PSA - Manuale utente
Contents
1. In this example a LIN103 type peripheral on local network with TCP protocol has been created Unit name Tst floor control Unit type ft 103 r Communication The IP address is that configured on the remote LIN103 Remember that the LIN103 must be configured as Com port Multipoint address SLAVE C R5232 C R5405 Note S600 N81 At the moment RS485 multipoint connection is not available for the LIN102 and LIN103 units IP address Fort This parameter is reserved for future i F fi52 168 1 200 fion developments String T 02 Protocol ao ms Tcr Unit response time out 200 Ins OF Cancel The default parameters set relating to e String T O time out to detect end of reception of a packet for IP protocols e Unit response time out peripheral response time out are optimized for serial interface or on LANs if the Internet is used as interface it may be necessary to modify these parameters In particular if a dial up telephone line is used or the Internet connection is very slow the String T O and also the Unit response time out will have to be increased until the values that permit correct reception of the reply of the unit connected are found For connection via serial line the LIN10x peripherals can be connected directly to the COM of the PC in RS232 The RS485 interface is not available on the LIN102 and LIN103 peripherals this parameter is reserved for future developments After con2. PSA Programming Sequence Aid User Manual PSA Programming Sequence Aid User Manual Contents 1 MIE CI OO acteristics nich E EE EE EEE E sade da cg esau cee ane naan ee 2 2 Oprati MOJO eee een mene men ren cane ann eee en eee eee eee 2 MS Cell Atl OUT AE E race E E E E E E E TE E E E E E E 3 4 WS VS CU ONO P Ane A a e A AE EE aA 3 5 Configuration of the peripheral Unit ccccccccssccceseccececsececeeecaueccaueesueeseueeseecsueesageceucesaueesucesueeseeeseesaesaeeas 4 6 COMlGUIAUION Procedur S orenian nnan ia EAEE aE AEEA AEAEE E EAE EEEn EEEE SD 6 1 FOW tO Send command S insisi niaii aa ia E a aE ANAA O NNi 10 SAE aana Cl OC EE E E A A E E A EE E E A EAT 11 Ae aie kee giire E EEEN A P AA A E A T A E TEE E A T A A AE E 12 Ed 1 January 2005 1 ELPRO Video Labs s r l e pro Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 0119348778 FAX 39 0119348779 PSA Programming Sequence Aid User Manual 1 Introduction This manual describes the functions of the 0 1 version under test release of the Programming Sequence Aid PSA SW 2 Operating mode PSA SW is designed to program the relay opening closing commands that are transmitted at a pre established time and date to the units of the LIN10x family A set of commands linked to an annual programming calendar can be defined for each LIN10x unit this association is defined as procedure Therefore a procedure can be considere
3. 00 CLOSE Relay 04 16 00 OPEN Relay O4 30 December 02 January Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Hew Delete Hew Delete _ New Delete _ Delete r Second paia From date To date Working d Festive d 1 August E August aba I Monday Thuesday vvednesd Thursday Friday Saturday Sunday Excluded periods Excluded days 15 August 00 00 11 59 Excluded months Jan Feb Mar Apr May dun dul Aug Sep Oct Nov Dec hh mm Command Dike Command Add parameter Mew Delete Delete Clear All 8 ELPRO Video Labs s r l e pro Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 0119348778 FAX 39 0119348779 PSA Programming Sequence Aid User Manual the second period is defined as follows s Procedure configuration z loj x Procedure name Example procedure isi fear COo Procedure status ACTIVE fish penod From date To date Working d Excluded days 1 January 31 December _ Festive d 01 May 00 00 23 59 Al day Commands for Saco perut M Monday I Tuesday V vWednescd Thursday Achar IY Friday D Saturday Sunday CLOSE Relay 01 Excluded periods Excluded months CLOSE Relay 02 OFEN Relay 01 OFEN Relay 02 30 December 02 January Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Hew Delete Hew Delete _New Delete _ Delete G Sec
4. 7 How to send commands During normal functioning of the program a window is displayed with the list of commands of the day that must be transmitted to the peripheral units Today s date Current time a Procedures 2342 2004 10 40 05 Command List me First command of the list that is to be transmitted 00 12 00 4 a Tet floor control lt C4 gt 01 16 00 A a 1st floor control lt 04 gt view LOG Command string Name of the peripheral unit to which to send the command Procedure status A active D de active Status of the command relating to the day of the week a command active for this day of the week d command not active for this day of the week Time of transmission of the command Progressive number of the command In this list the first command that will be transmitted to peripheral unit is highlighted indication is also provided of whether that command belongs to a procedure that has been de activated with the Procedure status option described above and if the day of the week Monday Tuesday etc is affected by the command In the example the description Aa indicates that the procedure is active and the day is affected by the command as configured for the first period of the procedure provided as example This window manages effective transmission of the commands to the peripheral units and must always be active otherwise execution of the procedures is interrupted Execution can howe
5. transmission the effective time of transmission of the command and the related outcome are also indicated for each command sent In addition to logging the commands transmitted the date and time of execution of the program and any activations and de activations of the procedures are also indicated It is also possible from this window to access the log file in which the last events that have occurred are saved in a circular rile using the LOG File key Close Last record 00004 1000 00001 23771 272004 11 30 31 START form procedure 00002 2371 2 2004 11 30 33 Read procedure file for new day 0000 2371 2 2004 12 00 00 12 00 LN103 Aa 13t floor control C4 OF command sent 0004 4371 22004 16 00 00 16 00 LINT03 Aa Tet floor control lt 04 gt OF command sent This window contains the same information as the previous window but relating to the last 1000 events that have occurred in addition there is only the sequential number of the record of each event As the file is circular the last record written may be in any position of the list 11 ELPRO Video Labs s r l e p go Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 0119348778 FAX 39 0119348779 PSA Programming Sequence Aid User Manual 9 Manual control Commands can be sent manually to the peripheral units configured without affecting functioning of any active procedures To send the commands manually select the peripheral required b
6. unit connected and replies correctly a ao o YELLOW polling of unit in course PY nit name Identifier of the unit connected when it answers the polling Exit Program 6 ELPRO Video Labs s r l e pro Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 0119348778 FAX 39 0119348779 PSA Programming Sequence Aid User Manual To access procedure configuration select the PSA Configuration button in the status window Before proceeding with configuration you will be asked to confirm de activation of any active procedures After confirming de activation another column with the types of units configured is displayed in the status window 51 IND Ox le Terni ation unit Sah F Procedure cogu ation Types of units configured Unit ontiguration SARs ale A a a a te Exit configuration ee orate Erit iragan Any active procedures have been interrupted Clicking on unit type accesses procedure configuration for the unit selected and a window with the list of any procedures configured is displayed Procedure configuration Name of the unit selected Procedures list Jsi ffagar comot Mew proc Edit proc parameters Delete proc Number of procedures configured for the unit E wit E E eae T Total number of procedures configured Total number of procedures p ELPRO Video Labs s r l Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 011934877
7. 348778 FAX 39 0119348779 PSA Programming Sequence Aid User Manual 5 Configuration of the peripheral units This operation must be carried out before configuring the procedures LINTOx To access configuration of the peripheral units select the Unit Configuration button in the status window Communication unit status During configuration operations of the peripheral units and of EE the procedures the part of the program that controls 12 SEE transmission of the commands is de activated This is to avoid the possibility of transmission of commands programmed with a no longer valid configuration or one that must be modified Confirmation of de activation of any active procedures is requested before displaying the peripheral configuration window Unit Configuration P34 Configuration Once de activation of active procedures has been confirmed the window with any units configured is displayed Unit configuration Name and IP address of the PC on which This Computer o mcomputer 127 0 0 1 IG oe ene le Miistaned Mew unit Delete unit Edit unit parameters OK Here you can add cancel or edit the parameters of the peripheral units A new unit is created using the New Unit key 4 ELPRO Video Labs s r l e pro Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 0119348778 FAX 39 0119348779 PSA Programming Sequence Aid User Manual
8. 8 FAX 39 0119348779 PSA Programming Sequence Aid User Manual Here you can add cancel or edit the parameters of the procedures configured for the unit selected with the New Proc key A procedure that complies with the following requirements has been configured in the example below Relay 4 must be closed from 12 00 to 16 00 each working day of the week for the whole year except for mthe month of August mthe period from December 30 to January 2 mMay 1 Also a different type of management is adopted for the month of August Relays 1 and 2 must be closed from 9 00 to 10 00 each Monday of the month except for the first half day of August 15 To obtain this type of behavior a procedure that uses both the periods planned must be configured the 1st period is defined as shown in the figure below Period excluded Month excluded Days excluded Definition of the period of action of the command Definition of the days of the week concerned Commands relating to the first period defined ij Procedure configuration lol x Procedure name E ample procedure fof door coniro Procedure status A T IVE g p First period working d Excluded days From date To date Festive dd oi May 00 00 23 59 4 Januar wl ia Deceme amp 2 l All day Commands for Jaret pena IY Monday If Tuesday M vvednesd i Thursday Attime Action IV Friday Saturday Sufday Escluded periods Excluded months 12
9. d as an annual programmer clock that controls several relays of the same machine In order to send commands to the LIN10x units managed the program must always be active on the PC on which it is installed Similarly the clock and calendar of the PC must be updated with the exact time and date These elements are essential for precise transmission of the commands to the LIN10x The units managed are constantly monitored through periodic polling and any communication errors are displayed in the related window A trace of each command sent towards the peripheral units is maintained in a circular log file in which the effective time of transmission and the result of the operation are recorded It should be noted that as there is no check on the effective status of a relay open or closed following execution of a command only the successful or unsuccessful transmission of the command is recorded Connection of the peripherals Up to 8 LIN10x units can be connected to the Management PC on a serial link RS232 or via a LAN or Internet For connection and configuration of the LIN102 and LIN103 units as indicated above refer to the respective manuals LIN102 user manual LIN103 user manual LIN10x family installation guide all of which can be downloaded from the site www elprovideolabs com Manual control Apart from the procedures configured the LIN10x units can also be controlled manually In this case the status of the relay can be disp
10. e installation procedure is fully guided and the SW is allocated automatically in the ELPRO PLC folder The PC must equipped with the communication interfaces to be used to manage the LIN10x units RS232 or LAN card for local management modem for management via Internet Note Remember that a fixed IP address is necessary for management via Internet and that at the moment no security or authentication protocol is envisaged for access to the remote LIN10x units 4 First execution of PSA The first time the SW is run the work files necessary for management of the LIN10x are initialized and the Reset procedures file message is displayed this must be confirmed with OK and then the initial window This window provides information about the SW release being used To start the program select the START button The two main windows for control and configuration of the LIN10x units and procedures are displayed At this point carry out the following operations in the order indicated e configuration of the peripheral units to be controlled e configuration of the procedures calendar and commands Creation or subsequent modifications of the peripheral units and procedures is followed by a procedure compilation phase in which all the data entered will be correlated in order to create the sequence of commands to be sent each day 3 ELPRO Video Labs s r l e pro Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 0119
11. figuring or modifying the data of the peripheral confirm with OK The new unit will appear in the list of units configured 5 ELPRO Video Labs s r l e pro Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 0119348778 FAX 39 0119348779 PSA Programming Sequence Aid User Manual Unit configuration The name of the unit the type of interface This Computer oemcomputer 127 0 0 1 used and the type of unit are indicated det floor control LAH 192 168 1 200 100111 23119 LIN103 Identifier used by the SW for this LIN10x Mew unit Delete unit Edit unit parameters After configuring or modifying the units to be managed quit this phase with the OK confirmation key Deletion of a peripheral unit using the Delete unit key causes cancellation of all the procedures that have been configured for this On exiting the configuration phase the existing procedures will be recompiled as the data of the units managed have been modified Before configuring the procedures it is good practice to check the status of the connection with the units configured so far with manual management see par 9 Manual control 6 Configuration procedures This operation must be carried out when all the peripheral units managed have been configured correctly LINT0x mm A Coammunic ation unit statis Status of the communication RED error unit not connected fist floor control GREEN
12. layed at any time for each unit and the open close commands can be sent directly These commands will also be recorded in the log file Procedure and calendar Each procedure may consist of two blocks of 16 commands each associated to a calendar These commands must necessarily refer to the relays of the same LIN10x units Several procedures can be associated to each unit A maximum of 100 procedures can be managed Leap years Leap years are managed automatically according to the calendar of the PC i e it is not necessary to indicate any particular behavior for February 29 Summer time The change to Summer time and vice versa is managed automatically e Change from Summer time to solar time clock moved back one hour the commands carried out during the repeated hour are performed once only e Change from solar time to Summer time clock moved forward one hour the commands that are to be performed in the hour skipped are transmitted at the beginning of the new hour Warning for this function the clock of the PC must be configured with the Change automatically to Summer time option activated 2 ELPRO Video Labs s r l e pro Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 0119348778 FAX 39 0119348779 PSA Programming Sequence Aid User Manual 3 Installation The PSA SW must be installed on PCs with Windows 98 or XP operating system The SW occupies around 10 Mbytes of disk space Th
13. ond period From date To date Working d _ Festive d d AUqust AUGUST 1 aus Js aus g E M Monday Thuetday vvednesd Thursday Friday MAT Saturday Sunday Excluded pernod Excluded months Jan Feb Mar Apr May Jun Jul Aug Excluded days 15 August 00 00 11 59 hh mm Command olo Command Add parameter Hew Delete SST E Commands to be sent for the second period Sep Oct Nov Dec Days of the week affected by the commands First 1 2 day excluded Definition of the period of action of the command An option defined with Procedure status is provided for each procedure this can be used to activate or de activate a procedure at any time This may be useful during maintenance of the plant controlled Once you have defined the periods and commands confirm with the OK key The window will be closed and the list with the new updated procedure added will be displayed To end the procedure configuration phase you must also exit from the Procedure configuration window with the EXIT key and then select the Exit Configuration key of the LIN10x main window At this point compilation of the data entered is started at the end of which all the procedures configured will be activated ELPRO Video Labs s r l Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 0119348778 FAX 39 0119348779 PSA Programming Sequence Aid User Manual
14. ver be interrupted with the STOP PSA key in this way manual management of the peripherals is always possible The procedures are re activated by clicking on the box that shows the status of the procedures Procedure Stopped of the LIN10x window Unit Configuration Procedures Stopped Click to re activate execution of the procedures P54 Configuration E sit Program 10 ELPRO Video Labs s r l Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 0119348778 FAX 39 0119348779 PSA Programming Sequence Aid User Manual 8 Command log You can display the command log using the View LOG button in the Procedures window 22 Command Log Sele Activatonot ihe Log File Close Procedures window 2312 2004 11 30 31 START form procedure Reading of the file of eof 4 2004 11 30 33 Read procedure file for new day commands to be sent 2312 2004 12 00 00 12 00 LIN TOS Aa 18t floor control 04 gt OF command sent 2a 12 2004 16 00 00 16 00 LINTOS Aa 1st floor control lt 04 gt OF command sent Commands Result of operation String of the command Name of the peripheral unit Procedure status day Type of unit Scheduled time of transmission of the command Effective time of transmission of the command Date of transmission of the command Only the events that have occurred from the start of execution of the program are listed temporarily in this window In addition to the schedule time of
15. y clicking with the left hand button of the mouse on the unit name in the Status LIN10x window 7 LIN10x Do Unit excluded click with right hand button of the Loammunication unit SH mouse feo CEEE ak ye Second unit gg Click the left hand key to activate manual ee management of the unit wi m ay unit FSA Configuration Exit Program Relay Relay Relay Relay Any commands send manually are recorded in the LOG file A unit can be excluded from periodic polling by clicking with the right hand button of the mouse on the unit name in this case any commands present in the procedures will not be sent and an error condition will be recorded in the log file To re include the unit click again with the right hand button of the mouse 12 ELPRO Video Labs s r l e p go Via della Praia 4 a FERRIERA di BUTTIGLIERA ALTA TO ITALY Tel 39 0119348778 FAX 39 0119348779
Download Pdf Manuals
Related Search