Home

Instructions

1. Users Manual English version VGA WATER BLOCK for Nvidia Geforce 8800 GTS GTX ZM GWB8800 GTS GTX Please visit our website and watch the ZM GWB8800 GTS GTX installation video for easy installation x Please read this manual thoroughly before installation http www zalman co kr http www zalmanusa com Precautions 1 Test the product for leakage away from the system before installing it on the system Once no leakage is confirmed proceed with the installation and use 2 Used approved coolant for computer water cooling to prevent corrosion 3 Use coolant tubes listed under the compatibility list 4 Do not install the product if it interferes with any VGA components 5 Design of this product does not allow product disassembly Do not disassemble the product Disclaimer Zalman Tech Co Ltd is not responsible for any damages due to external causes including but not limited to improper use problems with electrical power accident neglect alteration repair improper installation or improper testing 1 Features 1 Zalman s innovative dimple type processing technology allows lightness in weight and excellent cooling performance 2 Pure aluminum base material water block provides excellent heat transfer and anodized base prevents corrosion 3 High performance thermal pads with excellent elasticity provide great adhesion to all heat generating components 4 The optimized design allows e
2. VGA Card Thermal Grease 4 VGA Water Block Installation Insert the O ring into the Nipple Insert the Nipples installed on the VGA Water Block into the Mounting Holes after aligning them Install the PVC Washers Springs and Nuts on the back side of the VGA card in the mentioned order Nipple Il O Ring PVC Washer Spring Nut Note 1 Check to see if the Water Block s base side is in proper contact with the VGA chipset before finishing the installation Note 2 Assembling the Springs with the Nuts prior to installation will ease the installation process Spring PVC Washer x The specifications of any product may change without prior notice to improve performance 5 5 Tension Control of the VGA Water Block Tighten loosen the Nuts on the back side of the VGA card to control the tension between the VGA Water Block and the VGA Chipset Note 1 If the Nuts are turned to tightly then the VGA chipset or VGA card could get damaged Note 2 Fully tightening one Nut at a time may result in damaging the VGA Chipset Please tighten each Nut one rotation at a time until all are completely tightened Note 3 Make sure that the VGA Water Block does not interfere with the VGA cooler capacitors and other components of the VGA card 6 VGA Card Installation Insert the VGA card as
3. asy installation and direct cooling of RAM FET and I O chipset 2 Specifications 1 Weight 420g 2 Materials Water Block Cover Base Pure Aluminum Fitting Brass 3 Dimensions 93 W x 183 L x 31 H mm 4 Compatible Tubes Outer x Inner 13 x 9mm 12 x 8mm 11 x 8mm 10 x 8mm x The specifications of any product may change without prior notice to improve performance ER 3 Components 1 Common Components VGA Water Block Assembly Nine 9 Nipples Nine 9 Nuts Two 2 PVC Washer Plates Ten 10 Springs Ten 10 O rings Two 2 Tube Clamps Two Thermal Grease Thermal Pads One 1 14X14X1T for I O Chipset Contact Four 4 7X23X1T for FET Contact Three 3 16X70X1T for RAM Contact User s Manual 8 exe 8 HE OO tonton tw LL E x The specifications of any product may change without prior notice to improve performance 2 4 Exploded View ZM GWB8800 GTS Water Block Assembly i gt CO bd Ee 1 i G amp PVC Washer ea ti Se Spring D e Fa Nut g in ey ZM GWB8800 GTX Water Block Assembly 5 Installation x This instal
4. lation method applies to both GTS GTX Install Tap 1 Nipple Installation Install the Nipple onto the Install Tap on the base side of the Water Block Note 1 Use a tool such as Long Nose Pliers to firmly tighten the Nipples 2 Thermal Pad Attachment Thermal Pad x for FET Contact Oa Thermal Pad for I O Chipset Contact Thermal Pad for RAM Contact Water Block Base Clean the contact surface of the VGA Chipset completely As shown in the diagram attach the Thermal Pads on the bottom side of the Water Block base marked with dotted lines that will come in contact with the RAM FET and I O Chipset Note 1 If the Thermal Pads are crookedly attached or attached on the wrong place then carefully remove them and attach properly Note 2 Pay attention so that the Thermal Pads do not get bent or damaged when attaching them Note 3 Exerting too much pressure when adhering the Thermal Pads could cause compression which could lead to a gap between the Thermal Pads and the Water Block during VGA card installation Must carefully attach them Note 4 Using tweezers or a knife can facilitate the detachment of the protective film from the Thermal Pads x The specifications of any product may change without prior notice to improve performance a 3 Thermal Grease Application Evenly apply the Thermal Grease on the GPU surface that comes in contact with the VGA Water Block
5. nd tidy cable installation Blue LEDs for cool aethetics Gaming PC Enc High end Gaming Enclosure built sturdy all aluminum aanels Three tool free hinged magnetic panel 2 Left 1 Right for easy installation and access to components Tool free installation of disk drives Fan Controllers Audio interfaces etc Accommodates up to 6 Hard Drives Luxurious and cool aesthetics Color option Black Red LED Fans Titanium Blue LED Panel GT 1000 For more information please visit our website Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems x The specifications of any product may change without prior notice to improve performance 8
6. sembled with the VGA Water Block into the motherboard s PCle or AGP slot Use the Fixing Bolt to secure the VGA card onto the computer case Fixing Bolt x The specifications of any product may change without prior notice to improve performance 6 7 Installation of Tubes and Tube Clamps Plug the tubes over the VGA Water Block s fittings and install the Tube Clamps Note 1 Hold the VGA card with one hand when plugging the Tube into the Fitting Note 2 Use of a tool such as Long Nose Pliers when installing the Tube Clamp will ease the installation process Note 3 Pull on the tube after installing the Tube Clamp to check the tension a Tube a __ Tube Clamp Zalman Noise Preventior Stable performance and noiseless liquid cooling system can both be achieved with the use of Zalman s CPU Water Block Hard Disk Cooler Noiseless Case Fan and Northbridge Water Block CPU Water Block Heatpipe H D D Cooler Noiseless Case Fan Northbridge Water Block Heatpipe Cooled Modular ZM500 HP ZM600 HP Reduction in the PFC circuitry s switching FET heat generation by use of 3 Parallel switching FETs normally 1 or 2 used Heatpipe cooling system on the main rectifier output diodes for maximum stability and minimum fan speed for ultra quiet operation Modular design for convenient a

Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents