Laser Tri260 SD FScan
Contents
1. INSTRUCTION MANUAL Laser Tri260 SD FScan 260mW DMX RGY animation laser with SD card interface M A N U AL V E R S O N 3 0 Fast scanning DMX RGY animation laser with SD card interface Includes FREE pre programmed SD card 10 channel DMX 512 operation via SD ram and standard DMX modes Compatible with Kam LC01 laser software for text and logo input 25kpps optical fast scanner creates amazing smooth animations Playback of ILDA laser show through computer interface amp SD card Pre programmed moving patterns in Auto mode Sound to Light Auto and DMX 512 modes Linkable Master Slave in Sound to Light mode Fan cooled and adjustable hanging bracket Key operated power control For the latest instruction manual updates and information on the entire Kam range visit www kam co uk Kam products are manufactured by Lamba plc Unit 1 Southfields Road Dunstable Bedfordshire United Kingdom LU6 3EJ Telephone 44 0 1582 690600 Fax 44 0 1582 690400 Email mail lambaplc com Web www lambaplc com If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal Due to continuous product development specifications and appearance are subject to change COPYRIGHT LAMBA plc 2009 E amp O E INTRODUCTION Thank you for purchasing the Kam Laser Tri260 SD Fscan To optimise the performance of this product please read these operating instructions carefully to familiarize yours2. gt Yellow No MMC SD card L Yellow Red File system FAT16 not found Yellow Yellow Red __ Data error when reading MMC SD card _ Yellow Yellow File not found or invalid file Yelow X NoDMx signal o Yellow _ Green Ready S O DMX channels assignment Channel1 Show select L This channel is used for show selection one of the first 16 shows including Pause can be selected Channel2 Show select H 16 banks of shows 16 shows each 256 shows can be selected using this function Channel3 Size projection size IMPORTANT WARNING When you change size by the use of DMX control a fader position of 0 minimum can cause a standing single point laser beam This can be a dangerous condition DMX only allows a refresh rate of 50 Hz Moving a control fader fast will result in jumps of the display settings Channel4 Offset X horizontal position A value of zero results in the maximum negative offset 128 is the center position and 255 is the maximum positive offset When changing this value via DMX the projected display can jump because DMX signal rate is slow Channel5 Offset Y vertical position See Offset X Channel6 Frame repeat Shows in ILDA format do not contain any timing information When all frames of a show are outputted one after the other the animation speed is too fast By repeating every frame a number of times the speed of the animation movement can b
3. Kam SD laser requires the SD card to be formatted in FAT 16 to allow files to be recognised FAT16 File Allocation Table is a filing system used in computer memory systems and storage cards Required for formatting SD card reader SD card and a PC Please follow the instructions below to format your SD card in FAT16 1 Insert the SD card into the card reader 2 Right click on the Windows Start button 3 Click once on the Explore option 4 Find the SD card in the Folders section of the window 5 Right click once on the SanDisk SD card icon 6 Click once on the Format option 7 Change the file system to FAT16 on the File system drop down menu If your file system options do not include FAT16 specifically use FAT or FAT Default Both are synonymous with FAT16 8 Adjust the Allocation unit size using the drop down menu if necessary The default FAT16 allocation unit size is 16 KB but you can change it up to 32 KB 9 Click once on the Start button on the Format window after making any desired changes Click once on the Yes button on the warning pop up window to start formatting the SanDisk card 10 Click once on the Close button on the Format window to complete the process SPECIFICATIONS Laser type Laser class Laser life Cooling Colour Laser output Scanner system Optical angle Control mode Power supply Power consumption Dimensions Net
4. mode For DMX mode the 10th dip switch must be ON Then set the DMX base address with the binary system 0 or 1 through switch 1 9 Examples DMX address __ DMX address eal AGGRDAB Me QSURWUSChle EE The device has 10 operating channels If you set the first unit as address 1 the next DMX device must start at address 20 DMX channels assignment enced ia 2 Blanking amp Blackout single colour auto R G Y Cycling slow to fast tri colour auto Cycling slow to fast tri colour move Cycling slow to fast bounded colour Cycling 124patterns 0 255 aena manual vertical move hous a Maa 0 127 manual vertical rotation 6 Vertical Roll 128 255 Ch1 must be 200 auto vertical rotation soeed up accordingly 255 7 Horizontal Roll 8 Rotation Steam on SD Card Controlling Mode The panel can be used to access some important parameters for the ILDA projector If the memory of the panel is empty it displays Err at power on At normal function if parameters are set correctly the panel displays the actual DMX base address for example 001 AND T p A T T E R N G R O U P There are 3 keys from left to right 1 FUNC By pressing FUNC the actual parameter for changing is selected There are 3 parameters currently available Adr DMX base address Int max Intensity for colour and intensity output laser Ort orientation of the projection 2 SE
5. If trying to set a value beyond the limits the panel automatically corrects to an allowed value during input Intensity The value under Int sets the maximum intensity for the laser All show values for RGB outputs and analog intensity will be divided by this value linear For the projector this value should be set to 99 Orientation There are 8 different values possible allowing all possible projection orientations This is important for back projections or if it is not clear how the projector is installed at the location normal X invert Y invert X and Y invert X and Y changed X and Y changed and X invert X and Y changed and Y invert X and Y changed and both inverted NOOA WD O Message center lf any error condition occurs a code will be displayed on the status LEDs see table Not all errors will cause the stop of playback Errors from the memory card read write will cause a total shutdown of the unit lf there is no card or the card is not inserted correctly of if the incorrect format or file system the unit functions will be shut down When there is no file allocated to a selected show number this is no error condition and the unit will switch the output to Pause Shown number 0 PAUSE When the accessed show file is not valid or corrupted the playback will be switched off All other functions keep running and the selection of another show is possible Ready DMX Data Error gt Z
6. L After selecting the parameter with FUNC press SEL and the current stored value will be displayed By pressing SEL again the digit for changing will blink Pressing Select multiple times will activate all digits by flashing one after the other 3 Up Use this key to change the current number in the blinking digit The number will be increased When reaching the maximum number 9 the number will be start from zero again Example set DMX base address to 200 Press FUNC until Adr blinks Press SEL until current value is displayed and right digit blinks Press Up until O is reached Press SEL to go to middle digit Press Up until 0 Press SEL until left digit blinks Press Up until 2 is reached Press FUNC to exit this parameter The value is stored automatically All values are stored and activated when you exit the parameter input by pressing FUNC parameter The value is stored automatically Without changing anything in the parameter input routine the panel will return to main routine after about 10 seconds without storing value to memory Note that playback of longer shows may be interrupted stopped when changing parameters at the panel during show output Display of single frames of short sequences normally will not be interrupted Limits DMX base address 1 512 Intensity 0 99 Orientation 0 7 Limits will be controlled automatically by the panel
7. Weight Green Laser Diode Pumped Solid Stated Laser DPSSL Red Laser Semiconductor Diode Laser Class IV gt 5000 Hours forced fan Air cooled Red 140mw 650nm Green 120mw 532nm 260mW Red 140mw 650nm Green 120mw 532nm 25Kpps 20 Sound active Auto mode DMX512 compatible 10channels Playback of ILDA laser show files in SD card channels ILDA 25 pin Interface for PC controller AC 110 240V 50 60Hz lt 300W W200mm xH260 mm xD310 mm 5 5 Kg
8. e controlled Values by DMX control are 1 to 16 Memory card Compact Flash card All Compact Flash cards up to a maximum capacity of 3 Gigabytes can be used Important The card has to be formatted with FAT16 file system only The manufacturer recommends the use of high quality cards Unbranded cards can cause read errors All cards shipped together with the equipment are formatted correctly and must NOT be reformatted Caution When using own cards or reformatted cards by using a PC with Windows operating system it is not ensured that the cards are formatted FAT16 Depending on the memory size of the card Windows can format these to FAT12 FAT16 or FAT32 file system The Poseidon will not work with other file systems than FAT16 Avoid formatting the card by the use of a PC with Windows operating system No subdirectories are supported by the unit All show files and configuration files must be placed in the root directory of the card There must not be more than 260 files located in the root directory It is recommended not to store more files than necessary on the card Only short filenames will be processed 8 3 format by the unit The unit does not support long filenames The name of the files should be not longer than 8 characters plus the extension for example ILD When copying files to the card both long and short filenames are created The unit only reads the short names The long names need additional space in t
9. elf with the basic operations of this unit The KAM Laser Tri260 SD Fscan laser has been designed to create amazing laser effects Please keep these user instructions in a safe place for future reference This unit has been tested at the factory before being shipped to you There is no assembly required WARNING To prevent or reduce the risk of electrical shock or fire do not expose this unit to high temperature rain or moisture Unintended reflections of the laser beam from reflective or metallic surfaces can be dangerous Do not touch the laser aperture When cleaning the laser Aperture please use a soft cloth Never remove warning or informative labels from the equipment Do not connect this equipment to a dimmer pack Laser Class 3B product National regulations must be adhered to at all steps of installation These can be downloaded from the website www kam co uk In Germany apply DIN 56912 and BGVR LASER note additional regulations may apply Always replace the fuse with exact same type because anything other than the specified fuse can cause a fire electric shock damage your unit and will void your manufactures warranty This appliance must be earthed This appliance should be used by qualified personnel only UNPACKING YOUR NEW KAM PRODUCT Carefully inspect your laser as you unpack it If any damage is evident please notify the supplier you purchased the unit from immediately For safety reasons do not use the unit if an
10. he root directory To avoid losing space and limiting maximum possible number of files the names should be kept as short as possible Short filenames are not case sensitive WE RECOMMEND USING THE KAM LCO1 LASER SOFTWARE See www kam co uk Reserved Filenames Some filenames are reserved for device control These files will be read out by the unit automatically and must NOT be deleted or renamed The following filenames are reserved CONFIG DAT Contains output settings for the unit FLASHMP BIN Controls program for firmware update FWUP12C BIN File for a specific firmware update When this file is found the unit automatically updates the firmware After this procedure this file will be deleted automatically by the unit PC MODE Put the mode switch to PC MODE position and then connect the PC ILDA output interface to the ILDA IN connector on the rear panel using a standard and easily available not supplied ILDA connecting cable If you want to make your own cable you should comply with the below signal definition table of ILDA DB 25F pin outs Greens 6 OVto25V ae Red 18 Connect to ground _ Caution Because the device is equipped with scanner of 20Kpps so you should do tune down the setting of scan rate below 20K per second when you use software Pangolin Mamba Phoenix etc to control the device Too high a scan rate will be greatly harmful to the scanner motor IMPORTANT INFO REGARDING SD CARDS Your
11. y damage has occurred during transportation Contents SD260 tri colour laser projector 1pc Power cable 1pc DMX signal cable 1pc User manual 1pc SD card 1pc REAR PANEL MODE SWITCHES fe N i j Caan j J VW ae J SS OUND amp DMXE SD CARD PC MODE 5 READY DMX ie ce Co E DMX OUT ERROR DATA C OFF LOCO ba j i r TISS C ON ACIN ss mmBN YS IS i 3 vw 4 K i ILDAIN ILDA THRU _ a ee AT LASER TECHNOLOGY o FUNCTION TABLE Audio in 6 Mode Switches Select the operating modes __ _ o 8 DMXOUT DMX 512 signal output SSS 9 _ Dip Switches si Setting the DMX start address __ ooo OPERATING INSTRUCTIONS MODE SWITCHES l 2 3 Sound amp DMX Control mode You can choose Sound or DMX control mode through dipswitch 10 When all dipswitches are set to the OFF position the unit works in sound mode When dipswitch 1 is set to the ON position the unit works in auto mode To set unit to slave set dipswitch 2 to the on position Function mode setting Function Dip Switches 2ound mode DMX mode function switch iiid ii For DMX switch 10 must be on slave mode Master Slave settings No DMX Controller For master slave mode put the 2nd switch to ON position and it works as slave lt se SLAVE WN Sound mode Dje Auto mode DMX Control
Download Pdf Manuals
Related Search