Home
G2K Beambreak Sensor Manual
Contents
1. incorporates a self aligning infrared beam and a user controlled sensitivity with a radio frequency transmitter to activate your Guardian 2000 The result is an extremely reliable sensor designed to significantly reduce false activations Being able to bury the housings makes this an almost truly invisible sensor The flexible heads also make it extremely easy to deploy under almost any conditions Testing the Sensor Testing the sensor during deployment is crucial for suc cess Once the initial setup has been made test the sen sor before leaving the target area Conduct several walk through tests in the target area to determine if the speed is sufficient for the sensitivity set ting If not adjust the sensitivity accordingly Drop things such as pine cones sticks and similar objects through the beam to determine if it will set the sensor off If so adjust the sensitivity and conduct another test Emitter is on high power and facing north along the path instead of at a 90 degree angle to the path Emitter head is positioned about a foot from the ground Receiver is placed about 5 above the ground and looking down towards the emitter The sensitivity setting is 3 since the trail is a heavily wooded area and the target speed is anticipated slow Deployment of the Beam Break Sensor Always attempt to install the emitter and receiver heads facing north south direction within 35 feet of each other It is best deplo
2. RODUCTS PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT LIMITATION OF LIABILITY THE LIABILITY OF THE MANUFACTURER IF ANY AND PURCHASER S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE IN NO EVENT SHALL THE MANUFACTURER BE LIABLE TO PURCHASER FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER William Stump amp Associates LTD Guardian 2000 Beam Break Sensor User s Manual G2K Beam Break Sensor INTRODUCTION Congratulations and thank you for purchasing the Guardian 2000 Beam Break Sensor This sensor automatically integrates with your existing Guardian 2000 video system and is manufactured using stringent standards from customer input Features include e Weatherproof housings e Self aligning infrared beam e AA amp 9 Volt battery operation e Indoor and outdoor setting e User controlled sensitivity e 30 foot range As you read through this manual please keep in mind your system has been rigorously inspected for utmost quality assurance prior to shipment About the Beam Break Sensor The Beam Break Sensor
3. The limited warranty stated herein is subject to all of the following terms and conditions TERMS AND CONDITIONS 1 NOTIFICATION OF CLAIMS WARRANTY SERVICE If Purchaser believes that the product is defective in material or workmanship then written notice with an explanation of the claim shall be given promptly by Purchaser to the Manufacturer but all claims for warranty service must be made within the warranty period No repair or replacement of any product or part thereof shall extend the warranty period as to the entire product The specific warranty on the repaired part only shall be in effect for a period of ninety 90 days following the repair or replacement of that part or the remaining period of the product parts warranty whichever is greater 2 EXCLUSIVE REMEDY ACCEPTANCE Purchaser s exclusive remedy and the Manufacture s sole obligation is to supply all labor necessary to repair any product found to be defective within the warranty period Purchaser s failure to make a claim as provided in paragraph 1 above or continued use of the product shall constitute an unqualified acceptance of such product and a waiver by Purchaser of all claims thereto 3 EXCEPTIONS TO LIMITED WARRANTY The Manufacturer shall have no liability or obligation to Purchaser with respect to any product requiring service during the warranty period which is subjected to any of the following abuse improper use negligence accident modification failure of th
4. aline batteries into the emitter and four 4 new AA and one 1 9 Volt alkaline batteries into the receiver To turn power off simply remove one of the batteries from each pack Fig I Beam Break Emitter SENSTTVITY ADJUSIMENT 0 3 Sale Most Sensitive 3 Least Sensitive Fig 2 BeamBreak Receiver Operating the Beam Break Sensor 1 Obtain the hand held sensor alarm receiver provided with your Guardian 2000 and turn it on with the buzzer acti vated Set it close by so you can hear the buzzer Have the Guardian 2000 unit set up and ready to utilize 2 For indoor use slide the emitters high low switch to the low power DOWN position For outdoor use slide the emitters switch to the high power UP position See Figure 1 Position the emitter and receiver at least 10 feet apart especially if working indoors 3 Connect the three pin emitter head Smaller head with two LEDs to the emitter housing 4 Connect the four pin receiver head larger head with round opening in front to the receiver housing 5 Set the receiver sensitivity to an initial setting of O for maximum sensitivity See Figure 2 6 Place the receiver in the set up mode by sliding the setup arm switch to the UP position See Figure 2
5. e end user to follow the operating procedures outlined in the user s manual failure of the end user to follow the maintenance procedures in the service manual for the product attempted repair by non qualified personnel operation of the product outside of the published environmental and electrical parameters or if security seal has been defaced altered or removed The Manufacturer also excludes from warranty coverage products located outside the United States and consumable items such as fuses and batteries Items not manufactured by Backgrounds Unlimited Inc but included in system bought by Purchaser are limited to original manufacturer s warranty and will be repaired by Backgrounds Unlimited Inc on cost of material basis 4 PROOF OF PURCHASE The purchaser s dated invoice must be retained as evidence of the date of purchase and to establish warranty eligibility DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES THE MANUFACTURER HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY AND OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2 312 3 OF THE UNIFORM COMMERCIAL CODE AND OR ANY OTHER COMPARABLE STATE STATUE THE MANUFACTURER HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON MANUFACTURER S P
6. on The hand held sensor alarm receiver will not turn on at this point Arm the receiver by sliding the setup arm switch to the DOWN position The red LED will go out Break the beam by walking through or passing your hand in front of the receiver head The beam break will transmit a sig nal and the hand held sensor alarm receiver will buzz Now you are ready to test it with the Guardian 2000 Place your Guardian 2000 into the PGM mode Test the beam break again and the Guardian 2000 will wake and start recording Fig 3 Sample Table of Contents General Pre Operation Operation Testing Deployment Warranty Information General The Beam Break Sensor uses an infrared emitter and receiver to form an invisible beam When an object such as a person ani mal or vehicle breaks the beam a transmitter sends a signal to the Guardian 2000 record unit for activation A high setting for outdoor applications and a low setting for indoor use makes this sensor extremely versatile The weatherproof housings and flexi ble sensor heads enable quick and effortless installation Pre Operation 1 Read this manual thoroughly 2 Remove all screws from the lids of both the emitter and re ceiver The emitter See Figure 1 is the portion with the three pin connector and the receiver is the portion with the four pin connector and BNC antenna connector on the top lid See Figure 2 3 Insert 8 eight new AA alk
7. yed by placing the emitter head about one foot off the ground See Figure 3 Never place the receiver head looking directly at the sun It should be pointed directly towards the emitter head When using the beam break sensor to monitor a trail best results are achieved when placing the emitter and receiver heads about 45 degree angle on the trail This makes a target travel through the beam longer than a 90 degree angle setup See Figure 3 The beam break should be solidly mounted to avoid exces sive movement Therefore it is equipped with a small black clamp on each head to assist attaching to a solid ob ject Other devices such as wire ties zip ties hook and loop type fasteners and even natural vines can be used 10 11 Align the emitter head and the receiver head Check to see that the heads are aligned with at least a 10 degree deflection The emitter should be able to be transmitting red light illumi nated 5 10 degrees to the left and right of the center The red LED on the receiver head will light and remain lit as long as the emitter and receiver are aligned and unobstructed Should the red LED flicker on and off without being obstructed it is out of range and the two need to be moved closer to each other Conduct a test of the Beam Break by walking through it or plac ing your hand in front of the receiver The red LED will go out as soon as the beam is broken Once the beam is unob structed the red LED will turn back
Download Pdf Manuals
Related Search
Related Contents
Benchmark DLT1 DLT Tape Drive - C:\Users\todd\Documents\DLT1 Installation Guide Rhythm Notice d`utilisation ACR2 Basic Risk Assessment - Business Edition User Manual 4面 - 藤沢市 slides - FAFNER Concord Camera Eye-Q 3341z Digital Camera / Instrucciones para el Período de Inactividad de la Torre de Nokia 1661 User Guide Service Manual Copyright © All rights reserved.
Failed to retrieve file