XL-2T User`s Manual - Satellite Industries, Inc.
Contents
1. Not Ready Example If the READY light is not lit and the Zone 1 light is solid ON an alarm sensor on Zone 1 is faulted This might mean that a door is open or someone is walking in view of a motion sensor Check all sensors on Zone 1 and resolve the problem When all sensors are restored the READY light will come ON and the zone light will go out In this example the display shows SYSTEM NOT READY and NOT RDY ZONE 1 FRONT DOOR Determine which zone or zones are not ready resolve the problem and turn the system ON normally If the problem cannot be resolved you may bypass the zone that is not ready Bypassing should only be done if the problem on the zone cannot be resolved OR if you intentionally wish to leave the zone OFF For example you would leave the zone OFF if you plan to keep the window open for ventilation Zones that are bypassed are not protected when the system is ON See Bypass on the following page for a description of the procedure Turning The System ON cont TO TURN SYSTEM ON AND LEAVE Enter your 4 digituser code l The System ON ARM light will go ON or the display will show ON AWAY Exit through a door designated by your installer as an exit entry door You must leave within the exit time programmed by your installer Refer to the reference sheet for the time that has been set for your system TO TURN SYSTEM ON AND STAY INSIDE To tur2. OBLIGATIONS OR LIABILITIES MADE BY SELLER IN CONNECTION WITH THIS PRODUCT INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE ARE LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE ANY ACTION FOR BREACH OF ANY WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN 60 MONTHS FROM DATE OF ORIGINAL PURCHASE IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER S OWN NEGLIGENCE OR FAULT Some states do not allow limitation on how long an implied warranty lasts or the exdusion or limitation of incidental or consequential damages so the above limitation or exdusion may not apply to you Seller does not represent that the product may not be compromised or circumvented that the product will prevent any personal injury or property loss by burglary robbery fire or otherwise or that the product will in all cases provide adequate warning or protection Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary robbery fire or other events occurring without providing an alarm but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss
3. Check to make sure the system is ready to be armed no faulted zones When it is ready press INSTANT followed by your user code J When the system has been turned ON successfully the ON OFF light and the Instant light will be ON or the LCD will display ON INSTANT TO BYPASS A ZONE The Bypass function exdudes a zone of protection from the security system until it is unbypassed either by using the unbypass procedure or when you turn the system OFF Bypassing can only be done while the system is turned OFF Press the BYPASS button Then enter your user code and the zone number 1 7 to be bypassed as follows BYPASS followed by your user code ER ESSE ma ZONE 1 f the Quick Bypass feature has been enabled by the installer the user code is not required when bypassing zones NOTE Bypassed zones are NOT protected when the system is turned ON After the bypass command has been accepted the keypad will sound one long beep and the zone LED of the zone s bypassed will slowly blink or the LCD will display BYPASS ZONEO IMPORTANT Temporary users i e baby sitters FRONT DOOR housekeepers etc should not be shown the Bypass procedure TO UNBYPASS A ZONE Pressing the BYPASS button returns a bypassed zone to normal operation To unbypass a zone s repeat the bypass function as follows BYPASS followed by your user code ZONE After unbypassing the zone display will show th
4. doors 17 Glossary cont EXIT DELAY The period of time allowed between turning the system on and leaving through a designated exit entry door before the system will register an alarm condition This is determined at the time of installation INTERIOR ZONE An interior zone is a group of points that protect the interior of your premises You may want to turn the perimeter portion of your system on while leaving the interior zones OFF to allow you to open interior doors and pass interior motion detectors without causing an alarm KEYPAD A keypad is your link into your system It displays alarm and trouble messages shows faulted zones and allows you to turn the system ON or OFF by using the buttons Your system will have one or more keypads ON OFF These terms refer to the burglary portion of your security system There are several levels of operation that allow you to protect part of your premises while you remain inside Fire sensors and other emergency and environmental features are always active and ready they are not affected in any way by turning the burglary portion of your security system ON or OFF Other terms used are armed system is on and disarmed system is OFF See ON INSTANT ON STAY and STAY ON OFF INDICATOR Red light in the upper portion of the keypad labeled Armed When lit some part of the burglar alarm system is ON when nct lit the burglary portion of the system is OFF ON STAY A syst
5. insurance rates but an alarm system is not a substitute for insurance Homeowners property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property We continue to develop new and improved protection devices Users of alarm systems owe it to themselves and their loved ones to learn about these developments 22 LIMITED WARRANTY Fire Burglary Instruments Inc a subsidiary of Pittway Corporation and its divisions subsidiaries and affiliates Seller 149 Eileen Way Syosset New York 11791 warrants its security equipment the product to be free from defects in material and workmanship for one year from date of original purchase under normal use and service Seller s obligation is limited to repairing or replacing at its option free of charge for parts labor or transportation any product proved to be defective in materials or workmanship under normal use and service Seller shall have no obligation under this warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than the Seller In case of defect contact the security professional who installed and maintains your security equipment or the Seller for produc repair This one year Limited Warranty is in lieu of all other expressed warranties obligations or liabilities THERE ARE NO EXPRESS WARRANTIES WHICH EXTEND BEYOND THE FACE HEREOF ANY IMPLIED WARRANTIES
6. 7 NOTE Bypassed zones are not protected when the system is turned ON After the bypass command has been accepted the keypad sounds one long beep The zone light of the bypassed zone s will slowly blink or the display will show BYPASSED ZONE 1 FRONT DOOR NOTE Temporary users i e baby sitters housekeepers etc should not be shown the Bypass procedure 12 Miscellaneous Commands cont TURN CHIME ON OFF Chime is an optional feature that causes the keypad to chime when selected doors are opened while the burglary protection is OFF or disarmed Only your installer can program a zone for the Chime feature Once programmed you can turn Chime ON or OFF to meet your daily needs Toturn Chime ON or OFF Press 6 SET AUTO ARM ON TIME Setting Auto Arm ON time lets you set the time of day your system will automatically turn ON To activate Set Auto Arm ON time Press 5 hour minute The two digit settings for hours and minutes are in the 24 hour format Example 7AM 07 3PM 15 Set minutes the same way 5min 05 25min 25 Thereadout keypad will prompt you for the required entries DOOR STRIKE Door strikes are used in access control applications To activate door strikes Press 9 User Code Door where the door number is as follows 1 2 NOTE User 13 is the only user code that can perform the door strike function VIEW TIME To view thetime press 7 CURRENT TIME 08 15AM SET TI
7. FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment on the user is encouraged to try and correct the interference by one or more of the following measures If using an indoor antenna have a quality outdoor antenna installed Re orient the receiving antenna until interference is reduced or eliminated Move the receiver away from any wire runs to the control communi cator Plug the control communicator into a different outlet so that it and the receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user or installer may find the following booklet prepared by the Federal Communications Commission helpful Interference Handbook This booklet is available from the U S Government Printing OFFice Washington DC 20402 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User Guide Unauthorized changes or modifications could void the user s authority to operate the equi pment TELEPHONE OPERATIONAL PROBLEMS In the event of telephone operational problems disconnect the control by remov
8. ME Toset the time and date press 3 user 1 or 2 code hr hr min min mnth mnth day day year year The user code is not required if so programmed by installer TO VIEW AUTO ARM ON TIME To view the auto arm time press 7 8 user 1 or 2 code AUTOARM TIME 05 00PM The user code is not required if so programmed by installer 13 Testing The System SYSTEM TEST It is recommended that you test your system once a week using the following procedure NOTE If your system is monitored contact your Central Station before you perform this test 1 Turn your security system ON 2 Wait until your exit time is over Then activate the system by opening a protected zone for example a window or door 3 Confirm that the alarm sounding device bell or siren sounds If your system is connected to a Central Station the keypad will sound the ringback tone to confirm that the signal was received 4 Turn the security system OFF 5 Call the Central Station totell them you are finished testing BATTERY TEST It is recommended that you test your battery once a month In order to test your backup standby battery the following procedure should be followed 1 Unplug the transformer from the AC outlet by removing the restraining screw that secures the transformer to the wall NOTE The screw is not present on the models sold in Canada Observe that the AC indicator light on th
9. XL 2T Security System User Guide FIRE BURGLARY INSTRUMENTS INC Table Of Contents QUICK REFERENCE u eoo eee naha ions a aan nu iets 3 INTRODUCTION end e ete eet e sed 4 SYSTEM REFERENCE inscite ee deed dee dd ete i bete 5 TURNING THE SYSTEM QN b eee d eds 7 TURNING THE SYSTEM OFF esee nennen nennen tenentes 10 USER CODES eee e PU PUR ERU RR eH EHE RUE ERR HIR SERE Ra 11 MISCELLANEOUS COMMANDS eerte nennen nennen nennen 12 TESTING THE SYSTEM ovis o nat perite t peine Lote tus tose I Ee eerie 14 NATIONAL FIRE PROTECTION ASSOCIATION RECOMMENDATIONS ON SMOKE DETECTORS egit remet desti EC D DHL eR CERE CELERE 15 EMERGENCY EVACUATION e eeeseeeeeeteete te netntn eene teen tne tentent seen eee tnnt eene 16 GLOSSARY actacnedtereedtec R Ente Dea Ded De HE Leb De dE Dee Lee ERRE n 17 FEDERAL COMMUNICATIONS COMMISSION FCC STATEMENT 20 TELEPHONE OPERATIONAL PROBLEMS eerte 20 LIMITATIONS OF THIS ALARM SYSTEM 1 eterne 21 LIMITED WARRANTY oo eo eed Sodas ed u then etre eerte tes 23 Quick Reference TO TURN SYSTEM ON 1 Check to make sure the system is ready Green READY light is lit 2 Enter your 4 digit user code Sa ee 3 Exit through a door designated by your installer as an exit entry door 4 TheON OFF ARM light will light TO TURN SYSTEM OFF 1 Enter through a door designat
10. an alarm sensor or disconnect an alarm warning device Intrusion detectors eg passive infrared detectors smoke detectors and many other sensing devices will not work without batteries or if the batteries are not put in properly Devices powered solely by AC will not work if their AC power supply is cut off for any reason however briefly Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver Even if the signal path has been recently checked during a weekly test blockage can occur if a metal object is moved into the path A user may not be ableto reach a panic or emergency button quickly enough While smoke detectors have played a key role in reducing residential fire deaths in the United States they may not activate or provide early warning for a variety of reasons in as many as 35 of all fires according to data published by the Federal Emergency Management Agency Some of the reasons smoke detectors used in conjunction with the System may not work are as follows Smoke detectors may not sense fires that start where smoke cannot reach the detectors such as in chimneys in walls or roofs or on the other side of dosed doors Smoke detectors also may not sense a fire on another level of a residence or building A second floor detector for example may not sense a first floor or basement fire Moreover smoke detectors have sensing limitations No smoke detector can sense every kind of fi
11. and programmed for special levels of access and notification BYPASS FEATURE The Bypass feature allows you to exclude a selected zone or zones from the burglar alarm protection BYPASS BUTTON A button on the keypad used to activate the Bypass feature CENTRAL STATION The signal monitoring center contacted by your security system over the telephone and or other communication channels when alarms are activated if your system is programmed to communicate alarms off site The Central Station will follow their procedures and your instructions for contacting the proper authorities when a signal is received CHIME FEATURE An optional feature that causes the keypad to chime for one second when selected doors are opened when the burglary protection is OFF or disarmed Once programmed by your installer you can turn Chime ON and OFF with 6 DISARMED See ON OFF system feature that you may have programmed into your system If someone forces you to turn your system OFF entering the special Ambush Duress user code turns the system OFF and sends a silent emergency signal to the Central Station so personnel there can respond appropriately ENTRY DELAY The period of time allowed between opening a designated Entry Exit door and turning OFF the alarm system before the system will register an alarm condition This is determined at the time of installation Your system supports two entry times allowing you to have a different length of time for different
12. as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHILE SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER This warranty gives you specific legal rights and you may also have other rights which vary from state to state Noincrease of alteration written or verbal to this warranty is authorized 23 FBIKG FIRE BURGLARY INSTRUMENTS INC Subsidiary of PITTWAY CORPORATION 149 Eileen Way Syosset New York 11791 Copyright 2000 PITTWAY CORPORATION N9819V3 6 00
13. e keypad goes OFF Activate your alarm by performing the above SYSTEM TEST Remember to contact your Central Station if your system is monitored Plug the transformer into the AC outlet and secure with the restraining screw NOTE The screw is not present on the models sold in Canada The National Fire Protection Association publishes a standard for fire warning equipment NFPA publication 72 Further information can be obtained by contacting NFPA Public Affairs Dept Batterymarch Park Quincy MA 02269 If you have any further questions about the operation of your system please contact your alarm company National Fire Protection Association Recommendations On Smoke Detectors With regard to the number and placement of smoke heat detectors we subscribe to the recommendations contained in the National Fire Protection Association s NFPA Standard 72 noted below Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows A smoke detector installed outside of each separate sleeping area in the immediate vicinity of the bedrooms and on each additional story of the family living unit induding basements and exduding crawl spaces and unfinished attics In addition the NFPA recommends that you install heat or smoke detectors in the living room dining room bedroom s kitchen hallway s attic furnace room utility and storage rooms baseme
14. e state of the zones 9 Turning The System OFF When you turn the system OFF you turn OFF only the burglar portion of your system any smoke or heat detectors and panic keys will remain ON You must enter through a designated entry door and turn OFF the system within the time allowed Y ou can have different amounts of time for different entry points See your system reference sheet for the times established for your system Toturn your system OFF Enter your 4 digit user code L If noalarms havetaken place the ON OFF light labeled ARM will go OFF or the display will show SYSTEM READY If alarms occurred when the system was ON or if a trouble condition exists the zone LED s will indicate it as follows Fast Blink Alarm Slow Blink Low Intensity Bypass Slow Pulse Trouble Solid ON tusuna eras Not Ready or the LCD will display ALARM ZONE 1 FRONT DOOR Burglary alarms will sound a steady tone at the keypad s and fire alarms will generate a pulsing sound IMPORTANT If an intrusion has taken place while you were away do not enter until the location has been checked Call for help from a neighbor s house and wait there for the police After you have turned the system OFF with your user code the LCD keypads will display this message ALM MEM ZONE 1 FRONT DOOR Todear the display of alarm or trouble conditi
15. ed by your installer as an exit entry door 2 Enter your 4 digit user code L JL 3 The system ON ARM light will go out TO TURN SYSTEM ON AND STAY INSIDE 1 Check to make sure the system is ready Green READY light is lit 2 Press STAY 3 Enter your user code ICICI The ON OFF ARM light and the STAY light will both light REMEMBER Y ou must turn the system OFF if you want to open the door or leave the premises after the exit time has passed TO TURN THE SYSTEM ON INSTANT MODE AND STAY INSIDE 1 Check to make sure the system is ready Green READY light is lit 2 Press INSTANT 3 Press STAY E 4 Enter your user code ICIL OON The ON OFF ARM light the INSTANT light and the STAY light will all be on TO RESET SMOKE DETECTOR 1 Enter your 4 digit user code JJ JD J READY light is not available on all keypads Introduction Congratulations on your decision to protect your home or business with the XL 2T security system Y ou have chosen a reliable state of the art security system that is remarkably easy to operate Y our system has been professionally installed by your local Security Company whose representative can explain the specifics of your system The keypad is the input and display device for your security system Your Security Company representative will suggest the model most appropriate for your premises and your needs The XL 2T i
16. em setting that turns ON the perimeter protection of the building but allows movement throughout the interior PANIC BUTTON A push button that allows you to signal the Central Station that you need immediate assistance Your system has programmable Keypad Send Help Alerts that can also serve as Panic buttons PERIMETER ZONE A perimeter zone is a group of points that protect the exterior of your premises Y our outside doors and windows would be programmed as a perimeter zone 18 Glossary cont SENSOR The actual alarm sensor detector or device installed to detect an intrusion fire or environmental problem Examples include door contacts window contacts motion sensors glassbreak sensors smoke detectors rate of rise heat detectors temperature sensors flood water sensors and carbon monoxide gas detectors SILENT CONDITION Most types of alarms and troubles alert you with the keypad sounder and the sirens horns or speakers located in your premises The intent is to advise you of the alarm or trouble and allow you to respond promptly The audible sounds also let an intruder know that he has been detected and will hopefully scare him away In some circumstances an audible alarm might put your life in danger For that reason those alarms are programmed as silent conditions For an example see AMBUSH DURESS SYSTEM Your security system is composed of three main parts 1 the control panel which functions as the sy
17. ing the plug from the RJ 31X wall jack We recommend that your certified installer demonstrate disconnecting the phones on installation of the system Do not disconnect the phone connection inside the control communicator Doing so will result in the loss of your phone lines If the regular phone works correctly after the control communicator has been disconnected from the phone lines the control communicator has a problem and should be returned for repair If upon disconnection of the control communicator there is still a problem on the line notify the telephone company that it has a problem and request prompt repair service The user may not under any circumstances in or out of warranty attempt any service or repairs to the system It must be returned to the factory or an authorized service agency for all repairs This control unit was manufactured under rigid quality standards and complies with all UL requirements for its intended use Maintenance is best performed by your installing company with trained service personnel 20 LIMITATIONS OF THIS ALARM SYSTEM While this system is an advanced design security system it does not offer guaranteed protection against burglary fire or other emergency Any alarm system whether commercial or residential is subject to compromise or failure to warn for a variety of reasons For example Intruders may gain access through unprotected openings or have the technical sophistication to bypass
18. is feature If programmed user code 5 will have System ON capability only and you can issue this code to a temporary user so he can securethe premises when he leaves 11 Miscellaneous Commands SEND HELP ALERTS Your system can be programmed for 3 separate keypad Send Help alerts that would send an emergency signal to your Central Station See the System Reference sheet to see which have been programmed for your system AMBUSH DURESS Your system can be programmed to send an emergency signal to the Central Station if you are forced to enter the premises or are under duress of any kind If you choose to indude this feature User Code 15 is dedicated to this function and must only be used under these circumstances QUICK ON QUICK ARMING If programmed by your installer Quick ON or Quick Arming allows you to turn the system ON tothe AWAY mode without entering a user code NOTE Turning your system OFF always requires a valid user code Press 1 QUICK FORCED ON If programmed by your installer Quick Forced ON allows you to turn the burglar portion of your alarm system ON to the AWAY mode bypassing all zones that are not ready Press 75 2 NOTE A valid user codeis still required to turn the system OFF NOTE This feature is disabled on UL installations QUICK BYPASS If you have Quick Bypass programmed for your system you will not have to use your user code to bypass zones The Quick Bypass procedure is ZONE 1
19. lowing table enter the names of the individuals assigned to each specific User ID number USER ID ASSIGNED TO 1 MASTER USER 2 MASTER USER 12 13 Door Strike Yes No If No If user 13 is not assigned to door strike then any user can activate the door strike 14 Only Turns System ON Yes If No 15 Ambush Duress Code Yes If No Master Users can add change or erase other user codes f your installer enables only User 4 to report openings and dosings to the CS then only those person s that you assign User 41D to will cause a report to be generated MONITORING STATION INFORMATION Account Telephone Turning The System On IS THE SYSTEM READY You can turn the burglar portion of your security system ON and OFF Before you can turn the system ON it must be ready If you have a protected door open or someone is moving in view of a motion detector the system will not display READY The system is ready if the READY light is ON or if the display shows SYSTEM READY WHEN SYSTEM IS NOT READY If the system is not ready to be armed the READY light will be OFF and the zone lights will show which zone or zones are not ready The following conditions will be indicated by the zone lights or described on the display Fast Blink Alarm Slow Blink Low Intensity Bypass Slow Pulse Trouble Solid ON
20. n the perimeter portion of your burglar alarm ON and move around freely insidethe premises use the STAY mode Check to make sure the system is ready When it is ready press STAY followed by your user code When the system has been turned on successfully the ON OFF ARM light and the STAY light will belit or the LCD will display ON STAY REMEMBER You must turn the system OFF if you want to open the door or leave the premises after the exit time has passed TO TURN SYSTEM ON IN INSTANT MODE AND STAY INSIDE In INSTANT STAY mode the perimeter portion of your burglar alarm system is ON and the time delays are eliminated from your normal Entry E xit door s All interior protection is OFF so you are free to move around inside Check to make sure the system is READY When it is ready press INSTANT followed by STAY followed by your user code L When the system has been turned ON successfully the ON OFF ARM light the INSTANT light and the STAY light will all be ON or the LCD will display ON STAY INSTANT Turning The System ON cont NOTE This system can be programmed by the installer for the AUTO STAY feature which automatically bypasses interior zones if you arm the system and do not exit through a delay zone during exit time TO TURN SYSTEM ON IN INSTANT MODE In INSTANT mode all alarm sensors induding those on doors and windows will report an alarm immediately if activated
21. nts and attached garages KITCHEN A O a Ne DINING TV ROOM LIVING ROOM A O O O LIVING ROOM BEDROOM BEDROOM lll Smoke Detectors for Minimum Protection O Smoke Detectors for Additional Protection A Heat Activated Detectors L BEDROOM O mo BEDROOM BEDROOM GARAGE 15 Emergency Evacuation Establish and regularly practice a plan of escape in the event of fire The following steps are recommended by the National Fire Protection Assocation l Position your detector or your interior and or exterior sounders so that they can be heard by all occupants 2 Determine two means of escape from each room One path of escape should lead to the door that permits aee Scb normal exit from the building The other is an S RASA alternative route such as through a window should your es 2 Pi normal escape path be unpassable Station an escape ze FEOOR ladder at such windows if there is a long drop to the amp i ground ee 3 Sketch a floor plan of the building Show windows P a doors stairs and rooftops that can be used to escape cbe m Indicate escape routes for each room Keep these routes P FLOOR free from obstruction and post copies of the escape routes in every room inr 4 Assure that all bedroom doors are shut while you are aslee
22. ons and silence the audible alert Enter your 4 digit user code is C C again 10 User Codes TO ADD OR CHANGE A USER CODE Users can be added or changed directly at the keypad Your system can have up to 15 different user codes Users 1 and 2 are the only users allowed to add or delete other user codes To add or change a user code press the CODE button followed by user 1 or user 32 of the 4 digit user code Then enter the new user number and the new 4 digit user code The keypad will beep after each digit is pressed User 1 or 2 Code User ID New User Code OOOO m Ex sa a Use the system reference sheet to record system users On this sheet your installer will indicate if you have chosen to dedicate a user code to send an emergency Ambush or Duress signal You may also have chosen to reserve one user code that is only allowed to turn the system ON This code will NOT be able to turn the system OFF TO DELETE A USER CODE To delete a user press the Code button followed by the 4 digit master user code Enter the the user number then press to delete For example to delete user 3 dothe following Master User Code User ID to delete LEIDEN i NOTE User 1 the master user cannot be deleted but it can be changed using the ADD OR CHANGE user procedure THE ARM ONLY CODE Maid Code If you choose to have a code that cannot turn the system OFF but can turn the system ON have your installer program th
23. p This will prevent deadly smoke from entering while you escape 5 Try the door If the door is hot check your alternate escape route If the door is cool open it cautiously Be prepared to slam the door shut if smoke or heat rushes Ll gl in 6 When smoke is present crawl on the ground Do not walk upright since smoke rises and may overcome you Clearer air is near the floor 7 Escape quickly don t panic 8 Establish a common meeting place outdoors away from your house where everyone can meet and then take steps to contact the authorities and account for those missing Choose someone to assure that nobody returns to the house many die going back FRONT 16 Glossary AC INDICATOR Small green power ON OFF light between the center buttons on the keypad When lit the system is running on primary power when not lit the system is running off the backup battery ALARM Sound from keypad or other horn siren indicates a burglar alarm fire alarm or other condition you should be alerted to ARMED See ON OFF AWAY A system setting that protects the premises while it is unoccupied All burglary sensors are active BURGLARY FIRE The two major functions of a security system Fire protection is always ON and cannot be turned OFF The burglary sensors protect against unauthorized entry into your premises The burglary protection can be turned ON and OFF
24. re every time In general detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed violent explosions escaping gas improper storage of flammable materials overloaded electrical dircuits children playing with matches or arson Depending on the nature of the fire and or the location of the smoke detectors the detector even if it operates as anticipated may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death Passive I nfrared Motion Detectors can only detect Intrusion within the designed ranges as diagrammed in their Installation and Setup Guide Passive I nfrared Detectors do not provide volumetric area protection They do create multiple beams of protection and Intrusion can only be detected in unobstructed areas covered by the beams They cannot detect motion or intrusion that takes place behind walls ceilings floors dosed doors glass partitions glass doors or windows Mechanical tampering masking painting or spraying of any material on the mirrors windows or any part of the optical system can reduce their detection ability Passive Infrared Detectors sense changes in temperature however as the ambient temperature of the protected area approaches the temperature range of 90 degrees to 150 degrees F ahrenheit the detection performance can decrease 21 LIMITATIONS OF THIS ALARM SYSTEM cont Alarm warning devices such as siren
25. s bells or horns may not alert people or wake up sleepers who are located on the other side of dosed or partly open doors If warning devices sound on a different level of the residence from the bedrooms then they are less likely to waken or alert people inside the bedrooms Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo radio air conditioner other appliances or by passing traffic Finally alarm warning devices however loud may not warn hearing impaired people or waken deep sleepers Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service Telephone lines are also subject to compromise by sophisticated intruders However even if the system responds to the emergency as intended occupants may have insufficient time to protect themselves from the emergency situation In the case of a monitored alarm system authorities may not respond appropriately This equipment like other electrical devices is subject to component failure Even though this equipment is designed to last as long as 10 years the electronic components could fail at any time The most common cause of an alarm system not functioning when an intrusion or fire ocaurs is inadequate maintenance This alarm system should be tested weekly to make sure all sensors are working properly Installing an alarm system may make one eligible for lower
26. s listed by Underwriters Laboratories for Household Fire and Burglary applications Throughout this manual the following conventions are used to represent the keystrokes required to perform the following functions STAY Press button labeled STAY BYPASS Press button labeled BYPASS INSTANT Press button labeled INSTANT CODE Press button labeled CODE LILILIL Enter 4 digit user code Please keep your manual in a convenient location so you can refer to it if needed System Reference ZONE DESCRIPTIONS In the following table enter a description of the area of protection for each zone Example Zone 1 Windows on North side of building Zone 4 Main entrance to building ZONE DESCRIPTION 1 2 3 4 5 6 7 Entry time Door Exit time Entry time Door Exit time is the same for all designated Entry E xit doors SEND HELP ALERT All keypads are equipped with emergency pair keys In order to activate the alert both keys must be pressed at the same time The type of keypad you have installed dictates which keys you press Your installer will show you how to activate these emergency keys The emergency keys used for all keypads are shown below The following SEND HELP ALERT is programmed into my system KEYS DESCRIPTION 4 amp x Right 7 amp 9 Left 1 amp 3 Center Buttons on XL 4600SM keypad only z5 System Reference cont USER CODE ASSIGNMENTS In the fol
27. stem brain and the link to the monitoring agency Central Station 2 the keypad s which provide you with system status and allow you to input commands 3 security sensors such as door and window contacts motion sensors smoke detectors and other sensors as required to detect intrusion fire and other conditions for your premises USER CODE A user code is a 4 digit code that is required to operate the system The system supports up to 6 separate user codes The system supports one master user who can add delete other user codes Two of the user codes may be dedicated to special functions as defined by your alarm company at the time of installation See the User Code List in the back of this manual ZONE A zone is a collection of sensors with common characteristics grouped together for your operating convenience The system will support 6 zones or groupings 19 FEDERAL COMMUNICATIONS COMMISSION FCC STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use TheFCC requires the following statement for your information This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a dass B computing device in accordance with the spedfications in Subpart J Part 15 of
Download Pdf Manuals
Related Search