User`s Manual
Contents
1. Do not allow anything to rest on the power cord Do not locate this television equipment where the cord may be damaged due to lightning and power line surges Follow all warnings and instructions marked on the television equipment lf an outdoor antenna is connected to the television equipment be sure the antenna system is grounded so as to provide some protection against voltage surges and static charges For added protection or this television equipment during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna This will prevent damage to the equipment due to lightning and power line surges An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outdoor antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal The mains plug or the appliance coupler is used as the disconnect device the disconnect device shall remain readily operable The mains plug is connected with the electrical outlet with safety ground wire Do not over load wall outlets and extension cords as this can result in fire or electric shock Never push objects of any kind into this television equipment through cabinet slots as they may touch dangerous voltag2. button to enter Picture Mode then press A V but tons to select Dynamic Standard Mild User Brightness Press OK button to enter Brightness then press lt P buttons to adjust the brightness of the picture Contrast Press OK button to enter Contrast then press lt gt buttons to adjust the contrast of the picture Sharpness Press OK button to enter Sharpness then press lt gt buttons to adjust the sharpness of the picture Colour Press OK button to enter Colour then press lt gt buttons to adjust the colour of the picture Press OK button to enter Colour Temp then press A V buttons to select Cold Normal Warm Press OK button to enter Noise Reduction then press A V but tons to select off low middle hight default Colour Temp Noise Reduction 10 sound Adjustment Bass Picture E d Treble Surround Channel a AVL Feature SPDIF 1 Press MENU button on the front panel or MENU button on the remote control to display the main menu 2 Press A V buttons on the remote control or CH buttons on the front panel to select the Sound Setting menu then press OK or gt buttons for the submenu 3 Press A V buttons on the remote control or CH buttons on the front panel to select the item you want to adjust 4 Press OK button on the remote control and press A V lt gt buttons
3. ccccseceeeeeeeee ee 9 ime AGUS eM ec saccteccneceteccees cterecceds 10 Lock AdjuStMen ccccsccseeeeeeeeeees 11 Setup Adjustment ccccceeeeeeeeeeees 12 Media Operation ccccsccseeeeeeeees 13 ROCO ere A E 14 SPeCiPfICATIONS ccceeceeeeeee eee eee eee es 15 TrouDIe SNOOTING cceceeceeeeeeeeeee 16 Overview of the LED TV Congratulation on purchasing the LED Television This product has been designed to provide you with a rich audio and video experience This monitor enables you to watch broadcast cable television or channels connect VCR VCD or DVD play er to watch your favorite movies or connect a computer to use the display as a monitor The TV is equipped with convenient control buttons and a handy remote control to let you adjust the TV setting and customize the TV preferences through an easy to use on screen menu system Features Enjoy the versatility of your LED TV with its wide variety of features eColor active matrix TFT LED TV with remote control eSafe sturdy construction Maximal resolution 32 1366 x 768 Audio Video support HDMI input PC input PC AUDIO input YPbPr input AV input RF input USB input On Screen Display OSD menu system eBuilt in 2 speakers Opening the packing The following section describes the various components of the LED TV Please take a few moments to familiarize yourself with the product and contro
4. Display a variety of information about current channel 12 OK Make sure the adjustment setted previously 113 CH LIST Display the channel list ER Different input source has different functions 15 NICAM Press repeatedly to cycle through the NICAM mode 17 4a Press to scan In reverse HOLD Hold freeze the current teletext page on the screen 18 Pll Press to stop the current program 19 gt gt Press to scan in forword SIZE You can change the picture size in the teletext mode 20 lt lt To play the previous chapter title or track SUBPAGE Display the submenu of the text 21 SOURCE Select the input source 22 REVEAL Display or remove the content that is hidden 23 ASPECT Switch the screen ratio auto 4 3 14 9 zoom1 zoom2 I24 RECALL ISwitch to the previously viewed channel 125 CH Press button to switch the channels 126 REC Press to start recording 21 oLEEP Press the button repeatly to set the time to turn off the TV 128 4 YI gt 4 Direction button 29 EXIT Exit the current menu I30 SUB Start the subtitle mode 31 J Press the button to stop the current program 132 pef To play the next chapter title or track INDEX _ Display a list and information about the teletextpages Using the OSD MENU The On Screen Display OSD menu system provides a quick and simple method to adjust LED TV base setting OSD menu can be viewed using both the
5. device Q VGA Connect to the VGA output of your device Pc AUDIO Connect to the audio output of your PC earphone jack Q YPbPr Connect to the component output of your component device USB Connect to portable USB device such as USB flash hard device RF IN Connect to the UHF antenna or coaxial cable from local TV USB 9000 Remote Control SOURCE 3 TEXT CANCEL REVEAL ASPECT 22 2 23 4 5 24 6 T 25 8 26 9 10 11 21 12 28 1 29 14 15 16 30 17 4 31 18 SIZE SUBPAGE INDEX 19 32 20 Palsonic e If direct sunlight shine directly on the remote sensor remote control s operation may be unstable and the effective range will be shorter Do not hit or violently shake the remote control Never expose the remote control to high temperature or humidity If the remote is not used for an extended period of time remove the batteries to prevent damage or injury from possible battery leakage BUTTON FUNCTIONS 1 POWER Turn the TV on or off 2 TEXT Start the text mode 3 CANCEL Videotext hidden button 4 NUMBER _ Press number keys to enter channel numbers 5 FAV Press to display a list of favorite 16 MUTE Disable the audio output 7 VOL Press button to control the volume up or down l8 EPG Press to display electronic program guide menu 19 TV R Select the TV RADIO mode 110 MENU Enter or exit the OSD menu 111 INFO
6. manufacturer that have the same characteristics as the Original part Unauthorized substitutions may result in fire electric shock or other hazards Note to CATV system installer This note is to remind the CATV system installers that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry practical IF the set is not going to be used for a long period such as during a vacation unplug the set from the wall outlet to economise power If the TV set is plugged in a slight current still flows even with the power button in OFF position Handling the LED screen e Do not leave the LED screen facing the sun as it can damage it Take care when you place the TV by a window e Do not push or scratch the LED screen Do not place a heavy object on the LED screen This may cause the screen to lose conformity or cause LED panel malfunctions e Ifthe TV is used in a cold place a smear may appear on the screen This is not a malfunction The screen will return to normal as its temperature rises to a normal operating level e Ifa still picture is displayed for a long time on the TV screen ghosting may occur for a while The ghosting will eventually disappear e Ifthe LED panel becomes warm during operation this is normal and not a malfunction Handing of broken glass and liquid crystal leakage If the LED panel is damaged crystalline liquid leakage may occur or scattered brok
7. remote control and the control buttons on the front panel Channel Adjustment Channel Management Favorite Management Country Auto Search Digital Manual Search Analogue Manual Search Channel Feature setup T Enter Enter 1 Press MENU button on the front panel or MENU button on the remote control to display the main menu 2 Press A V buttons on the remote control or CH buttons on the front panel to select the Channel Setting menu then press OK or VW buttons for the submenu 3 Press A V buttons on the remote control or CH buttons on the front panel to select the item you want to adjust 4 Press OK button on the remote control and press A V lt gt buttons to change the status 5 Press MENU button to go to the previous menu After changes settings of the OSD menus the new settings are confirmed automatically when OSD picture vanish even did not press the menu to exit the OSD system Sub windows info There are following functions in this page Channel Management To manage Delete Rename Swap Lock Skip all channels Favorite Management To manage Add Delete Favorite channels Country To select country Auto Search To select auto search mode All Digital Analogue Digital Manual Search To search digital channel by entering parameters manually Analogue Manual Search To search analogue channel by entering parameters manually Channel management Channel
8. 00 Viewing angle 176 176 H V TV Functions Tuner 1 Number of channel 100 Standards B G D K Color system PAL SECAM AV Progressive scan y 3 2 2 2 pull down vV Zoom mode Auto 4 3 14 9 Zoom1 Zoom2 Picture mode Dynamic Standard Mild Personal I O ports HDMI input PC input PC audio input YPbPr input AV input RF input USB input SPDIF output Headphone output Other User manual Dimensions W H D Packing size W H D Gross weight Power consumption OSD languages English French Deutsch Italian Spanish Portuguese Sound mode Standard Music Movie Sports Personal Noise reduction y Audio Speaker 2 x 8w Audio mute y Function Return y Audio setting y Auto off y Sleep timer V All specifications are subject to change without notice 19 p pik pe yO 738mmx491mmx 160mm 839mmx584mmx 165mm 16Kg 70w Troubleshooting No power e Make sure the TV and the power cord are connected correctly e Check if you pressed POWER on the remote control unit If the indicator in the front panel is red press POWER in the remote control or the front control panel LED TV does not operate e External influences such as lightning or static electricity may cause improper operation In this case operate the unit after first turning on the power or un plugging the AC cord and plugging it in again after 1 to 2 minutes Power is cut off suddenly e Check if the off
9. Edit Press A V button to select the channel you want to edit Press the red button on the remote control to lock the channel Press the green button on the remote control to delete the channel Press the yellow button on the remote control to skip the channel Press the blue button on the remote control to swap the channel Favorite Management Press the fav button on the remote control to select the programs to be added into favorite list and press RED GREEN YELLOW or BLUE key to mark them Press A V button to select the county that you want Auto Search All Mode Select All item to scan all digital channels carried by current signal mode firstly and then switch to scan all analog channels in selected country automatically User can skip digital search to analog search directly by entering EXIT or MENU key and can also stop auto scan directly by entering EXIT or MENU during analog scanning Digital Mode Select Digital item to search all digital channels in selected country carried by current signal mode User can stop search directly by entering EXIT or MENU key Analog Mode Select Analogue item to search all digital channels in selected country carried by current signal mode User can stop search directly by entering EXIT or MENU key All search mode processing interface display as following Channel Adjustment DTV Ma
10. Paisonic The AUSTRALIAN Company Users Manual TFTV804LED 80cm 31 5 HD LED TV with DVB T a Tu AET a TR a t i a ga i j caf tt oe a Me hee PE ee ee oie oe J ae ae Oe A Ste oe BT aes RECORD SUPER poo USB 20 EDTV ure foech WXGA faena FS Digital Broadcasts electronic program guide PC input Lock MS SORE READ Where available Offering Australians quality since 1958 www palsonic com au rtant safety int ti carn U Haier as This symbol is intended to tell the user RISK OF ELECTRIC that parts inside the product pose a SHOCK DO NOT OPEN risk of electric shock to persons CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL CAUTION This symbol is intended to tell the user that important operating and servicing instructions are described here Grounding information This apparatus must be grounded To ensure safe operation the grounded plug must be inserted only into a standard grounded power outlet which is effectively grounded through normal household wiring Extension cords used with the equipment must be hazardous The face that the equipment operates satisfactorily only means it is grounded but the installation may not necessarily be safe For your safety if in any doubt about the effective grounding if the equipment or power outlet please consult a qualified techn
11. e points or short circuit internal parts This could result in a fire or electric shock Never spill liquid of any kind in the television equipment Do not attempt to service this television equipment yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Unplug this television equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions When the power cord or plug is damaged or frayed lf liquid has been spilled into the television equipment If the television equipment does not operate normally by following the operating instructions Adjust only those control that are covered by the operating instruction as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the television equipment to normal operation If the television equipment has been dropped or the cabinet has been damaged When the television equipment exhibits a distinct change in performance this indicates a need for service UP on completion of any service or repairs to this television equipment ask the service technician to perform routine safety checks to determine that the television is in safe operating condition When replacement parts are required make sure that the service technician has used replacement parts specified by the
12. en glass may result Do not touch broken glass or crystalline liquid which is toxic With bare hands that have cuts skin irritation or poisoning may result If any crystalline liquid gets into mouth or eyes rinse thoroughly with and consult your doctor IMPORTANT NOTICE This product composes up to 6 0 million cells and a few cell defects may occur In the manufacture of the panel Several dead pixels allow up to 2 bright or 2 dark pixels on the panel are deemed acceptable by the industry standards In line with manufacturers and would not mean that the panel is faulty Dead pixels panels with 6 pixels or more within 12 month period Palsonic Corporation Pty Ltd complies with industry standard and reserves the right to repair the unit and non refundable We hope you will understand that the product that corresponds to this standard is regarded as acceptable Table of Content Overview of the LED TV 1 FOAtLUICS cccccecceceeceececeeeeeeeeeeeneeeenes 1 Opening the packing ccccccee eee 1 Product components ccceceeeee ees 2 Side WAC WY scteceiersinectsputninavedineittenieamsaundasonines 2 Rear VIC W ccintescnadsrceusteonseevaadundusadmenteatavenss 3 Remote COMMON cece 255 cece eeeutiateeran esieces 4 Using the OSD menu 0068 6 Channel Adjustment ccccccceeeees 6 Picture Adjustment cccccseeeeeeeee 8 Sound Adjustment
13. er the maim unit Do not carry the TV by its speakers Both the base and the speakers could come off causing you to drop the TV possibly resulting in damage to the TV or causing injury Television equipment and cart combination should be moved with care Quick stops excessive force and uneven surfaces when moving may cause the equipment and cart combination to overturn Shelf mounting should follow the manufacturer s instructions and should use a mounting kit approved by the manufacturer Slots and opening in the cabinet and the back or bottom are provided for ventilation To ensure reliable operation of the television equipment and to protect it from overheating these opening must not be blocked or covered This television equipment should not be placed in an enclosed installa tion such as a bookcase unless proper ventilation os provided The openings should never be covered with a cloth or other material and the bottom openings should not be blocked by placing near or over a radiator or heat source This Television equipment should be operated only from type of power source indicated on the marking label If you are not sure of the type of power supplied to your home consult your television dealer or local power company As a Safety feature this television equipment is equipped with a grounded power plug If the plug does not fit in your power outlet contact your electrician Do not modify the plug and defeat this safety feature
14. ff Reset TV Setting Reset to default setting Software Update Using the USB device to update sofeware 13 Media OPERATION Note Before operating Media menu Plug in USB device then press INPUT button to set the Input Source to Mdeia 1 Press W A button to select Media inthe Source menu then press OK button to enter 2 Press lt q gt button to select the option you want to adjust in the main menu then press OK button to enter Sub windows info PHOTO Press q p button to select PHOTO in the main menu then press OK button to enter select the file you want to watch Press menu button to return back to the previous menu and Exit button to quit MUSIC Press q p button to select MUSIC in the main menu then press OK button to enter select the file you want to watch Press menu button to return back to the previous menu and Exit button to quit Press q p button to select MOVIE in the main menu then press OK button to enter Select the file you want to watch Press menu button to return back to the previous menu and Exit button to quit e Book Press q p button to select e Book in the main menu then press OK button to enter select the file you want to watch Press menu button to return back to the previous menu and Exit button to quit 14 Specifications Display Active screen size 31 5 inches Aspect ratio 16 9 Response time 7ms Resolution 1366 768 Contrast 4000 1 Brightness 2
15. ician WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE TO AVOID ELECTRIC SHOCK INSERT TPLUG FULLY INTO THE POWER OUTLET Product disposal Do not dispose of the TV with general household waste The LED screen contains a small amount of liquid crystal and mercury For disposal or recycling information please contact your local authorities Safety precautions Please read all of these instructions before you operate your television and save these instructions for later use This unit has been engineered and manufactured to ensure your personal safety However improper use can result in electric shock or fire hazards In order not to defeat the safeguards incorporated in this equipment please observe the following basic rules for its installation use and servicing Unplug this television equipment from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a soft cloth moistened with water for cleaning Use only the attachments recommended by the television equipment manufacturer Do not use this television equipment near water for example near a bath tub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool Do not place this equipment on an unstable surface stand or cart The television equipment may fall causing serious injury to a child or an adult and seriously damage the equipment When carrying the TV hold it und
16. indows info Lock Press OK button to enter Lock The Lock sub page includes four parts Lock Enable Parental Guidance Change Pin Code Hotel Mode Language Press OK button to enter Language then press A V to select Language that you want Clock Press lt P gt to check out the current system time and set time zone DST Sleep Timer Press OK button to enter Sleep Timer Then press A V buttons to set sleep timer Off 10 Mins 20 Mins 30Mins 60Mins 90 Mins 120 Mins 180 Mins 240 Mins Auto Power Off Press OK button to enter Auto Power Off then press A V but tons to set auto standby off 1H 2H 4H Hearing impared Press A to select Hearing impares On or Off 12 1 Press MENU button on the front panel or MENU button on the remote control to display the main menu 2 Press A V buttons on the remote control or CH buttons on the front panel to select the Setup Setting menu then press OK or gt buttons for the submenu 3 Press A V buttons on the remote control or CH buttons on the front panel to select the item you want to adjust 4 Press OK button on the remote control and press A V lt gt buttons to change the status 5 Press MENU button to go to the previous menu Sub windows info OSD Timer Press A Wbutton to select OSD Timer 5 10 15 20 25 30 Seconds PC Setup set PC Only available in PC source Blue Screen Select Blue Screen mode between On and O
17. l panel before using it When you unpack this LED TV make sure the box contains the following items LED Color Television Remote Control with batteries User Manual Warranty Registration Card Quick Start Guide If any of these items appears to be missing or damaged please contact your vendor or authorised service personnel for assistance Product components Front view IR Receiver A soft blue light illuminates when the television power is on Remote Inductor and Power Indicator POWER Turn the TV on or off INPUT Switch the input sources MENU Press the button to enter on screen Display OSD CH Increase or decrease channel numbers O VOL Increase or decrease the volume Back view ee A Component VGA AUDIO L Y Pb a RF IN f amp 2 ow QC spor Ly 1 HDMI1 HDMI2 DO E 4 Oo HEADPHONE Connect a stereo headphone 3 5mm for private listening SPDIF Connect an optional coaxial digital cable not included through a compatible amp receiver to enjoy superior audio sound AV IN Connect to the audio and video output of A V device HDMI 1 2 3 IN Connect to the HDMI output of your
18. nual Search y Frequency KHz 474000 ay BandWidth MHz Picture Sound hamei eh O y og Feature duty eee Owe Setup select channel number by RIGHT key or entering number directly The strength and the quality as shows Press ENTER key on Start item to start current channel search The manual searching UI and the auto searching UI are the same ATV Manual Search ATV Manual Search Analog Parameters Value Default Current Channel 001 100 Frequency Show the Frequency when srech Frequency of the current channel Search Press the button enter to open the search sub page Fine Tune Press the button enter to open the fine tune sub page Color System Auto PAL SECAM Color System of the current channel sound System Sound System of BG DK I L L the current channel Picture Adjustment 1 Press MENU button on the front panel or MENU button on the remote control to display the main menu 2 Press A V buttons on the remote control or CH buttons on the front panel to select the Aicture Setting menu then pressOK or gt buttons for the submenu 3 Press A V buttons on the remote control or CH buttons on the front panel to select the item you want to adjust 4 Press OK button on the remote control and press A V lt gt buttons to change the status 5 Press MENU button to go to the previous menu Sub windows info few Mode Press OK
19. timer or sleep timer are set e The unit s internal temperature has increased Remove any objects blocking the vents and clean them to remove dust Remote control unit does not operate e Check if the batteries are inserted with the polarity correctly aligned e Check if the batteries are discharged Please replace with new batteries e Make sure that you do not use the remote control under strong or fluorescent lighting Check if there is a fluorescent light illuminated near the remote control sensor The path of the remote control beam may be blocked please make sure the path is clear and that remote control is aimed at the remote control sensor in the TV Picture is cut off with side bar screen e Check if the image position is correct e Check if the screen mode adjustments such as picture size are made correctly strange color light color or color misalignment e Is the room too bright The picture may look dark in a room that is too bright e Check the input signal setting 16 Palsonic The AUSTRALIAN Company Palsonic Customer Service Telephone Australia 1300 657 888 Palsonic Corporation Pty Ltd ABN 34 000 474 108 1 Joynton Avenue Waterloo NSW 2017 Australia Telephone 02 9313 7111 Facsimile 02 9697 0655 www palsonic com au
20. to change the status 5 Press MENU button to go to the previous menu Sub windows info Sound Mode Press OK button to enter Sound Mode then press A V buttons to select Standard Movie Music Speech User Off Bass Press OK button to enter Bass then press lt P gt buttons to adjust the low frequency content of audio output Treble Press OK button to enter Treble then press lt gt buttons to adjust the high frequency content of audio output Balance Press OK button to enter Balance then press lt gt buttons to adjust the audio output between left and right speakers Surround Press OK button to enter Surround then press A V buttons to adjust Surround mode On Off AVL Press A V button to adjust AVL mode On Off SPDIF Press A V button to adjust SPDIF mode Auto Off PCM 11 Feature Adjustment 1 Press MENU button on the front panel or MENU button on the remote control to display the main menu 2 Press A V buttons on the remote control or CH buttons on the front panel to select the Feature Setting menu then press OK or gt buttons for the submenu 3 Press A V buttons on the remote control or CH buttons on the front panel to select the item you want to adjust 4 Press OK button on the remote control and press A V lt gt buttons to change the status 5 Press MENU button to go to the previous menu Sub w
Download Pdf Manuals
Related Search