23 December 2009
Contents
1. conversion RolandMutohMimaki Epson Conversion Guide available from support nutecdigital com e Please note In step 3 use the IPA to flush the system e Suck the Isopropyl Alcohol IPA from the printer with air using a either a syringe or the pumps Make sure the damper is also empty e Load the printer with NUtec MF Flushing Fluid and then purge the printer e Suck the NUtec MF Flushing Fluid from the printer with air using a either a syringe or the pumps Make sure the damper is also empty e Please note It is recommended as outlined in step 4 to remove the flush from the system by purging with air using a syringe or the service functions on the machine before introducing the Topaz T11 or Emerald E12 ink e Load the ink onto the machine gt As mentioned for further quidelines read the step by step guide on ink conversion RolandMutohMimaki Epson Conversion Guide available from support nutecdigital com For further enquiries please contact the NUtec Digital Technical team at support nutecdigital com DX456 new print head replacement procedure2. nUtec DIGITAL K a Release Date 25 July 2012 amp Bulletin Number TBN_024 From NUtec Digital Ink Technical Department To NUtec Digital Ink Distributors TOPAZ T11 amp Emerald E12 Ink Set DX4 5 6 new print head replacement procedure and ink load on new printer Dear customer NUtec Digital Ink recommends the following procedure when fitting a new Epson DX4 5 6 print head in or when loading a brand new Mutoh Mimaki or Roland machine with NUtec Topaz T11 amp Emerald E12 inks Please note When converting your machine already loaded with OEM or Aftermarket inks please refer to the following Technical note available from support nutecdigital com TBNO23 Topaz T11 Emerald E12 ink conversion principles Disclaimer This information is based on NUtec s present knowledge However this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship Under no circumstances will NUtec Digital Ink be responsible for any damage arising from improper flushing fluids used by the dealer or end user either directly or indirectly This includes but is not necessarily limited to damages arising from improper and inaccurate flushing procedures DX456 new print head replacement procedure nUtcc DIGITAL New print head replacement principles When unpacking a new print head please note the following gt Be careful not to touch the faceplate a
3. s this could damage the nozzles gt There are 2 recommended methods listed in order of preference by NUtec gt Method 1 using NUtec Conversion Flushing Fluid Fill a syringe with the Conversion Flushing Fluid and purge the print head Please note e tis recommended that the print head is purged through a damper The damper contains a filter which will trap any potential foreign contaminants and stop them from reaching the print head e Do not over pressure the syringe Applying too much pressure will damage the print head Purge the Conversion Flushing Fluid from the print head with air using a syringe Make sure the damper is also empty Follow the standard print head replacement procedure as prescribed in the User Manual of your digital printer Please note Do not delay too long as the print head might start drying gt Method 2 using Isopropyl Alcohol IPA Fill a syringe with the Isopropyl Alcohol IPA and purge the print head Please note e tis recommended that the print head is purged through a damper The damper contains a filter which will trap any potential foreign contaminants and stop them from reaching the print head e Do not over pressure the syringe Applying too much pressure will damage the print head Purge the Isopropyl Alcohol IPA from the print head with air using a syringe Make sure the damper is also empty Fill a syringe with the NUtec MF Flushing Fluid and then purge the print head Purge the NU
4. tec MF Flushing Fluid from the print head with air using a syringe Make sure the damper is also empty Follow the standard print head replacement procedure as prescribed in the User Manual of your digital printer Please note Do not delay too long as the print head might start drying DX456 new print head replacement procedure Utec GITAL INK D I Recommended configuration for purging print heads DX456 new print head replacement procedure nUtcc DIGITAL Loading ink in a brand new machine When loading NUtec Topaz T11 or Emerald E12 ink onto a brand new machine please note the following gt As a standard procedure the machine will require you to go through a charging procedure gt Atthe point of introducing the ink There are 2 recommended methods listed in order of preference by NUtec gt Method 1 using NUtec Conversion Flushing Fluid e Follow the conversion procedure as outlined in the step by step guide on ink conversion RolandMutohMimaki Epson Conversion available from support nutecdigital com e Please note In step 3 use the Conversion Flushing Fluid e Please note It is recommended as outlined in step 4 to remove the flush from the system by purging with air using a syringe or the service functions on the machine before introducing the Topaz T11 or Emerald E12 ink gt Method 2 using Isopropyl Alcohol IPA e Follow the conversion procedure as outlined in the step by step guide on ink
Download Pdf Manuals
Related Search