sia3060 manual
Contents
1. max Dry contact relay output 1C COM N C N O Aarm Qut Reset Interruption time off relay approx 1 sec Temperature 25C 60 C Temper Output Dry contact Micro SW COM N C Adjustment of Optical Axis Horizontal 180 90 Vertical 20 10 Installation Outdoor Indoor wall or pole Dustproof Waterproof Rating IP65 Weight 468g Appearance 160 Unit mm D Co fo N English _10 SAMSUNG TECHWIN P Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase c2. the reflection part of the receiver in order for fine tuning after the initial optical axis adjustment 2 Make adjustment until the Good LED turns green 3 Remove the attenuation film and close the cover The attenuation film is a special film designed especially for blocking the external light from the transmitter by 90 and allowing inflow of only 10 English _8 Troubleshooting Problem Reason Action The power indicator of the 1 Power is not supplied 1 Apply the power transmitter does not turn 2 Loose connection or short circuited 2 Check if the cables are properly connected on Even if block the infrared 1 Power is not supplied 1 Tum on the sensor light the alarm indicator of 2 Loose connection or short circuited 2 Check if the cables are properly connected the receiver does not turn 3 The infrared light is incoming to the receiver 3 Remove the interruption object or change on after reflected by an object the installation site or the orientation of the 4 Two light sources are not properly blocked optical axis simultaneously 4 Block two light sources simultaneously The alarm indicator of the 1 The optical axis is dislocated 1 Adjust the optical axis as necessary receiver will not turn off 2 There exists an obstacle between 2 Remove the obstacle transmitter and receiver 8 Wipe out the impurities with a soft cloth 3 The cover of the transmitter or recei
3. Gecawelalee Sia 010610 BJ 016 016 B Important Safety Instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat reaisters stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus PNOarhto nN 11 Only use attachments accessories specified by the manufacturer A 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with P the apparatus When a cart is used Use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lighting storms or when unused for long periods of time a 14 Refer all serv
4. apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection Battery Batteries battery pack or batteries installed shall not be exposed to excessive heat such as sunshine fire or the like Disconnection Device Disconnect the main plug from the apparatus if it s defected And please call a repair man in your location English _2 When used outside of the U S it may be used HAR code with fittings of an approved agency is employed CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so Please read the following recommend safety precautions carefully e Do not Place th e Do not install on a surface where it is exposed to direct sunlight near heating equipment or heavy cold e Do not place thi area e Do not attempt e Do not place a glass of water on the product e Don e Don e Don User s iS apparatus on an uneven surface s apparatus near to service this apparatus yourself ot install near any magnetic sources ot block any ventilation openings ot place heavy items on the product Manual is a guidance book how to use the products The meaning of th e using sign in the book is following e Reference in case of providing information for helping o
5. eed up the response time turn it right to slow down the time m The factory default is set to 250 msec e Full speed run 50 msec e Fast walk 100 msec LA e Normal walk 250 msec e Slow walk 350 msec 50 msec e Jump over a fence or obstacle 500 msec Extending the radiation width according to the scanning range For extension of the radiation IR beam according to the scanning range of the transmitter or receiver please refer to the following table Model ie A A SIA 0030D 30m 0 9m SIA 0060D 60m 1 8m Protection distance L Transmitter Receiver English _7 Adjusting the optical axis 1 Connect both transmitter and receiver and turn them on 2 Look through the mirror of the sight and adjust the sensor so that the other sensor can be positioned in the center of the mirror m You can use the left right adjustable screw and the vertical adjustable screw of the reflector to refine your adjustment vertically 10 amp horizontally 90 3 Check the level of the light received from the monitor output signal You can use the tester to measure the DC voltage and refine your adjustment 4 Check the output voltage of the tester and close the cover Output Voltage Optical Axis Status 2 2V or higher Good 2 1V or lower To be adjusted Using the attenuation film for optimal adjustment of the optical axis 1 Attach the attenuation film to
6. f product s usages e Notice If there s any possibility to occur any damages for the goods and human caused by not following the instruction X Please read this manual for the safety before using of goods and keep it in the safe place English _3 IR Sensor at a Glance Cover Receiver Alarm LED Terminal Good LED Response Time Control Wheel Monitor Jack N J Sight Window Lens C x J Vertical Angle l Adjustable Screw ai What s Included Transmitter Temper KR Lf C Ga Channel Switch Power LED Y Bracket A N Brali ill y ome BA l E i Ww MENY i Injection Bracket Wing x4 N FL User Manual Warranty Card Steel Bracket x2 optional English _4 aN f ais i W B Screw x4 U shaped Bracket x2 optional Installation Instructions For best performance you should consider the followings when placing installing and keeping the product at a distance from the object e Do not expose it to a place where its light projector or light receiver is affected by a direct strong light such as sunlight or headlight below 2 is not allowed in the optical axis e Do not install it in an unstable not properly secured place wire fence or unsecured pole is not allowed Do not install it in a place where the infrared light is blocked due to a seasonal reason such as thick wood or bushes e Keep it away from the muddy
7. icing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped English _1 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PROCUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus CAUTION J RISK OF ELECTRIC SHOCK AY DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL EXPLANATION OF GRAPHICAL SYMBOLS alert the user to the presence of dangerous voltage within the product s enclosure that aX The lightning flash with arrowhead symbol within an equilateral triangle is intended to may be of sufficient magnitude to constitute a risk of electric shock to persons presence of important operating and maintenance servicing instructions in the literature JA The exclamation point within an equilateral triangle is intended to alert the user to the accompanying the product Class I construction An
8. ontract This product and its electronic accessories should not be mixed with other commercial wastes for disposal P No Z6806119301A 00
9. ver has impurities on it The alarm sounds 1 Disconnected cables 1 Check the connection status again intermittently 2 Fluctuation of the power voltage 2 Regulate the power voltage 3 There exists an obstacle between 3 Remove the obstacle transmitter and receiver 4 Change the wiring path 4 There exists a different strong power source 5 Secure the pole or support around the transmitter or receiver 6 Adjust the optical axis as necessary again 5 The transmitter or receiver gets loose and 7 Wipe out the impurities with a soft cloth unstable at its position 8 Set the response time longer ND The optical axis is dislocated The cover of the transmitter or receiver has impurities on it Sometimes a big bird or cat can block the light temporarily Wiring Diagram Receiver Transmitter 1 VCC DC12V 1 DC12V 2 GND 3 Normal Close 4 Common 5 Normal Open 2 GND 6 Tamper 7 Tamper English _9 Specifications amp Appearance Specifications Item Description Model SIA 0030D SIA 0060D Work Range Outdoor 30m Outdoor 60m Detection System NIR Blocking System Twin Beams IR Light IR LED Multi channel Digital CPU 4 CH Response Time 50 500 ms Power Voltage DC 12V 15 Alarm 0 5V or lower AGC Voltage Ready 2 0 2 2V Good 2 2V or higher Current Consumption Receiver 24mA Transmitter 12mA
10. water or sea water keeping splashing the infrared light is likely to be blocked by the muddy water or sea water Installation To mount on the wall 1 Loosen the screw to remove the cover of the sensor as shown 2 Insert the bracket wing on the side as shown 3 Attach the plate to the wall and mark the hole position then drill a hole and use the screws 4mm to fix the plate 4 Hook the upper hole of the sensor first and fit the lower hole into the wall bracket in the arrow direction English _5 5 Remove the slot shaped filling on the rubber hole of the sensor and pull out the cables through the hole Rubber Hole 6 When done adjust the optical axis and insert the cover To attach to the pole Pole bracket Optional 1 Pull out the cables from the wiring hole of the pole insert the U shaped pole bracket to the pole Cable In Hole 2 Attach the sensor to the bracket and arrange the cables as necessary Pole bracket m same as in wall mounting Optional 3 Put the cover as original m Pole external diameter 0388 046 English _6 Channel Settin To prevent misalarming due to possible frequency interference between two or more sensors in one place set the channel respectively lt 1 CH gt lt 2 CH gt lt 3 CH gt lt 4 CH gt Adjusting the response speed You can adjust the response time by tuming the response time control wheel left or right Turing it left will sp
Download Pdf Manuals
Related Search