Home
General Set-up Functions LFO1 LFO2 Reset
Contents
1. General The DUAL LFO module offers two independent Low Frequency Oscillators These primarily function as modulation sources for oscillators VCO filters VCF or amplifiers VCA Each LFO is voltage controllable offers three waveforms and a retrigger function Set up DUAL LFO is fully compatible to Doepfer s A 100 modular system in size bus power and CV Gate voltage Connect the 10 pin cable to a corresponded 16 pin jack on the Doepfer mainframe bus Supply voltage needs to be 12 volts 5 volt connections are not required The wattage is 30 mA the module size 8 TE Teileinheiten or 40 mm ATTENTION Please check for correct polarity The colored side of the connector cable needs to point downwards so that the cable is not twisted Functions LFO1 LFO1 the module s upper half offers manual speed control by Ratel Its frequency speed ranges from 0 1 Hz which equals approximately ten seconds for a full amplitude pass up to 100 Hz Speed can also be controlled by input CV1 with corresponding attenuator This input requires voltages between 5 to 5 volts This input provides two functions e continuous speed control for LFO1 e progression degression of the maximal minimal speed by a factor of 30 using an appropriate static CV source Here the maximum speed reaches widely into the audible frequency range to 3000 Hz An appropriate control voltage source would be the keyboard s pitch wheel output CV or MIDI to CV con
2. c changes of a control signal can be achieved e g by controlling LFO1 s rate by LFO2 s sample amp hold signal Likewise two slightly tempo differing inter modulating triangle waveforms can result in a more lively modulation compared to a static LFO Try this next time you need a vibrato effect The LFO outputs will need to be externally mixed and applied with slight amount to the destination Reset Both LFOs offer individual Reset inputs Any appropriate trigger or gate signal between 5 to 12 volts force the waveform to restart By matching the rate control and by applying a separate reset impulse at musical intervals e g every second bar it is possible to manually synchronize the LFO to a sequencer Hint Reset only reacts to the descending slope of a trigger gate signal Hint Using the reset input allows LFO to be used as a simple envelope generator Suitable waveforms for this application are descending saw tooth and triangle with slow to medium speeds The LFO speed will need to be adjusted to the note length This avoids unwanted restarts while the note is being held On the other hand these repeat effects may also be used to create rhythmic sound effects pr 7 Operating Manual DUAL LFO Module
3. verted CV1 is internally connected to LFO2 s output Therefore the speed of LFO1 can be directly controlled by LFO2 without any patching This prewiring is disconnected when input CV1 is patched LFO1 offers three waveform shapes selected by Wavel switch e descending saw tooth e triangle e square The output of LFO1 is available at Out1 LFO2 LFO2 the module s upper half offers manual speed control by Rate2 Its frequency speed ranges from 0 1 Hz which equals approximately ten seconds for a full amplitude pass up to 100 Hz Speed can also be controlled by input CV2 with corresponding attenuator This input requires voltages between 5 to 5 volts This input provides two functions e continuous speed control for LFO2 e progression degression of the maximal minimal speed by a factor of 30 using an appropriate static CV source Here the maximum speed reaches widely into the audible frequency range to 3000 Hz An appropriate control voltage source would be the keyboard s pitch wheel output CV or MIDI to CV converted CV2 is internally connected to LFO1 s output Therefore the speed of LFO2 can be directly controlled by LFO1 without any patching This prewiring is disconnected when input CV2 is patched LFO2 offers three waveform shapes selected by Wave2 switch e ascending saw tooth e triangle e Sample amp Hold The output of LFO2 is available at Out2 Hint The LFOs can modulate one another By this drasti
Download Pdf Manuals
Related Search
Related Contents
Por favor haga clic aquí para descargar manual de Instalación y Smeg FS67MFX Instruction Manual Tanaka TPE-2501 User's Manual H33/HB4丿 載ーナー ロ 製品寸法 ロ 取付け必要スペース Instruction Manual Manuel d`instructions Manual de instrucciones Manual del usuario G 500S- 32, G500S-64 NO TI FIER ITA LIA Cub Head User Manual Issue 1.0.cdr 2 cu. ft. (TOW) Copyright © All rights reserved.
Failed to retrieve file