User Instructions
Contents
1. Memory spaces 50 Block formation of day of the week fixed free selection Switching status display yes Sealable yes2. amp e zs ia i cz z Te LARS zs E ca a c3 i P c5 B N x 7 amp o0 007 18 View edit program Info The program steps can be scrolled through a a with EDIT Po Poe The respective program can be edited by a pressing OK i5 ELI i 1 mm The procedure is the E JA same as when creating a new program G A 5 5 5 5 OFF DAJ OFF HOUR OFF run P e 18 08 900 isos c fu 5 ee oo amp 19 Delete individual programs Info When deleting individual programs the corres 5 ponding program steps DELETE SELECT Pot are deleted e g PO1 ON and P02 OFF i5 08 zn CONFIR Delete all programs DELETE ALL CONFIRM 20 Set date and time The date and time are preset at the factory Info F Ec ae co Em Iu Lu EZ E Lu E3 mm cJ e ru ca g t3 OO ON o0 00 Set AM PM 12 hour or 24 hour display H rs ze gn EE Inc Tu Pu F au fi I c a gj faz az c E oz 66 A o 26 Switchover for summer winter time m G3 G OO G9 21 Info The following settings are possible AUTO Factory presetting of the published calendar dates This is automati
3. with a preset time date and the menu language English After selecting language the time switch jumps automatically to Program mode after 4 seconds Res Menu ok Esc New weekly program WEEALY 16 Info The time switch has 50 memory spaces Example ON command at 3 pm OFF command at 6 pm Select NEW program and confirm with OK Select WEEKLY program and confirm with OK The free memory spaces are briefly displayed Select day block or individual day block formation as desired and confirm with OK Enter hour for ON command and confirm with OK Enter minute for ON command and confirm with OK Enter hour for OFF command and confirm with OK Enter minute for OFF command and confirm with OK Program is saved Program jumps to selection WEEKLY Now additional programs can be created 17 New holidays program 28 5 PEF SP ih d ers E g geal g ism 2 5l9 r amp 6 oe L 1 zd 3 CI S 5 N 3 52 o 7_ e Ze J u 5 us e w c9 fem zm t g m Lu Lt E Lo E3 i un rn A gt 2U 10 Lao c oe E a c c3 c3 Zz CJ 3 EZ or c ca a 3 r 5 CI u EET ae E CO amp co eee N e N 6 gt E o It m E oe jo a 2 A c
4. 5 Safety precautions The connection and installation of electrical devices may only be carried out by a qualified electrician Interventions in and changes to the device result in the voiding of the warranty claim Observe your national regulations and the respective safety provisions Fixed and flexible conductors of up to 2 5 mm may be attached to the external terminal clips Flexible cables with a cross section lt 1 mm should not be attached General information Deactivation commands take priority over activation commands If the power supply is correct the dots shown between the hours and minutes HH MM are displayed permanently The dots flash if the power supply is interrupted If there is no power supply the position indicator display goes out after 1 minute sleep function The whole display flashes the battery needs to be changed for up to 2 weeks to warn that v Installation on DIN rail Terminal diagram Ci D Battery change ER Attention XQ The battery change may only be carried out CE Type CR 2032 by a qualified electrician Isolate the device before replacing the x battery Check battery polarity when replacing j T ES A a FX EON Res Menu ok Esc Display A Channel status display Channel 1 ON Channel 1 OFF f communication lines for time display menu items entry prompts etc Day of week display
5. Display of summer winter time Holiday mode display Display of AM PM Operating voltage permanently lit dots Reserve power operation dots flash o Onm 14 General information The middle communication line shows the selectable menu item If confirmed with OK this item is activated Flashing texts or symbols require an entry If no entries are made within the next 2 minutes the clock reverts to Auto mode The time switch has a sleep function when not connected to power supply that keeps screen blank This function is activated after 2 minutes of no key board operations All settings saved will remain in the memory Buttons Scroll up in menu Press briefly 1 Press and hold approx 2 sec Scroll down in menu Press briefly 1 Press and hold approx 2 sec 5 f Manual operation in the automatic mode Res The programs are retained in the case of a reset The date and time must be set again Press reset button with a blunt object pen Exits the Automatic mode and enters the Programming mode Esc Press briefly one step back Press and hold approx 2 sec return to Automatic mode ok Make selection and apply Menu 15 Initial start up selection of menu language n Tur English Heb Deutsch j LANGUAGE ENGLISH ieri Espanol Italiano A e O Nederland Portugues Res Menu ok pe a In the delivered state the time switch is in the Auto mode
6. cally recalculated for each year NO No switchover 22 CALIBRAT Programming The start ra Co date of the summer time BRAT and winter time must be entered for this purpose The factory presetting is overwritten The programmed summer winter time is ca O automatically recalculated for each year The changeover takes place on the same specified day of the week in the same week of each month Example 03 21 Start summer time 10 31 Start winter time Attention Between the switchover it is not allowed to make set tings at the time switch Operating mode Info Res Menu Technical data Dimensions H x W x D Weight g approx Supply voltage Power consumption Switching capacity ohmic load VDE IEC inductive load cos q 0 6 Incandescent lamp load Switching output Switch contacts Ambient temperature 45 x 17 5 x 60 mm 90 see imprint on device 5VA 16 A 250 VAC 8 A 250 VAC 1 000W potential free 1 changeover contact 13 F to 131 F 25 C to 55 C FIX ON ou FIX FIX OFF ZA FIX 23 Press 1 x FIX ON continuous ON Press 2 x FIX OFF continuous OFF Press 3 x return to Auto mode AUTO no display programmed switching times Protection class ll Accuracy typ 2 5 s day at 68 F 20 C Reserve power 3 years from factory at 68 F 20 C Shortest switching time 1 min
Download Pdf Manuals
Related Search