Home

LS3200

1. Do not mount the controller and speaker on a ceiling Fixing the front speakers to prevent a falling accident When you mount the speaker to the wall make sure to set it firmly so that it cannot slip and fall This is especially important if you have small children Pass the end of the supplied wire through the hole of the stand and tie it Screw the eye bolt into the eye bolt hole on the back of the cabinet Eye bolt Eye bolt hole y Note A mounting screw s ability to support a speaker depends on the material and the position of studs of the wall We recommend that you consult a home installation professional Placing the Subwoofer E Using the rubber stoppers for a more stable platform We recommend to use the supplied rubber stoppers to achieve the best possible sound Attach the rubber stoppers to the four corners of the bottom The rubber stopper also provides stability 4 Thin rubber stoppers Bottom of the SKW B50 En 13 En 14 Connections Connecting the Front Speakers Connect the supplied front speaker Connect positive terminal of the front speaker to positive terminal of the controller LAP 302 and negative terminal of the front speaker to negative terminal of the controller Front left speaker Front right speaker Supplied speaker cable Tip The two speakers are identical so it doesn t matter which one you
2. Unplug the power cord from the wall outlet wait 10 seconds or more then plug it in again EThe controller turns off unexpectedly In the case of an analog connection 19 continuously feeding a weak input signal the Auto Standby function may be activated The controller will automatically enter standby mode when the Auto Standby function launches B The controller turns off and after restoring the power it turns off again The protection circuit may have been 14 activated Remove the power cord from the wall outlet immediately Make sure that all speaker cables and input sources are properly connected and leave the controller with its power cord disconnected for 1 hour After that reconnect the power cord and turn the power on If the controller turns off again unplug the power cord and contact your Onkyo dealer WARNING If smoke smell or abnormal noise is produced by the controller unplug the power cord from the wall outlet immediately and contact your Onkyo dealer BW There s no sound or it s very quiet B The remote controller doesn t work Make sure that all audio connecting 15 plugs are pushed in all the way Make sure that the input of TV is 15 connected properly Make sure that the polarity of the 14 speaker cables is correct and that the bare wires are in contact with the metal part of each speaker terminal Make sure that the speaker cables are 14 not shorting When the O
3. button on the remote controller for a while at least 10 seconds Try repeating this multiple times Remove the button battery wipe it with a dry cloth and then insert it again BW The controller and the TV operated by your TV remote controller doesn t work Make sure that the controller mounted 11 to the wall and the TV set are not placed too far Your TV remote controller might not be compatible with TV remote controller preprogrammed codes function If the ON STANDBY LED white does not flash by pressing the buttons on your TV remote controller use the supplied remote controller or program the controller If the controller cannot be operated with your remote controller even if the programming has been performed the controller might not recognize your remote controller In this case use the supplied remote controller En 23 En 24 MVolume or Muting function works by also pressing other buttons when operating controller with your TV remote controller For some TV remote controller 21 Volume or Muting function might work by also pressing other buttons Volume is increased by pressing 0 number button etc In order to prevent incorrect operation use the controller to configure volume control and muting buttons on the TV remote controller In addition disable TV remote controller operation Pairing the controller and the subwoofer Turn on the controller before performing a
4. when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions A When the power supply cord or plug is damaged B If liquid has been spilled or objects have fallen into the apparatus C Ifthe apparatus has been exposed to rain or water D Ifthe apparatus does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation E Ifthe apparatus has been dropped or damaged in any way and F When the apparatus exhibits a distinct change in performance this indicates a need for service 16 17 18 Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock The appa
5. 6 5 cm Full range Cone x 2 Studio Sound For DTS patents see http patents dts com Manufactured under license from DTS Licensing Limited DTS the Symbol amp DTS and the Symbol together are registered trademarks and DTS Studio Sound is a trademark of DTS Inc DTS Inc All Rights Reserved DOLBY DIGITAL Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories 3 Bluetooth Onkyo does not guarantee Bluetooth compatibility between the LAP 302 system and all Bluetooth enabled devices For compatibility between the LAP 302 system and another device with Bluetooth technology consult the device s documentation and dealer In some countries there may be restrictions on using Bluetooth devices Check with your local authorities The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by Onkyo is under license Other trademarks and trade names are those of their respective owners Please read rating label at the bottom or rear panel of system for other safety information E Using the Remote Controller Remove the plastic film before using the remote controller To use the remote controller point it at the controller s remote control sensor as shown below Placing on the floor etc LAP 302 Remote control sensor A AG e Remote control sensor App
6. SON STANDBY on the top panel for three seconds The function is switched on off and the ON STANDBY LED flashes amber When on Twice When off Once If you operate the controller with your TV remote controller set the Auto Power On function to on The controller cannot be turned on by using Power On button on your TV remote controller Note If you don t want the controller to be turned on automatically when the TV is on set the Auto Power On function to off About the Auto Standby function Since the Auto Standby function is set to on by default the controller will automatically enter standby mode if there is no audio input or operation performed for a specified length of time The length of time until the controller enters standby mode differs depending on the cables that are connected and the input source Optical digital audio cable or coaxial cable connections 2 hours 5 minutes if the TV is turned off Stereo mini plug cable connections 5 minutes Bluetooth 5 minutes To disable this function turn on the controller and then simultaneously press and hold ON STANDBY and the Q TV input buttons for three seconds When the function is set to off the ON STANDBY LED flashes white once Each time the procedure is repeated the function switches between on and off When the function is set to on the LED flashes twice Using the Sound Modes Selecting Sound Modes You can switch the sound mode
7. MUTING and INPUT DON STANDBY and SOUND MODE DON STANDBY and To prevent incorrect operation The unit is preprogrammed to support a large number of TV remote controllers For this reason using remote controllers other than that supplied with the unit and TV remote controllers may result in unexpected operation In order to prevent incorrect operation disable TV remote controller operation Note If you assign volume control and muting operations with the learning function the preprogrammed TV remote controller feature volume control and muting will be disabled In addition to cancel operations assigned with the learning function reset the controller gt page 22 En 21 En 22 Troubleshooting If you have any trouble using the controller look for a solution in this section If you can t resolve the issue yourself contact your Onkyo dealer If you can t resolve the issue yourself try resetting the controller before contacting your Onkyo dealer To reset the controller to its factory defaults simultaneously press and hold ON STANDBY and Volume buttons on the top panel for 10 seconds The controller will enter the standby mode after completing the initialization ON STANDBY Note that resetting the controller will delete your custom settings Power Wi Can t turn on the controller Make sure that the power cord is properly plugged into the wall outlet
8. instructions in the literature accompanying the appliance Important Safety Instructions Sy RR D d Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by 12 Use only with the cart the manufacturer PORTABLE CART WARNING stand tripod bracket or table specified by the manufacturer or sold e with the apparatus When a cart is used use caution ACY when moving the saasa cmi cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or
9. pairing 1 Press and hold LINK on the rear panel of the subwoofer for five seconds Flashing speed of the LINK LED is changed 2 Press and hold ON STANDBY on the controller for three seconds until the ON STANDBY LED flashes white The controller and the subwoofer starts pairing The ON STANDBY LED flashes white twice indicating that the pairing is completed Tip If the controller is turned off or enters the standby mode also the subwoofer enters the standby mode in 30 seconds In this mode the controller automatically detects a pairing point and reconnects The subwoofer is automatically turned on when the link is recovered Note Depending on the reception condition the sound might be stopped or interrupted while using This is not a malfunction In this case change the place or direction of the controller or the subwoofer If the controller and the subwoofer are too far the reception might be unstable They should be placed within 32 ft 10 m Ifthere is an obstacle metal door concrete wall and insulation contained aluminum foil etc between the controller and the subwoofer it might block the reception and stop the sound Place the controller and the subwoofer in good visibility with each other Use the controller and subwoofer included together in the package No other devices can be combined The controller contains a microcomputer for signal processing and control functions In very rare situat
10. voltages vary from country to country Make sure that the voltage in your area meets the voltage requirements printed on the unit s rear panel e g AC 230 V 50 Hz or AC 120 V 60 Hz The power cord plug is used to disconnect this unit from the AC power source Make sure that the plug is readily operable easily accessible at all times For models with POWER button or with both POWER and ON STANDBY buttons Pressing the POWER button to select OFF mode does not fully disconnect from the mains If you do not intend to use the unit for an extended period remove the power cord from the AC outlet For models with ON STANDBY button only Pressing the ON STANDBY button to select Standby mode does not fully disconnect from the mains If you do not intend to use the unit for an extended period remove the power cord from the AC outlet Nameplate Location The nameplate is located on the bottom exterior Preventing Hearing Loss Caution Excessive sound pressure from earphones and headphones can cause hearing loss Batteries and Heat Exposure Warning Batteries battery pack or batteries installed shall not be exposed to excessive heat as En sunshine fire or the like 3 7 Never Touch this Unit with Wet Hands Never handle this unit or its power cord while your hands are wet or damp If water or any other liquid gets inside this unit have it checked by your Onkyo dealer 8 Handling Notes Ifyou need to tran
11. 07458 U S A For Dealer Service Order and all other Business Inquiries Tel 201 785 2600 Fax 201 785 2650 http www us onkyo com For Product Support Team Only 1 800 229 1687 http www us onkyo com Europe Onkyo Europe Electronics GmbH Liegnitzerstrasse 6 82194 Groebenzell GERMANY Tel 49 8142 4401 0 Fax 49 8142 4208 213 http www eu onkyo com Onkyo Europe Electronics GmbH UK Branch Meridien House Ground floor 69 71 Clarendon Road Watford Hertfordshire WD17 1DS United Kingdom Tel 44 0 8712 00 19 96 Fax 44 0 8712 00 19 95 China Onkyo China Limited Hong Kong Unit 1033 10 F Star House No 3 Salisbury Road Tsim Sha Tsui Kowloon Hong Kong Tel 852 2429 3118 Fax 852 2428 9039 http www hk onkyo com Onkyo China PRC Mainland 302 Building 1 20 North Chaling Rd Xuhui District Shanghai China 200032 Tel 86 21 52131366 Fax 86 21 52130396 http www cn onkyo com Asia Oceania Middle East Africa Please contact an Onkyo distributor referring to Onkyo SUPPORT site http www intl onkyo com support The above mentioned information is subject to change without prior notice Visit the Onkyo web site for the latest update F1505 0 2940209 2 SN 29402092 C Copyright 2015 Onkyo Corporation Japan All rights reserved
12. 5 ft 1 5 m Front speakers SLM 302 Speaker stand x 2 Speaker cable 10 ft 3 0 m x 2 12 thin rubber stoppers For Front speakers and Subwoofer 8 thick rubber stoppers Wire cable with eye bolt x 2 Wireless subwoofer SKW B50 Power cord 2 page 16 Quick Guide 1 Australian models The plug type varies from country to country From the two supplied power cords choose the one whose plug matches the type of your AC wall outlet n catalogs and on packaging the letter at the end of the product name indicates the color Specifications and operations are the same regardless of color Features Sound System Controller Powerful Digital Amplifier 20 W Ch 4 Q 1 kHz 0 8 2 Channels Driven FTC 20 W Ch 4 Q 1 kHz 0 8 2 Channels Driven IEC 22 W Ch 4 Q 1 kHz 2 Channels Driven JEITA 2 Digital Inputs Optical Coaxial Analog Input Mini Jack Equipped with Dolby Digital Normal Mode for Wide Spread Surround Voice Mode for Clear Voice for News Program Bluetooth ver 2 1 EDR Enhanced Data Rate Auto Standby Function Auto Power On Function Preset Remote Control Codes for Most TV Brands and Programming Function Subwoofer Wireless Design for Free Setting and Powerful Sound Powered Bass Reflex Design 6 1 2 inch 16 cm Cone Front Speakers Detachable Speaker Stands for Greater Mounting Flexibility 2 1 2 inch
13. CbLIECTBEHUTE M34CKBaHMS M ApyrutenpunoKumu pasnopeg6n Ha QnpektnBa 1999 5 EC Onkyo Corporation t mto prohlaSuje Ze LAP 302 spl uje z kladn po adavky a v echna p slu n ustanoveni Sm rnice 1999 5 ES Undertegnede Onkyo Corporation erkl rer herved at f lgende udstyr LAP 302 overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF Hiermit erkl rt Onkyo Corporation dass sich das Ger t LAP 302 in Ubereinstimmung mit den grundlegenden Anforderungen und den brigen einschl gigen Bestimmungen der Richtlinie 1999 5 EG befindet K esolevaga kinnitab Onkyo Corporation seadme LAP 302 vastavust direktiivi 1999 5 EU p hin uetele ja nimetatud direktiivist tulenevatele teistele asjakohastele s tetele ME THN l IAPOY2A O KATAZKEYAZTHZ Onkyo Corporation AHAQNEI OTI LAP 302 ZYMMOPQOONETAI IPO2 TIX OYZIOAEIZ ATIAITHZEIZ KAI TIX AOITIEZ ZXETIKE2 AIATAZEIZ TH OAHMIA2Z 1999 5 EK Por la presente Onkyo Corporation declara que este LAP 302 cumple con los requisitos esenciales y otras exigencias relevantes de la Directiva 1999 5 EC Par la pr sente Onkyo Corporation d clare que l appareil LAP 302 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999 5 CE Con la presente Onkyo Corporation dichiara che questo LAP 302 conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE Ar o Onkyo Corporatio
14. N STANDBY LED flashes 18 white the muting is enabled Press i on the remote controller or the Volume buttons simultaneously on the controller to disable the muting Make sure that none of the connecting cables are bent twisted or damaged B The subwoofer produces no sound Make sure that there is no obstacle or reflection between the controller and the subwoofer Check that the LINK LED on the 24 subwoofer is lit If the LED is flashing pair the controller and subwoofer E Noise can be heard Using cable ties to bundle audio cables with power cords speaker cables and the like may degrade the audio performance so refrain from doing it An audio cable may be picking up interference Try repositioning your cables Make sure that the battery is correctly 8 installed with its polarity as indicated Make sure that the remote controlleris 8 not too far away from the controller and that there s no obstruction between the remote controller and the remote control sensor of the controller Make sure that the remote control sensor of the controller is not being subjected to bright light direct sunlight or inverter type fluorescent lights Ifthe remote controller doesn t work the first time it is used after the unit is purchased or if it is not used for a long period of time the battery may have become depleted Try the following operations Press and hold the VOLUME
15. ND MODE SUBWOOFER RC 858S ONKYO OON STANDBY Volume ON STANDBY LED Q TV input Bluetooth LED Turning On the controller 4 Press OON STANDBY on the top panel or Press D on the remote controller The controller comes on and the ON STANDBY LED lights white Press DON STANDBY or 5 again to set the controller to standby mode Tip For details on power management settings see Setting the Auto Power On 2 page 18 Note To prevent any loud surprises when you turn on the controller always turn down the volume before you turn it off Enjoying the sound E Operating with the remote controller 1 Turn on the connected TV 2 Press 1 INPUT to select the TV selector Listening to an audio from Bluetooth device 2 page 20 To adjust the volume use VOLUME Co Select a sound mode and enjoy Using the Sound Modes 2 page 19 E Operating on the controller 1 Turn on the connected TV 2 Press the Q TV input button repeatedly until the Bluetooth LED goes off to select the TV selector 3 To adjust the volume use the Volume buttons Tip Adjust the volume by 1 step in the 0 to 35 range The ON STANDBY LED flashes by receiving the signal from the remote controller When the Auto Power On function is set to on the controller is automatically turned on by receiving the audio input from the TV and the TV selector is selected Adjusti
16. ONKYO Living Speaker System 53200 Sound System Controller LAP 302 Front Speakers SLM 302 Wireless Subwoofer SKW B50 Instruction Manual Thank you for purchasing an Onkyo product Please read this manual thoroughly before making connections and plugging in your new Onkyo product Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new product Please retain this manual for future reference Contents Before Use 2 Connections 14 Operations Useful Function 21 AppendDG ener 22 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING AVIS RISK OF ELECTRIC SHOCK f RISQUE DE CHOC ELECTRIQUE DO NOT OPEN NE PAS OUVRIR he lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the AN presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing
17. Placement This section explains how to mount place the controller the front speaker and the subwoofer In this instruction manual Sound System Controller LAP 302 is described as 5 11 16 145 mm NS controller T oF Keyhole ye m slots for u e a wall i E mounting Bottom of the LAP 302 The controller can be mounted upside down Sound System Controller LAP 302 For mounting the controller Wall Front speakers SLM 302 use a screw with a head amp Subwoofer SKW B50 diameter of 1 4 6 mm or more and 2 32 7 mm or less qm Mountin h ntroller and a shank diameter of F 4 ount g the Controlle 1 8 3 mm or more and 3 16 to 1 4 5 32 4 mm or less The 5 to 6 mm screws as thick and long as possible are recommended Leave a gap of between 3 16 5 mm and 1 4 The controller can be placed on a flat surface and also mounted to the wall by using a commercially available wall mounting screw E Wall mou nting 6 mm between the wall and the base of the screw head as shown We recommend that you consult a d Mark the point of the wall by using e U apnd o NL n WALL MOUNTING TEMPLATE ount the controller as close as possible to the set without hiding the remote control sensor for the TV remote controller Mark the two points by using a pencil so Mount the controller in a well ventilated place that the controller can be mounted When using an appliance which uses 2 4 GHz horizon
18. e remote controller for three seconds with Bluetooth selector selected the Bluetooth connection to the Bluetooth enabled device is interrupted and start the pairing Note Ifthere is no sound output even after the paring is done successfully consult the user manual of the Bluetooth enabled device and then select the Onkyo LS3200 as the audio output device The controller can store the pairing information of up to 16 Bluetooth devices Ifthe pairing is done for the 17th Bluetooth device the pairing information of device connected via Bluetooth in the most past times is erased For some Bluetooth enabled devices a pairing is necessary for every reconnection The multiple Bluetooth devices cannot be connected at the same time Using a TV Remote Controller Preprogrammed feature The unit has been preprogrammed so that the unit can be operated using your TV remote controller Volume control and muting operations can be performed with this feature If you want to use other functions or cannot operate the unit with your TV remote controller you can use the learning function described below to enable these features To cancel this feature press and hold for approximately 3 seconds while continuing to press and hold DON STANDBY on this unit When this feature is enabled the ON STANDBY LED flashes white once When it is disabled the LED flashes twice Perform the same procedures to use the TV remote control
19. en you find the both audio output from your TV and LS3200 turn the audio output from your TV speaker off by setting on the TV En 15 Connecting the Power cord LAP 302 7 Connect the supplied AC adapter and the power cord 3 To AC wall outlet Insert the plug of the AC adapter into DC IN Plug the AC adapter into an AC wall outlet SKW B50 Connect the supplied power cord for subwoofer to AC INLET D0bUNDD000D000000000000000000 ot 0000000000 ox 9000000000 H 000000000 nooo Ml oooooooeoooo00v0oo00000 2 To AC wall outlet Note The shape ofthe AC INLET differs depending on the country 2 Plug the power cord into an AC wall outlet En 16 Note Before connecting the power cord connect all of your speakers and TV Turning on the unit may cause a momentary power surge that might interfere with other electrical equipment on the same circuit If this is a problem plug the unit into a different branch circuit Do not use the power cord other than the one supplied with the unit The supplied power cord is designed exclusively for use with the unit and should not be used with any other equipment Never disconnect the power cord from the unit while the other end is still plugged into a wall outlet Doing so may cause an electric shock Always disconnect the power cord from the wall outlet first and then the unit Operations VOLUME SOU
20. he surface cannot be seen and push it all the way in to strike the Tip The front speaker can be mounted placed both horizontally and vertically E Adjusting the angle The angle of the speaker can be adjusted in two ways depending on which stand slit you use Using the upper slit Using the lower slit Wall mounting Wall mounting 1 Attach the supplied stand referring to the illustration for wall mounting 2 Screw a commercially available wall mounting screw into the wall 3 Insert the head of the screw into the keyhole slot on the bottom of the supplied stand and fix it firmly Please confirm that the head of the screw is seated at the top of the hole Keyhole slot for wall mounting ua Before you wall mount the front speakers check the strength of the wall The supporting strength of the screws depends on the wall material and the position of the studs For mounting the front Wall speaker use a screw with a head diameter of 2 32 7 mm or more and 5 16 9 mm or zx less and a shank diameter of L L 1 8 3 mm or more and 5 32 to 3 16 5 32 4 mm or less The 4 to 5 mm screws as thick and long as possible are recommended Leave a gap of between 5 32 4 mm and 3 16 5 mm between the wall and the base of the screw head as shown Mount the front speaker to the vertical wall Mounting to the inclined wall might cause a falling of the speaker by coming off the stand
21. ions severe interference noise from an external source or static electricity may cause it to lockup In the unlikely event that this happens unplug the power cord from the wall outlet wait at least five seconds and then plug it back in Before disconnecting the power cord from the wall outlet set the controller to standby Specifications Controller LAP 302 Front Speaker SLM 302 Rated Output Power All channels North American 20 watts minimum continuous power per channel 4 ohm loads 2 channels driven at 1 kHz with a maximum total harmonic distortion of 0 8 FTC Others 2 ch x 20 W at 4 ohms 1 kHz 2 ch driven of 0 8 IEC Maximum Effective Output Power Australian 2 ch x 22 W at 4 ohms 1 kHz 2 ch driven JEITA THD N Total Harmonic Distortion Noise 0 8 Power Rated 0 2 1 kHz 1 W Damping Factor 29 1 kHz 8 Q Frequency Response 50 Hz 20 kHz 3 dB 3 dB DIGITAL Speaker Impedance 4Q 8Q Power Supply AC 100 240 V 50 60 Hz Power Consumption 17W Stand by Power Consumption 0 5 W Dimensions W x H x D 187 mm x 32 mm x 120 mm 7 3 8 x 1 1 4 x 4 3 4 Weight 0 3 kg 0 7 lbs E Audio Inputs Digital Optical 1 Coaxial 1 Analog Stereo Input 3 5 mm mini Bluetooth Version 2 1 EDR Profile A2DP GAVDP E Audio Output Speaker Output SPEAKER OUT Type Full Range Closed Box Impedance 4Q Maximum input power 20 W Output sound pressure level 86 dB W m F
22. ler again The mute state can be turned over each time you press the Mute button on your TV remote controller In such case you can synchronize the mute status of the unit and the TV by pressing and holding the Mute button on your TV remote controller Learning function The unit is set so that signals emitted from each button on your TV remote controller control specific operations It is recommended to select buttons that do not prevent TV operation when assigning the functions to your remote controller Signal of some types of remote controller may not be received by the unit E g To assign the unit s ON STANDBY function to the TV remote controller While continuing to press and hold the O TV input button on this unit press and hold DON STANDBY for approximately three seconds The ON STANDBY LED flashes amber for 10 seconds 2 While the ON STANDBY LED is flashing amber press any button on the TV remote controller three times while aiming it at the remote control sensor of the unit The ON STANDBY LED flashes amber twice to indicate that this was successfully configured After being configured pressing the button on the TV remote controller will operate the ON STANDBY function on the controller The learning function enables the following unit functions to be operated with your TV remote controller Press and hold the following buttons instead of ON STANDEY in step 1 VOLUME VOLUME
23. n deklare ka LAP 302 atbilst Direktivas 1999 5 EK b tiskajam prasibam un citiem ar to saist tajiem noteikumiem iuo Onkyo Corporation deklaruoja kad is LAP 302 atitinka esminius reikalavimus ir kitas 1999 5 EB Direktyvos nuostatas A Onkyo Corporation ezzennel kijelenti hogy a LAP 302 t pus beren dez s teljes ti az alapvet k vetelm nyeket s m s 1999 5 EK ir nyelvben meghat rozott vonatkoz rendelkez seket Hierbij verklaart Onkyo Corporation dat het toestel LAP 302 in overeenstemming is met de essenti le eisen en de andere relevante bepalin gen van richtlijn 1999 5 EG Niniejszym Onkyo Corporation deklaruje ze LAP 302 jest zgodny z zasadniczymi wymaganiami i innymi w a ciwymi postanowieniami Dyrektywy 1999 5 EC Eu Onkyo Corporation declaro que o LAP 302 cumpre os requisitos essenciais e outras provis es relevantes da Directiva 1999 5 EC Prin prezenta Onkyo Corporation declar c aparatul LAP 302 este n conformitate cu cerin ele esen iale si cu alte prevederi pertinente ale Directivei 1999 5 CE Onkyo Corporation t mto vyhlasuje e LAP 302 a spl a z kladn po iadavky a v etky pr slu n ustanovenia Smernice 1999 5 ES Onkyo Corporation izjavlja da je ta LAP 302 v skladu z bistvenimi zahtevami in drugimi relevantnimi dolo ili direktive 1999 5 ES Onkyo Corporation vakuuttaa t ten ett LAP 302 tyyppinen laite on direktiivin 1999 5 EY oleellisten vaatimusten ja sit koske
24. ng the Subwoofer Level 1 Press SUBWOOFER on the remote controller You can adjust the volume of subwoofer while listening to an input source Adjust the volume by 1 step in the 10 to 10 range The default is 0 Muting the controller You can temporarily mute the output of the controller Operating with the remote controller 1 Press 4 The output is muted and ON STANDBY LED flashes white E Operating on the controller Simultaneously press and hold the Volume buttons on the top panel Pressing Muting button on your TV remote controller sets both the controller and the TV to muting mode If you press and hold the Muting button on your TV remote controller for three seconds again the controller changes the setting This is the function that adjusts the controller s setting to the TV s setting by switching the controller s setting when the controller s setting and TV s setting of on off are different Tip To cancel the muting press X on the remote controller again or simultaneously press the Volume buttons on the top panel or change the volume level Muting is automatically cancelled when the controller is set to standby mode Setting the Auto Power On Since the Auto Power On function is set to on by default the controller will automatically turn on and the TV selector is selected when the controller receives the audio input from the TV 1 Turn off the controller 2 Press and hold
25. o select the Bluetooth selector The controller searches the component connected previous time and starts the pairing in five seconds when the corresponding item is not found Note If you press the Q TV input button on the top panel or Q INPUT on the remote controller again during pairing and switch the selector to TV the operation will be cancelled 2 While the Bluetooth LED is flashing quickly you can operate the Bluetooth enabled device to pair with the controller within a 32 ft 10 m range The pairing mode will be disabled in 25 seconds When the mode is disabled the LED will flash slowly For details on the Bluetooth connection refer to the user manual of the Bluetooth enabled device The controller may not work as normal depending on the circumstance even though the controller is placed within the 32 ft 10 m range In such cases get the Bluetooth enabled device closer to the controller and retry the operation 3 Once the controller is detected and its name Onkyo LS3200 appears on the display of your Bluetooth enabled device select the Onkyo LS3200 If a prompt requests a password PIN code key in the 0000 When a Bluetooth connection is established successfully the Bluetooth LED flashes twice then lights 4 Start playback on your device The controller automatically starts playing the audio Tip If you press and hold the Q TV input button on the top panel or Q INPUT on th
26. on t connect the power cord until you ve completed and double checked the TV connection Push plugs in all the way to make good connections loose connections can cause noise or malfunctions To prevent interference keep audio cable away from power cords and speaker cables Cables and Jacks BW Optical digital audio Optical digital connection allows you to enjoy digital sound such as PCM or Dolby Digital The audio quality is the same as coaxial w U OPTICAL E Coaxial digital audio Coaxial digital connection allows you to enjoy digital sound such as PCM or Dolby Digital The audio quality is the same as optical m COAXIAL E 1 8 3 5 mm Stereo mini plug This cable carries analog audio i ANALOG Note The controller s optical digital jack has a shutter type cover that open when an optical plug is inserted and close when it s removed Push the plug in all the way To prevent shutter damage hold the optical plug straight when inserting and removing Connecting to the TV TV gt Coaxial digital audio cable Stereo mini plug Optical digital cable audio cable supplied supplied Connect the TV to either of the jacks of the controller Tip If the Dolby Digital signal is input the ON STANDBY LED flashes white and amber alternately three times Note Don t connect the different types of jacks together Wh
27. only with the remote controller SOUND MODE button This button switches between the Normal Mode and Voice Mode The ON STANDBY LED flashes white once by selecting the Normal Mode When the mode is switched to the Voice Mode the ON STANDBY LED flashes white twice Sound Mode Normal Mode Description With this mode a dynamic 3D sound is delivered with a deep rich bass and high frequency clarity for crisp detail Voice Mode With this mode human voices are clearly produced This mode is optimum when listening to the news or documentary programs Tip The Sound Mode can be set by each of TV selector and Bluetooth selector separately Switching the audio of sound multiplex programs You can switch the audio only with Dolby Digital audio signals Press and hold the SOUND MODE button on the remote controller for three seconds Each time you press and hold the button the setting switches in the following order Primary audio The ON STANDBY LED flashes white once Secondary audio The ON STANDBY LED flashes white twice Primary audio secondary audio The ON STANDBY LED flashes white three times En 19 En 20 Listening to an audio from Bluetooth device Note If your mobile phone supports A2DP protocol its music will play through the controller 1 Press the TV input button on the top panel repeatedly or Q INPUT on the remote controller until the Bluetooth LED lights t
28. otherwise lower the unit s output level Use with a TV set In general Braun tubes used for color television sets etc are extremely sensitive and can be affected even by the magnetism of the earth If a speaker system is used near them therefore discoloring or distortion of pictures will occur These speakers are not provided with magnetic shielding If discoloration or distortion occurs move the speakers apart from the television set Input Signal Warning The speakers can handle the specified input power when used for normal music reproduction If any of the following signals are fed to them even if the input power is within the specified rating excessive current may flow in the speaker coils causing burning or wire breakage 1 Interstation noise from an untuned FM radio 2 Sound from fast forwarding a cassette tape 3 High pitched sounds generated by an oscillator electronic musical instrument and so on 4 Amplifier oscillation Special test tones from audio test CDs and so on 6 Thumps and clicks caused by connecting or disconnecting audio cables Always turn off your amplifier before connecting or disconnecting cables 7 Microphone feedback o Package Contents Make sure you have the following items Sound system controller LAP 302 Remote controller RC 858S AC adapter and Power cord 1 gt page 16 Stereo mini plug cable 5 ft 1 5 m Optical digital audio cable
29. r s faibles niveaux d nergie radiofr quence il est consid r conforme sans valuation de l exposition maximale admise EMA Il est cependant conseill de l installer et de l utiliser en maintenant la source de rayonnement radio lectrique 20 cm minimum du corps l exclusion des extr mit s du corps les mains les poignets les pieds et les chevilles FCC Caution FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connec
30. radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement For British models Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel IMPORTANT The wires in the mains lead are coloured in accordance with the following code Blue Neutral Brown Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red IMPORTANT The plug is fitted with an appropriate fuse If the fuse needs to be replaced the replacement fuse must approved by ASTA or BSI to BS1362 and have the same ampere rating as that indicated on the plug Check for the ASTA mark or the BSI mark on the body of the fuse If the power cord s plug is not suitable for your socket outlets cut it off and fit a suitable plug Fit a suitable fuse in the plug For European Models Hereby Onkyo Corporation declares that this LAP 302 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC C nuacrosujero Onkyo Corporation neknapupa 4e LAP 302 e B CboTBeTCTBMe CbC
31. ratus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus Don t put candles or other burning objects on top of this unit Batteries Always consider the environmental issues and follow local regulations when disposing of batteries If you install the apparatus in a built in installation such as a bookcase or rack ensure that there is adequate ventilation Leave 20 cm 8 of free space at the top and sides and 10 cm 4 at the rear The rear edge of the shelf or board above the apparatus shall be set 10 cm 4 away from the rear panel or wall creating a flue like gap for warm air to escape Precautions 1 Recording Copyright Unless it s for personal use only recording copyrighted material is illegal without the permission of the copyright holder AC Fuse The AC fuse inside the unit is not user serviceable If you cannot turn on the unit contact your Onkyo dealer Care Occasionally you should dust the unit all over with a soft cloth For stubborn stains use a soft cloth dampened with a weak solution of mild detergent and water Dry the unit immediately afterwards with a clean cloth Don t use abrasive cloths thinners alcohol or other chemical solvents because they may damage the finish or remove the panel lettering Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME READ THE FOLLOWING SECTION CAREFULLY AC outlet
32. requency Response 200 Hz 20 kHz Cabinet capacity 0 6 L 0 021 cubic feet Dimensions W x H x D 169 mm x 78 mm x 108 mm 6 5 8 x 4 3 8 x 5 1 4 incl grille and projection 0 7 kg 1 5 Ibs 6 5 cm 2 1 2 cone x 2 Spring type Non magnetic shielding Weight Drivers unit Terminal Other Subwoofer SKW B50 Rated Output Power FTC North American 50 watts minimum continuous power 4 ohms driven at 100 Hz with a maximum total harmonic distortion of 196 Rated Output Power IEC Others 50 watts minimum continuous power 4 ohms driven at 100 Hz with a maximum total harmonic distortion of 196 Play Frequency Band 40 Hz 200 Hz Cabinet capacity 11 5 L 0 41 cubic feet Dimensions W x H x D 261 mm x 337 mm x 269 mm 10 1 4 x 13 1 4 x 10 9 16 Weight 5 8 kg 12 8 Ibs Drivers unit 16 cm 6 1 2 cone Power Supply North American AC 120 V 60 Hz Others AC 220 240 V 50 60 Hz Power Consumption 15 W Non magnetic shielding Auto standby Other Specifications and features are subject to change without notice En 25 En 26 Memo Use this template to mount the LAP 302 to the wall gt page 11 uM L L b G W9 Syr B rm re O c c G m U gt m 27 ONKYO Onkyo Corporation Kitahama Chuo Bldg 2 2 22 Kitahama Chuo ku OSAKA 541 0041 JAPAN http Awww onkyo com The Americas Onkyo U S A Corporation 18 Park Way Upper Saddle River N J
33. rox 16ft 5m Remote control LAP 302 sensor Approx 16ft 5m E Replacing the Battery Use only a battery of the same type CR2025 Pull out firmly in the direction of the arrow pressing the tab in the direction of the arrow im di p SOF Pull e Back side Positive side Le 4 a Note If the remote controller doesn t work reliably try replacing the battery If you intend not to use the remote controller for a long time remove the battery to prevent damage from leakage or corrosion Remove expired battery as soon as possible to prevent damage from leakage or corrosion Replacing the battery incorrectly may cause an explosion Use only a battery ofthe same type or an equivalent Getting to Know the LS3200 C y ONKYO A LT LI For detailed information see the pages in parentheses D ON STANDBY button 17 Volume buttons 17 ON STANDBY LED 17 O TV input button 17 Remote control sensor 8 8 Bluetooth LED 17 Rear Panel LAP 302 DIST 228 SPEAKER OU AUDIO IN TV ae DC IN jack AUDIO IN TV DIGITAL OPTICAL and SPEAKER OUT terminals COAXIAL jacks AUDIO IN TV ANALOG audio jack See Connections for connection gt pages 14 to 16 Front Speakers SLM 302 Remote Controller Front grille Cabine
34. sport this unit use the original packaging to pack it how it was when you originally bought it Do not leave rubber or plastic items on this unit for a long time because they may leave marks on the case This unit s top and rear panels may get warm after prolonged use This is normal Ifyou do not use this unit for a long time it may not work properly the next time you turn it on so be sure to use it occasionally For U S models FCC IC Information for User IMPORTANT NOTE This equipment complies with FCC IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency RF Exposure Guidelines in Supplement C to OET65 and RSS 102 of the IC radio frequency RF Exposure rules This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation MPE But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person s body excluding extremities hands wrists feet and ankles REMARQUE IMPORTANTE Cet quipement est conforme aux limites FCC IC d exposition aux rayonnements d finies pour un environnement non r glement aux lignes directrices de la FCC en mati re d exposition aux radiofr quences RF sp cifi es dans le suppl ment C du bulletin OET65 et aux r gulations RSS 102 de VIC sur l exposition aux radiofr quences RF Cet quipement tant associ de t
35. t E N Front Side Slit for stand Speaker terminals ra Hole for eye bolt Rear The front grilles are not designed to be removed so do not attempt to remove them forcibly as this will damage them Subwoofer SKW B50 Front LINK LED 0000000000 0000000000 LINK button 5 AC INLET Li Note The shape of the AC INLET differs depending on the country En 10 RC 858S For detailed information see the pages in parentheses On Standby button 17 1 6 INPUT buttons 17 VOLUME buttons 17 SUBWOOFER buttons 18 X Mute button 18 SOUND MODE button 19 Using your TV remote controller TV remote control commands of several TV brands are registered in the controller These commands enable your TV remote controller to operate the Volume and Mute function of the controller Tip Some types of TV remote controllers are not compatible with this function In this case use the supplied remote controller or perform the programming of the controller See Using a TV Remote Controller for more details page 21 If you operate the controller with your TV remote controller set the Auto Power On function to on The controller cannot be turned on by using Power On button on your TV remote controller
36. t the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This transmitter must not be co located or operated in conjunction with any other antenna or transmitter Cet metteur ne doit pas tre plac de ou utilis conjointement avec une autre antenne ou un autre metteur For Canadian Models NOTE CAN ICES 3 B NMB 3 B For models having a power cord with a polarized plug CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT Mod le pour les Canadien REMARQUE CAN ICES 3 B NMB 3 B Sur les mod les dont la fiche est polaris e ATTENTION POUR VITER LES CHOCS LECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage
37. tally frequency range such as wireless LAN device microwave or digital cordless phone near the LAP 302 the controller may not be operated normally by noise or interruption caused by radio wave interference To avoid these issues place the 3 Insert the head of the screw into the controller away from other appliances keyhole slot on the bottom of the controller and fix it firmly Please confirm that the head of the screw is at the top of the hole page 27 2 Insert a commercially available wall mounting screw into the mark and screw it En 11 En 12 Mounting Placing the Front Speakers E Using the rubber stoppers for a more stable platform We recommend to use the supplied rubber stoppers to achieve the best possible sound Attach the rubber stoppers to the four corners of the bottom The rubber stopper also provides stability Placing on the floor etc Thick rubber stoppers Bottom of the SLM 302 Using the stand o R aee Thin rubber stoppers o T gt 4 of Bottom of the supplied stand N Border line E Attaching the stand Insert the stand into the stand slit on the rear of the front speaker To remove the stand pull the stand out of the speaker Table top Slit for stand a A Border line i wk pA Horizontal setting Vertical setting Wall mounting Horizontal setting Vertical setting Note Insert the stand until the border line of t
38. use on the left or right Speaker Connection Precautions Read the following before connecting your speakers You can connect speakers with an impedance of between 4 and 8 ohms Disconnect the power cord from the wall outlet before making any connections Pay close attention to speaker wiring polarity In other words connect positive terminals only to positive terminals and negative terminals only to negative terminals Incorrect connection may lead to unnatural sound being output due to issues such as reduced bass output due to phase reversal Be careful not to short the positive and negative wires Doing so may damage the controller e Make sure the metal core of the wire does not have contact with the controller s rear panel Doing so may damage the controller Don t connect more than one cable to each speaker terminal Doing so may damage the controller Don t connect one speaker to several terminals Using the Subwoofer A Corner L position 1 3 of wall position To find the best position for your subwoofer while playing a movie or some music with good bass experiment by placing your subwoofer at various positions within the room and choose the one that provides the most satisfying results About TV Connections Before making any TV connections read the manuals supplied with your TV D
39. vien direktiivin muiden ehtojen mukainen H rmed f rklarar Onkyo Corporation att denna LAP 302 f ljer de v sentliga kraven och andra relevanta stadgar i Direktiv 1999 5 EC H r me l sir Onkyo Corporation v yfir a varan LAP 302 er i samr mi vi grunnkr fur og a rar kr fur sem ger ar eru tilskipun 1999 5 EC Onkyo Corporation erkl rer herved at denne LAP 302 er i overensstemmelse med vesentlige krav og andre relevante bestemmelser i direktiv 1999 5 EC WEEE http www onkyo com manual weee weee pdf Speaker Precautions Placement The subwoofer cabinet is made out of wood and is therefore sensitive to extreme temperatures and humidity do not put it in locations subject to direct sunlight or in humid places such as near an air conditioner humidifier bathroom or kitchen Do not put water or other liquids close to the speakers If liquid is spilled over the speakers the drive units may be damaged Speakers should only be placed on sturdy flat surfaces that are free from vibration Putting them on uneven or unstable surfaces where they may fall and cause damage will affect the sound quality Subwoofer is designed to be used in the upright vertical position only Do not use it in the horizontal or tilted position If the unit is used near a turntable CD player or DVD player howling or slipping of sound may occur To prevent this move the unit away from the turntable CD player or DVD player

LS3200

Contents

Download Pdf Manuals

Related Search

Related Contents