User manual - dunavox.com
Contents
1. Wash the shelves with a mild detergent solution Wring excess water out of the sponge or cloth when cleaning any area of the controls Wash the outside cabinet with warm water and mild liquid detergent Rinse well and wipe dry with a clean soft cloth Do not clean the stainless steel with steel wool pads Suggest to using an all in one stainless steel cleaner to clean the stainless steel and always clean in the direction of grain POWER FAILURE In the event of a power interruption all previous temperature settings are automatically memorized If power is interrupted power surge breaker switch etc and then powered up again the unit will operate with the last temperature set point Most power failures are corrected within a few hours and should not affect the temperature of your appliance if you minimize the number of times the door is opened If the power is going to be off for a longer period of time you need to take the proper steps to protect your contents NOTE Irrespective of the cause if you notice either abnormal temperature or humidity levels inside your unit be reassured that only long and frequent exposure to these abnormal conditions can cause a detrimental effect on your wines VACATION TIME Short holidays Leave the unit in operation for holidays of less than three weeks Long absences If the appliance will not be used for several months remove all items turn off the appliance and unplug Clean an2. The Controls of Your Unit POWER To turn the appliance on off press and hold the O key for 5 seconds until themperature display lights up or goes out NOTE Pressing the ae key once can switch off the audible alarm when the alarm is on LIGHT lt lt Used to turn the inner light on off up F Used to increase warm the set temperature by T OH DOWN w Used to decrease cool the set temperature by 1 C 1 F Display Display the digital indicators temperature and service Indicator Light The indicator light is located at the right lower corner of the display The indicator light will be on when the multi key function is selected To perform the multi key function press and hold the first key then press the rest key for at least 5 seconds and then release all the keys F C Selector Select the temperature display setting in Fahrenheit or Celsius degree To change the temperature from Fahrenheit to Celsius or from Celsius to Fahrenheit press and hold the LIGHT key for 5 seconds Key Lock Only for models with outside controls If in 2 minutes or longer without pressing any key the key lock will be activated automatically To remove the lock press the UP and DOWN keys at the same time for at least 5 seconds and the indicator light will flash three times to confirm the action Setting the Temperature Control e The unit has single temperature zone The temperature can be set between 5 C an
3. e Electrical devices are not toys Always keep the device out of the reach of children Keep the mains cord out of the reach of children Do not let the mains cord hang over the edge of the table or worktop on which the appliance stands e To protect against the risk of electric shock DO NOT IMMERSE the unit cord or plug in water or spray any other liquid e Unplug the appliance from the plug socket when not in use when moving from one location to another and before cleaning e To disconnect the appliance grip the plug and pull it from the wall outlet Never pull by the cord e WARNING Please keep the appliance away from substance which can cause ignition Do not operate the appliance in the presence of explosive and or flammable fumes e Do not place the appliance or any of its part near an open flame cooking or other heating appliance Code Rev D 20140818 IEC Do not operate the appliance with a damage cord or plug if the product malfunctions or if it is dropped or damaged in any manner If the supply cord is damaged it must be replaced by the manufacturer or an authorized service centre or similarly qualified persons in order to avoid a hazard The use of attachments not recommended by the manufacturer may be hazardous Place the unit on a dry level surface Do not operate if the housing is removed or damaged A loose fit between the AC outlet receptacle and plug may cause overheating and a distort
4. handle installation 2 Install the handle 4 tightly as shown above with two screws 2 3 and flat washers 2 2 provided 3 Replace the door gasket Code Rev D 20140818 IEC REVERSING THE DOOR HINGE It is possible to reverse the door on this appliance if required To do so follow the steps below Note All parts removed must be saved to do the reinstallation of door DESIGN 1 For built under models 1 2 3 3m 1 Remove the ventilation grille 0 2 and the adjustable ventilation grille O 1 by unscrewing the screws 3 amp Q4 Fig 1 NOTE For some models without adjustable ventilation grille the step is not needed 2 Remove the bottom hinge O 5 by unscrewing the four lock screws 2 6 Be careful to hold the glass door firmly after removing the screws Fig 2 3 Gently pull down to remove the glass door from the right top hinge and place it on a padded surface to avoid the risk of damage Then remove the right top hinge Q 9 Fig 4 4 Unscrew and transfer hinge pin O 7 and or door stopper 80f the bottom hinge to the opposite side Fig 3 5 Pop out the cover caps on the left side of cabinet and use them to cover the screw holes on the right hand side 6 Screw the alternative left top hinge O1 included in the fittings on the left hand side of cabinet
5. of a fan fans and the hollow shelves NOTE Frost may be accumulated on the evaporator if the unit is repeatedly opened in a high heat or high humidity location If this frost pattern does not clear within 24 hours your unit will require manual defrosting WINE SERVING TEMPERATURE CHART All wines mature at the same temperature which is a constant temperature set between 11 C to 14 C The below chart is an indicative temperature chart to indicate the best temperature for drinking purposes le e fs Spumante Bae emen s 4 Blanc Champagne Vintage Dry White Chardonnay Dry White Gew rztraminer al a 10 50 Riesling Pinot grigio Sweet White Sauternes Barsac Montbazillac Ice Wine 10 50 Late Harvest 55 71 55 Code Rev D 20140818 IEC 15 Sauternes Cabernet amp Merlot French aja 20 Australian New Zealand Chilean Italian Spanish Californian Argentinean Room temperature not exceeding 20 C 68 F Vintage Bordeaux IMPORTANT INFORMATION ABOUT TEMPERATURE Your unit has been designed to guarantee optimum conditions for storing and or serving your wines Fine wines require long and gentle developments and need specific conditions in which to reach their full potential All wines mature at the same temperature which is a constant temperature set between 11 C to 14 C Only the temperature of d gustation wine appreciation varies according to the type o
6. settings of MIDDLE temperature zone are adjustable with the range 5 11 C 41 52 F The preset temperature at the factory is 8 C 46 F e The temperature settings of LOWER temperature zone are adjustable with the range 11 138 C 52 56 F The preset temperature at the factory is 12 C 54 F e Temperature control for UPPER and MIDDLE temperature zones is at upper control unit Temperature control for LOWER temperature zone is at lower control unit e When you press the two keys at the first time the display will show the last temperature set previously The temperature will increase 1 C or 1 F if you press the UP key once on the contrary the temperature will decrease 1 C or 1 F if you press the DOWN key once The display flashes while you make the setting e After the temperature has been set the display shows the current inner temperature of the particular temperature zone e To view the set temperature at any time press the UP or DOWN key the set temperature will temporarily flash in the display for 5 seconds Then the display shows the current inner temperature again TEMPERATURE DISPLAY During normal operation the temperature display on the control panel shows the temperature inside the appliance The temperature display will flash if A different temperature is being set The temperature in the zone deviates by more than 5 C from the set temperature The temperature display flashing ensur
7. then the temperature has risen higher or fallen lower than the temperature that has been set This could be due to The appliance door being opened too often The ventilation opening being covered or too dusty A lengthy interruption to the power supply A large amount of bottles has been added to the unit The display temperature is out of the range If yes close the door Do not open the door more often than necessary Clear the obstructions and clean the dust Leave the appliance to work for a while until the set temperature has been reached Only temperatures within the range 0 99 F 9 37 C the appliance can display will be shown If the temperature is not within this range the icon will be displayed instead That is normal 5 The icon is lit up and flashing in the temperature display WARRANTY The statutory warranty period applies If the product is defective please contact your local distributor In case you need any services please include the following documents when you send in the device e A copy of the receipt with purchasing date e Areason for the claim or description of the fault The warranty does not cover 1 Damage in transit or when moving the appliance 2 Any damages caused from negligence accident improper use improper installation service or use for purposes other than those described in the instruction manual Damage caused by connecting your product to th
8. DUNAVOX WINE CABINET INSTRUCTION MANUAL Model DAU 17 57DB DAU 17 57DSS DAU 36 80DB DAB 36 80DSS DX 89 215BDBK DX 89 215BSDSK DX 171 430PK IMPORTANT SAFEGUARDS DISPOSAL CONNECTION TO THE MAINS SUPPLY PRODUCT FEATURES INSTALLATION OPERATING YOUR APPLIANCE CARE AND MAINTENANCE TROUBLESHOOTING GUIDE WARRANTY CE Please read this manual carefully before installing and starting up and store it in a safe place If you pass on the product to another person hand over this instruction manual along with it IMPORTANT SAFEGUARDS When using an electrical appliance basic precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following FOR YOUR SAFETY Read all instructions carefully even if you are quite familiar with the appliance e The appliance is intended to be used for the storage of wine Use this appliance only as described in this manual Other uses not recommended may cause fire electric shock or personal injury his appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision
9. Fig 4 7 Unscrew and transfer the holes cover O 12 and lock catch 3 to the opposite side of glass door Only for models with lock on the ventilation grille Fig 5 8 Rotate the door 180 No need for models with lock on the door and relocate the door to the designated position Then screw the bottom hinge assembly on the left designated position and tighten it after the door is leveled Transfer the handles amp plugs to the opposite positions and then reassembly the ventilation grilles if need DESIGN 2 For fully integrated models 1 T E il n 1 e j I l f S Dr loc gt Oum Remove the glass door by unscrewing the eight lock screws 5 3 and 4 Be careful to hold the glass door firmly after removing the screws and place it on a padded surface to avoid the risk of damage Unscrew and transfer the door supporter Q2 to the opposite side Rotate the glass door 180 and refit the glass door to the opposite side Then screw and tighten it after the door is leveled DESIGN 3 For tall models Pop out the cover caps on the left side of cabinet and use them to cover the screw holes on the right hand side Screw the alternative left top hinge 8 included in the fittings on the left hand side of cabinet Fig 4 Unscrew and transfer door supporter C 10 to the opposite side At the same time remove the stopper
10. Unit Lower Control Unit POWER To turn the appliance on off press and hold the key for 5 seconds until themperature display lights up or goes out NOTE Pressing the CO key once can switch off the audible alarm when the alarm is on LIGHT Used to turn the inner light on off up Used to increase warm the set temperature by 1 C or 1 F DOWN w Used to decrease cool the set temperature by 1 C or 1 F Display Display the digital temperature and service indicators H is for UPPER temperature zone m is for MIDDLE temperature zone and is for LOWER temperature zone Indicator Light The indicator light is located at the right lower corner of the display The indicator light will be on when the multi key function is selected To perform the multi key function press and hold the first key then press the rest key for at least 5 seconds and then release all the keys F C Selector Select the temperature display setting in Fahrenheit or Celsius degree To change the temperature from Fahrenheit to Celsius or from Celsius to Fahrenheit press and hold the LIGHT key for 5 seconds Setting the Temperature Control e The unit has three temperature zones The temperature of all zones can be set separately e The temperature settings of UPPER temperature zone are adjustable with the range 11 22 C 52 72 F The preset temperature at the factory is 18 C 65 F e The temperature
11. als the installed unit almost completely so an air vent must be provided in the base of the housing Warmed air must be conducted via the ventilation shaft to the rear wall of the housing and then expelled upwards The ventilation channels should measure at least 200 square centimeters in cross section gt Lowe e i x ka L E i E _ 6 a e inl K f t A B A mm B mm C mm Du pe e W uS FA AE EEE WEN M Remark The dimension A does not include the adjustable legs and the units are permitted to be installed without the adjustable legs WARNING To ensure the proper functioning of the appliance air vents should never be blocked or covered Code Rev D 20140818 IEC BUILT IN CABINETRY INSTRUCTIONS Make sure your installation does not block the front ventilation grille And be sure the door will open and close properly in the chosen location M nis E BE n nu m mE qi A mm Bim D m 100 125 1772 550 BENE 170 1772 660 1768 680 ELECTRICAL CONNECTION WARNING Improper use of the grounded plug can result in the risk of electrical shock If the power cord is damaged have it replaced by a qualified electrician or an authorized service center All electrical work should be carried out by a suitably qualified and competent person in accordance with local and national safety regulations Check that the voltage mark
12. and to the health of your fellow human beings Improper disposal endangers health and the environment Further information about the recycling of the product may be obtained from your town hall refuse collection department or the store where you purchased the product CONNECTION TO THE MAINS SUPPLY UK IRL HK SINGAPORE Check that the voltage marked on the product corresponds with your supply voltage This product is fitted with a 13A plug complying with BS1363 If this plug is unsuitable or needs to be replaced please note the following WARNING THIS APPLIANCE MUST BE EARTHED Important The wires in the mains lead are coloured in accordance with the following code GREEN YELLOW EARTH BLUE NEUTRAL BROWN LIVE Earth Green Yellow N Ns ER Neutral Blue This appliance is equipped with a plug fitted with a 13 amp fuse Should the fuse fail then it must be replaced with an ASTA approved fuse conforming to BS1362 of the same rating If you need to replace the plug or if the plug is of the incorrect type for your socket remove it and replace it with an appropriate type Dispose of the old plug safely As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The GREEN YELLOW wire is the EARTH and must be connected to the terminal whic
13. ar non retail applications e Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this manual All other servicing should be referred to a qualified technician e Replace all panels after service before operating e Use two or more people to move and install the appliance Failure to do so can result in back or other injury e Never clean appliance parts with flammable fluids These fumes can create a fire hazard or explosion And do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance The fumes can create a fire hazard or explosion e Do not connect or disconnect the electric plug when your hands are wet e t is recommended that a separate circuit serving only your appliance be provided Use receptacles that cannot be turned off by a switch or pull chain e f you have a lockable appliance do not keep the key near the appliance or within reach of children Code Rev D 20140818 IEC WARNING To reduce the risk of fire electric shock or personal injury unplug or disconnect the appliance from the power supply before servicing SAVE THESE INSTRUCTIONS If you are experiencing problems check the Troubleshooting Guide at the back of this manual It lists causes of minor operating problems that you can correct by yourself DISPOSAL Dispose of your appliance packaging properly Ensure that any plast
14. d 22 C 41 F and 72 F which is ideal for storing red white or sparkling wine e When the unit is plugged in for the first time the unit will power up automatically to the preset defaults The temperature preset at the factory is 12 C 54 F e You can set the temperature as required by pressing the UP or DOWN key When you press the two keys at the first time the display will show the last temperature set previously The temperature will increase 1 C 1 F if you press the UP key once or the temperature will decrease 1 C 1 F if you press the DOWN key once The display flashes while you make the setting e After the temperature has been set the display shows the current inner temperature e To view the set temperature at any time press the UP or DOWN key the set temperature will temporarily flash in the display for 5 seconds Code Rev D 20140818 IEC 11 Then the display shows the current inner temperature again USE AND CONTROL DUAL ZONE The Controls of Your Unit POWER To turn the appliance on off press and hold the O key for 5 seconds until themperature display lights up or goes out NOTE Pressing the O key once can switch off the audible alarm when the alarm is on up F To increase warm the set temperature by 1 C or TAE DOWN w To decrease cool the set temperature by 1 C or 1 F LIGHT Used to turn the inner light on off Display Display the digital temperatu
15. d dry the interior thoroughly To prevent odour and mold growth leave the door open slightly blocking it open if necessary MOVING YOUR APPLIANCE Unplug the power plug from the electrical outlet Remove the contents from the racks and all moving parts from inside Raise the adjustable legs up to the base to avoid damage Code Rev D 20140818 IEC 17 Tape the door shut and lock it if with a lock system Transport the wine cellar only in the upright position Also protect the outside of the appliance with a blanket or similar item ENERGY SAVING TIPS Should the unit be left empty for long periods of time it is suggested that the appliance is unplugged and after careful cleaning leave the door ajar to allow air to circulate inside the cabinet in order to avoid possible condensation mold or odors forming The appliance should be installed in the coolest area of the room away from heat producing appliances and out of the direct sunlight Ensure that the unit is adequately ventilated Never cover air vents Clean dust and dirt from the condenser at regular intervals Only open the door for as long as necessary and for as short a time as possible Store the content in an organised way Do not over fill the appliance to allow air to circulate PROBLEMS WITH YOUR APPLIANCE You can solve many common problems easily saving you the cost of a possible service call Try the suggestions below to see if you can s
16. ding on your model Continuously variable electronic temperature control with digital display and touchpad input Temperature can be set from 5 to 22 C 40 to 72 F for either compartment and can be displayed in either Fahrenheit or Celsius degree Can be set to the long time storage maturing temperature or a specific serving temperature for red white sparkling wines Cooling and Heating to maintain the perfect storaging and or service condition Dynamic compressor type cooling to ensure interior air circulation with even distribution of temperature and humidity Soft white LED Interior Light with ON OFF switch Function mode and Showcase mode Open door and malfunction warning system Sabbath mode will allow the lights to remain off during certain religious observances Temperature memory function If power is interrupted power surge breaker switch etc and then powered up again the unit will operate with the last temperature set point Automatic defrosting with defrost water evaporation Reversible tempered double triple pane smoked glass door protects your wine from UV light and creates an attractive display with few condensation and low noise Black coated matte steel outer frame and black plastic interior liner offer lifetime performance and stability The black liner prevents excessive light from damaging the maturity process Optional stainless steel framed glass door with stainless steel handle Optional roll
17. e display continues to flash until the set temperature has been reached The display then lights up constantly and the alarm system is fully active again INTERIOR LIGHT The interior light makes it easy to view your wine labels and enhances the display of your collection Touching the LIGHT mark toggles between 2 modes of operation for the internal lights functional default mode and showcase mode If you are in functional default mode the lights will turn on only when the door is open If you are in showcase mode the lights will be on whether or not the door is open The unit is equipped with a LED light fitting system To change the LED light fitting pls contact the service department NOTE Please use only the original LED light fittings provided by the manufacturer BOTTLE RACKS AND STORAGE WARNING Do not pull out more than one loaded shelf at a time as this may cause the unit to tilt forward WARNING Do not try to slide the shelves outwards beyond the fixed position to prevent the bottles from falling WARNING To prevent damaging the door gasket make sure the door is fully open when pulling shelves out of the compartment All the wine racks slide out for easy access except for the bottom shelf For easy access to the bottles stored pull the rack out gently until it stops The shelves are designed with an emergency stop to prevent them being removed too far when loaded Many bottles may differ in size and d
18. e the unit will power up automatically to the preset defaults The preset temperature at the factory for UPPER LEFT temperature zone is 10 C 50 F and for LOWER RIGHT temperature zone is 16 C 60 F e You can press the left side UP and DOWN keys to control the internal temperature of the UPPER LEFT temperature zone and press the right side UP and DOWN keys to control the internal temperature of the LOWER RIGHT temperature zone When you press the two keys at the first time the display will show the last temperature set previously e IMPORTANT The temperature set for the LOWER temperature zone must always be just as high or higher than that in the UPPER temperature zone For optimal performance the set temperature of the two zones should differ by at least 4 C e The temperature that you desire to set will increase 1 C or 1 F if you press the UP mark once on the contrary the temperature will decrease 1 C or 1 F if you press the DOWN mark once The display flashes while you make the setting e After the temperature has been set the display shows the current inner temperature of the particular temperature zone e To view the set temperature at any time press the UP or DOWN key the set temperature will temporarily flash in the display for 5 seconds Then the display shows the current inner temperature again Code Rev D 20140818 IEC 12 USE AND CONTROL THREE ZONE The Controls of Your Unit Upper Control
19. e wrong power source Damage from power failure Faulty installation or modification made during installation Damage caused by unauthorized repair Any damages resulting from force majeure fire disaster or natural disaster Alterations to the product without express permission from the manufacturer Parts such as light removable shelves or plastic Se ice AR cer X9 0 Any spoilage or damage to wines or any other contents incidental or consequential to possible defects of the unit NOTE The warranty clauses and specifications are subject to change without notice Code Rev D 20140818 IEC 19
20. ed on the product corresponds with your supply voltage Connect this appliance to a separate at least 13A circuit Connection should be made via a suitable switched Socket which is easily accessible For extra safety it is advisable to install a residual current device RCD with a trip current of 30mA Have the receptacle and the circuit checked by a qualified electrician to ensure that the socket is grounded correctly Note n locations where there is frequent lightning it is advisable to use surge protectors Do not connect the appliance to the mains electricity supply by an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating The appliance must not be connected to an inverter and must not be used with a plug adapter as these can cause damage to the appliance s electronic unit The cord must rest securely behind the appliance and not be allowed to lie or hang unprotected WARNING THIS APPLIANCE MUST BE EARTHED INSTALLING THE HANDLE IMPORTANT Do not overtighten the screws amp do not use power tools to install the handle DESIGN 1 Locate the handle C 1 over the fixing pins 3 of the door and using the supplied allen key tighten the securing grub screws 2 to fix the handle DESIGN 2 1 Remove the door gasket 1 on the side you wish to install the handle you can see two designated holes for
21. es that the temperature can not rise or fall un noticed and impair the wine TEMPERATURE MEMORY FUNCTION In the event of a power interruption power surge breaker switch etc the unit remembers the previous temperature settings When the power is recovered the cabinet temperature will go back the same setting temperature as before the power interruption TEMPERATURE ALARM An alarm will sound if the temperature in one of the zones rises or falls outside the temperature range Code Rev D 20140818 IEC 13 The relevant temperature display will flash at the same time The temperature the appliance is set at determines the temperature the appliance recognises as being too warm or too cool The alarm will sound and the temperature display will flash When you switch the appliance on if the temperature inside the appliance is very different from the temperature set When there has been a lengthy interruption to the power supply When too many items have been put into the unit at one time When the door is not closed tightly DOOR ALARM If the door has been left open for more than 60 seconds the alarm will sound Once the set temperature has been reached in the appliance the alarm stops and the relevant temperature display stops flashing However if the noise disturbs you you can switch the alarm off before this if you wish by pressing the POWER key once The alarm will stop The relevant temperatur
22. f glass door This condensation will disappear when humidity levels drop For prevention it is advisable to install the appliance with sufficient ventilation in a dry and or an air conditioned place NOTE The appliance must be positioned so that the plug is accessible BUILT UNDER INSTRUCTIONS Make sure your installation does not block the front ventilation grille The unit is designed to fit under worktops between 820 and 890mm in height using the adjustable ventilation grille to ensure that the feet are concealed from front view Remove the adjustable ventilation grille screws and slide it to the required height Tighten the screws to lock the grille in position If the unit is fully integrated to be installed for fitting kitchen plinth make sure that the ventilation gaps in the plinth are at least 300 square centimeters and remove the ventilation grilles so that warm air can disperse unhindered Otherwise the appliance has to work harder resulting in an increase in electricity consumption NOTE When pushing the appliance into the niche make sure that the mains cable does not get trapped 715 720 Code Rev D 20140818 IEC 865 B mm mm mm 295 300 110 460 595 ludi 110 460 A mm B mm C mm 37 5cm 375 380 495 wie S mom 60cm 595 610 520 we ju P FULLY INTERGRATED BUILT IN COLUMN INSTRUCTIONS The unit door se
23. f wines see Wine Serving Temperature Chart above This being said and as it is for natural cellars used by wine producers for long period of storage it is not the exact temperature that is important but its consistency In other words as long as the temperature of your wine cellar is constant between 11 C to 14 C your wines will be stored in perfect conditions Not all wines will improve over the years Some should be consumed at an early stage 2 to 3 years while others have tremendous ageing capability 50 and over All wines have a peak in maturity Do check with your wine merchant to get the relevant information CARE AND MAINTENANCE WARNING Failure to unplug the appliance during service and cleaning could result in electrical shock or other personal injury REMOVING SHELVES To remove any of the shelves from the rail compartment move the shelf to the position where the notch of wooden shelf is exactly under the plastic post and then lift it up and out In order to replace the shelf repeat steps described above in reverse And make sure to engage the shelves with the small pegs of the extended rails when the model is equipped with roller system HUMIDITY CONTROL The appliance is equipped with a system for maintaining the correct level of humidity Under extremely dry environmental conditions you may have to add some water into the humidity box provided with your wine cellar Fill the small pla
24. h is marked with the letter E or by the earth symbol or coloured GREEN or GREEN YELLOW The BLUE wire is the NEUTRAL and must be connected to the terminal which is marked with the letter N or coloured BLACK The BROWN wire is the LIVE wire and must be connected to the terminal which is marked with the Letter L or coloured RED Always ensure that the plug cord grip is fastened correctly Code Rev D 20140818 IEC If in doubt consult a qualified electrician who will be pleased to do this for you This product conforms to EC Directive 92 31 EEC with respect to Electromagnetic Compatibility NON REWIREABLE MAINS PLUG If your appliance is supplied with a non rewireable plug fitted to the mains lead you will find that it incorporates a fuse the value of which is indicated either on the base of the plug or on the fuse carrier Should the fuse need replacing you must use an ASTA approved one conforming to BS1362 of the same rating If the fuse cover is lost the plug must not be used until a replacement is obtained from an electrical supplier If you need to remove the plug cut it from the mains lead and immediately dispose of it Never attempt to re use this plug or insert it into a socket outlet as there is a very great risk of an electric shock N cc X DANGER c i Electric Shock Risk PRODUCT FEATURES Built in or Free standing installation with single dual or three temperature zone depen
25. ic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation Refrigeration equipment must be properly disposed of in a professional and appropriate way in accordance with the current local regulations and laws which protects the environment this applies to your old appliance and to your new unit once it has reached the end of its service life WARNING Please ensure that old worn appliances are rendered unusable before disposal by removing the doors removing the plug cutting the network cable and removing or destroying any snap fastenings or bolts You will thus prevent children from locking themselves in the appliance during play risk of suffocation or endangering their lives in any other way DO NOT dispose of the appliance in landfill as the insulation Cyclopentane and refrigerant gas R600a contained in these appliances are flammable Disposal instructions e The appliance must not be disposed of in the dustbin or with normal household rubbish e The coolant circuit particularly the heat exchanger at the back bottom of the unit must not be damaged F e The symbol on the product or its packaging indicates that this product is not to be handled as normal household waste but is to be taken to a recycling collection point for electrical and electronic goods By correctly disposing of this product you are contributing to the protection of the environment
26. imensions As such the actual number of bottles you may be able to store may vary Bottle capacities are approximate maximums when storing traditional Bordeaux 750 ML bottles and include bulk storage You may load your wine bottles in single row or by stacking while taking note of the following if you do not have enough bottles to fill your wine cellar it is better to distribute the load throughout the wine cellar so as to avoid all on top or all below type loads Do remove or relocate adjustable wooden racks to accommodate larger type of bottles or increase the capacity of the cellar by stacking the bottles up when necessary See removing shelves Keep small gaps between the walls and the bottles to allow air circulation Like an underground cellar air circulation is important to prevent mould and promote a better homogeneous temperature Do not over load your wine cellar to facilitate air circulation Lay the bottles flat Avoid obstructing the internal fans located inside on the back panel of the unit Do not cross contaminate Store only wine in your unit to ensure that the environment is odor free Only store wine in unopened bottles Storing opened bottles may result in spillage DYNAMIC CLIMATE SILENT MODE This Dynamic Climate mode enables the relative humidity inside the unit and the temperature to be distributed evenly around the interior so you can store all your wine under exactly the
27. ion of the plug Contact a qualified electrician to replace loose or worn outlet Locate the unit away from direct sunlight and sources of heat stove heater radiator etc WARNING This appliance is CFC and HFC free and contains small quantities of Isobutane R600a which is environmentally friendly but flammable It does not damage the ozone layer nor does it increase the greenhouse effect Care must be taken during transportation and setting up of the appliance that no parts of the cooling system are damaged Leaking coolant can ignite and may damage the eyes In the event of any damage Avoid open flames and anything which creates a spark Disconnect from the mains Air the room in which the appliance is located for several minutes and Contact the Service Department for advice The more coolant there is in an appliance the larger the room it should be installed in In the event of a leakage if the appliance is in a small room there is the danger of combustible gases building up For every 8 g of coolant at least 1 cubic meter of room space is required The amount of coolant in the appliance is stated on the data plate inside the appliance lt is hazardous for anyone other than an Authorised Service Person to carry out servicing or repairs to this appliance In Queensland of Australia the authorized person must hold a Gas Work Authorisation for hydrocarbon refrigerants before carrying out servicing o
28. lass door from the middle hinge and place it on a padded surface to avoid the risk of damage Fig 1 Unscrew and transfer the door adapter OA and 7 to the designated opposite position of lower glass door Fig 2 Remove the door adapter Q 14 by unscrewing the two lock screws O13 Be careful to hold the upper glass door firmly after removing the screws And then gently pull down to remove the upper glass door 15 from the top hinge and place it on a padded surface to avoid the risk of damage Then remove the right top hinge O10 Fig 5 amp 4 4 Unscrew and transfer the middle hinge O12 and the middle fixing plate O 11 to the opposite position Fig 5 5 Pop out the cover caps on the left side of cabinet and use them to cover the screw holes on the right hand side 6 Screw the alternative left top hinge O9 included in the fittings on the left hand side of cabinet Fig 4 7 Relocate the door adapter O14 on the middle hinge 8 Set the upper glass door to the designated position and install the two lock screws to connect the door adapter O14 with the upper glass door and tighten them before the door is leveled 9 Set the lower glass door to the designated position and reassemble the bottom hinge 10 Recheck and adjust the lower door alignment by loosening the screws C 5 amp C 6 and moving the door adapter C 4 amp Q 7 Tighten the screws 0 5 amp C 6 after the door is le
29. not The circuit breaker tripped or a blown fuse Switch on circuit breaker or work replace fuse The light was switched off on the control Switch on the light panel The rattling noise may come from the flow of the refrigerant which is normal As each cycle ends you may hear gurgling sounds caused by the flow of refrigerant in your The appliance appliance seems to make too If temperature fluctuations occur the contraction and expansion of the inner walls may much noise cause popping and cracking noises The appliance is not properly level e Level the appliance with the adjustable feet The door was reversed and not properly Check the door hinge and installed reassemble correctly The gasket is dirty Clean the door gasket The shelves are out of position Check the shelves and refit correctly EO indicates the communication error for 3 Call for service Display EO E1 zone models E2 E38 EA E1 or E2 indicates that the air E5 E6 or E7 temperature sensor is failed E3 or E4 indicates that the defrost The door will not close properly Code Rev D 20140818 IEC 18 The alarm sounds and the temperature display flashes sensor in the evaporator is failed E5 indicates the defrost heater failure E6 indicates the solenoid valve failure E7 indicates the door switch failure Has the appliance door been open for longer than 60 seconds If not
30. olve the problem before calling customer service TROUBLESHOOTING GUIDE Appliance is not connected to a power e Connect the appliance supply The appliance is turned off e Switch on the appliance The circuit breaker tripped or a blown fuse Switch on circuit breaker or replace fuse The temperature is not set correctly Check the set temperature The ambient temperature could require a Set a higher temperature higher temperature setting The door was opened too often Do not open the door more often than necessary Appliance is not The door was not closed completely Close door properly cold enough Door is not hermetically sealed Check the door seal and clean or replace The condenser is too dirty Clean the condenser when necessary The ventilation opening is blocked or too Clear the obstructions and clean dusty the dust The room temperature is higher than Put the appliance in a cooler average place A large amount of bottles has been added to Leave the appliance to work for a the unit while until the set temperature has been reached The door is open too often Do not open the door more often than necessary The door is not closed completely Close door properly The door gasket does not seal properly Check the door seal and clean or replace Appliance does not operate Appliance turns itself on and off frequently Appliance is not connected to a power Connect the appliance supply The light does
31. oor use only WARNING Do no install the appliance in the laundry Avoid locating the unit in damp areas Place your appliance on a floor that is strong enough to support it when it is fully loaded To level your unit adjust the front leveling leg at the bottom of the unit For freestanding installation 100mm of space between the back and sides of the unit are suggested which allows the proper air circulation to cool the compressor and condenser for energy saving Even for built in installation it is a must to keep 5mm space on each side and at the top to ensure proper service access and ventilation Take care that the air vent at the front of the appliance must never be covered or blocked in any way Locate the unit away from direct sunlight and sources of heat stove heater radiator etc Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption Extreme cold ambient temperatures may also cause the unit not to perform properly Plug the unit into an exclusive easily accessible plug socket Any questions concerning power and or earthing should be directed towards a qualified electrician or an authorized products service centre e he appliance must be installed to all electrical plumbing water and drain connections in accordance with state and local codes e IMPORTANT HIGH HUMIDITY CLIMATE During periods of high humidity some condensation may appear on outside surfaces o
32. out and adjustable solid varnished beech shelves allow for maximum convenience and flexibility to accommodate various size bottles Environmentally friendly refrigerant and foaming insulation gas Optional security lock system with keys Optional humidity control system Humidity Box Optional active charcoal air filter NOTE Features and specifications are subject to change without notice Code Rev D 20140818 IEC INSTALLATION BEFORE USING YOUR APPLIANCE Remove all exterior and interior packing Clean the interior surface with lukewarm water using a soft cloth The unit may have residual odors at first they will disappear as the unit cools Before connecting the appliance to the power source let it stand upright for at least 24 hours This will reduce the possibility of a malfunction in the cooling system caused by handling during transportation During this time we recommend that you leave the door open to clear any residual odors The door on this appliance can be opened from either the left or the right side The unit is delivered with the door opening on the left side Should you wish to open the door from the right follow the instructions Reversing the door hinge Install the handle on the door if necessary INSTALLATION OF YOUR APPLIANCE The appliances are designed to be built in or recessed or free standing installation WARNING Do not store or install the appliance outdoors The unit is for ind
33. pin O 7 of bottom hinge to the opposite designated position or unscrew and transfer the hinge pin 7a of bottom hinge to the opposite designated position Fig 5 amp 3 Unscrew and transfer the door adapter 5 and lock catch OA to the top designated position of glass door Fig 2 Rotate the door 180 and relocate the glass door to the designated position Then screw the bottom hinge on the left designated position and tighten it Fig 5 Recheck and adjust the door alignment by loosening the screws 6and moving the door adapter O 5 Tighten the screws O 6 after the door is levelled Fig 5 DESIGN 4 For double door models 8 3 7 Da O E r 21 9065 3 M g B SUF it __ tk di ES A 42 43 415 Remove the bottom hinge Q1 by unscrewing the four lock screws O 2 Be careful to hold the glass door firmly after removing the screws Fig 1 Gently pull down to remove the glass door from the right top hinge and place it on a padded surface to avoid the risk of damage Then remove the right top hinge O 9 Fig 4 Code Rev D 20140818 IEC Remove the bottom hinge O1 by unscrewing the four screws O2 Be careful to hold the lower glass door Q 3 firmly after removing the screws And then gently pull down to remove the lower g
34. r repairs which involve the removal of covers WARNING Keep ventilation openings in the appliance enclosure or in the built in structure clear of obstruction No liability will be accepted for any damage incurred owing to misuse of the appliance or as a result of repairs carried out by unqualified personnel In this case neither the guarantee nor any other liability claims will apply WARNING Do not use mechanical devices or other means to accelerate the defrosting process other than those recommended by the manufacturer e WARNING Do not damage the refrigerant circuit Never use an appliance with a damaged circuit e WARNING Do not use any electrical appliance inside the food storage compartment of the appliance unless they are of the type recommended by the manufacturer e WARNING To avoid a hazard due to instability of the appliance it must be fixed in accordance with the instructions e CAUTION Please keep the products away from the fire or similar glowing substance before you dispose the refrigerator e Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance e This appliance is intended to be used in household and similar applications such as Staff kitchen areas in shops offices and other working environments farm houses and by clients in hotels motels and other residential type environments bedand breakfast type environments catering and simil
35. re and service indicators Pis for UPPER temperature zone and Wis for LOWER temperature zone l is for LEFT temperature zone and E is tor RIGHT temperature zone Indicator Light The indicator light is located at the right lower corner of the display The indicator light will be on when the multi key function is selected To perform the multi key function press and hold the first key then press the rest key for at least 5 seconds and then release all the keys F C Selector Select the temperature display setting in Fahrenheit or Celsius degree To change the temperature from Fahrenheit to Celsius or from Celsius to Fahrenheit press and hold the LIGHT key for 5 seconds Key Lock Only for models with outside controls If in 2 minutes or longer without touching any key the key lock will be activated automatically To remove the lock press the UP and DOWN keys at the same time for at least 5 seconds and the indicator light will flash three times to confirm the action Setting the Temperature Control e The unit has two separate temperature zones The temperature of both zones can be set between 5 C and 22 C 41 F and 72 F The LOWER RIGHT temperature zone is ideal for storing white and red wine at a setting of 13 C to 22 C 55 F to 72 F The UPPER LEFT temperature zone is suitable for storing champagne and white wine at a setting of 5 C to 13 C 41 F to 55 F e When the unit is plugged in for the first tim
36. rniture or with other tubing Where the unit is installed in open plan kitchen or in partition walls the level of operating noise will be heard more acutely However this is due to the surrounding architecture and not to the unit An individual s perception of noise is directly linked to the environment in which the unit is located as well the specific type of models Our appliances are in line with international standards for such appliance and in line with the latest technical developments But please remember that the noise of the compressor and the coolant circulating in the system is unavoidable DEFROSTING HYGROMETRY VENTILATION Your unit is designed with an automatic defrost system During the Off cycle the evaporator behind the rear wall of the unit defrosts automatically The condensate collects in the drain trough behind the rear wall of the unit and part of it flows through the drainage hole into the drip tray by above the compressor The heat is transferred from the discharge pipe or compressor and evaporates any condensation that has collected in the tray Part of the remaining water is collected within the unit for humidity purposes This system enables the creation of the correct humidity level inside your unit required by the natural cork to maintain a long lasting seal The appliance is not totally sealed fresh air admission is permitted through the drainpipe Air is circulated through the unit by means
37. same excellent conditions If you would like to use the unit to store wine long term the dynamic climate mode is a must This will create a continuous climate in the cabinet which imitates that of a wine cellar In the Dynamic Climate mode the interior fan circulates the inside air evenly even the set temperature is reached Dynamic Climate mode is NOT the factory preset mode because of creating noises and more energy consumption To change to Dynamic Climate mode touch and hold the DOWN key for approximately five seconds The wine cellar will beep five times to confirm Dynamic Climate mode is on To change back to default Silent mode Also named as energy saving mode touch and hold the UP key for approximately five seconds The wine cellar will beep three times to confirm Code Rev D 20140818 IEC 14 default Silent mode is on SABBATH MODE Sabbath mode is available for the observance of certain religious holidays This mode turns off the displays interior light and audible alarms and prevents them from turning on again Normal cooling operations will still take place To initiate Sabbath mode press the POWER and LIGHT keys at the same time for at least 5 seconds The indicator light will flash four times and confirm the Sabbath mode is ON Sabbath mode can be exited by repeating the above process The Sabbath Mode will automatically exit after 96 hours ECO DEMO MODE Eco Demo mode can be activated by presenting
38. stic reservoir humidity box full with water and fit onto the runners found on the top shelf of the appliance Check the water level regularly and refill as necessary Please ensure the reservoir is positioned correctly on the runners on the top shelf to avoid the possibility of water spillage ACTIVE CHARCOAL AIR FILTER The active charcoal air filter is located in the back of compartment Replace it with a new one once a year It can be purchased from your dealer or from the Spare Parts Department e Remove the shelf in front of the filter e Grip the filter and turn it 90 clockwise or anti clockwise to remove e Insert the new filter in the vertical position and Code Rev D 20140818 IEC 16 turn it 90 clockwise or anti clockwise until it clicks into position DOOR LOCK If the unit is provided with a lock system the keys are located inside the plastic bag that contains the Owner s Manual Insert the key into the lock push in and turn it counterclockwise to unlock the door To lock the door do the reverse operation making sure metal pin is engaged completely Remove the key and place it in a secure place for safekeeping CLEANING YOUR APPLIANCE Turn off the power unplug the appliance and remove all items including shelves and rack Wash the inside surfaces with a warm water and baking soda solution The solution should be about 2 tablespoons of baking soda to a pint of water
39. the appliance at exhibitions or in salesrooms In Eco Demo mode the compressor and all fan motors are switched OFF By pressing and holding the UP amp DOWN The controls of lower zone for dual zone amp three zone models and LIGHT keys at the same time for at least 5 seconds the indicator light will flash five times to confirm the input and the unit will operate in Eco Demo mode Eco Demo mode can be exited by repeating the above process OPERATING NOISES The unit is cooled by a compressor refrigeration aggregate The compressor pumps coolant through the cooling system producing operating noise Even when the compressor cuts out noises caused by changes in temperature and pressure are unavoidable Operating noise will be most audible immediately after the compressor cuts in It becomes quieter as the operating period continues The following noises are normal and occur from time to time Gurgling sound caused by the refrigerant flowing through the appliance s coils Humming noise made by the motor compressor This noise can get louder for brief periods when the motor is switching on Cracking popping sounds resulting from the materials contraction and expansion due to temperature variations Fan operating sound to circulate the air within the wine cabinet Unusual noise is normally the result of improper installation Under no circumstances must tubing come into contact with a wall other fu
40. velled Fig 5 11 Transfer the handles and plugs to the opposite positions Code Rev D 20140818 IEC 10 OPERATING YOUR APPLIANCE This appliance is designed for operation at certain ambient temperatures The climate class is specified on the rating plate The appliance may not work properly if it is left for a long period at a temperature outside the specified range For example placing your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate The range between 5 C and 22 C 41 F and 72 F may not be reached Climate class Ambient room temperatures SN 10 C to 32 C N 16 C to 32 C ST 16 C to 38 C T 16 C to 43 C NOTE Units with no heater will not raise its internal temperature if the ambient temperature where the unit is located is lower than the set temperature NOTE e When you use the appliance for the first time or restart the appliance after having been shut off for a long time there could be a few degrees variance between the temperature you select and the one indicated on the LED readout This is normal and it is due to the length of the activation time Once the unit is running for a few hours everything will be back to normal If the unit is unplugged power lost or turned off you must wait 3 to 5 minutes before restarting the unit If you attempt to restart before this time delay the unit will not start USE AND CONTROL SINGLE ZONE
Download Pdf Manuals
Related Search