BA med control D 10-10-18.indd, page 6 @ Preflight
Contents
1. Manual Clock Adjusting mode 31 Operations c Periodical receiving The machine will automatically receive the RCC signal at the time 2 05 and 14 05 every day You can skip the receiving process by press the button START to enter clock mode 3 Manual Clock Adjusting Normally the time and date can be adjusted by RCC signal automatically But you also can try manual clock adjusting if no RCC signal or weak signal a When the machine is in Clock Mode press the START and MEM button at the same time abt 2 sec the machine enters Forced RCC Receiving mode then press START button the machine en ters manual Clock Adjusting Mode b The number of year will twinkle first picture 4 Press START button continuously the numbers of month day hour and minute will twinkle in turn While the number is twinkling press MEM button to increase the corresponding number Keep on pressing the button MEM the number will incre ase fast c You can exit the Clock Adjusting Mode by pressing button START when the number of minute is twin kling then enter the Clock Mode d When you change the batteries the clock will be reset You can readjust clock or let the monitor mo difying the clock by RCC automatically 32 Operations Measuring blood pressure a After your body is in a comfortable position press he START button After a long beep BPM will verify itsel2. appliances and used bat teries in compliance with statutory regulations dispo sal in general household waste is prohibited 28 Preparation for Use Attaching the pressure cuff 1 Wrap the cuff around the left arm The arm should be bare 2 Fasten the cuff Don t pull it too strong or make the cuff too tight The edge of the cuff should be appro ximately 1 inch from the crease of your elbow 1inch 2 3cm 3 Attach the cuff on the right arm as shown in the fi gure if it is not possible to measure on the left arm 1inch 2 3cm 29 Preparation for Use Posture during measurement 1 Sit upright and ensure that the cuff is at heart level Relax and retain a natural posture during measure ment 2 Measure and record blood pressure at the same time every day to establish your blood pressure pattern AC Adapter It is possible to use a stabilized AC adapter output 6 V DC 800 mA to operate the device Note 1 No power is taken from the batteries while the AC adapter is connected to the device 2 If AC adapter power is interrupted during measure ment the device must be reset by disconnecting the AC adapter from the device 3 Please consult an appropriate dealer if you have questions relating to the adapter Power source 4 alkaline type AA batteries 1 5 V or stabilized AC DC adapter 6 V DC 800 mA 30 Operations Setting the clock and date 1 Clock Mode Once
3. is over shows 15 mmHg for lon Er 6 ger than 3 min At the start of measurement the pressure reading must be below 15 Measure mmHg again after 5 minutes If LCD EEPROM acces ihe monitor is shows sing error still abnormal Er7 please LCD twin Device parame oe kling all ter check error butor or the LCD MCU self verity factory shows error Er 9 LCD Span error shows Er LCD EEPROM backup shows error Er b BPM no Incorrect ope response ration Take out nat vnen its minutes and a BPM then reinstall hang all batteries 40 Specifications Display System Measuring Method Power Source Measuring Range Accuracy Memory Low Battery Indicator Auto Power Off Battery Life Operating Environment Storage Environment Dimensions Weight Liquid Crystal Display oscillometric method automatic air inflation and measurement 4 alkaline AA type batteries 1 5V or AC DC adapter optional blood pressure measuring range 0 295mmHg Heart pulse rate range 40 180 pulse beats min 3mmbHg blood pressure 5 pulse beats per minute 2 x 99 memories with time and date displaying yes after 1 minute Approx 200 measurements 5 C 40 C RH lt 80 20 C 55 C RH lt 95 160mm x 115mm x 69mm 364 g monitor 90 g batteries Specifications are subject to change without notice for purposes of product improvement It is recomm
4. to the mode without memory 36 Care and maintenance Do not drop the unit It is not shock proof W Do not modify or disassemble the unit or the arm cuff 4 Do not twist the arm cuff Use a cloth moistened with water or neutral detergent to clean the body of the unit and then wipe it dry a 37 Care and maintenance Avoid thinning agents benzine and other harsh cleaners Keep the unit ina suitable place Avoid high tempera tures direct sunlight high humidity level and dust M b ii Remove the batteries if the unit will not be used for a long time Do not press the POWER button if the cuff has not been properly wrapped around the arm 38 Error messages Abnorma Reason Checkout lity LCD Batteries low Change the shows low batteries battery symbol LCD Pressure system shows is unstable before Er 0 measurement LCD Systolic pressure Don t move of detect fail and try again LCD Diastolic pressu shows re detect fail Er 2 LCD Pneumatic shows system blocked Erg or cuff is too tight during inflation Place the cuff correctly and LCD Pneumatic sy try again shows stem leakage or Er 4 cuff is too loose during inflation 39 Error messages Abnorma Reason Checkout lity LCD Inflation above shows 300mmHg Er 5 LCD Pressure
5. you install the batteries with two beep the LCD will display the time and date by turns At the same time the machine enters the Radio Control led Clock Mode with the RCC symbol P twinkling After the RCC receiving the machine enters the Clock Mode and the LCD displays the time and date by turns And the COLOUR CHANGE LED will twinkle with the colour changed in random turn 2 Radio Controlled Clock RCC Receiving a Initial receiving Once you install the battery the machine enters the RCC Receiving Mode The RCC symbol twinkles during the receiving process If clock data received the time and date will be adjusted automatically And then enter the Clock Mode If no clock data re ceived the machine enters Clock Mode and keeps the time and date unchanged When the machine is in the RCC Mode you can skip RCC receiving and enter the Clock Mode by pressing START button b Forced RCC Receiving When the machine is in Clock Mode keep on pres sing both the button START and MEM at the same time for two seconds you will enter forced RCC mode and the RCC symbol is twinkling If clo ck data received the time and date will be adjusted automatically And then enter the Clock Mode with two beep If no clock data received the machine enters Clock Mode with long beep and keeps the time and date unchanged You can skip forced RCC Mode by pressing the but ton START Then the machine enters the
6. Digital Blood Pressure Monitor for the upper arm Geratherm med control INSTRUCTION MANUAL GT 5907 C Eons Contents Information you should know before operating the unit 0 0 0 ee eeeeeeeeeee 25 About the unit Function description Explanation of displays Preparation for use Installing Replacing batteries Attaching the pressure cuff Posture during measurement ee 30 Operations Setting the clock and date Measuring blood pressure WHO classification of blood pressure for adults Recalling memories a EraSing MOMONIOS jastissseeveascosasiecremissisests Care and maintenance 37 Error messages Specifications Quality standard Caution 1 Consult your physician to verify your blood pressure range before measuring it at home with this unit 2 If the cuff causes any discomfort during measure ment press the start stop button to turn off the unit immediately 3 If the pressure is over 300mmHg and the cuff does not deflate automatically pull off the velcro strap to detach the arm cuff Blood pressure measurements obtained with this unit are equivalent to those obtained by a trained person using the cuff stethoscope auscultation method WARRANTY Three years from the date of purchase 24 Information you should know before operating the unit What is blood pressure A force is created by the heart as the ventricleforcibly ejects blood into the blood ves
7. GE LED will also indicate the blood pressure classification a4 1am C008 43 sir ETI pict 3 g During the measurement you can turn off the moni or by press the START button h Pressing START button after measuring machine will be turn off or it will be automatically shut down after 1 minutes of none use Note If the symbol appears it means the unit has detected irregular pulse during measurement If the symbol appears regularly please consult a qualified physician for professional advice 34 Operations WHO classification of blood pressure for adults Diastolic mmHg Severe hypertension Grade 3 Moderate Hypertension Grade 2 Mild Hypertension Grade 1 Boarderline Optimal Blood pressu Systolic Diastolic Color BHww 3110 sfs re classifica BP mm BP mm indica tion HG Hg tor Optimal lt 120 lt 80 Green Normal 120 129 80 84 Green High Normal 130 139 85 89 Yellow Stage 1 Hypertension 140 159 90 99 Red Stage 2 Hyper tension 160 179 100 109 Red Stage 3 Hyper gt 180 gt 110 Red tension Please note that other risk factors e g diabetes obe sity smoking etc need to be taken into consideration and may affect these figures Consult with your physi cian for accurate assessment 35 Operations Recalling memories a Under the clock display
8. ended that the unit be calibrated by an authorised laboratory every two years 41 Quality standard The unit meets the requirements of Council Directive 93 42 EEC concerning medical devices A Quality Management system certified according to EN ISO 13485 guarantees that the product complies with the required quality criteria The blood pressure monitor conforms to EN 1060 1 Non invasive sphygmomanometers part 1 General requirements and EN 1060 3 Non invasive sphyg momanometers part 3 Supplementary requirements for electromechanical blood pressure measuring sy stems 42
9. f with LCD display all automatically and he COLOUR CHANGE LED will lighten with 3 co ours by turn picture 1 38 848 W os ts 7 0 dog te a co is Si Eat pict 1 b Then the LCD twinkle the current group sign and show the total of memories in this group Now you can modify the current group number by pressing he START button and confirm the current group by pressing the MEM button c Once you choose the group and if it already has memory LCD will show the latest result with the LED indicator picture 2 If machine does not have memory before the LCD will show six 0 at a mal men Raw J mor Be pict 2 d One second later LCD shows a single 0 While he down arrow does not twinkle until the air pres sure is stable and then it begins to measure auto matically 33 Operations e Then the monitor begins to pressurize automatically During the measurement the current pressure will display on the LCD and the bars will automatically rise up or fall down with the current pressure in the cuff The heart sign will glimmer with the heartbeat during the pressure are falling down f After measurement the result of systolic diastolic and pulse rate will all display on LCD And irregular heartbeat symbol and blood pressure classification indicator will twinkle picture 3 The result will be automatically memorized by itself And the CO LOUR CHAN
10. ing mode press button MEM will enter the mode of recalling memories LCD will show how many results it has in the current group Now you can modify the current group numb er by pressing the START button and confirm the current group by pressing the MEM button b When the group is selected the average of last three records will be displayed If machine does not have memory before the LCD will show four 0 c After that the latest result will be displayed which is 01 for memory number The time which you mea sured will also be displayed Continuously press the MEM button previously memories will show by turns d All memories have the WHO classification and the COLOUR CHANGE LED will also indicate the blood pressure classification e If it has no memory or all memories have been de leted then LCD will show 0 for systolic diastolic and show 00 for the numbers of memory heart rate f Press MEM button again after the last memory the machine will power off Under the memory displa ying mode it will be automatically power off after 1 minute of none use Or you can press START but ton to shut down the machine Erasing memories When it displays one memory no matter which me mory holding on pressing MEM button for three se conds all memories will be deleted with three beep LCD will show the before you release the button then it comes
11. sels and through the vascular system Another force is created by the arte ries as they resist the blood flow Blood pressure is the result of these two forces What are systolic and diastolic pressures Systolic pressure is the highest pressure at the height of the heart s contraction Diastolic pressure is the lo west pressure when the heart is resting Is my blood pressure normal See the blood pressure classification chart released by the WHO World Health Organization on page 35 for evaluation of your blood pressure level What about low blood pressure In general a lower blood pressure reading is better un less it causes unpleasant symptoms such as fainting and or lightheadedness Fluctuation and variation in blood pressure The following chart shows possible blood pressure fluctuations during a 24 hour period 25 Information you should know before operating the unit mmHg 160 140 120 Systolic 100 80 Prema thin Lr Diastolic a a 12 6 0 6 11 PM AM The following factors will influence blood pressure measurement results and cause variations Bathing Mental tension e Breathing Eating Conversation Temperature change Drinking alcohol Thoughts Exercise Smoking etc e Moving About the Unit Function description Based on oscillometric method and silicon integrate pressure sensor technology blood pressure and heart rate can be measured automatically and non inva
12. sive ly which helps to ease the operation The Geratherm med control have 2 x 99 memories with date and time display a big LCD screen and arrhythmia detection The RCC radio controlled clock function can automa tically receive the German radio clock signal DCF77 to adjust the clock accurately And the colour LED for indicates the class according to WHO of your blood pressure Also the monitor has the function of aver aging the latest three records 26 About the unit cuff LCD Display Memory On Off Button The cuff is designed to fit arm sizes between 22 and 30cm 8 7 to 11 81 inches Explanation of displays Time RCC Low Batterie 38 8 VY MONTH DATE hoa De o WHO Ceiba classi fication l a Om D Diasto E E a E r AEE m Od I D En no Aa Pulse Group Irregular Heart Beat Memory IHB 27 Preparation for use Installing Replacing batteries 1 Insert the batteries into the battery compartment matching correct polarities and 2 Replace all batteries if the low battery indicator ap pears 3 Remove the batteries if the unit will not be used for a long period of time 4 REMOVE all of the BATTERIES when utilizing the optional AC adapter Note It is recommended that the same type of alkaline bat teries be used to avoid incompatibility Rechargeable batteries with a voltage of 1 2V are not suitable for this product Please dispose of defective
Download Pdf Manuals
Related Search