GSM Relay user manual
Contents
1. Assign a user defined name for Input 1 SMS returned Input name saved Assign a user defined name for Input 2 SMS returned Input name saved for input 2 max 10 Characters If name is less than 10 characters fill with spaces Erase delete the user names for Input 1 and Input2 and default back to INPUT1 and returns a sms Input names INPUT2 in reply SMS deleted IputAutoReplyJumperJ9 Jumper in Automatically replies with a SMS if any one of the 2 Inputs changes state indicating the state of the inputs and voltage Deletes the user assigned names for both inputs and GSM Relay INPUTS The 2 Inputs is potential free inputs no voltages should be injected here The user must ensure potential free contacts on inputs eg Relay contact or switch or jumper The board source a negative supply for the input board marked NEG IP1 NEG IP2 As soon as the unit is powered up it takes a sample of the input status contact between NEG and IP1 and NEG and IP2 and saves this as the normal state If Auto reply jumper J9 is installed as soon as the status of any input changes an SMS will be send to notify the user about the change only if the change in input state persists longer than 10 seconds an SMS will be send every time the status of any input changes for longer than 10 seconds If Auto Reply jumper J9 is not installed no SMS s will be send on input status change Cell Number After power up the GS2. GSM Relay the board will power up your pc will indicate Installing device driver wait for the Driver to install successfully If unsuccessful unplug and re plug the USB cable to the board after a while as soon as the Driver has installed successfully unplug the USB cable from the board STEP2 Run the MikroBootloader USB HID program on the pc as soon as the program is open connect the board with the USB cable The USB icon on the screen will turn red you have only 5 seconds to click on connect otherwise the micro will automatically disconnect the USB connection the History window will indicate a connection to the target processor STEP3 Click on Browse for HEX file button Locate the XXX hex file that was saved to the Desktop Click on Begin Uploading a progress bar will indicate the status of the file loading when completed uploading leave the board connected the processor is now programming itself with the new file that was loaded the USB will disconnect as soon as the processor have completed its self programming the status led will light and network led will flash indicating the board is functional again Unplug the USB now the board can now be powered normally again Please contact info microinstruments co za for any enquiries or custom software applications for the GSM Relay board
3. 66215 22 10 2014 Wed 08 00 Number saved to memory 08 00 08 00 Relay On 08 01 08 01 Relay Off 08 0 MORA DIER m m lt bed Gsm 2 27622966215 U ZO Add0622959578 8 08 27 8 Secondary num saved 08 27 08 27 8 Relay On 08 27 08 27 STATUS Input1 OFF Input 2 OFF BATT 13 0 Vdc FS d6 E 07 34 Ve qmm 08 01 Gsm 2 27622966215 STATUS Input 1 OFF Input 2 OFF BATT 13 0 Vde Add0622959578 cy 08 02 Secondary num saved 08 03 08 03 RESET Complete Input 1 OFF Input 2 OFF BATT 13 0 Vdc 8 06 ff 07 35 e m m lt bed Gsm 2 27622966215 INPUTS CHANGED Input 1 ON Input 2 OFF BATT 13 2 Vdc 12 39 cy Secondary num saved 12 43 INPUTS CHANGED Input 1 ON Input2 OFF BATT 13 2 Vdc INPUTS CHANGED Input1 OFF Input2 OFF BATT 13 2 Vdc 3 Custom Software uploads Please visit our website at www microinstruments co za and locate MikroBootloader USB HID from the downloads page download and install the program on your pc Once custom code was received for your unit in e mail save the XXXX hex file to your desktop The Standard code is also available from this page Have a USB B cable ready and connected to your a USB port on your pc STEP1 Make sure the board is not powered from the power input terminals It will be powered from USB now Plug the USB B cable into the USB port on the
4. GSM Relay MMIC FRO INIS TIPUIMIE IN TS ELECTRONIC RESEARCH DEVELOPMENT www microinstruments co za Tel 012 548 1615 Fax 0866 16 2222 Pictures and description 1 User instructions 2 Software updates custom software updates and Downloads 1 TOP View of GSM Relay board ITITTTITTTT 2209 90777708 prac GSM Relay The GSM Relay is a GSM based controllable module from your cell phone with Two 2 inputs and one 1 Relay output The main idea for the unit was to reset Router boards on a wireless network which became inaccessible through the wireless Network however it can be used for lots of different applications control any electrical equipment monitor the voltage of your battery backups alarm system etc Custom code can be written for customers with different needs over the standard program loaded on date of purchase of the module customers can re program the new code onto the device themselves via the on board USB connection The unit feature a SELF PROGRAMMABLE micro Processor Explained later in the manual The module reacts on specified command SMS s received returns SMS s to the user and can also alert the user if anyone of the 2 inputs changes state 2 User Instructions The GSM Relay comes pre programmed with our standard version of the GSM Relay Software Insert a SIM card on the bottom of the board into the SIM card holder and secure the socket the SIM card pin request must be d
5. M Relay send a sms with text save to the units number The number will be saved as the primary number and a sms with text number saved will be returned to your phone The primary number have full control on the unit to change input names add and remove numbers etc Send sms with text add082 number to add a secondary number to the unit SMS with text sec num saved will be returned to your phone and to the secondary phone number The primary number have full control on the unit and can send commands etc to the unit without the secondary number being notified Any status request or commands list request from the secondary number will result in a sms only to the secondary number but any operational commands like reset or on etc will result in a sms to the Primary and secondary number Inputs Standard the unit will refer to Input1 and Input2 in a SMS the user can change this by sending the following 11xxxxxxxxxx Capital letter i with a 1 10 user characters eg l1leskom _ 5spaces at the end to fill the string as eskom is only 5 characters Or eg l1generator 1space at the end to fill the string generator is 9 characters Follow the same sequence for Input 2 renaming Output Relay 10 Amp contact current rating Common Normally Open Normally Closed terminals available on board from Relay with 3 way barrier terminal GSM Relay OPERATIONAL SCREENSHOTS gl96 ff 07 34 e m lt bed Gsm 2 276229
6. isabled Save the phone number of the SIM card to your phone Powering up the board connect 12 to 28 VDC on the 2 way terminal marked POS NEG 12 24vdc usually from backup batteries or a power supply if there is no battery backup system The Status LED on the board will light up to indicate that the GSM engine have booted up After about 3 to 5 seconds the network LED on the board will start flashing indicating a successful connection to a GSM network and after about 5 seconds the network led should blink slowly to indicate that it is in sync with the network and the GSM Relay is now ready to use GSM Relay USB SMS Commands SMScommand OUTPUT RELAY ACTION REPLY SMS TO SENDER Com or Commands N A Sends a SMS to user stating all commands accepted via SMS N A Stat or Status Returns a SMS showing device Status Status of both Inputs Battery input voltage Returns a SMS confirming Reset completed also includes the status of both Inputs and Battery input voltage por toner Sonicare is on Relay on Off Returns a SMS confirming Relay is Off Relay Off N A Saves the primary cell number be lost after total power failure N A Add a secondary number for notifications and control to the unit Res or Reset Relay activates for 5 sec 11XXXXXXXXXX x user name for input 1 max 10 Characters If name is less than 10 characters fill with spaces 2XXXXXXXXXX x user name
Download Pdf Manuals
Related Search