om To 23H 59 M File list File name Mo recordi
21. kage Length ICMP Ping package length Ping Failure times set maximum number of trials when ICMP detection fails 3G network 3G network status including 3G Status 3G IP Subnet Mask Default Gateway Primary DNS Address Secondary DNS Address 3G network 34 Status Disconnected SC LP 0 0 0 0 subnet Wask 0 0 0 0 Default Gateway 0 0 0 0 Primary DMS Address 0 0 0 0 secondary DMS address 0 0 0 0 Dial log Dial log Beginning Dialing up 99 Connect script failed Beginning Dialing up 99 Connect script failed Beginning Dialing up 99 Connect script failed Beginning Dialing up 99 Connect script failed Beginning Dialing up 99 8 Connect script failed ey ae GREENTEL Simplifying Wireless M2M 3G Status 3G status including Operator Current Network Signal Strength IMEI SIM State 30 status Operator OPERATOR Current Network EDGE Signal Strength IMIEI SIMI state SiM not exist PIN Code Input the PIN code to unlock the SIM Card if it is required by mobile operator PIN Code PIN protection Disable PIN code 1234 SMS Settings Input the mobile phone number to receive dial up IP address after enable Send ip address via SMS when 3G dial up successfully connected Note Because after choosing 3G 3G camera will use 3G network to connect to Internet Unless you have fix IP from operator which you will k
22. ly please login again the device will reboot automatically 4 5 2 Settings gt Network Network IP address amp port DDNS FTF Parameters UPHP Strearung Protocol IP address amp port Connection type gt Static IP address Channels Alarm Server IP address amp port Connection type Static IP address IP address 192 168 1 19 Gateway 192 168 1 1 Subnet mask 255 255 2550 O O O DM mono MAC address O2 F2 00 00 42 7F WEE port Booo Data transfer port Boo o o 1 655533 Alarm host address M000 Alarm host port Booo Remote host address M000 Remote host port 3004 gt Multicast address 235 111 _ Ra nge 225 0 0 0 239 255 255 255 Multicast port lso Range 6000 9999 Note 4157 changes of network parameters will take effect after saved and systera restarted 2 19 GREENTEL Simplifying Wireless M2M User can modify the IP Address Subnet Mask Gateway Web Port Data Transfer Port Remote Host Address Alarm Host Address amp Alarm Host Address Port Multicast Address amp Multicast Port and user can also turn on or turn off Web service port UPNP PPPOE service Click OK and then click Save button on the left and reboot the device to activate new settings Connection type gt PPPOE sic Network 3G Channels Alarm Server P address amp port Connection type ERE OL a eee PPPOE user name PPPOE password NAC address 02 F 2 00
23. nd color to expand settings page under it as shown below Adjust color Brightness 128 Range 0 255 Contrast soo Range 0 255 Saturation 150 Range 0 255 Hue 128 Range 0 255 Honzontal offset 8 Range 0 32 Vertical shift 0 Range 3 Adjust the parameters of brightness contrast saturation hue and horizontal offset Their ranges are as shown on the webpage Area shield rea Shield bral gt Clear braa Clear braz C Clear bad gt Clear Area Shield On off P Check the box Area Shield On off Press and hold the left button of user mouse and then drag user mouse within the preview image to select the range to be shielded The maximum size of each piece of area that can be shielded is a quarter of the image User can set up four pieces of shielded area at most 29 GREENTEL Simplifying Wireless M2M Click OK to save user work Clear the area shielding that has been set the areas will disappear after user click OK Audio Parameters Select the tab Audio Parameters to display settings for audio parameters under it Please refer to the above audio and talkback functions Audio Parameters Audio input settings udio in type hic w IvIic Boost Off 20db Audio output settings udio out volume 100 0 100 4 5 5 Settings gt Alarm Alarm Server Y Sensor Detection Schedule Settings Y vlotion Detection Area Settings Y Wlotion Detection S
24. ng at this period Sever storage search for the server SD card to take a snapshot 15 GREENTEL Simplifying Wireless M2M Real time Replay Settings Start time query M Fror 2010 v 9m 190 From OH OM To 2010 v 9 m 19D To 23 H 59 M J lt E EI Input the date and start time end time of the recording local and remote that user want to query click B button recording File List will display as query conditions Click the Play button behind a recording file historical recordings will play normally in preview window The preview window will stay at the last frame of the images after the recording ends Size of preview image clic SES at the sizes of 100 200 and full screen respectively The checked size buttons to play the preview image button will be represented with white background When playing in full screen user can click the right button of the mouse to restore to the original display size Image buffer iH Be SB to set the buffer level of the image to O 5 10 20 50 100 respectively The bigger number of buffer the more delay of video but video will be more smooth The checked buffer button will be represented with white background 4 5 Settings In this page user could set MX100 s parameters including Basic Network 3G 26s GREENTEL Simplifying Wireless M2M Channels Alarm and Server Basic Network 3G Channels Device Nam
25. nly view the real time video Timing to reboot Y Timing to reboot Timing to reboot Ott Reboot time 1 H 5 hil Input the reboot time and then click OK to reboot the Web camera at specified time Restore to leave factory default parameters w Restore to leave factory default parameters Mote Except the device name IP address and port all the rest parameters will be back to the leave factory default parameters The device will reboot automatically Restore Click Restore button and reboot the Web camera manually to restore the parameters to factory settings Device name and network parameters will not be restored 18 GREENTEL Simplifying Wireless M2M System Update System update Built in webpage version Webpage Version 707 00 06 03 Webpage Compile Time 2010 06 08 Software Version BSP Version gt WO6001004 gt gt gt BSP Compile Time 2010 06 09 gt gt Application Version gt WO6 O0 1004 OO Application Compile Time 2010 06 09 gt Note Keep the power supply and network connection no intermittence while updating If there are abnormal intermittence it will break the device It will reboot automatically after updating Select update file itr Browse Apply Cancel Click Browse button to select the itm file then click OK button to upgrade device firmware After finish upgrading the page will display The program has been updated successful
26. now the correct IP address Otherwise if Operator gives you Dynamic IP it will change every time you make connection To solve this issue you can click on Send internet address via SMS 3G Camera will send IP address which Operator assigns to you by SMS SIS Settings Days 3 1 23 Cell Phone Murnher 1 3408404471 Content SMIS center number C Send ip address via SMS when 3G dial up successfully conneted 25 lt GREENTEL Simplifying Wireless M2M 4 5 4 Settings gt 3G Channels Y Character superposition Y Video Coding PTZ Protocol Y Adjust color Y Area Shield budo Pararneters Character superposition Network 3G Channels A Y Character superposition Channel Name Channel gt Time type 2009 4 2014 55 10 Location X 8 y 60 Frame rate Notindicating gt Location X 8 10 Character 1 Location X 8 vefo Character2 Location X 8 Y 130 Input the characters to be displayed in video superposition User can set one line including lower case characters numbers and special characters and set the coordinate position to be displayed select a time type and set the coordinate position to be displayed choose a type of frame rate and set its coordinate position to be displayed and then click OK User can input up to 24 characters in the field of Character 1 it can display up to 30 characters Location of OSD superposition in PAL system X is 0 672 and Y is 0
27. playing and realize audio line in To set audio parameters please click Settings gt Channel gt Audio Parameters mice GREENTEL Simplifying Wireless M2M Network Character superposition Video Coding PTZ Protocol Adjust color Y Area Slueld udo Parameters Audio input settings udio in type Line in Line in volume 40 0 100 Audio output settings ndio out volumne 100 0 100 Select Line in for audio in type Volume is tunable 1 100 Note Line in is only available for devices that have line in interfaces Talkback Click KILE button the button icon will become orange Mic in interface of the computer is used to connect microphone its audio out interface is used to connect stereo system If user speak to the microphone the stereo system will play what user speak user can also connect the line in interface of the computer with the line out interface of the stereo system and the stereo system will play the music that the computer is playing Talkback can set the audio out volume of the Web camera as shown below Network Character superposition Video Coding PTS Protocol Adjust color Area Shield dudo Parameters Audio input settings Audio in type Line in Line in volume go 0 100 Audio output settings Sudio out volume 100 0 100 14 GREENTEL Simplifying Wireless M2M Snapshot Click button the current screen can be saved to C temp of t
28. s M2M Select a range and sensitivity for detection Sensitivity is 86 by default When the Web camera is not connected to video source and has OSD signals the pulse of OSD will also trigger motion detection alarm Click the line Motion Detection Schedule Settings to expand settings page under it as shown below Start motion detection vlotion Detection Schedule Settings clase gt Start Time 00 HOO m End Time 00 H 00 m cose gt s Start Time 00 HOO m End Time 00 H 00 m cese o s Start Time 00 H 00 m End Time 00 H 00 m cose n Start Time 00 a 00 m End Time 00 H 00 m cose gt s Start Time 00 H 00 11 End Time 00 H 00 Mm close n Start Time 00 H 00 m End Time 00 H 00 M cose gt Start Time 00 HOO m End Time 00 H 00 m Start server end recording while alarming Upload the alarm recording to FTP 7 Start server end snapshot Triggering alarm output 7 C Upload the alarm snapshot to FTP D Triggering Sms D Set the detection time and alarm linkage and then click OK Start the trigger channel and the snapshots will be kept in front end storage device Start linkage alarm snapshot and upload it to FTP The pictures are unloaded to specified root directory of the FTP server Camera Been Shaded Alarm Trigger Schedule Settings Start camera been shaded detection Triggering alarm output C sensibility Start Time foo H00 M Start Time foo Hoo M St
29. tart Time 00 H 00 Mi End Time 00 H 00 m close gt YS Start Time 00 H 00 mt End Time 00 H 00 m close gt Start Time 00 HOO mt End Time 00 H 00 m close gt YS Start Time 00 HOO mt End Time 00 H 00 m close gt gt SY Start Time 00 H 00 Mi End Time 00 H 00 Mm close gt gt s Start Time 00 H 00 Mi End Time 00 H 00 Mm 33 GREENTEL Simplifying Wireless M2M Check the box Start timing snapshot Set a snapshot time interval within the time range that has been set Web camera will take a Snapshot and save it to the server storage device at the time interval that user have set If Snapshot FTP Uploading has been enabled the snapshots taken will also be uploaded to the local root directory specified in the FTP server FTP schedule record Start FTP scheduled record D close gt n Start Time 00 H 00 M close gt gt n Start Time 00 H 00 M closes Start Time 00 H 00 m close Start Time 00 H 00 11 close Start Time 00 H 00 m close _ gt J Start Time 00 H 00 M close _ gt J Start Time 00 H 00 M FTP schedule record Snapshot time interval BOO 10 3600 Start timing snapshot FTP upload after snapshot P cosets Start Time 00 H 00 Mt dose gt gt gt Start Time 00 H 00 m cosets Start Time 00 H 00 Mt cose ssi Start Time 00 H 00 m close Start Time 00 H 00 M close Start Time 00 H 00 4 close Start Time 00 H
30. ublic network UDP transmission port is 3002 Multicast port is port number channel number 2 2 DE GREENTEL Simplifying Wireless M2M Appendix B GPIO Terminal Application The common connection method between alarm input of the IP camera and alarm siren G GMD Earthing GHD Power Power C A 3 M a JOJEISUNUUE Alarm siren has two working status always on or off The connection way is as picture above After connecting alarm siren choose corresponding probe mode Start probe alarm and set alarm time due to working status of alarm siren That s all to finish connection of alarm siren At this time alarm siren is awaiting orders of alarm 37 GREENTEL Simplifying Wireless M2M 5 Support In case users have problems with the installation and use please address them to the Technical Assistance Department by e mail support greentel eu com GREENTEL LIMITED WEB http www greentel eu com EMAIL info greentel eu com Copyright Greentel Limited 2001 2010 All rights reserved Subject to alterations without notice 38
Download Pdf Manuals
Related Search