user manual
Contents
1. power on off WF833F WF833 continuously for 3 times otherwise the UIM card may be blocked 14 3 Basic Operations 3 1 Making a Call 3 1 1 Making a Domestic Call Connect WF833F WF833 to audio frequency phone through PHONE FAX interface Enter the telephone number add area code when making a long distance call on the audio frequency phone after you hook off wait for 10 seconds to send it automatically or press the key on the phone to send the call directly Note When RSSI indicator turns red and there is no dialing tone when picking up the audio frequency phone s earpiece it indicates weak RF signal or loosen antenna screw Change the position of the terminal or check the antenna installation 3 1 2 Making an International Call Enter the code of the country you want to dial and the complete telephone number wait for 10 seconds to send it automatically or press the key on the phone to send the call directly Delete 0 before the area code when you make a call 3 1 3 Adjust the Volume during Calling During conversation you can press and key continuously and quickly to adjust the volume press key to increase the volume and key to decrease the volume The volume has 4 levels 3 2 Answering a Call When the phone rings pick up the earpiece to answer If the phone has hands free function 15 you can also answer the call by pressing the hands free key End the call by pressing hands free key again Make sure to2. It is highly recommended to charge the battery before initial use The battery might have been discharged during storage and delivery Keep the length of line between WF833F WF833 and phone less than 3 meters when it is connected to outer telephone Do not unplug the connector of the data cable from WF833F WF833 when the power is on 1 3 Cleaning and Maintenance The WF833F WF833 is not water resistant so do not use it in high humidity places such as the bathroom If you want to clean your WF833F WF833 please use clean fabric that is a bit wet or anti static Turn off your WF833F WF833 before you clean it Do not use chemical cleaning solvents or strong detergents to clean your terminal such as alcohol dilution agent and benzene Use the terminal within a temperature range of 10 C 55 C and humidity less than 95 Do not use your WF833F WF833 during thunderstorm Do not take out your UIM card if there is no necessary The damaged or lost of UIM card may cause difficulty in maintenance of the terminal 1 4 Limited Warranty This warranty does not apply to defects or errors in the Product caused by a Reasonable abrasion b End User s failure to follow ZTE s installation operation or maintenance instructions or procedures c End User s mishandling misuse negligence or improper installation disassemble storage servicing or operation of the Product Modifications or repairs not made by ZTE or a ZTE certified
3. dealing with data service or fax e RSSI Indicator Yul Indicator turns green when RF signal is normal Indicator turns yellow when RF signal is weaker Indicator turns red when there is no RF signal 2 3 2 Switch The 1 is used to power on or power off WF833F WF833 Switch to I side to power on switch to O side to power off 11 2 4 Interface and Installation 2 4 1 Interface Description 1 Antenna ANT 2 Data interface DATA 3 Phone Call meter Fax interface PHONE FAX Note The WF833 do not support FAX function 4 External power socket 5 Power toggle switch 2 4 2 Installation 1 Connect the Audio frequency phone to the PHONE interface 2 Install the antenna to the antenna connector Hold the stick of the antenna and rotate the screw cap in clockwise direction Do not rotate antenna directly 12 3 X Open the UIM card cover at the bottom of the terminal Slide the UIM card into the UIM card slot Make sure that the metal connector is facing downwards 4 Good grounding may guarantee your WF833F WF833 work reliably 5 Connect the adaptor to outer power and plug the plug to the socket at the real of the terminal 6 Switch to I side to power on WF833F WF833 Make sure the phone is on hook before powering on Note The prompt of shut down will not be heard while the terminal is power off if a new call comes in 2 5 Battery There are two ways of power supply 1 External pow
4. exit from the hands free mode to guarantee next call can come in 3 3 Call Metering Connect the call meter s interface to PHONE FAX interface of WF833F WF833 and then con nect the phone to the call meter Call meter will begin to count when the phone is connected successfully The default setting of WF833F WF833 supports reversal metering and 16 KHz pulse metering If WF833F WF833 can not meter you can try to follow the instructions below to switch metering model If it is 12 KHz pulse call meter hook off the phone key in 983 7083 with a sound of confirmation If it is factory default call meter for WF833F WF833 hook off the phone key in 983 7080 with a sound of confirmation Restart WF833F WF833 when you make use of instructions to switch metering model Note This function is network dependent the rate of metering should be set at the outer call meter 3 4 Other Functions WF833F WF833 supports call forwarding call waiting and three way call Contact the network carrier for details Note This function is network dependent 16 4 G3 Fax This function is only available to the WF833F SAMSUNG BROTHER CANNON PANASONIC and LEXMARK FAX machine are recommended It may need a long time to receive or send fax wait for a moment after indicator D lighting up In the process of faxing the power should be sufficient As usual it is recommended to use external power supply Connect G3 Fax machine to FAX interface of WF8
5. fax if errors occur such as wrong destination number error sending error receiving hook on the receiver till ppp and m indicator turn off and then do next step gt This function needs network support and is activated with the number 18 5 Access Internet WF833F WF833 supports Internet access through data cable Make sure the data cable is connected well with computer and WF833F WF833 The dial up software is embedded in WF833F WF833 and will be installed automatically when connected well with computer If the dial up software automatic installation process failed you can find a virtual disk drive that created by WF833F WF833 run the setup exe file to install the dial up software To access network select Start gt Programs Fixed CDMA Dial up Tool a Dial up dialogue box appears as described in the following figure de TE DI TR Gn Meme Deg ute 4777 Core Type user name password and phone number which are provided by your service provider and then click Connect 19 If the authentication process is succeed one dial up connection will be established Connec tion status icons will be created at the lower right corner of your computer screen as shown below Ly Diel Up Lapoert pras telly Run web browser and type web address in the address bar To disconnect from the network right click the icon and select Disconnect as shown blow Open Exit 5 Note This function is network dependen
6. 33 may interfere with medical devices like hearing aids and pacemakers Consult a physician or the manufacturer of the medical device before using the WF833F WF833 Be aware of the usage limitation when using WF833F WF833 at places such as oil ware houses or chemical factories where there are explosive gases or explosive products being processed because even if your terminal is in idle state it still transmits radio frequency RF energy Do not touch the antenna while calling Keep the antenna free from obstructions and position the antenna straight up This will ensure best call quality Please put the WF833F WF833 on the safe place It may cause injury if used as a toy by children Do not put other things on the WF833F WF833 to avoid overlaying radiator Please use original accessories or accessories that are authorized by ZTE Using any unauthorized accessories may affect your WF833F WF833 performance hurt your termi nal or even cause danger to your body and violate related national regulations about telecom terminals As your WF833F WF833 can produce electromagnetic field do not place it near magnetic items such as computer disks Do not expose your WF833F WF833 to direct sunlight or store it in hot areas High tem peratures can shorten the life of electronic devices Prevent liquid from leaking into your WF833F WF833 Do not attempt to dismantle the WF833F WF833 by yourself Non expert handling of the devices may damage them
7. 33F by ordinary phone line before using G3 fax Note Do not connect G3 Fax machine and phone to WF833F simultaneously Otherwise sending or receiving fax will be in abnormal Set the G3 Fax machine as below before receiving or sending fax Speed Under 14400 suggest to use 9600 bps Quality of sending Standard ECM OFF Sending G3 Fax Both of WF833F and G3 Fax machine are power on and in state of default standby mode Hook off the Fax machine key in the number press the send key of G3 Fax machine to send the fax M Sir Nes 17 Note gt Send no more than 3 pages each time under the wireless network gt When D indicator blinking it showing WWF833F is create a connection with the other part It links with other part successfully with D indicator lighting up and then WF833F starts to send fax If D indicator turns off operate again gt When WF833F is sending or receiving fax do not do any other operation e Receiving G3 Fax 1 Both of WF833F and G3 Fax machine are power on and in state of default standby mode 2 Set G3 Fax machine in auto receiving mode to receive fax Note gt Ifthe network do not support auto receiving pick up the receiver of G3 Fax machine key in 8 to set WF833F as Fax mode with a sound of confirmation Then you can receive or send fax In the Fax mode you can not make or answer a call You need to key in O to set WF833F back to default voice mode gt When you receiving or sending
8. ZTE WF833F WF833 CDMA Fixed Wireless Terminal User Manual LEGAL INFORMATION Copyright 2011 ZTE CORPORATION All rights reserved No part of this publication may be excerpted reproduced translated or utilized in any form or by any means electronic or mechanical including photocopying and microfilm without the prior written permission of ZTE Corporation The manual is published by ZTE Corporation We reserve the right to make modifications on print errors or update specifications without prior notice Version No R1 1 Edition Time Mar 2011 Manual No 079584502083 1 General Information Contents US We LZ Safety Precautions e dE 5 1 3 Cleaning and Maintenance fail 1 4 Limited Warranty EE 7 1 07 Limitation of Liability 24 3 26s Atal e aout 8 Getting Started 2 1 Unpacking 2 27 Technical Parameters cional acta 9 2 3 Appearance 2 3 1 LED Indicator PA EL E 2 4 Interface and Installation 2 4 1 Interface Description 2 42 Install ooo EE Ee 25 Battery ae 2 6 About UIM Card Leet ERT Rer Te WEE 2 6 2 Usage of UIM Card 3 BASIC E E 15 N Making sellegen uh eae eta Uh a T 15 3 1 1 Making a Domestic Call oooooocoooncccinncconococococccnoconononcnonnnnonano naar ncnnnrnnnnnn 15 3 1 2 Making an International Call sneenneeneeeeieeseneerserestrnssrnstrrsrnnssrrnrrrnrernne 15 3 1 3 Adjust the Volume during Calling ses
9. a Phone cord User manual Certificate of quality Data cable 1 optional 2 2 Technical Parameters Air Interface Protocol 15 2000 downward compatible with S 95A B Frequency Range TX 824 849MHz RX 869 894MHz LED Display Power indicator Battery indicator Off hook indicator DATA FAX indicator RSSI signal strength indicator External Interface External power socket Data interface DATA Antenna connector ANT Phone Call meter Fax interface PHONE FAX Voice Decoding 8K EVRC Dimensions LxDxH 195 mmx132 4 mmx38 mm Exclude antenna Battery Continuous Standby Time Approx 25 hours Continuous Talk Time Approx 2 hours Standby Time and Talk Time depending on the network con dition Note Please refer to the real objects for the related parameters about the battery and charger 2 3 Appearance 10 2 3 1 LED Indicator e Power Indicator ch Indicator lights up when WF833F WF833 is connected well to the external power outlet e Battery Indicator BAT Indicator lights up when WF833F WF833 is power supplied by battery Indicator blinks when the battery is in low voltage Note WF833F WF833 may not work normally when the battery is in low voltage e PHONE Indicator ppp Indicator lights up when the phone is hook off it turns off when the phone is hook on e DATA FAX Indicator 4 Indicator lights up when WF833F WF833 is
10. e 15 3 2 Answeringia Call a de el oda as eb a 15 33 Gall Metering coi ide 16 31d Other FUNCIONS msi 16 A AA A E 17 5 Access linternet iiscccicccccscsccscccsselencosevescctsnecsvecnseisoaaesscscaussacesanndetsonsesscocetsoacisecseaiseaadsansa 19 5 Troubleshooting TTT 21 1 General Information 1 1 Welcome Thank you for choosing ZTE WF833F WF833 CDMA Fixed Wireless Terminal FWT To guar antee your WF833F WF833 always in its best condition please read this manual carefully The pictures symbols and contents in this manual are just for your reference They might not be completely identical with your WF833F WF833 Please subject to the material object ZTE operates a policy of continuous development We reserve the right to update the technical specifications in this document at any time without prior notice Note There are two ZTE WF833F WF833 models One needs UIM card inserted in and the other does not need If the section or function in this manual is marked with xk it indicates that this section or function is only available to the model with UIM And the other functions are available to both models 1 2 Safety Precautions e Some electronic devices are susceptible to electromagnetic interference sent by WF833F WF833 if inadequately shielded try to use the WF833F WF833 at least 20 cm away from TV sets radio and other automated office equipment so as to avoid electromagnetic interference e Operation of WF833F WF8
11. er supply 2 Spare rechargeable battery supply When using WF833F WF833 please connect it with the external power adapter Use the spare rechargeable battery in case of power failure or when there is no available power socket nearby When connected with external power supply WF833F WF833 will automatically check elec tricity quantity of the battery and charge the spare battery If the spare battery will be used up the indicator BAT will blink connect external power adapter to charge it 13 2 6 About UIM Card Ak 2 6 1 UIM Card Insert a valid UIM User Identity Module card into the terminal before usage Do not touch the metal surface of the UIM card in case that information in the card may be lost or damaged Keep the card away from electricity and magnetism Warning Power off the WF833F WF833 before removing the UIM card Inserting or removing the UIM card is prohibited when it is connected with the external power source 2 6 2 Usage of UIM Card e Power off WF833F WF833 disconnect from the external power outlet and open the rear cover of the UIM card e Slide the UIM card into the UIM slot Make sure that the beveled corner matches with the UIM slot Close the UIM card gate back to lock the UIM card Press the back cover to lock it into place Note If you cannot use WF833F WF833 normally after you insert the UIM card make sure the UIM card is inserted correctly or the UIM card is valid contact the network carrier Do not
12. individual Power failures surges fire flood accident actions of third parties or other events outside ZTE s reasonable control f Usage of products of third Parties or usage in conjunction with third party products provided that such defects is due to the combined usage g Any other cause beyond the range of normal usage for Products End User shall have no right to reject return or receive a refund for any Product from ZTE under the above mentioned situations e This warranty is end user s sole remedy and ZTE s sole liability for defective or noncon forming items and is in lieu of all other warranties expressed implied or statutory includ ing but not limited to the implied warranties of merchantability and fitness for a particular purpose unless otherwise required under the mandatory provisions of the law 1 5 Limitation of Liability ZTE shall not be liable for any loss of profits or indirect special incidental or consequential damages resulting from or arising out of or in connection with using of this product whether or not ZTE had been advised knew or should have known of the possibility of such damages including but not limited to lost profits interruption of business cost of capital cost of substi tute facilities or product or any downtime cost d e 2 1 Unpacking 2 Getting Started Parts Quantity Terminal 1 Ni MH battery 1 External power adapter 1 Antenn
13. m restart the WF833F WF833 22
14. t 20 6 Troubleshooting Fault Solution No dialing tone after off hook Check the installation of the antenna RSSI signal or restart WF833F WF833 The phone is buzzing after off hooking The phone is not compatible with WF833F WF833 change to another phone The phone alerts or gives other prompt sounds after off hooking D Make sure the UIM card is inserted correctly or it is valid contact the network carrier or whether the PIN code of UIM card is enabled The system stops sending dial tone 50 seconds after off hooking Hook on and then hook off again to make a call No caller number displayed Contact the network carrier about the CLIP mode of WF833F WF833 and the phone is matching Unusual power failure cause the terminal restart the FAX function can not work normally Read 4 G3 Fax and operate again 21 Fault Solution A succession of failure receiving or sending fax Maybe RF signal is weak or loosen antenna screw change the position of the terminal or check the an tenna installation It takes a longer time about 10 minutes before the charging May be the battery is completely flat in storage or used up It is normal phenomenon Other abnormal phenomenon Refer to the user manual and then check whether the parts such as power source and antenna are connected correctly If there is no proble
Download Pdf Manuals
Related Search