GM-14915045 Rev 2 DL
Contents
1. 2 Inthe Com Parameters dialog box select the PC serial port the DL 4plus is connected to from the Com Port drop down list and 57600 from the Baud Rate list and then select OK Com Port r Baud Rate 57600 Cancel 3 Select the UpLoad button rams Dow 4 Inthe UpLoad dialog box select the Connect button to establish communications with the DL 4plus m 5 Select the group to upload to the DL 4plus from the list of groups on the PC Y UpLoad UpLoad From PC Groups M d 6 Select the UpLoad button to copy the group errs ero UpLoad 7 Press the Disconnect button and close the UpLoad dialog Repeat these steps to upload more log groups Up to 5 log groups can be stored in the DL 4pl us at any one time LOGGING THE DATA After the log group has been uploaded the DL 4p us can be set to begin logging data by using the LCD screen and controls on the front face of the unit 1 Press the 9 button three times to navigate to the CONFIG LOGGING menu on the LCD screen CFGLOG _ HOME LOGGING CONFIG LOGGING SV 10 DGPS DoP25 Y gt 2 Press the amp button and then the button to move to the following screen PICK PICK SCHEDULE Sv 10 DGPS DOP 2 5 EEE 3 Press the amp button until the name of the log group you would like the DL 4plus to log is shown PICK PICK LOGGROUP1 5v0 DGPS nor 2s MN LOGGING 4 Press the D2. LOGGROUP1 from the Group Name drop down list and if desired use the Rename button to rename the group Group Name LOGGROUPT Rename CHR_BASE z Logs Post RTCM_1819 DGPS BASE LOGGROUPI OGEROUP l LOGGROUP3 LOGGROUP4 LOGGROUPS Log Name ET Descriptio 4 Select the Add button to add a log to the group Oe Edit 5 Select the log to add from the Log Name drop down list 6 Select the Disk radio button to log to the internal CompactFlash Select the log format using the Format radio buttons Select the trigger for the log using the Trigger radio buttons If the On Time trigger is selected select the period for logging using the Period scroll bar 9 Select OK to add the new log to the log group Group POWERUP Add Log O x Description Log Name PSRPOS PSR Position Log to Format Trigger f Com 1 Binary f On Time CO On Hew C Com f Ascil On Changed On Next i File C Raw C Once C On Mark On Time Details Period r fio Seconds Cancel 10 Repeat steps 4 through 9 to add more logs to the group 11 Select OK in the Group Editor dialog box to save the changes to the group d JANY Cancel OF UPLOADING A LOG GROUP Once a log group has been created it can be uploaded to the DL 4p us The steps below provide information on uploading a group 1 Select the Comm Params button from the main DL4 Tool window
3. Atel Customer Service using one of methods provided below Email support novatel ca Web www novatel com Phone 1 800 NOVATEL U S amp Canada 403 295 4900 International Fax 403 295 4901 Noite GM 14915045 Rev 2 2004 08 30
4. CTFLASH CARD 3 You may get a DISK ERROR message on the LCD screen of the DL 4plus If so enter the following using GPSolution DISK FORMAT Wait a few minutes until the error message is gone Use the DL 4plus power button to turn it off and then on again When power is returned the DL 4p us should be able to use the flash card INSTALLING THE PC UTILITIES Once the DL 4plus is connected to the PC antenna and power supply install NovAtel s GPS PC utilities Start up the PC Insert the accompanying CD in the CD ROM drive of the computer Install the PC utilities by advancing through the steps provided in the NovAtel GPS PC Utilities setup utility If the setup utility is not automatically accessible when the CD is inserted select Run from the Start menu and select the Browse button to locate Setup exe on the CD drive CREATING A LOG GROUP USING DL4TOOL Log groups are sets of logs to be captured by the DL 4plus A group can be created in DL4 Tool and then downloaded to the DL 4plus 1 Launch DL4 Tool from the Start menu folder specified during the installation process The default location is Start Programs OEM4 PC Software Select the Group Editor button File Help Group Editor Schedule E Within the Group Editor pre defined log groups are provided for use during common operational modes In addition five empty log groups are provided Both the pre defined and empty log groups are editable Select
5. DL 4p us QUICK START GUIDE This guide provides the basic information you need to setup and begin using your new DL 4plus For more detailed information on the installation and operation of your receiver please refer to the user manuals provided on the accompanying CD To order a printed copy of the manuals free Manuals card The DL 4plus with 2 200 firmware or higher provides a USB 2 connection through its COM1 port The USB drivers along with installation instructions are available in the USB Drivers directory of the CD provided BOX CONTENTS In addition to this Quick Start Guide the following is provided with your DL 4plus e 1 CompactFlash card e 112V power cable 1 I O cable 1 USB cable 1 null 3 modem cable 1 straight through serial cable e 1 CD containing e An installation program for NovAtel s GPS PC utilities including GPSolution and DL4Too e Product documentation including user manuals e The OEM4 Software Development kit e DL 4plus LCD Menus Quick Look e OEM4 Family Quick Reference Guide e User Manuals card for requesting printed manuals ADDITIONAL EQUIPMENT REQUIRED The additional equipment in this list is needed for a basic setup e A Windows based PC with an RS 232 DB 9 port e A quality GPS antenna like NovAtel s GPS 702 e An antenna RF cable with a TNC male connector at the receiver end such as NovAtel s C016 model e One of the following e Astanda
6. button to select the log group 5 Press the amp button and then the button to move to the screen shown below EXECUTE APPLY NO svi0 DGPS DOP2 5 PEL 6 Press the amp button until the YES option is selected EXECUTE APPLY YES LOGGING 5v0 DGPS DOP 2 5 PEL 7 Press the button to begin logging of the selected group 8 Press the button to return to the main menu Your data logs are now being recorded to the internal flash card STOPPING LOGGING To stop logging first navigate to the CONFIG LOGGING menu and select the name of the group in the PICK screen Then select NO in the APPLY screen to stop logging of that group CFG SITE EXECUTE LOGGING APPLY NO 5v0 DGPS 00P25 M See the DL 4plus User Manual for information on how to retrieve the data once logging is stopped GPSOLUTION Along with your DL 4plus GPSolution is included to provide a graphical display of key information about your receiver and its position For more information about using GPSolution with your receiver please review the documentation provided on the enclosed CD DETERMINING WHEN THE POSITION IS VALID When the receiver has a valid position the Position Mode area in the lower left corner of the screen to the right of the satellite count displays the current position mode rather than NONE QUESTIONS OR COMMENTS If you have any questions or comments regarding your DL 4plus please contact Nov
7. rd 12 VDC automobile power outlet or a 7 18 VDC power supply capable of at least 4 0 W and a power cable with a 4 pin LEMO plug LEMO part number FGG 0B 304 CLAD52Z at the receiver end SETTING UP YOUR DL 4plus Complete the steps below to connect and power your DL 4plus of charge follow the instructions given on the enclosed User 1 Mount the GPS antenna on a secure stable structure with an unobstructed view of the sky Insert the provided CompactFlash card into the slot provided behind the door on the front face of the DL 4p us Open the door by loosening the screw at the right end Using the antenna RF cable connect the GPS antenna to the GPS port which is found on the DL 4plus back face 1 If an alternative power source is preferred the automobile power adapter can be cut off from the power cable The exposed wires red and orange for positive brown and black for negative can then be tied to a 7 18 VDC supply capable of at least 4 0 W The use of a3 A slow blow fuse is recommended 4 Connect the COM1 port on the receiver to a serial port on the PC using the provided serial or USB cable gt red mark on the receiver connector with the red mark on the cable connector 2 6 Plug in a user supplied adapter and or connect and turn on the power supply When the DL 4plus is properly powered the PWR LED is red 7 Press the button on the front face of the DL 4plus COMPA
Download Pdf Manuals
Related Search