User Manual - Warehouse Sound Systems
Contents
1. System 10 Digital Wireless System Installation and Operation OPAR audio technica A ATW 1101 UniPak Transmitter System ATW 1101 G Guitar System ATW 1101 H Headworn Microphone System ATW 1101 H92 Miniature Headworn Microphone System ATW 1101 H92 TH Miniature beige Headworn Microphone System ATW 1101 L Lavalier Microphone System ATW 1102 Handheld Microphone System audio technica System 10 Installation and Operation CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN A A WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT REMOVE SCREWS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE CERTIFICATION THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES THIS DEVICE COMPLIES WITH INDUSTRY CANADA LICENSE EXEMPT RSS STANDARD S OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION Cet appareil est conforme a la aux norme s RSS exempte s de licence d Industrie Canada Son fonctionnement est soumis aux deux conditions suivantes 1 cet appareil ne doit pas causer d interf rence et 2 cet appareil doit accepter toutes les interf rences y compris celles susc2. 2 Carefully insert two fresh AA alkaline batteries observing polarity markings 3 Screw the body back together Do not overtighten Handheld Transmitter Battery Condition Indicator After the batteries are installed press and hold the Power Mute switch on the bottom of the handheld transmitter until the indicator LED turns green If the indicator LED does not light up when the Power Mute switch is pressed the batteries are installed incorrectly or they are dead The indicator LED will flash to show low battery condition Handheld Transmitter Mute Function With the transmitter on a slight touch of the power switch will toggle between muted and unmuted operation Red indicator LED shows muted operation Green indicator LED shows unmuted operation Handheld Transmitter Pairing Switch Used to complete pairing sequence See page 6 Handheld Transmitter Level Control Used to set microphone level See page 6 Handheld Transmitter Screwdriver Used to adjust Level Control See page 6 Level Control J g Pairing Switch udu LEVEL Battery Compartment Screwdriver LI J L i Okem piae SS j Ei SYSTEM Power Mute Switch Handheld Transmitter System ID Display Shows System ID See page 6 Note Syste
3. the mixer If the input of the mixer is an XLR type input connect a cable from the balanced XLR type audio output on the back panel to the mixer Power Connection Connect the DC plug on the included AC power adapter to the DC power input on the back of the receiver Secure the cord over the cord hook on the back of the receiver to keep the plug from being detached by an accidental tug on the cord Then plug the adapter into a standard 120 Volt 60 Hz AC power outlet Note that the receiver has no power Off On switch The receiver will be energized whenever the power adapter is connected and plugged into the AC outlet Unplug the power supply from the AC outlet when the system is not in use both for safety and to conserve energy Antennas Rotate the permanently attached antennas in the shape of a V both 45 from vertical for best reception ATW R1100 Receiver Controls and Functions Figure A Front Panel Controls and Functions 1 Antennas Position the antennas as shown 2 System ID Select Switch Press to cycle through System ID numbers System ID is an identical number assigned to a paired receiver and transmitter for identification purposes System ID Display Shows System ID number Pairing Switch Press to initiate pairing 5 AF Peak Indicator Only lights when audio distortion is present at maximum modulaton Not affected by position of Volume control 6 Pair Indicator Glows green to indicate prese
4. Pin 2 INST INPUT Open range environment with no interfering signals ONO Pin 3 MIC INPUT Pin 4 DC BIAS 9V Operating Temperature Range 0 C to 40 C 32 F to 104 F Batteries not included Two 15V BA z Battery performance may be reduced at very low temperatures Battery Life gt 7 hours alkaline Frequency Response 20 Hz to 20 kHz Depending on battery type and use pattern Depending on microphone type Dimensions 70 2 mm 2 76 W x 107 0 mm 4 21 H x Audio Sampling 24 bit 48 kHz RECEIVER Receiving System Diversity frequency time space 24 9 mm 0 98 D Net Weight without batteries 100 grams 3 5 oz HANDHELD TRANSMITTER Maximum Output Level XLR balanced 0 dBV RF Output Power 1Y MWy 1 4 6 3 mm unbalanced 6 dBV Spurious Emissions Following federal and national regulations Power Supply 100 240V AC 50 60 Hz to 12V DC 0 5A Batteries not included Two 1 5V AA center positive switched mode external Battery Life gt 7 hours alkaline power supply Depending on battery type and use pattern Dimensions 190 0 mm 7 48 W x 46 2 mm 1 82 H x Dimensions 254 8 mm 10 03 long 128 5 mm 5 06 D 50 0 mm 1 97 diameter Net Weight 290 grams 10 2 02 Net Weight without batteries 280 grams 9 9 oz Accessory Included Power supply Accessory Included AT8456a Quiet Flex stand clamp To reduce the environmental impact of a multi langu
5. age printed document product information is available online at www audio technica com in a selection of languages Afin de r duire l impact sur l environnement de l impression de plusieurs langues les informations concernant les produits sont disponibles sur le site www audio technica com dans une large s lection de langue www audio technica com Para reducir el impacto al medioambiente y reducir la producci n de documentos en varios eguajes informaci n de nuestros productos estan disponibles en nuestra pagina del Internet t In the interest of standards development A T U S offers full details on its test methods to other industry professionals on request Para reduzir o impacto ecol gico de um documento impresso de varias linguas a Audio Technica provid ncia as informa es dos seus produtos em diversas linguas na www audio technica com Per evitare l impatto ambientale che la stampa di questo documento determinerebbe le informazioni sui prodotti sono disponibili online in diverse lingue sul sito www audio technica com Der Umwelt zuliebe finden Sie die Produktinformationen in deutscher Sprache und weiteren Sprachen auf unserer Homepage www audio technica com Om de gevolgen van een gedrukte meertalige handleiding op het milieu te verkleinen is productinformatie in verschillende talen on line beschikbaar op www audio technica com ASLS ESD SSC SE gt REAR TESS SE BS OCPD il gt SAE TS BE www audio techn
6. ation purposes The System ID number is not related to transmitting frequency Due to the dynamic nature of System 10 automatic frequency selection the actual transmitting frequencies may change during power up or performance These frequency changes are seamless and imperceptible to the ear Single System Pairing System ID Instructions 1 Turn the receiver and transmitter on 2 Push the System ID button on your receiver to choose an ID number from 1 to 8 The receiver s display will show your new ID and begin to blink 3 Within 15 seconds push and hold the Pair button on your receiver for about one second The pair light will begin to blink green Your receiver is now in Pair Mode Note If the receiver pair button is not pushed within 15 seconds the system ID number will revert to its previous setting 4 Open your transmitter and push its Pair button within 30 seconds of entering Pair Mode The transmitter display will now show the System ID number you have chosen for your receiver The Pair Light will glow steady indicating you have successfully paired your system Multiple Systems Pairing System ID Instructions Note Up to eight systems may be used together without any frequency coordination problems or group selection issues 1 Turn the first receiver and first transmitter on 2 Push the System ID button on your first receiver to choose an ID number from 1 to 8 The receiver s display will show your new ID and begi
7. d Operation System Operation Turn down the receiver volume control and the mixer amplifier level before starting up the wireless system Do not switch on the transmitter yet Receiver on Plug the power supply into an AC power source The blue System ID number on the front panel will illuminate Transmitter on When the transmitter is switched on the receiver s green pair indicator will light and two indicators light on the transmitter the transmitter Power Battery Mute status indicator will glow green and the transmitter blue System ID display will illuminate The blue System ID display on the transmitter turns off after 30 seconds to conserve battery power the transmitter Power Battery Mute status indicator will remain illuminated indicating transmitter status To re illuminate System ID display press the Power Mute switch Note this will alter the transmitter mute status A slight touch of the power switch toggles between muted and unmuted operation The transmitter s Power Battery Mute status indicator glows red when transmitter is muted or green to indicated unmuted status In a low battery situation the Power Battery Mute status indicator begins to blink The transmitters have a soft touch power switch When the switch is set to Mute red indicator LED the transmitter produces RF with no audio signal When the switch is On green indicator LED the transmitter produces both RF an
8. d audio Excessive audio input to the transmitter will cause the receiver s red AF Peak indicator to light Transmitter Auto Power Off The transmitter will automatically power off after 10 minutes if 1 The receiver is powered off 2 No paired signal is established between the transmitter and receiver Receiver Volume Under typical operating conditions the receiver s volume control should be turned all the way up with overall system audio gain adjusted at the mixer or amplifier Input Level Adjustment Input trimmer controls in the transmitters enable you to maximize performance for a particular microphone or guitar sensitivity or to adjust for different acoustic input levels Adjusting Input Level UniPak Transmitter Slide the battery cover off the transmitter and remove the screwdriver from its clip Using the screwdriver gently turn the VOL Volume Microphone Instrument Level all the way up clockwise toward H Check for excessive gain by speaking singing into the microphone at typically loud levels while watching the receiver s Peak Indicator If the Peak indicator does light turn the VOL control slightly counterclockwise until the Peak indicator no longer lights with maximum audio input to the transmitter Adjusting Input Level Handheld Transmitter Unscrew the lower body cover and slide it off exposing the screwdriver and LEVEL Gain Trimmer control Fig C Remove the screwdriver from i
9. eptibles de provoquer un fonctionnement non souhait WARNING Changes or modifications not expressly approved in writing by Audio Technica may void the user s authority to operate this equipment RF Exposure Statement This transmitter must not be co located or operated in conjunction with any other antenna or transmitter This receiver must be positioned at least 20 cm away from any persons when in use Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experie
10. from the AC outlet when the system is not in use System Operating Frequencies Automatic Frequency Selection System 10 wireless systems operate in automatically selected frequen cies in the 2 4 GHz range far from TV and DTV interference Up to eight channels may be used together without any frequency coordination problems or group selection issues Every time a receiver transmitter pair is powered on it automatically selects clear frequencies Due to the dynamic nature of System 10 automatic frequency selection these transmitting frequencies may change during powerup or performance if interference is encountered These frequency changes occur at both the receiver and transmitter they are seamless and imperceptible to the ear System Frequencies Receiver Model ATW R1100 Transmitter Model ATW T100 1or2 For future reference please record your system information here the serial number appear on each transmitter and on the bottom of each receiver Serial Number Serial Number System 10 Installation and Operation Specifications OVERALL SYSTEM UNIPAK TRANSMITTER Operating Frequencies 2 4 GHz ISM band RF Output Power 10 mW Dynamic Range gt 109 dB A weighted typical Spurious Emissions Following federal and national regulations Total Harmonic Distortion lt 0 05 typical Input Connection Qn Fourpin Locking Connector Operating Range 30 m 100 typical a Pin 1 GND
11. ica com AY 7748 A ERER AT gas er SBE e AA TIEF MD MALE HAE SS SCH ENR Ae a ATE www audio technica comli 77 PA W E XEFE Tie Ta FO Ua o uly AMA JANEE AA SEAS ABAE IAIA Soeur AEA HL www audio technica com oA ete Mo AB So GLEE Poa F AeA audio technica Audio Technica Corporation audio technica com 2013 Audio Technica P52402 03
12. itter Input Connection Connect an audio input device microphone or guitar cable to the audio input connector on the top of the transmitter A number of Audio Technica professional microphones and cables are available separately pre terminated with a UniPak input connector see www audio technica com UniPak Transmitter Antenna The UniPak transmitter includes a permanently attached antenna If the received signal is marginal experiment with different transmitter positions on your body or instrument or try repositioning the receiver Do not attempt to remove replace or change the length of the transmitting antenna UniPak Transmitter Pairing Switch Used to complete pairing sequence See page 6 UniPak Transmitter Microphone Instrument Level Control Used to set microphone instrument level See page 6 UniPak Transmitter Screwdriver Used to adjust Level Control See page 6 UniPak Transmitter System ID Display Shows System ID See page 6 Note System ID is an identical number assigned to a paired receiver and transmitter for identification purposes When power is applied the System ID Display on the transmitter glows bright and then turns off to conserve battery life To turn the System ID Display back on mute and unmute the transmitter Figure E UniPak Transmitter Power Mute Button Input Connector JQ Antenna Indicator LED Power Mute Battery 6 System 10 Installation an
13. m ID is an identical number assigned to a paired receiver and transmitter for identification purposes When Power is applied the System ID Display on the transmitter glows bright and then turns off to conserve battery life To turn the System ID Display back on mute and unmute the transmitter 5 ee System 10 Installation and Operation audio technica Pairing Switch Screwdriver Dira poimaj o System ID Display Battery Compartment Figure D ATW T1001 UniPak Transmitter UniPak Transmitter Battery Installation 1 Slide off the battery cover 2 Carefully insert two fresh AA alkaline batteries observing polarity markings 3 Replace the battery cover Fig D UniPak Transmitter Power Mute Battery Indicator After the battery is installed press and hold the Power Mute button until the indicator LED turns green Fig E If the indicator LED does not light up when the power button is pressed the batteries are installed incorrectly or they are dead The indicator LED will flash to show low battery condition UniPak Transmitter Mute Function With the transmitter on a slight touch of the Power toggle between muted and unmuted operation Red muted operation Green indicator LED shows unmu ute button will indicator LED shows ed operation UniPak Transm
14. n to blink 3 Within 15 seconds push and hold the Pair button on your first receiver for about one second The pair light will begin to blink green Your first receiver is now in Pair Mode Note If the receiver pair button is not pushed within 15 seconds the system ID number will revert to its previous setting 7 System 10 Installation and Operation 4 Open your first transmitter and push its Pair button within 30 seconds of entering Pair Mode The first transmitter display will now show the System ID number you have chosen for your first receiver The Pair Light will glow steady indicating you have successfully paired your first system 5 Repeat for each additional system identifying each system with its own unique ID number Note While unique System ID numbers are not required we recommend assigning unique System ID numbers for each transmitter receiver pair As noted previously System ID numbers are not related to transmitter frequency they are provided for user convenience only f transmitter pair button is not pushed within 30 seconds the system will revert to its previous settings Ten Tips to Obtain the Best Results 1 Use only fresh alkaline or fully charged rechargeable batteries 2 Position the receiver so that it has the fewest possible obstructions between it and the normal location of the transmitter Line of sight is best 3 The transmitter and the receiver should be as close together as con ve
15. nce of paired transmitter Also blinks green to indicate pairing mode activated R Figure B Rear Panel Controls and Functions 1 AF Level Volume Control Adjusts audio output level of both AF Output jacks maximum output is fully clockwise 2 Unbalanced Audio Output Jack phone jack Can be connected to an unbalanced auxlevel input of a mixer guitar amp or tape recorder 3 Balanced Audio Output Jack XLRM type connector A standard 2 conductor shielded cable can be used to connect the receiver output to a balanced microphone level input on a mixer or integrated amplifier 4 Power Input Jack Connect the DC plug from the included in line AC adapter 5 Cord Hook Loop the cord around the cord hook to keep the DC plug from pulling out accidentally SYSTEM ID 4 MR System 10 Installation and Operation ATW T1002 Transmitter Setup Controls and Functions Battery Selection and Installation Two alkaline AA batteries are recommended When inserting the battery observe correct polarity as marked inside the battery compartment Power Battery Mute Status Indicator o Bg System ID Display Figure C ATW T1002 Handheld Transmitter Handheld Transmitter Battery Installation 1 While holding the upper part of the transmitter body just below the ball screen unscrew the lower body cover and slide it off to expose the battery compartment Fig C
16. nced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 Cet appareil numerique de la classe B est conforme a la norme NMB 003 du Canada CAUTION Electrical shock can result from removal of the receiver cover Refer servicing to qualified service personnel No userserviceable parts inside Do not expose to rain or moisture The circuits inside the receiver and transmitter have been precisely adjusted for optimum performance and compliance with federal regulations Do not attempt to open the receiver or transmitter To do so will void the warranty and may cause improper operation Notice to individuals with implanted cardiac pacemakers or AICD devices Any source of RF radio frequency energy may interfere with normal functioning of the implanted device All wireless microphones have low power transmitters less than 0 05 watts output which are unlikely to cause difficulty especially if they are at least a few inches away However since a body pack mic transmitter typically is placed against the body we suggest attaching it at the belt rather than in a shirt pocket where it may be immediately adjacent to the medical device Note also that any medical device disruption will cease when the RF transmitting source is turned off Please contact your physician or medical device provider if you have any questions or experience any problems with the use of this or any other RF equipment Impor
17. niently possible but not less than 6 2 m 4 While System 10 has been designed to stack for convenient multiple system operation please keep other wireless devices including wireless systems and routers away from System 10 receivers For best performance some routers and Wi Fi based wireless systems may need to be up to 30 feet away from System 10 receivers 5 The receiver antennas should be kept away from any metal 6 As some guitar pickups may be overly sensitive to magnetic interference please keep the System 10 UniPak body pack transmitter at least 1 foot away from guitar pickups 7 Use the transmitter level control to optimize performance for your instrument voice or other sound source 8 If the receiver output is set too low the overall signal to noise ratio of the system may be reduced Conversely if the volume control of the receiver is set too high it may overdrive the input of the mixer amplifier causing distortion Adjust the output level of the receiver so the highest sound pressure level going into the microphone or the loudest instrument playing level causes no input overload in the mixer and yet permits the mixer level controls to operate in their normal range not set too high or too low This provides the optimum signal to noise for the entire system 9 Turn the transmitter off when not in use Remove the battery if the transmitter is not to be used for a period of time 10 Unplug the receiver
18. rating in the 2 4 GHz range far from TV and DTV interference System 10 offers extremely easy operation and instantaneous channel selection Up to eight channels may be used together without any frequency coordination problems or group selection issues System 10 wireless ensures clear communications by providing three levels of diversity assurance frequency time and space Frequency Diversity sends the signal on two dynamically allocated frequencies for interference free communication Time Diversity sends the signal in multiple time slots to maximize immunity to multipath interference Finally Space Diversity uses two antennas on each transmitter and receiver to maximize signal integrity Each System 10 professional digital wireless system includes a receiver and either a body pack transmitter or a handheld microphone transmitter ATW 1101 UniPak body pack transmitter systems include models pre packaged with either an AT GcW guitar cable G a PRO 8HEcW headworn microphone H a PRO 92cW headworn microphone H92 a PRO 92cW TH headworn microphone H92 TH or an MT830cW lavalier mic L for particular applications All A T Wireless Essentials microphones and cables available separately are pre terminated for use with any ATW 1101 system 3 System 10 Installation and Operation Because System 10 packaging is designed to hold all versions of the system some compartments in the carton may be intentionally left emp
19. tant Safety Instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Unplug this apparatus during lightning storms or when unused for long periods of time 10 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as powersupply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped ONATARWN Thank you for choosing an Audio Technica professional wireless system You have joined thousands of other satisfied customers who have chosen our products because of their quality performance and reliability This wireless microphone system is the successful result of years of design and manufacturing experience Audio Technica s System 10 is an eight channel digital wireless system designed to provide rock solid performance along with easy setup and clear natural sound quality Featuring stackable contemporary styling System 10 is available in handheld headworn guitar lavalier and body pack configurations Ope
20. ts clip Gently turn the LEVEL control to its full clockwise position toward the side marked H the factory setting Check for excessive gain by speaking singing into the microphone at typically loud levels while watching the receiver s AF Peak indicator If the AF Peak indicator does light turn the LEVEL control slightly counterclockwise until the AF Peak indicator no longer lights with maximum audio input to the mic transmitter Return the screwdriver to its clip and close and secure the lower body No further transmitter gain adjustments should be needed as long as the acoustic input does not change significantly CAUTION The small trimmer controls are delicate use only the supplied screwdriver Do not force the trimmers beyond their normal 190 range of rotation Return the screwdriver to its storage clip when not in use Setting System ID Number amp Pairing your Transmitter and Receiver Your system has been preconfigured at the factory to operate with no other pairing setup required it will work out of the box That is your receiver and transmitter are already a digital pair and they have been assigned the same System ID number The pairing instructions outlined below will help you if you find it necessary to change system ID numbers in multiple system configurations or pair a new transmitter to an existing receiver NOTE System ID is an identical number assigned to a paired receiver and transmitter for identific
21. ty The ATW R1100 receiver includes a switching power supply that automatically adapts to changes in mains voltage The versatile ATW T1001 UniPak body pack transmitter has both a high impedance input for instruments and a low impedance input with bias connection for use with dynamic and electret condenser microphones The ATW T1002 handheld transmitter features a unidirectional dynamic microphone element Both the body pack and handheld transmitters use internal AA batteries and have Power Mute switches and input Trim level adjustments Receiver Installation Location For best operation the receiver should be at least 3 1 m above the ground and at least 3 1 m away from a wall or metal surface to minimize reflections Keep the receiver antennas away from noise sources such as other digital equipment microwave ovens as well as away from large metal objects Keep System 10 receiver 30 9 m away from wireless access points In multi channel systems position receivers at least 3 1 m apart and keep operating transmitters at least 6 2 m from the receivers to help assure maximum RF performance Output Connection There are two audio outputs on the back panel balanced XLR type output and unbalanced TRS phone jack Use shielded audio cable for the connection between the receiver and the mixer If the input of the mixer is a 14 jack connect a cable from the 14 unbalanced audio output on the back of the receiver housing to
Download Pdf Manuals
Related Search