Installation Instructions
Contents
1. Expand Your Factory Radio add Bluetooth Calling Owner s Manual Neo Bluetooth BAD3V9 BMBU3V9 BBMW3V9 BMX3V9 BHD3V9 BSB3V9 BHD93V9 BTOY3V9 BLR3V9 BTY3V9 BLX3V9 BVWDS3V9 BMB3V9 BVWI3V9 ENJOY THE MUSIC Installation Instructions Chapter 1 Getting Started 1 1 Subject The Neo Bluetooth adapter will provide seamless Bluetooth integration into many factory car stereos When connected to the car stereo the adapter provides wireless hands free operation with accept reject call features The Neo Bluetooth adapter also enables wireless A2DP music playback with AVRCP control 1 2 Introduction Thank you for purchasing the NEO Bluetooth adapter which has been designed to provide endless hours of listening pleasure through most vehicles factory radios With the Bluetooth Dongle you will be able to e Use your phone in your car hands free e Stream your MP3 or internet radio music and control it where applicable with the stereo buttons e Hear GPS voice announcements and more when applicable To insure that your Bluetooth interface performs correctly in your vehicle we recommend that you read this entire manual before attempting installation 1 3 Precautions Proper mounting location Securely install the interface in a location that is free from heat humidity moving parts or direct sunlight Beware of hot airflow from your vehicle s climate control system We recommend securing the interface to a suitable location2. free of sharp metal edges using double sided tape Velcro or wire ties 1 4 Disclaimer e This product is not affiliated with any of the OEM manufactures e Modifying the radio may void any outstanding warranty e While every care has been taken to provide a quality product we cannot guarantee that the Neo Bluetooth adapter will function correctly if installation is not done according to the instructions provided in this guide We also cannot guarantee that the NEO Bluetooth adapter will function correctly with a device that is broken or damaged or not supported e Keep your eyes on the road while driving e We are not liable for the misuse of this product Misuse includes improper installation damage to the board or radio while trying to install it and the illegal use of the radio 1 5 Completeness and connection of set a NEO Bluetooth adapter set consists of the following see figure 1 Vehicle specific cable Module Bluetooth Dongle b Basic wiring diagram of NEO Bluetooth adapter see Figure 2 BACK OF THE CAR RADIO Data cable Bluetooth 1 6 Important Compatibility Notes If your vehicle is equipped with an external factory CD changer you must disconnect it in order to be able to install the interface You will lose the use of the external CD changer to gain the use of your Bluetooth adapter Any built in CD changer will remain working Chapter 2 General Installation 2 1 Installation location Most instal
3. reaching the microphone Carefully route the microphone cable to where the module is installed Connect the microphone to the female audio plug on the bluetooth dongle Make sure the mic is connected securely and all the way into the 3 5mm port see picture below 12 Once the interface is connected to the radio you will need to test the operation of the interface before re assembling the dash 13 Turn your car stereo on and switch it over to the CD Changer mode using the Disk Mode CD AUX depending on the stereo type buttons on your car stereo until it shows Disk 1 Track 01 on a the display Follow the operation instructions in sections 2 4 2 6 to test the interface 14 Once the operation of the interface is confirmed you may continue with the installation If you experience difficulties with the installation please see our troubleshooting section 15 Find a place where you can place the NEO Bluetooth adapter We recommend placing the module in a place that is easily accessible Note Make sure you mount the NEO Bluetooth adapter in a place with enough room so that when you re mount the car stereo you do not break the adapter 16 You may use the glove box or other spaces inside the dash to direct Audio cables to a convenient location 17 Re mount your car stereo making sure its clips or strews are secure Congratulations You have installed the Neo Bluetooth adapter You may now use it with your cellular device 2 4
4. stereo bod grounded iBus wire has come loose Make sure the iBus wre is securely Sometimes when using Posi Tap attached by using multimeter or clips the iBus wire may not receive slightly tighten up the Posi Tap proper connection due to its wire size connector Make sure that 10 pin sound Audio is coming only The 10 pin sound connector is not connector on the vehicle cable is from 1 speaker aligned correclly aligned correctly Once you turn on the vehicle the adapter becomes discoverable for 3 minutes You cannot pair my phone You are not pairing within the 3 minute must pair your phone within that 3 minute with the Neo adapter pairing timeframe interval Please reset your phone and try to pair again I cannot pair my phone You can reset your phone by turning it off and with the Neo adapter Your phone needs to be reset on or pulling the battery out Reset Instructions 41 Change from CD Changer SAT mode FM for example 2 Wait 3 4 seconds 3 Switch back and after 1 second press SCAN The unit needs to be reset This will clear the or REPEAT button on the stereo I cannot pair my phone pairing memory of the 4 You will hear a low beep confirming the with the Neo adapter Bluetooth dongle reset Please make sure to position the microphone The sound from the in a location that is free from obstruction and microphone is distorted The microphone is not positioned correctly or not facing user Make sure 3 5mm of mic is or muted sec
5. BROWN wire ground in the 1 pin position Please make certain you use this connector The INCORRECT factory cellular phone connector has a BROWN wire in the center position DO NOT USE THIS CONNECTOR 8 For Toyota vehicles only In some Toyota Lexus Scion vehicles the CD changer port is occupied with a factory harness such as NAV or audio harness The NEO package for Toyota includes a Y shaped vehicle cable In order to connect interface properly please follow to the scheme below Plug into headunit 1 p To Neo Module 3 Connect to the Factory Audio N harness or NAV harness 2 Figure 4 Connection scheme for Toyota Lexus Scion If the car does not have NAV or XM leave the female end of the Toyota harness open 9 For Honda Acura 03 and never HON1 adapter and Chrysler Dodge Jeep with navigation or XM installed you may need HON1 Y Y cable or CHR Y cable in order to gain the access to the car stereo port occupied with the factory connector Please contact Neo Car Audio for more information 10 Connect the Bluetooth dongle 8 pin connector to the EXT1 port of the module Mount the dongle module away from metal structures in the dash and as close to the phone as possible 11 Choose a proper mounting location for the microphone such as near the rear view mirror or sun visor Avoid mounting the microphone by the side windows to eliminate extra noise Please also avoid mounting behind visor to avoid blocking voice from
6. Pairing with the Phone You will need to pair your phone with your Bluetooth receiver only once 1 Please make sure that Bluetooth function on your phone is active or turned on and that the phone is set to be discoverable mode before turning the key Refer to your phone s user manual to learn how to turn on and initiate the pairing feature 2 Turn ON vehicle and radio The Neo Bluetooth will become discoverable by your phone for 3 minutes You must pair your phone within that interval 3 The pairing needs to be performed only once After pairing is completed your phone will automatically connect to the interface each time the ignition is turned on whether radio on or off NOTEI1 Your phone can ask for confirmation and you can get the pop up message Confirm that the passkey is shown on GROM CAR Click PAIR then A random pin will pop up you should only have to press Connect NOTE2 Certain vehicle electrical systems may activate the interface upon vehicle unlock NOTES The Bluetooth interface is on as long as vehicle is on If radio is OFF and you are receiving a call you can answer automatically by turning ON the radio and selecting the adapter mode 2 5 Using your phone in the hands free mode Once the Bluetooth is paired with the phone and the stereo is in CD Changer mode you can start using your phone hands free Once you receive the phone call the stereo will mute and you will hear the incoming call a
7. lations will require you to remove the factory radio in order to plug in the vehicle specific harness For some vehicles you will also have the option to connect the interface to the factory pre run CD changer cable located in the trunk or glove box 2 2 Tools needed In many cases there are no special tools required in order to remove the stereo Radio removal tools are available for some stereos to aide in the removal of the radio Please consult your local car audio shop or your vehicle s dealership for instructions or assistance if necessary If you are unsure how to install the interface properly we recommend contacting your local car stereo shop for the assistance 2 3 Preparation and adapter installation l 2 3 Turn off car engine and remove key from ignition If your radio uses a Security Code make sure that you have the code before unplugging the radio Un mount your radio from the dash in order to get access to the back side of the radio Some vehicles require special tools to remove the radio Please consult your vehicle s dealership or a local car audio professional if necessary Attach the car harness connector to the back of the stereo to the CD changer port Be sure to make a firm connection but do not force it Connect the other end to the module WV AUDI SEAT SKODA there is a black single cable on the vehicle specific harness 3 You will need to attach it to the back bolt of the car stereo or to the s
8. nd you are able to 1 Answer Call Press next track or track up 2 Reject Call Press previous track or track down 3 End Call Press previous track or track down 4 Call Waiting answer a second call Press next track or track up 5 Voice dialing Press SCAN twice within 3 seconds while in CD Changer mode You can only initiate voice dialing when there is no music streaming over Bluetooth Do not press SCAN within first 5 seconds of entering CD Changer mode To make a phone call 1 Dial the phone number on your phone 2 Once the phone is dialing the music will mute and the call will be heard over the cars audio system You will now be able to continue your call hands free NOTE If your stereo is not in CD Changer mode and you receive a phone call simply switch to CD Changer mode to be able to answer the call hands free 2 6 Streaming your music wireless and using A2DP Audio Controls With the Neo Bluetooth interface you are able to stream the music from your mobile phone directly to the car stereo system wirelessly and control it with the car stereo and steering wheel controls 1 When A2DP advanced audio distribution profile music starts playing other audio will mute and A2DP will play 2 To stop music playing stop playback on your phone Playback of the previously selected source will resume 3 Control A2DP music track selection by using track up and track down on the car stereo or steering wheel buttons Some ap
9. ps may not support track control 4 Changing car radio mode to a different source will pause A2DP playback 2 7 When the car ignition is OFF When you turn your car ignition or car stereo off music will remain playing You will need to turn the music off manually if you do not want it to continue playing 2 8 Available Upgrades e Additional auxiliary input with USB charging e Direct iPod iPhone integration with full control and charging e Direct Samsung Galaxy integration with full control and charging Chapter 3 Support Troubleshooting Symptom Case Remedy S ee ee ee Check the cable connections After connecting the adapter turn the Radio is not Some car stereos have to be restarted before the stereo on and then turn the ignition recognizing Neo Adapter _ radio catches the signal off and back on recognizing Neo Adagter extemal co changoris E e e nn recognizing Neo Adapter _ External CD changer is present CD changer Bad cables or cables are not Radio is not connected properly between the interface box Check connection and cables push recognizing Neo Adapter _ and car radio in firmly You cant hear the Make sure CD changer SAT mode music from the audio or AUX is selected correct button device No CD changer is selected depends on your stereo Single black wire on the vehicle Attach the black cable to the car specific harness 2 see Figure 3 is stereo body and make sure tt is properly not attached to the stereo chassis
10. tereo chassis Vehicle harness 1 Figure 3 VW AUDI Seat Skoda onnection scheme Black wire 2 Remove the PVC from the end of the black wire 2 a Connect the end of the black wire 2 to the metal part of the car stereo chassis You can connect it under the bolt 3 if present b Make sure that the solid contact is maintained between the striped black wire and the metal part of the car stereo body The failure to attach the black cable to the chassis of the stereo will mean that the NEO adapter will not work All VW AUDI Seat Skoda vehicles require this black cable to be attached 6 For AUDI vehicles only For some AUDI head units an additional part or harness modification is required in order to gain the access to the CD changer port The 8 pin CD changer port on such stereos is occupied by a solid 20 pin connector Please contact Neo Car Audio tech support for further information 619 704 0690 Adapter mounting in the trunk for select VW and BMW only e Locate the trunk mounting cable in your car usually located along the left side of the car in the back e Disconnect the existing CD changer if present e Attach the matching cables e For BMW trunk installation Some BMW s are factory wired for a cellular phone Except for wire location the factory cellular phone connector looks identical to the factory 3 pin connector used for the CD changer The CORRECT 3 pin connector for the CD changer has a
11. ure Reset Instructions 1 Change from CD Changer SAT mode FM for example 2 Wait 34 seconds 3 Switch back and after 1 second press SCAN or REPEAT button on the stereo You have paired too many phones to the 4 You will hear low beep confirming the reset Cannot connect to Bluetooth dongle pairing memory will need to be 5 Delete old grom car from the phone pair a Bluetooth reset cleared new grom car that comes up after reset For technical support please contact Neo Car Audio 619 704 0703
Download Pdf Manuals
Related Search