TDA30XUSERENH_User_Manual_iD-Series 2015-03-13
Contents
1. S Z 4 for Mono Bridge operation min In this mode the channel 2 amplifier stage processes the identical input signal than channel 1 but with reversed phase The channel 2 input signal is not used ignored The loudspeaker load must then be connected between the two positive chan nel outputs pin 1 and pin 2 using a specially configured SPEAKON con nector cable This effectively doubles the maximum output voltage But please note that this also doubles the minimum allowed loudspeaker impedance Zn A WARNING In Mono Bridge Operation RMS output voltages can be as high as 230 V Wiring to the speaker loads must conform to NEC class 3 safety standards or its equivalent that meets all national and local electric codes All customer specific cables may only be manufactured by qualified suppliers personnel All cabling or rewiring work must be carried out by qualified personnel 4 Signal Processing Block Diagram Analog 1 PEQ 10x PEQ 10x PEQ 10x PEQ 10x Input DSP 1 Input Source Selection 0 1 Compressor Gain Pp VU Meter Peak Limiter ink Input DSP 2 Input Source Selection amp 1 Compressor Gain VU Meter Peak Limiter Input DSP 3 Input Source Selection amp 1 Compressor Gain VU Meter Peak Limiter Input DSP 4 Input Source Selection amp 1 Compressor Ga2. This area should be in line with the amplifier If this cannot be achieved a forced ventilation system has to be used Note that continous high power draw at low load impedance equal or less than approx 2 7 can drive the amplifier into thermal limitation So please check the amplifier temperatures on the display or in the DSPControl application and reduce the onput levels if necessary 3 5 Signal Inputs 3 5 1 Analog Input Pin 1 ground Pin 2 hot in phase Pin 3 cold out phase Always use symmetrical balanced shielded cable to connect the amplifier 3 5 2 AES Input The digital AES XLR input accepts any AES EBU signals pro or consumer format in 16 to 24 bit resolution and 44 1 48 88 2 or 96 kHz samplig fre quency This wide input frequency range of is guaranteed by an integrated sample rate converter SRC chip 3 6 Remote Control Network Input The Ethemet Link network connector allows you to access the iD4 iD7 from a host computer for remote control firmware update and downloading DSP presets The iD4 iD7 is configured by default to use DHCP for automatic IP address assignment in the network If not desired this feature can be set through the DSPOontrol application 3 7 Power Outputs 3 7 1 SPEAKON Connection Both SPEAKON connectors are connected to channel 1 and channel 2 out puts The pin configuration of the SPEAKON connectors is as follows e e Pint Channel B Output Pint
3. The left 4 MENU button always acts as an ESCAPE EXIT button in all menus 5 1 6 Rotary Encoder with Push Button The rotary encoder allows to make swift adjustments of parameters like for example the Gain settings by simply tuming it in the desired direction In some menus the push function of the encoder will act as an ENTER button for example when loading or saving presets or will allow you to access the parameters sub settings for the Low Pass High Pass PEQ Limiter and Com pressor 5 2 Hot Key Functions Standby To set the iD4 iD7 to standby mode simply press both 4 gt MENU buttons simultaneously for more than three seconds You will then be asked if you want to switch to Standy Mode Pressing the encoder knob without rotating it will then power down the main power supply of the jD4 iD7 The standby function can of course also be controlled by the DSPControl remote application 5 3 Standby Function The 104 107 offers the possibility to set the amplifier into standby mode either rom the user interface or by the DSPControl remote application n standby mode the iD4 iD7 will power down it s main SMPS thus saving energy while at the same time staying accessible through the network From the amplifier s user interface this function is accessible through a Hot Key unction as described above nside the DSPControl remote application you can access this function through he Unit menu An additional feature
4. 5 6 Main SMPS Protections 5 6 1 Over Current Protection 5 7 Fans 5 8 Filter Cleaning 6 Troubleshooting 6 1 Problem No reaction when switching the amplifier on 6 2 Problem No sound 6 3 Problem Error message Error Amp switched off 7 Specification 8 Typical Performance Diagrams y 120 W output power 2 load 8 1 Gain vs frequer 8 2 Gain vs frequency 120 W output power 4 O load 8 3 THD 1 KHz vs input level 2 load 8 4 THD 1 kHz vs input level O 4 load 8 5 THD vs frequency 120 W output power 2 load 8 6 THD vs frequency 120 W output power 4 load 8 7 Channel separation vs frequency 120 W 4 8 8 DIM100 vs input level 4 load 8 9 Common mode rejection ratio vs frequency 8 10 FFT of noise level vs frequency 8 11 Output impedance vs frequency 8 12 Damping factor into 8 vs frequency 9 Unit Conversion Equations and Lookup Table 9 1 Unit Conversion Equations 9 2 Lookup Table 21 21 21 21 21 21 22 22 22 22 22 22 22 22 22 23 24 24 24 24 25 28 28 28 28 28 29 29 29 29 30 30 30 30 31 31 31 10 Warranty Information 10 1 Summary of Warranty 10 2 Items Excluded from This Warranty 10 3 What CAMCO Will Do 10 4 How to Obtain Warranty Service 10 5 CAMCO Product Improvement 11 Service Information 12 Maintenance Information 13 Decommissioning Company information Changes Made to The Amplifier Noti 32 32 32 32 32 32 33
5. lt Q mu gt SETTINGS o 2 1 The D4 Front 2 2 The D4 Rear 9 Signal LEDs D XLR line input 1 e Clip LEDs 2 XLR line input 2 Character LCD AES input Channel buttons amp Ethernet network input 6 Item buttons Cooling air outlet vents Menu buttons SPEAKON output 2 Rotary encoder with push button SPEAKON output 1 6 Removable air filter system 2 Rating plate Cooling air inlet vents AC power cable O On Off switch O DUAL CHANNEL SS O BRIDGE 230V 50760 Hz 11 34 1220 W WENDEN OUTPUT PWR chip id LS EE o 71 ag 5 8 H 7 MADE IN GERMANY INPUT CHANNEL I CHANNEL as ETHERNET 3 5 S 7 O en C MCO iD OcH2 PA 28 lt Dome gt 4 MENU D gt SETTINGS O we O 2 3 The iD7 Front 2 4 The iD7 Rear O Signal LEDs O XLR line input 1 Clip LEDs XLR line input 2 6 Character LCD AES input Channel buttons Ethemet network input Item buttons Cooling air outlet vents 6 Menu buttons SPEAKON output 1 Rotary encoder with push button SPEAKON output 2 Removable air filter system 2 Rating plate Cooling air
6. 10k 20k 60 50 40 30 20 10 o 10 Hz dBu 8 6 THD vs frequency 120 W output power 4 load 8 8 DIM100 vs input level 4 Q load Measurement of a typical performance of aiD4 AY amp iD7 AY 32 dB amplifier gain Measurement of a typical performance of a iD4 Y amp iD7 AY 10 100 dk 10k 20k Hz 8 9 Common mode rejection ratio vs frequency Measurement of a typical performance of a iD4 Y amp iD7 AY 80 10 100 1k 10k 8 10 of noise level vs frequency No input signal applied analog input 32 dB amplifier gain Measurement of a typical performance of a iD4 V amp iD7 A 300 100 m4 10m4 2m T 8 11 Output impedance vs frequency 1 Amp RMS injected current equivalent 11 2 1 uH Measurement of a typical performance of a iD4 Y amp iD7 AY 10004 Damping factor 2004 20 100 1k 10k 20k 8 12 Damping factor into 8 Q vs frequency Equation damping factor loaded impedance amplifier output impedance Measurement of a typical performance of a iD4 V amp iD7 AY 9 Unit Conversion Equations and Lookup Table 9 2 Lookup Table 9 1 Unit Conversion Equations V Cut RMS MV dBu dBV power power power in W O 40 nw 20 Unit conversion Equation 1 maa 222 0 00 0 13 0 25 0 50 1 2 2 83 8 24 6 02 0 50 1 00 2 00 g Value in V 7 Yan dBu oid aBu aosiog Yna o ie 4 5 66 14 26 12 04 2 0
7. 7 peak dual channel 20 dual channel 2 7 0 dual channel 40 iD4 iD7 amplifiers are fitted with Switched Mode Power Supplies SMPS which significantly reduces the weight and size only 2U of the amplifier Using SMPS the 2 symmetrical supply voltages of the power amplifier are more stable than the power supplies used in conventional amplifiers The iD4 iD7 has been designed as a powerful two channel amplifier with on board 64 bit DSP processing Both amplifier settings and DSP settings can be user adjusted to match a speaker systems specifications With up to 50 onboard speaker pre set storage capability fine tuning of a system or differing Systems is fast easy and strait forward the user interface is designed to be intuitive allow for quick familiarisation The combination of both power amplifier and on board DSP technologies used in the 104 107 provide the level of control and audio quality expected in any professional applications The iD4 iD7 is a very powerful and complete speaker management system with optimum flexibility and maximum control and security Since some of the extemally mounted controls have multiple functions it is important that users should familiarise themselves thoroughly with the entire range of controls SIGNAL jO loca iD4 PRESET 28 gt D4 m O
8. X ChannelA Output Pin1 ChannelB Output Pin1 ChannelA Pin2 Channel A Output Pn2 ChamelB Output Pin 2 ChannelA Output Pin2 ChannelB Output WARNING SPEAKON connectors marked with the lightning flash indicate high vol tages that are potentially life threatening Wiring to these terminals requires installation by an instructed person or the use of ready made leads or cords Custom wiring should only be made by qualified personnel To prevent electric shock do not operate the amplifier with any of the conductor portion of the speaker wire exposed 9 NOTE For reasons of safety and performance use only high quality fully insu lated speaker cables of stranded copper wire Use the largest wire size that is economically and physically practical and make sure the cables are no longer than necessary When connecting speaker cabinets in parallel always use all the contacts in both SPEAKON connectors If not this may cause permanent damage to the connectors and may consider ably reduce performance 3 7 2 Dual Channel Operation Two fully independent amplifier channels Stereo normal operating mode iD4 iD7 w gt Mh w 2 for Dual Channel operation 3 7 3 Mono Bridge Operation One channel mono bridged operation iD4 iD7 e
9. both the line filter and the fused input of the controllable rectifier If a power cut occurs while the amplifier is switched on it will restart automatically once the power supply has been restored All amplifier settings prior to the loss of power will be maintained 3 3 Mounting Use four screws and washers when mounting the amplifier to the front rack rails For mobile use the amplifier should also be secured using the 19 mounting elements on the rear panel 3 3 1 Mounting Dimensions iD4 3 3 2 Mounting Dimensions iD7 Bem BEBBERERREEBRERRRESBRRSBRESBRESBRESBRESBRESE copado acc ooo bancadas Drop nenuwun aana awanan EEE b A e 76 20 E 7620 4 46500 442 00 449 60 462 00 418 60 43 10 48300 3 4 Cooling The air is taken in from the front and out through the back It is essential that while the amplifier is running the air is able to circulate around it freely The efficiency of the cooling will depend on the immediate environment e g an enclosed rack direct sunlight If the amp is installed in a case the open area at the back of the case must be at least 140
10. inlet vents AC power cable O On Off switch CO E EA O D O SER No AE D D D D D G ETHERNET D D D D D S HEN TTT GEN m G O 1 AN SS D D End Gm a EEE eee O ONY a O e 3 Installation 3 1 Mains Supply When mounting or connecting the amp always disconnect it from mains Only connect the iD4 iD7 amplifier to an appropriate AC circuit and outlet according to the requirements indicated in the second line on the rating plate Exemplary rating plates for the available amplifier variants MODE OUTPUT PWR PER CH IMP Dl URN SER NO MADE IN GERMANY RID LB OUTPUT PWR PER CH IMP URN SER NO ox MADE IN GERMANY MODEL OUTPUT PWR PER CH IMP SER NO _ XXXXXXX MADE IN GERMANY OUTPUT PWR CH IMP DDD SER NO MADE IN GERMANY MODEL OUTPUT PWR PER CH IMP Hi T RN SER NO MADE IN GERMANY MODEL OUTPUT PWR PER CH IMP i I RN SER NO __ MADE IN GERMANY Power supply data of all available variants Operating condition Mains Power Output current consumption power lt 05A 8w OW Amplifier standby power off Idle amplifier
11. is the automatic standby function which will set the 104 107 in standby mode if no input signal analogue and or AES is applied for a certain period of time This delay time can be set individually or switched off inside the DSPOontrol remote application through the Unit gt Configure gt Auto Standby menu If the amplifier has been set into standby through the Auto Standby func tion automatic wakeup will only work if digital AES input signal is applied again Applying analogue signal again will not wakeup the amplifier again When unsing analogue input signal exiting the automatic standby mode must be done manu ally through the user interface or the DSPControl remote application So please consider this carefully before using the Auto Standby function with analogue input signal 5 4 Power Amp Protection Systems 5 4 1 Clip Limiter Underimpedance Limiter The DSP section of the iD4 iD7 offers various limiter and compressor settings both on the signal inputs and on the signal outputs Those limiters and compres sors can be adjusted and even switched off completely if desired Disabling the limters is done by setting the thresholds to their highest values But in case the amplifier is driven into hardware clip i e when the Clip LED is glowing orange or red for longer periods of time the threshold setting of the output limiter will automatically be reduced temporarily Note that this is automatically done inside the
12. powered on 13A TOW OW 250 W per channel 9 10 5 1220 1500W 500W Amplifier standby power off lt 0 65 A 18W OW Idle amplifier powered on 11 60W OW 375 W per channel 10 5 12A 1600 1800W 750W Mains current draw and power consumption 230 V 50 Hz Measured with pink noise with crest factor of 12 dB to represent typical music signal For 120 V mains operation the current values can be multiplied by 2 3 2 On Off Switch The On Off Switch is a rocker type switch It is located on the right side of the front panel To tum the amplifier on press on the upper part of the switch During power up the Clip and Signal LEDs from both channels will light up in red for a few seconds To tum the amplifier off press on the lower part of the Switch Amplifier is switched on Amplifier is switched off This switch does NOT disconnect the amplifier from mains Disconnecting the amplifier from the main power supply can only be achieved by disconnecting the mains plug or by an external all pole disconnection e g a mains circuit breaker The mains plug or circuit breaker therefore has to be freely accessible at all times Disconnect the mains plug from the mains during a lightning storm or when the amplifier remains unused or unsupervised for a prolonged period of time The switch initiates start up by activating the inrush current limiter As soon as the power amplifier is connected to the mains power supply a voltage is sup plied to
13. were made to correct it Contact Address Telephone Facsimile E Mail Address odel Other equipment in your system Serial Number Purchase Date Expired Warranty f the warranty has expired payment will be Cash Cheque LI VISA MasterCard Our web site www camcoaudio com provides a complete list of CAMCO dealers distributors Shipping Address To transport the amplifier the original packing materials must be used Please retum the CAMCO Produktions und Vertriebs GmbH f r Beschallungs amplifier to the address on the right side or your nearest CAMCO appointed distributor und Beleuchtungsanlagen Fischpicke 5 57482 Wenden Germany 12 Maintenance Information Cleaning and servicing the inside of the amplifier must never be carried out by unqualified personnel The amplifier must never be opened by unqualified personnel Cleaning and servicing work on the inside of the amplifier must only be carried out by qualified personnel Qualified personnel is defined as a person who has gained specialised relevant knowledge of electronic engineering through education training and experi ence and who has sufficient knowledge of all relevant governmental work safety regulations to be in a position to judge the safe functioning of power amplifiers based on technical rules according to IEC 60065 IEC 60065 DIN EN 60065 Safety Requirements for Audio Video or simlar Electronic Appliances In order to guarante
14. 0 4 00 8 00 Va gt dBV T abi zoe n Bl 5 7 07 16 20 13 98 3 18 6 25 13 1 0000 6 8 49 17 78 15 56 4 50 9 00 18 7 9 90 19 12 16 90 6 18 12 25 Level in dBu F 7 dBu gt V Vaese Rd d 8 11 81 20 28 18 06 8 00 16 32 9 Ere 21 30 19 08 10 20 41 sana 10 14 14 22 22 20 00 13 25 50 ABV gt Voltage inVays 10 12 1697 2880 21 58 18 36 72 15 Di 25 74 28 52 28 56 113 Voltage inV 1 414 Voltage in 20 28 28 28 24 26 02 50 100 200 30 42 43 31 76 29 54 113 225 450 40 56 57 34 26 32 04 200 400 800 Output power in weine 50 7071 3620 33 98 318 625 1250 60 84 85 37 78 35 56 450 900 1800 Na Voltage ina 70 98 99 39 12 36 90 613 1225 2450 per O EE 80 113 14 40 28 38 06 800 1600 3200 90 12728 41 30 39 08 1013 2025 4050 Voltage in Vax a oltage IN Vays OOM pee 2 22 40 00 1250 2500 20 125 176 78 44 16 41 94 1953 3906 150 212 18 45 74 43 52 2813 5625 175 247 49 47 08 44 86 3828 7656 200 282 84 48 24 46 02 5000 Values in are calculated only The iD4 iD7 are not able to deliver these output powers 10 Warranty Information 10 1 Summary of Warranty CAMCO guarantees the iD4 and iD7 amplifier to be free from defective material and or workmanship for a period of six 6 years from the date of sale When a defect occurs under normal installation and use CAMCO will repair the product under this warranty In this event please retum the amplifier to your dealer dis tributor together with a copy of your sales r
15. 0 A peak We reserve the right to make technical alterations without prior notice Frequency response 4 Q load with 120 W ouptut power THD N over frequency 4 load with 120 W output power Damping factor 8 load 1 kHz and below Input impedance Amplifier gain Maximum analogue differential input level Level attenuation Minimum loudspeaker load impedance Lower values are safe but out of specification No performance guarantees be given when driving lower impedances than specified Protection circuits Analogue limiters HW Digital limiters SW DSP Cooling LED indicators Input connectors Power output connectors Modes of operation 10Hz 2 20 Hz 10 kHz 0 02 96 29 O KHz 0 175 dB 20 Hz 10 kHz lt 0 035 96 gt 400 0 balanced 32 dB default adjustable through DSP 20 dBu 7 75 Naya 10 95 V DSP controlled 0 25 dB steps through amplifier display 0 01 dB steps with DSPControl remote application Z 2 for Dual Channel operation min Zan 4 O for lono Bridge operation Inrush current limitation mains surge overvol Itage protection temperature monitoring of heatsinks output DC protection temperature dependent SOA protection mains fuse protection output current limitation thermal limitation Clip Underimpendance Limiter FuseProtect Limiter Zero Attack limiter for each input and output channel Fully featured comp
16. 20 7 lbs 12 7 kg 28 lbs 600x 105x527 mm 615x 135x540 mm 23 3 4 1 x 20 7 inches 24 2x5 3x21 3 inches 11 kg 24 3 lbs 15 kg 33 1 6 We reserve the right to make technical alterations without prior notice 8 Typical Performance Diagrams 017 dBr 2 0 014 3 6 4 1 0 001 T T T T T 10 100 1k 10k 50k 60 50 40 30 20 10 Hz dBu 8 1 Gain vs frequency 120 W output power 2 load 8 3 THD 1 kHz vs input level 2 load Measurement of a typical performance of aiD4 amp iD7 AY 32 dB amplifier gain Measurement of a typical performance of a iD4 Y amp iD7 A 15 15 dBr 3 0 014 3 6 4 1 0 001 10 100 1k 10k 50k 60 50 40 80 20 10 Hz dBu 8 2 Gain vs frequency 120 W output power 4 load 8 4 THD 1 kHz vs input level 4 load Measurement of a typical performance of aiD4 amp iD7 AY 32 dB amplifier gain Measurement of a typical performance of a iD4 Y amp iD7 A 204 40 4 801 0 014 804 1004 0 001 T T 1 120 T T T T 20 100 1k 10k 20k 10 100 1k 10k 20k Hz Hz 8 5 THD vs frequency 120 W output power 2 load 8 7 Channel separation vs frequency 9 120 W 4 Q Measurement of a typical performance of a iD4 AY amp iD7 AY Measurement of a typical performance of a iD4 AY amp iD7 M 14 104 0 1 0 14 0 014 0 001 1 0 001 T T T T T T 1 20 100 1k
17. 34 34 35 36 Welcome to the D Series user manual Revision H 2015 03 13 Please visit our website www camcoaudio com for the latest version of this user manual Please note that the leading version of CAMCO manuals is always the English one Copyright 2015 by CAMCO Produktions und Vertriebs GmbH Tur Beschallungs und Beleuchtungsanlagen Important Safety Instructions 1 General The amplifier may only be used in accordance with the information provided in the user manual Before and during the usage of the amplifier please ensure that all recommendations especially the safety recommendations as detailed in the user manual are adhered to The iD4 iD7 amplifier is designed for the amplification of pulsed audio signals The amplifier should only be connected to speakers with an average impedance as indicated 2 User Manual Read the information for use user manual and heed all wamings Keep this user manual in a safe place during the lifetime of the amplifier The user manual forms an integral part of the amplifier Reselling the amplifier is only possible if the user manual is available In case of reselling the amplifier the reseller has to docu ment any changes made to the amplifier in writing and pass the documentation on to the buyer 3 Environments Use this amplifier only in E1 E2 or E4 environments according to EN55103 2 Electromagnetic compatibility Product family standard for audio vid
18. 7 ID Series ADVANCED AMPLIFIERS USER MANUAL Welcome to the D Series user manual Important Safety Instructions Explanation of Symbols EC Declaration of Conformity 1 Welcome to CAMCO 1 1 Unpacking 2 The Amplifier 2 1 The iD4 Front 2 2 The iD4 Rear 2 3 The iD7 Front 2 4 The iD7 Rear 3 Installation 3 1 Mains Supply 3 2 On Off Switch 3 3 Mounting 3 3 1 Mounting Dimensions D4 3 3 2 Mounting Dimensions 07 3 4 Cooling 3 5 Signal Inputs 3 5 1 Analog Input 3 5 2 AES Input 3 6 Remote Control Network Input 3 7 Power Outputs 3 7 1 SPEAKON Connection 3 7 2 Dual Channel Operation 3 7 3 Mono Bridge Operation 4 Signal Processing Block Diagram 5 Operation 5 1 User Interface Elements 5 1 1 Signal Protect LEDs multifunctional 5 1 2 Clip LEDs multifunctional 5 1 3 CHANNEL Buttons 5 1 4 ITEM Buttons 5 1 5 MENU Buttons 5 1 6 Rotary Encoder with Push Button 5 2 Hot Key Functions Standby 5 3 Standby Function 10 11 12 12 13 13 14 15 15 15 16 16 16 16 16 16 16 17 17 18 19 19 19 19 19 19 20 20 20 20 5 4 Power Amp Protection Systems 5 4 1 Clip Limiter Underimpedance Limiter 5 4 2 SOA Protection 5 4 3 DC Protection 5 4 4 Over Current Protection 5 4 5 Thermal Protection 5 5 Mains Protections 5 5 1 Inrush Current Limitation 2 Mains Over Voltage Detection 5 5 3 Mains Surge Overvoltage Protection 5 5 4 Mains Failure Detec 5 5 5 Fuse Protection
19. ED s will glow in orange or red colour for short periods of time while the amplifier is playing music gt See also chapter 4 5 5 Fuse Protection 5 1 2 Clip LEDs multifunctional SIGNAL CLIP lt CAMCO 0 H2 PRESET 28 The colour of the bi coloured LED changes between orange and red depend ing on the clip intensity Orange indicates light clipping red indicates heavy clip ping These LED s exclusively indicate hardware clipping of the power amplifier stage Possible internal DSP limitation and compression is not indicated here r SIGNAL CLIP O CAMCO iD4 PRESET 28 4 D4 Q O SETTINGS 5 1 3 CHANNEL Buttons The CHANNEL buttons allow to select the channels to make adjustments on Selectable items are In 1 to 4 and Out 1 and Out 2 depending on user and access rights Note that if channels are linked the settings will always affect both linked channels In this case the channel selection will display In 12 In 34 or Out 12 5 1 4 ITEM Buttons The ITEM buttons allow you to navigate trough all parameters which can be set from the front panel Note that not all parameters can be set from the amplifier user interface For full and easier access to all settings and parameters please use the DSPControl remote control application The available parameters are Gain gt Gain settings 0 25 dB
20. amplifier and cannot be seen in the DSPControl application This automatic threshold reduction will especially take place at low output impedances smaller 4 O and high output powers and shall prevent the ampli fier from being operated in continuous hard amplifier cliping 5 4 2 SOA Protection Whenever the power transistors leave their Safe Operation Area SOA the SOA protection switches back the rail of the respective channel 5 4 3 DC Protection Each output of the power amp is constantly monitored for persistent DC voltage levels If the 3 V thresholds are exceeded at any of the outputs the correspond ing channel will be muted was only detected for a short moment the ampli fier will release mute and work as normal If DC is detected for longer periods or repeatedly the amplifier will switch to standby mode and disable the main power supply If this happens the display will indicate Error amp switched off In this case switch off the amplifier for at least 4 minutes and switch the ampli fier on again 5 4 4 Over Current Protection Over current is permanently controlled in the output stage There are two limiting levels of over current depending on output voltage These limits will be set auto matically This improves reliability without degrading sound quality when driving complex loads 5 4 5 Thermal Protection There are several sensors inside the amplifier in order to ascertain temperature data If a temper
21. amplifier from the mains supply and refer to your dealer distributor or other authorized repair workshop if any of the following situations occur if liquid has been spilled or objects have fallen into the amplifier if the amplifier has been exposed to rain or moisture if the amplifier has been dropped or damaged in any other way if the power supply cord or plug has been damaged when the amplifier exhibits a distinct change from its normal function or performance in case the amplifier has been used in a dusty environment for quite a period of time 14 Servicing All service and repair work must be carried out by a dealer distributor author ized by CAMCO Do not attempt to service this amplifier yourself As opening or removing covers may expose you to dangerous voltage or other hazards the amplifier may only be opened by qualified personnel Please refer to your dealer distributor 15 Spare parts When spare parts are required please ensure that the dealer distributor only uses spare parts specified by the manufacturer The use of unauthorized spare parts may result in injury and or damage through fire or electric shock or other electricity related hazards 16 Safety check Upon completion of any service or repairs to this product ask the dealer dis tributor to perform safety checks to determine that the amplifier works properly Recommendations on how to carry out the safety test can be found in DIN VDE 0701 1 Maintenance M
22. ature of more than 85 C is detected at the heat sinks the input Signal on that channel is reduced 5 5 Mains Protections 5 5 1 Inrush Current Limitation Within 2 seconds of the amplifier being switched on the inrush current limiter will increase mains current from nearly zero to nominal value This value depends on program material output level and speaker loads 5 5 2 Mains Over Voltage Detection Mains over voltage detection is always operative When the mains voltage exceeds approx 263 V 220 230 V operation or 134 V 110 120 V operation the amplifier will be switched off The system will try to restart in intervals and will retum with a soft start when the regular mains voltage retums 5 5 3 Mains Surge Overvoltage Protection The iD4 iD7 is fitted with a varistor unit protecting the SMPS from sporadic surge overvoltages coming from the mains distribution 5 5 4 Mains Failure Detection Mains failure detection is always operative When the mains supply is interrupted for about 2 mains cycles the amplifier will be switched off When the mains volt age retums to a normal value a soft start occurs 5 5 5 Fuse Protection When driving the 104 107 at very high output levels over a longer period of time several seconds and minutes the average mains current draw can become very high In such situations the FuseProtect limiter will reduce the output signal in order to prevent the external mains breaker from tripping Bu
23. e the safe functioning of the amplifier it has to be checked regularly depending on its application but at least once a year by a properly qualified person Advice on how to carry out these checks can be found in DIN VDE 0702 1 Safety Checks for Electronic Appliances An amplifier that is considered to be unsafe must be labelled accordingly and Stored in a safe place to prevent this amplifier being used mistakenly 13 Decommissioning During the decommissioning process of the amplifier all legally prescribed rules and procedures must be adhered to Company information Mailing address CAMCO Produktions und Vertriebs GmbH f r Beschallungs und Beleuchtungsanlagen Fischpicke 5 57482 Wenden Germany Telephone 49 0 27 62 408 0 Facsimile 49 0 27 62 408 10 Internet www camcoaudio com E Mail postmaster camcoaudio com Changes Made to The Amplifier Notices Please consider that any changes made to the amplifier have to be documen tated in writing and passed on to the buyer in the event of resale CAMCO www camcoaudio com MADE IN GERMANY
24. eceipt as proof of purchase This warranty provides that examination of the retumed product must indicate in our judgment a manufacturing defect 10 2 Items Excluded from This Warranty CAMCO is not liable for any damage caused by shipping accidents misuse abuse operation with incorrect AC voltage operation with faulty peripheral equipment modification or alteration without prior factory approval service by an unauthorised service center and normal wear and tear Amplifiers on which the serial number has been removed or defaced are not eligible for warranty service 10 3 What CAMCO Will Do CAMCO or its appointed agent undertakes to rectify any defect regardless of the reason for failure unless excluded from this warrenty by repair replacement or refund as it sees fit 10 4 How to Obtain Warranty Service You must notify your dealer distributor of your need for warranty service All components must be shipped in the original packaging 10 5 CAMCO Product Improvement CAMCO reserves the right to improve the technical standard of its products without giving prior notice If in any doubt please consult your dealer distributor or contact CAMCO directly for clarification 11 Service Information PLEASE ENCLOSE THIS COMPLETED FORM WITH THE AMPLIFIER DO NOT SEND SEPARATELY Owner s Information Nature of problem occurred Please describe the conditions that existed when the problem occured and Company Name what attempts
25. eo and audio visual and entertainment lighting control apparatus for profes Sional use Part 2 Immunity 4 Mounting Placement Do not place this amplifier on an unstable cart stand tripod bracket or table The amplifier may fall causing Serious injury and serious damage to the product Any mounting of the amplifier should follow the manufacturer s instructions Only mounting accessory shall be used which is recommended by the manufacturer 5 Mains Connection The amplifier may only be connected to a socket with a protective earth con nector 6 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon them or against them paying particular attention to cords and plugs and the point where they exit from the amplifier The disconnection device from mains mains plug or external all pole circuit breaker shall remain readily operable and freely accessible at all times 7 Heat Do not use this amplifier near any heat sources such as radiators heat registers Stoves or other apparatuses that produce heat 8 Water and Moisture Do not expose this device to rain moisture dripping or splashing water Do not use this amplifier near water for example swimming pools and fountains Do not place any objects containing liquids such as bottles or glasses on the top of the unit Do not splash liquids on the unit IP 20 equipment There is no protec tio
26. ff This can be caused by Detection of permanent DC on the outputs Detection of amplifier stage malfunction Protect Detection of main SMPS error You can try to power oycle the amplifier to reset all amplifier stage detection cir cuits This might help in case the DC or amplifier fault was caused by an invalid input signal e g an extremely high frequent or extremely distorted input signal Q NOTE For this please unplug the amplifier from the mains for at least 4 minutes and switch the amplifier on again If the message still appears after this procedure the fault is permanent and the amplifier requires servicing 7 Specification Output power 1 kHz THD lt 196 in dual channel operation typical values 230 V 50 Hz duration limited by fuse thermal protection for RL lt 8 Q Peak output power 1 kHz single sine wave in dual channel operation typical values Q 230 V 50 Hz may be subjected to component tolerances Mono bridge operation output power 1 kHz THD lt 1 in mono bridge operation typical values 230 V 50 Hz duration limited by fuse thermal protection for RL lt 160 1 kHz single sine wave in mono bridge operation typical values 230 V 50 Hz may be subjected to component tolerances 70 100 V line operation output power 1 kHz THD lt 1 only possible in mono bridge operation single channel Circuitry Signal to noise ratio 10 Hz 20 kHz 8 load Power consumpti
27. in VU Meter Peak Limiter Crossover Delay Mute Crossover Delay Mute Crossover Delay Mute Crossover Delay Mute Output DSP 1 Mixer m 1 Gain Crossover Peak Limiter VU Meter PEQ 10x Phase Invert Output DSP 2 Mixer 1 Gain Crossover Peak Limiter VU Meter Number of signal streams PEQ 10x Phase Invert Power Loud Amplifier speaker Output Compressor Delay Mute DAC Compressor Delay Mute DAC Refers to firmware version v3 6 9 5 Operation 5 1 User Interface Elements This chapter only describes the basic user interface operation and functions Please refer to the separate DSPControl manual for an explanation of the exten sive Digital Signal Processing DSP options and advanced features offered by the remote application 5 1 1 Signal Protect LEDs multifunctional SIGNAL CAMCO PRESET 28 The Signal LEDs are illuminated in green when the voltage level at the output reaches approx 4 V this corresponds to a power of 4 W into a 4 O load The channel Signal LEDs are illuminated red when the amplifier is in Protect Mode Mute for example because of persistent DC voltage at the outputs or over heating When switching the amplifier on the Signal LEDs will also light red for a few sec onds while the DSP is starting up along with the Clip LEDs In case the Fuse Protect limiter is activated it is possible that the green Signal L
28. it should and may result in reduced output levels 04 107 Filter Assembly Foam filter Front frame 6 Screw A WARNING Turn off and disconnect the amplifier from the mains before removing the front frame To clean or replace the filter just slightly unscrew the fixing screw with the help of a 3 mm allen key The screw will be held back by a small plastic spacer on the back of the frame to avoid losing it Then shift the front frame slightly to the right Then you should be able to remove the frame from the amplifier completely pull gently to avoid any bending of the front frame 6 Troubleshooting 6 1 Problem No reaction when switching the amplifier on If nothing happens when switching the amplifier on i e the display stays totally dark no message inside the display please check following points Check mains cable and plug Confirm that the AC outlet works by plugging in any other device 6 2 Problem No sound If no sound can be heard on the outputs please check following DSP settings through the DSPControl application source selection nput and output gain settings nput and output limiter settings f digital AES input signal is used please check AES signal source samplig requency bit resolution and signal quality long cables 6 3 Problem Error message Error Amp switched off This error message indicates an internal error which forced the main power supply SMPS to be switched o
29. n against splashing water 9 Ventilation Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the amplifier and to protect it from overheating These openings must not be blocked or covered This amplifier should not be installed unless proper ventilation is provided or manufacturer s instructions have been adhered to 10 Interference of External Objects and or Liquids with the Appliance Never push objects of any kind into this amplifier through openings as they may touch dangerous voltage points or short out parts that could result in fire or electric shock Never spill liquid of any kind on the amplifier 11 Connections When you connect the amplifier to other equipment tum off the power and unplug all of the equipment from the supply source Failure to do so may cause an electric shock and serious personal injury Read the user manual of the other equipment carefully and follow the instructions when making the connections 12 Lightning For additional protection of this amplifier during lightning storms or when it is left unattended and or unused for long periods of time unplug it from the wall outlet This will prevent damage to the amplifier due to lightning and power line surges Disconnection from the mains power supply can only be achieved by removing the plug from the mains socket and by external disconnecting all poles from the mains 13 Damages that require service Unplug this
30. odification and Test of Electronic Appliances 17 Cleaning Unplug this amplifier from the wall outlet before cleaning Do not use liquid or aerosol cleaners Clean only with dry cloth 18 Packaging and shipping When shipping the D4 amplifier always use the original shipping carton and packing materials For maximum protection repack the unit as it was originally packed at the factory 19 Altitude for China The amplifier shall only be operated at altitudes below or equal 2000 m 20 Non tropics for China The amplifier shall only be operated in non tropic areas Explanation of Symbols CAUTION CAUTION HIGH VOLTAGE HAZARDS EXIST WITHIN THIS PRODUCT RISK OF ELECTRIC SHOCK REFER ALL SERVICING TO DO NOT OPEN AUTHORIZED PERSONNEL THE LIGHTNING FLASH WITH ARROW HEAD SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED DANGEROUS VOLTAGE WITHIN THE PRODUCT S ENCLOSURE THE EXCLAMATION MARK IS INTENDED TO ALERT THE USER TO IMPORTANT INSTRUCTIONS ALSO FOR MAINTENANCE IN THE LITERATURE ACCOMPANYING THE AMPLIFIER THE LIGHTNING FLASH WITH ARROW HEAD SYMBOL ALERTS THE USER TO DANGEROUSLY HIGH VOLTAGE AT THE OUTPUT CONNECTORS THAT COULD POTENTIALLY BE LIFE THREATENING CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS AMPLIFIER TO RAIN OR MOISTURE THE AMPLIFIER MAY ONLY BE CONNECTED TO A SOCKET WITH A PROTECTIVE EARTH CONDUCTOR EC Decla
31. on 230 V both channels driven at 250 W output power approx of max THD limited output power with pink noise to represent typical music signal Maximum output voltage in dual channel operation typical values 230 V 50 Hz Maximum output current in dual channel operation typical values may be subjected to component tolerances 2x 600W 160 2x 1100W 80 2 1900W 40 2x 1950 W 2 70 2 1450W 20 2 680W0 160 2 1240WQ 80 2 2250WQ 40 2x 2000 W Q 2 7 0 2 1500W 20 1 2200W 160 1 3800W 80 1 2900W 40 2480 W Q 160 peak 4500W peak 3200W 40 peak 1800WQ 70V line 2500 W 100 V line 1 1 1 X X X 2 1 9 CX Bipolar Class H 2 step high efficiency circuit gt 103 5 dB unweighted gt 106 dB A weightea Amplifier standby power off 8 W ldle Amp powered on 70 W 40 1220W 20 1500 W 142 V peak 39 A peak 2x 750W 160 2 1380W 80 2 2800WQ 40 2 2950W 2 7 0 2 3440W 20 2x 780W 160 2 1490W 80 2x 2800W 40 2 3850 W 2 70 2 8700W 20 1 2760 160 1 4600 80 1 6880 40 2980W 16 peak 5600 peak 7400W 40 2 83000WQ 70V line 2 1890W 100 V line ER X X X Bipolar Class H 3 step high efficiency circuit gt 105 dB unweighted 107 5 dB A weighted Amplifier standby power off 18 W Idle Amp powered on 60 W 40 1600 W 2 0 1800 W x 165 V peak 6
32. ration of Conformity EC Declaration of Conformity in accordance to EC Directives Electromagnetic compatibility Council Directive 2004 108 EC low voltage electrical equipment Council Directive 2006 95 EC Manufacturer s Name CAMCO Produktions und Vertriebs GmbH r Beschallungs und Beleuchtungsanlagen Manufacturer s Address Fischpicke 5 D 57482 Wenden Germany Declares that the product with the model name CAMCO Power amplifier iD4 iD7 Conforms to the following standards IEC EN UL CSA 60065 GB 8898 Safety EN55103 1 Emission EN55103 2 Immunity The operating conditions and application environments presupposed in the information for use user manual are to be kept accordingly Wenden 17 06 2013 Joachim St cker 1 Welcome to CAMCO Thank you for choosing CAMCO products You are now the proud owner of a very advanced CAMCO Amplifier The technologies used in your amplifier are of the latest generation and designs delivering a far reaching set of results across all functions The amplifier has been designed to be incorporated into a professional speaker System and is suitable for use across all applications from Touring Live Sound to Fixed Installations Your speaker systems will benefit from the renowned CAMCO sonic quality as well as the many operating functions and features detailed within this manual which are incorporated within the design to maximise results The CAMCO peace of mind long term manufacture
33. ressor for each input channel Fully featured 6 band BLC Bandwidth Limited Compressor for each output channel Two temperature dependent speed controlled axial fans LED s for signal protect and clip Two 3 pin XLR female analogue input connectors pin 2 hot inphase Two 3 pin XLR male passive loop through connectors One 3 pin XLR female AES digital input connector One Ethernet connector RJ45 One 4 pole SPEAKON connector for each output channel bi amping possilbe Dual Channel Stereo Mono Bridge We reserve the right to make technical alterations without prior notice Input sources A D D A converters Latency Digital inputs AC mains operating range 230 V AC 50 60 Hz for Europe 220V 50 60 Hz for China 120 V AC 50 60 Hz for US Approximative mains voltage range where the amplifier can be used Amplifier output power performance wil decrease with lower mains voltages than the rated 230 V 220 V 120 V and slightly increase with higher mains voltages Operating temperature Non condensing Dimensions W x H x D Net weight Shipping dimensions W x x D Shipping weight Analogue AES 24 bit 96 kHz Min 0 58 ms AES EBU 16 to 24 bit 44 1 48 88 2 or 96 kHz 190 263 V 175 265 V 190 263 V 115265 95 134 V 90 135 V 5 C to 55 41 F to 131 F 483 x 88 1 x419 mm 483 x 88 1 x 446 mm 19 3 5 16 5 inches 19x3 5x 17 6 inches 19 2U 19 20 9 4 kg
34. s warranty is our commit ment to you that every CAMCO amplifier is ready to give you many years o faultless service 1 1 Unpacking Please unpack and inspect your new amplifier for any damage that may have occurred during transit If damage is found notify the transportation company immediately Only you the consignee may initiate a claim for shipping damage CAMCO will be happy to cooperate fully as needed Please save the shipping carton as evidence of damage for the shipper s inspection Even if the amplifier has arrived in perfect condition save all packing materials so you will have them if you ever need to transport the unit Never ship the amplifier without the original packing materials When shipping the iD4 iD7 amplifier always use the original shipping carton and packing materials For maximum protection repack the unit as it was origi nally packed at the factory 2 The Amplifier The iD4 iD7 is a Class H power amplifier with a power output of Power output 1x4500W 1x 3800 W 1x 3200 W 2x 2250 W 2x 2000 W 2 1900 W 2x 1450 W 1x 7400 W 1x 6800 W 1x 5600 W 2x 3850 W 2x 3440 W 2x 2950 W 2x 2300 W Operating mode mono bridge mono bridge mono bridge dual channel 8 peak 80 40 4 Q peak dual channel 2 7 peak dual channel dual channel mono bridge mono bridge mono bridge 40 ao 40 peak 40 8 peak dual channel 2
35. steps Smaller steps 0 01 dB can be set via the DSPControl remote application gt Selects the source of the chosen input channel Setting only available for the Inputs 1 to 4 Delay gt Set the signal delay Low Pass gt Configure the low pass filter section Source High Pass gt Configure the high pass filter section PEQ 1 to 10 gt Configure the 10 parametric EQ bands Phase gt Set the Output channel phase normal or inverted Setting only available for Output 1 and 2 Limiter 3 Configure the peak limiter Compressor gt Configure the compressor Link gt Selects if Input 1 amp 2 Input 3 amp 4 or Output 1 amp 2 shall be linked All settings and selections are done through the rotary encoder Changes will take effect immediately 5 1 5 MENU Buttons The left 4 MENU button will always act as ESCAPE EXIT button The right MENU button offers following sub menus accessible through repeated pressing on the right MENU button Load preset Save preset Access Level control Auxiliary information gt Version Info Serial Number SN gt Version Info FW Version SW gt Version Info Hardware Version HW gt IP Address gt MAC Address gt Temperature of both amplifier stages Inside the Auxiliary information menu you can navigate through the sub menus with the encoder wheel Note that in this menu the encoder will only work in a round robin fashion regardless of the direction you tum it
36. t this limiter in tum will not affect the output signal on dynamic music signal and short current peaks thus guaranteeing the full available peak output power Please note that the FuseProtect limiter only controls the average mains input current not the short term peak input current This means that with very dynamic music signals the short term input current can still reach very high levels which can be very demanding for a mains distribution The operation of the FuseProtect limiter can be seen by short orange or red glowing of the Signal LED s in the iD4 In the iD7 the FuseProtect limiter cannot be seen from the signal LED s 5 6 Main SMPS Protections 5 6 1 Over Current Protection Main SMPS Switched Mode Power Supply transformer current is continuously monitored If over current occurs the main SMPS immediately stops working Should there be an internal failure this feature prevents other parts being dam aged 5 7 Fans The fans mounted in the 104 107 operate permanently but as long as the tem perature remains below 40 C they run at their slowest speed and can hardly be heard The highest detected temperature from either channel controls the speed of the fans above 40 the speed is increased until it reaches its maximum value 5 8 Filter Cleaning The air intake on the front of your iD4 iD7 amplifier is fitted with a removable filter system If the filter becomes clogged the unit will not cool as efficiently as
Download Pdf Manuals
Related Search