Suspension Kit User Manual
Contents
1. use washers 3 Tighten the eyebolt until the shoulder is snug against the enclosure Continue to rotate Figure 5 the eyebolt until it reaches the desired position 2010 QSC Audio Products LLC All rights reserved QSC and the QSC logo are registered trademarks of TD 0003 18 00 A QSC Audio Products LLC in the U S Patent and Trademark office and other countries Tilt Direct DMT Intrinsic Correction DEEP and GuardRail are all trademarks of QSC Audio Products LLC All other trademarks are the property of their respective owners Patents may apply or be pending CLASSIFICATION CONFIDENTIAL AUTHORIZED QSC PARTNERS WITH Paper Document Status PRODUCTION QSC Digital2. KW Series SUS KIT 122 User Manual QS Contents Contents Pull Back Bar KW122 1 each M10 Lock Washer 1 each M10 Eyebolt 3 each M10 Flat Washer 2 each KW122 Pull Back Gasket 1 each M10 Button Head Hex Socket Screw 1 each M10 Nut 1 each Instruction Sheet KW SUS KIT 122 1 each This suspension kit is required for horizontal suspension of the QSC KW122 Loudspeaker System This kit can also be used to suspend the KW122 KW152 or KW153 Loudspeaker Systems vertically and the KW152 and KW153 horizontally All loudspeaker systems must be suspended from a solid structure This kit contains hardware to suspend one loudspeaker system IMPORTANT SAFETY PRECAUTIONS AND EXPLANATION OF SYMBOLS Ady warnine AA Install in accordance with QSC Audio Product s instructions and under the supervision of a licensed Professional Engineer Before placing installing rigging or suspending any speaker product inspect all hardware suspension enclosures transducers brackets and associated equipment for damage Any missing corroded deformed or non load rated component could significantly reduce the strength of the installation or placement Correct any such condition immediately so as not to severely reduce the safety of the installation Use only properly rated hardware for the loading conditions of the installation and any possible short term unexpected overloading Never exceed the rating of the hardware or equipment Consult a licen
3. al damages This warranty gives you specific legal rights This limited warranty is freely transferable during the term of the warranty period The warranty on QSC products is NOT VALID if the products have been purchased from an unauthorized dealer online e tailer or if the original factory serial number has been removed defaced or replaced in any way Damage to or loss of any software or data residing on the product is not covered When providing repair or replacement service QSC will use reasonable efforts to reinstall the product s original software configuration and subsequent update releases but will not provide any recovery or transfer of software or data contained on the serviced unit not originally included in the product Customers may have additional rights which vary from state to state or from country to country In the event that a provision of this limited warranty is void prohibited or superseded by local laws the remaining provisions shall remain in effect Periodically this warranty is updated To obtain the most recent version of QSC s warranty statement please visit www qscaudio com Contact us at 800 854 4079 or visit our website at www qscaudio com The QSC limited warranty is valid for a period of three 3 years from date of purchase in the United States and many but not all other countries For QSC warranty information in countries other than the United States contact your authorized QSC international distribu
4. e a 6 mm hex wrench to remove the M10 flat head screw located at the rear of the enclosure just below the amplifier module 2 Thread an eyebolt into the threaded insert just below the amplifier module Do not use a washer 3 Tighten the eyebolt until the shoulder is snug against the enclosure Continue to rotate the eyebolt until it reaches the desired position Important Do not use any washers or the Pull Back Bar when vertically suspending the KW122 loudspeaker CLASSIFICATION CONFIDENTIAL AUTHORIZED QSC PARTNERS WITH Paper Document Status PRODUCTION QSC Digital CLASSIFICATION CONFIDENTIAL AUTHORIZED QSC PARTNERS WITH Horizontal Suspension Figure 2 When suspending the KW122 in a horizontal position you must install the Pull Back Bar and two eyebolts in one of the side panels Tools Required e 6mm Hex Wrench Allen Wrench e 7mm Open End Box End Wrench Parts Required e Pull Back Bar KW122 1 e M10 Eyebolt 3 e KW122 Pull Back Gasket 1 M10 Nut 1 M10 Lock Washer 2 e M10 Flat Washer 2 e M10 Button Head Hex Socket Screw 1 Horizontal Suspension Figure 2 The Pull Back Bar attaches to the same M10 installation location as shown regardless of which side the LF Driver is on NOTE If you are suspending the KW122 in the direction opposite of what is shown e The Pull Back Bar is installed in the same place as shown e The Eyebolt is installed in
5. losure Continue to rotate the eyebolts until they reach the desired position back eyebolt Install One Pull Back Eyebolt Figure 4 1 Using a 6 mm hex wrench remove the M10 flat head screw located at the rear of the enclosure just below the amplifier module NOTE You can optionally use the threaded insert just above the amplifier module for the pull back eyebolt 2 Thread an eyebolt into the enclosure s threaded insert do not use a flat washer or standoff on the pull back eyebolt 3 Tighten the eyebolt until the shoulder is snug against the enclosure Continue to rotate the eyebolt until it reaches the desired position Horizontal Suspension Tools Required e 6mm Hex Wrench Allen Wrench Parts Required e M10 Eyebolt 3 Install Two Top surface Eyebolts Figure 5 1 Use a 6 mm hex wrench to remove the two factory installed M10 flat head screws from the side top of the loudspeaker enclosure This side becomes the top 2 Thread one eyebolt into each of the two threaded inserts on the top side of the loudspeaker enclosure Do not use washers 3 Tighten the eyebolts until their shoulders are snug against the enclosure Continueto 4 rotate the eyebolts until they reach the desired position Install One Pull Back Eyebolt 1 Use a6 mm hex wrench to remove the M10 flat head screw located at the rear of the enclosure just above the amplifier module 2 Thread an eyebolt into the threaded insert Do not
6. ock washer and flat washer Tighten until the split lock washer is flattened Install Two Top surface Eyebolts Figure 2 1 Use a6 mm hex wrench to remove the two factory installed M10 flat head screws from the side top of the loudspeaker enclosure This side becomes the top Oe Figure 3 2 Thread one eyebolt into each of the two threaded inserts on the top side of the loudspeaker enclosure Do not use washers 3 Tighten the eyebolts until their shoulders are snug against the enclosure Continue to rotate the eyebolts until they reach the desired position 2 Paper Document Status PRODUCTION QSC Digital KW152 and KW153 Loudspeaker System The KW152 and KW153 can be suspended vertically with the LF Driver on the top or bottom The following instructions apply to either orientation Vertical Suspension Tools Required 6 mm Hex Wrench Allen Wrench Parts Required M10 Eyebolt 3 Install Two Top surface Eyebolts Figure 4 1 Use a 6 mm hex wrench to remove the two factory installed M10 flat head screws from the top of the loudspeaker enclosure 2 Thread one eyebolt into each of the two threaded inserts on the top of the loudspeaker enclosure Do not use washers 3 Tighten the eyebolts until their shoulders are snug against the enc
7. sed Professional Engineer regarding physical equipment installation Ensure you understand and adhere to all local state and national regulations regarding the safety and operation of equipment Use only load rated hardware to attach to the eyebolts or Pull Back Bar when suspending these products Do not suspend these products from any structural element on the loudspeaker enclosure other than the load rated M10 suspension points as described in this document Use proper lifting techniques technologies Safety Precautions and Explanation of Terms and Symbols WARNING The term WARNING indicates instructions regarding personal safety If the instructions are not followed the result may be bodily injury or death CAUTION The term CAUTION indicates instructions regarding possible damage to physical equipment If these instructions are not followed it may result in damage to the equipment that may not be covered under the warranty IMPORTANT The term IMPORTANT indicates instructions that are vital to the successful completion of the operation NOTE The term NOTE is used to indicate additional useful information The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operation and mainte nance servicing instructions in this manual The intent of the lightning flash with arrowhead symbol in a triangle is to alert the user to the presence of un insulated dangero
8. the as shown in the alternate installation Figure 3 e The two top Eyebolts are installed in the same positions but on the other side of the enclosure Figure 2 1 Remove the factory installed M10 flat head screw from the side of the enclosure to which the Pull Back Bar is to be attached 2 Test fit the Pull Back Bar attachment washers and gaskets to ensure proper assembly prior to sticking self adhesive gasket to Pull Back Bar 3 Attach the Pull Back Gasket to the Pull Back Bar by peeling off the adhesive backing and pressing the adhesive side to one end of the Pull Back Bar Ensure that the hole in the gasket aligns with the hole in the Pull Back Bar 4 Install one M10 Lock Washer then one M10 Flat Washer onto the M10 Hex Socket Button head screw 5 Insert the screw into the Pull Back Bar through the hole with the gasket from the opposite side of the Pull Back Bar from the gasket The gasket goes between the Pull Back Bar and the loudspeaker enclosure 6 Using a 6 mm hex wrench bolt the Pull Back Bar to the enclosure with the screw and two washers Before tightening fully ensure the Pull Back Bar is perpendicular to the edge of the enclosure Tighten the screw until the split lock washer is flattened 7 Insert the eyebolt into the Pull Back Bar The eye of the eyebolt must be oriented toward the two top eyebolts installed in the enclosure Attach the eyebolt to the Pull Back Bar with hex nut l
9. tor A list of QSC International distributors is available at www gscaudio com To register your QSC product online go to www qscaudio com and select Product Registration Other questions regarding this warranty can be an swered by calling e mailing or contacting your authorized QSC distributor 2010 QSC Audio Products LLC Patents may apply or be pending QSC is a registered trademark of QSC Audio Products LLC QSC and the QSC logo are registered with the U S Patent and Trademark Office All trademarks are the property of their respective owners KW122 Loudspeaker System The KW122 Loudspeaker System can be suspended in both vertically and horizontally The horizontal orientation allows you to suspend the loudspeaker with the LF Driver to the left or right and requires the installation of a Pull Back Bar Vertical Suspension Tools Required 6 mm Hex Wrench Allen Wrench Parts Required e M10 Eyebolt 3 Install Two Top surface Eyebolts Figure 1 1 Use a 6 mm hex wrench to remove the factory installed M10 flat head screws from the top of the loudspeaker enclosure Figure 1 2 Thread an eyebolt into the two threaded inserts on the top of the loudspeaker enclosure Do not use washers 3 Tighten the eyebolts until their shoulders are snug against the enclosure Continue to rotate the eyebolts until they reach the desired position Install One Pull Back Eyebolt Figure 1 1 Us
10. us voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans KW122 KW152 KW153 Weight Net 49 Ibs 22 2 kg 62 Ibs 28 1 kg 87 Ibs 39 5 kg Warranty USA only other countries see your dealer or distributor Disclaimer QSC Audio Products LLC is not liable for any damage to amplifiers or any other equipment that is caused by negligence or improper installation and or use of this loudspeaker product CLASSIFICATION CONFIDENTIAL AUTHORIZED QSC PARTNERS WITH Paper Document Status PRODUCTION QSC Digital QSC Audio Products 3 Year Limited Warranty QSC Audio Products LLC QSC guarantees its products to be free from defective material and or workmanship and will replace defective parts and repair malfunctioning products under this warranty when the defect occurs under normal installation and use provided the unit is returned to our factory one of our authorized service stations or an authorized QSC International Distributor via pre paid transportation with a copy of proof of purchase Le sales receipt This warranty provides that the examination of the return product must indicate in our judgment a manufacturing defect This warranty does not extend to any product which has been subjected to misuse neglect accident improper installation or where the date code has been removed or defaced QSC shall not be liable for incidental and or consequenti
Download Pdf Manuals
Related Search