User Manual Tow-Pro Elite
Contents
1. 2 5 Mounting the remote head Tow Pro Elite remote head is designed to be mounted at a distance from the main unit allowing for a neat convenient installation and not impeding on lower leg airbags or driver leg room The Tow Pro Elite remote head is designed to be mounted on or around the vehicle dashboard and when installed correctly complies with Australian Design Rule ADR 21 which sets requirements for devices mounted on the dashboard Elite remote head can be mounted directly to the dashboard to the centre console or through a spare knock out switch panel and requires only two holes to be drilled as per the below diagram 2 0 3 0mm Applying the Knob Turn shaft fully Apply knob with or anti clockwise 0 aligned with the level marker on the bezel 010 0mm drill pilot hole first use spade bit 2 INSTALLATION NOTE Ensure push button activates correctly when installed onto surfaces with a thickness greater than 3 0mm 2 4 Active Calibration Active Calibration constantly monitors the vehicle s direction of travel and allows the Elite to learn and continuously confirm its mounting orientation This process occurs whilst the vehicle is moving and the brake is applied with or without a trailer connected and you will not even notice Active Calibration occurring When the Tow Pro Elite is first installed i2. offers a warranty in respect of its Products where the Products are purchased from an authorised distributor or reseller of Redarc by a person Purchaser on the terms and conditions and for the duration outlined below in this document Warranty 1 In this Warranty the term Products means 8 1 1 all products manufactured or supplied by Redarc excluding its solar products which are covered by Redarc s Solar Product Warranty and 1 2 any component of or accessory for any product in clause 1 1 manufactured or supplied by Offer and duration of product warranties 2 warrants that its Products will be free under normal application installation use and service conditions from defects in materials and workmanship affecting normal use for 2 years from the date of purchase Warranty Period 3 Where Product malfunctions or becomes inoperative during the Warranty Period due to a defect in materials or workmanship as determined by Redarc then subject to further rights conferred by the Australian Consumer Law on the Purchaser Redarc will in exercise of its sole discretion either 3 1 repair the defective Product 3 2 replace the defective Product or 9 3 3 provide refund to the Purchaser for the purchase price paid for the defective Product without charge to the Purchaser 4 The warranty given by Redarc in clause 3 covers the reasonable costs of delivery and installation of a
3. Brake Input Output Power BLUE BLACK Brake Ground ey XQ Recommended 43 5mm 11 5mm veal 2 INSTALLATION 2 1 Mounting the main unit The Tow Pro Elite should be mounted inside the vehicle using either screws or other secure fitting methods at the mounting points provided It is recommended to mount the unit in a location which allows access to the intended remote head location The Tow Pro Elite can be mounted in any orientation as long as the installation is secure and the main unit cannot move or change orientation once installed A change of orientation will affect the system calibration A CAUTION Ensure that the Tow Pro Elite is mounted securely in a fixed location Failure to mount in a fixed location will result in inaccurate braking force measurements and incorrect braking of the trailer CAUTION Ensure that the Tow Pro Elite is installed inside the vehicle and away from any environmental conditions that may cause damage including submersion in water salt spray and humidity Contact with these conditions can cause damage to the unit s circuitry and may cause erratic trailer braking gt gt CER NS A CUZ Do Not Mount to Cables Wiring
4. 9916151556 101 129 9 0 220 JNOA SIA JO 94034 1281000 95 3U 0 2 19 121 2949 95167 914 5504 aduenbas 141 SOW 034 seusey MOTISA 5 941 931 038 9456 pue 931944 3U JO PUE 931 F ddfld 59058 HUN YPM E SI MOTISA 931 941 used pausnd si 10U 941 y OPERATION 3 19 121 2 6015160991 100 SI yun y se UMO C JOU SI yoayd pue 104 ddns 949 9113 Se 1942910 1102119 wes woy 6921 19410 OU JEU 9 9 swe 3018 99229 194121 UO 1105 10 2949 GAY 146 97214 UO INJO 11005 JO 10945 p ljdde y YLM AZ pue UUM SI 121 10104 01 SI eU 5949 19 24 0 y9y1g 129000991 pue HEM YOW1d 1290009811 Ue Na y 1916 y 0
5. THE POWER OF Trailer Brake Controller ELITE EBRH ACCV2 TRAILER BRAKE CONTROLLER The Tow Pro Elite is an electric trailer brake controller designed to suit most common trailer braking applications whilst requiring minimal dash space and being simple to install and operate The Tow Pro Elite offers selectable Automatic or User Controlled trailer braking modes allowing the user to choose the braking style depending on the road or terrain conditions vehicle type or driver preference The Tow Pro Elite features Active Calibration which constantly monitors the direction of travel removing the need for an initial calibration process the unit will even calibrate with no trailer attached whilst maintaining the ability to mount in any orientation The unit is able to operate both electric and electric hydraulic trailer brakes and will operate from either 12V or 24V vehicle systems without the need for manual selection or extra components wiring The unit is also ADR compliant when installed as directed WARNINGS amp SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains IMPORTANT SAFETY INSTRUCTIONS for the Tow Pro Elite Brake Controller DO NOT OPERATE THE CONTROLLER UNLESS YOU HAVE READ AND UNDERSTOOD THIS MANUAL AND THE CONTROLLER IS INSTALLED AS PER THESE INSTALLATION INSTRUCTIONS A WARNING ENSURE THAT YOUR TRAILER BRAKES ARE INSTALLED AND ARE OPERATING CORRECTLY IMPROPERLY INSTALLED AND O
6. Over the last three decades our company has established a reputation as the power conversion specialist A 100 Australian owned company we have met the needs of customers in transport and other industries through exciting innovative thinking We believe in total customer satisfaction and practice this by offering our customers e Technical advice free of jargon and free of charge e Prompt turnaround of orders throughout Australia and globally e Friendly personalised professional service and product support In the unlikely event that a technical issue arises with a Redarc product customers are encouraged to initially contact the Redarc Technical Support Team on 08 8322 4848 or power redarc com au for prompt and efficient diagnosis and product support Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure The benefits of this Warranty are in addition to other rights and remedies available at law in respect of the Products and shall not derogate from any applicable mandatory statutory provisions or rights under the Australian Consumer Law Redarc Electronics Pty Ltd atf the Redarc Trust trading as Redarc Electronics
7. UOI NBUUOD s 9194 091290009 JOU JSOLW 81 94 51 197294 HINDI BU JO 4079 OU UO 111915 HOUS 1 91991 1461 3421 UO SNONUIUOD mo 9u nb s dnes 2 Ajqissod aim YOV 1g JO 95161 ajqissod ye you 37 94 95 1901 u ym dn 51461 Ajuo 037 Siym Ajwopues 2 5 ue 91581 141 941 10U UBM JO BWI Aue 16 9949 si 037 941 Aue ye 3339 si 137 94 gt be puodas puodas agouenbas 141 6 PERIODIC WARNING Ensure that your trailer brakes are installed and are operating correctly Improperly installed and or faulty trailer brakes can cause erratic vehicle or trailer behaviour with the potential to cause a road accident For this reason it is of utmost importance that your trailer braking system be installed maintained by a qualified installer Always check brakes at low speed each time a trailer is attached to your vehicle Immediately After Installation To be done by a qualified Auto Electrician Test the installation vehicle wiring Testin
8. or technician in accordance with the instructions of Redarc If the Product is found to be working satisfactorily on return to Redarc or upon investigation by Redarc the Purchaser must pay Redarc s reasonable costs of testing and investigating the Product in addition to shipping and transportation charges Where Redarc is in possession of the Product the Product will be returned to the Purchaser on receipt of the amount charged Any replaced Products or components of Products shall become the property of Redarc may in exercise of its sole discretion deliver another type of Product component of a Product different in size colour shape weight brand and or other specifications in fulfilling its obligations under this Warranty in the event that Redarc has discontinued manufacturing or supplying the relevant Product or component at the time of the Warranty claim or where such Product or component is superior to that originally purchased by the Purchaser provided that the claim is notified to Redarc in writing at the postal address or email Other conditions of Warranty address specified in clause 21 and includes 12 If the Purchaser acquired a Product for the purpose of resupply then this Warranty 5 1 details of the relevant expenses incurred by the Purchaser and shall not apply to that Product 5 2 proof of the relevant expenses having been incurred by the Purchaser 13 In particular the sale of a Product via a
9. whatever nature outside the control of 20 7 Warranty claims in respect of a Product must be made in writing to at the postal address or email address specified in clause 21 within the Warranty Period such claims must include the following 7 1 details of the alleged defect or fault and the circumstances surrounding the defect or fault internet website by a party that is not an authorised distributor or reseller of the Product will be deemed to be a resupply within the meaning of the Australian Consumer Law and will render this Warranty void as Redarc has no control over the Storage handling quality or safety of Products sold by such persons A Purchaser shall only be entitled to the benefit of this Warranty after all amounts owing in respect of the Product have been paid While Redarc warrants that the Products will be free from defects in materials and workmanship in the circumstances set out in this Warranty to the maximum extent permitted by law Redarc does not warrant that the operation of the Products will be uninterrupted or error free To the maximum extent permitted by law Redarc s determination of the existence of any defect and the cause of any defect will be conclusive Spare parts or materials for the Products are guaranteed to be available for a period of at least 2 years after purchase of the Products The agents officers and employees of any distributor or reseller of the Products and of Red
10. 5 for the list of flash patterns showing the cause amp recommended course of action for each of the conditions that may be detected 13 OPERATION 3 199 109 3U SI pue 100 SI 1942319 Huryeig 1 y99y9 91904 n319 JO amod Ajddns Jo 07 N3349 si 031 IUL JO 0015 Y39949 S00 910615 100 JLIHM si yun Ajddns amod 31189 219880 03194 2 9981091 5 Ul s 910829 38 gt A INJ 34 Y90949 y sey yun pue 9179 S 037 99 Bum J LIHM 1119119 Aue JO payeloosse pue y 5101291105 PUNOIG 0949 111919 uado yea1q SI 9194 syne Bum am 038 1112119 Aue JO 1960141 1461 eyesg 991 01 1901 ayes 3u UO yun BU WO HULIM 20949 n119 HOUS SI Huipnjou Syne am 41g 991 suo dad 5 GED Aue 10 18 121 3U 11010 UO 0 JUN Y39909 n3119 1101 SI BU pue 51 031941
11. D indicator The table below shows how the Tow Pro Elite will indicate Normal Operation of the unit NOTE LEDs will glow full brightness when gain control is adjusted or manual override is pressed After release of the gain control knob the LED brightness will reduce This is designed to be less intrusive on driver s vision at night indication User Controlled Sleep Mode Blue Breathing on button push Trailer Connected Solid Blue Solid Green Braking Blue to Red Green to Red 1 sleep Mode occurs when there is no trailer connected to the vehicle 2 Breathing as opposed to flashing is the LED gradually getting brighter until its brightest point and then gradually dimming until off 3 The LED will vary between the Mode Colour Blue or Green and Red depending on the braking force 3 7 Troubleshooting The Elite features sophisticated diagnostics to warn the operator of faults in the vehicle and trailer brake wiring Wiring faults are indicated by a series of colour coded flash patterns the Tow Pro Elite LED Even intermittent faults are detected and may be indicated until cleared The warning code can be cleared by unplugging the trailer for 1 minute then reconnecting A fault indication should not be ignored though as it is a warning amp if left unattended such wiring faults can become worse and may lead to deterioration or loss of trailer braking Please refer to the table on pages 14 amp 1
12. Looms 2 INSTALLATION 2 2 Wiring the brake controller NOTE Always refer to vehicle manufacturer specifications regarding the correct connection point for the brake light signal RED wire CAUTION Fuses or Circuit breakers of appropriate rating must be installed to protect the vehicle system Please refer to the installation instructions in this section for specific instructions on where to install Fuses or Circuit breakers and for appropriate Fuse or Circuit Breaker ratings Fuses must be installed as close as possible to the battery CAUTION Ensure that the cable used to install the Tow Pro Elite is of adequate thickness to supply the required current to operate the trailer brakes Incorrect wiring can result in overheated wires and may cause injury to persons damage to the Elite and or damage to property NOTICE The Tow Pro Elite does not act as a trailer lights voltage converter The Tow Pro Elite is designed to operate the trailer brake lights under certain conditions If the trailer brake lights require a different voltage to the input from the vehicle damage to the trailer brake lights may result 12V Vehicle Battery 30A Circuit To 12V Trailer Brakes To 12V Vehicle Brake Lights Dash mount controls for Tow pro 2 INSTALLATION White 24V Vehicle 30A Circuit Battery Breaker To 12V Trailer Brakes To 24V Vehicle Brake Lights Dash mount controls for
13. R FAULTY TRAILER BRAKES CAN CAUSE ERRATIC VEHICLE OR TRAILER BEHAVIOUR WITH THE POTENTIAL TO CAUSE A ROAD ACCIDENT FOR THIS REASON IT IS OF UTMOST IMPORTANCE THAT YOUR TRAILER BRAKING SYSTEM BE INSTALLED MAINTAINED BY A QUALIFIED INSTALLER ALWAYS CHECK BRAKES AT LOW SPEED EACH TIME A TRAILER IS ATTACHED TO YOUR VEHICLE A CAUTION 1 Ensure that the Tow Pro Elite is mounted securely a fixed location Failure to mount in a fixed location will result in inaccurate braking force measurements and incorrect braking of the trailer 2 Ensure that the Elite is installed inside the vehicle and away from any environmental conditions that may cause damage including submersion in water salt spray and humidity Contact with these conditions can cause damage to the unit s circuitry and may cause erratic trailer braking SAL FOR Instruction Manual EBRH ACCV2 Version 1 4 WARNINGS amp SAFETY INSTRUCTIONS 3 Fuses or Circuit breakers of appropriate rating must be installed to protect the vehicle system Please refer to the installation instructions on page 6 for specific instructions on where to install Fuses or Circuit Breakers and for appropriate Fuse or Circuit Breaker ratings Fuses must be installed as close as possible to the battery 4 Ensure that the cable used to install the Tow Pro Elite is of adequate thickness to supply the required current to operate the trailer brakes Incorrect wiring can result in over
14. arc are not authorised to vary or extend the terms of this Warranty Redarc shall not be responsible or liable to the Customer or any third party in connection with any non performance or delay in performance of any terms and conditions of this Warranty due to acts of God war riots strikes warlike conditions plague or other epidemic fire flood blizzard hurricane changes of public policies terrorism and other events which are beyond the control of Redarc In such circumstances Redarc may suspend performance of this Warranty without liability for the period of the delay reasonably attributable to such causes a clause or part of a clause in this Warranty can be read in a way that makes it illegal unenforceable or invalid but can also be read in a way that makes it legal enforceable and valid it must be read in the latter way If any clause or part of a Clause in this Warranty is illegal unenforceable or invalid that clause or part is to be treated as removed from this Warranty but the rest of this Warranty is not affected 7 2 evidence of the claim including photographs of the Product where the subject Redarc s contact details of the claim is capable of being photographed 21 Redarc s contact details for the sending of Warranty claims under this Warranty are number of the Product specified the label affixed to the Product Redarc Electronics Pty Ltd 7 4 proof of purchase documentation for the Product from an
15. authorised distributor as oe North Lonsdale SA 5160 or reseller of Redarc which clearly shows the date and place of purchase mail power redarc com au The return of any Products without the prior written instructions of Redarc will not Telephone 61 8 8322 4848 be accepted by Redarc 18 THE POWER OF Free technical assistance please contact Redarc Electronics 23 Brodie Road North Lonsdale SA 08 8322 4848 power redarc com au www redarc com au Mailing Address PO Box 469 Morphett Vale south Australia 5162 Australian Registered Design 352577 Australian Registered Design 352578 Australian Registered Design 352674 Australian Patent Application 2014900483 Pending Copyright 2015 Redarc Electronics Pty Ltd All rights reserved WAREBRH ACCV2 REV1
16. ect the electric hydraulic mode Tow Pro Elite is not suitable for electric hydraulic systems which only operate from their own dedicated brake control system Tow Pro Elite will operate electric hydraulic trailer brakes in either Automatic or User Controlled modes NOTE Always refer to manufacturer specifications for your Electric Hydraulic Braking system prior to installation and usage of the Tow Pro Elite Most Electric Hydraulic braking systems will require a seperate 12V power feed for the hydraulic pump 3 4 24V Vehicle Systems Tow Pro Elite is designed to operate 12V trailer brakes from both 12V and 24V vehicle electrical systems The acceptable voltage input range is between 9V and 32V The Tow Pro Elite will operate from 24V electrical system without the need for other external devices For 24V installation refer to section 2 2 Wiring the brake controller 11 3 OPERATION 3 5 Visual User Guide Automatic Mode Blue LED Colour Lighter Heavier Trailer Trailer Brake Applied Light Application of Trailer Brakes only User Controlled Mode Green LED Colour Lighter Heavier Brake Brake Force Force Brake Applied Applies Trailer Brakes only to the level set on the gain control knob 3 OPERATION 3 6 LED Indication Tow Pro Elite will indicate both Mode and Fault Condition through colour and flash sequences of the LE
17. ed mode NOTE Itis important to consider the road surface and conditions when you are selecting your mode and level setting When changing conditions we advise to review your controller settings and adjust according to your preference NOTE Changing modes can only be completed with the trailer connected NOTE Ensure the vehicle has come to a complete stop before beginning the mode change process Changing between modes requires the user to complete the following process 1 Set the knob to 0 fully counter clockwise 2 Apply vehicle brakes 3 Double click the knob i e two pushes within 1s to toggle the mode 4 Release vehicle brakes NOTE Ensure you reset the dial to an acceptable braking level after changing modes Everytime the vehicle is turned on the 7 Elite will start up the mode that was last selected providing the black wire has remained connected to power battery positive 3 OPERATION 3 1 1 Automatic Mode Blue LED the status indication LED on the control knob is glowing BLUE the Tow Pro Elite is in Automatic Mode When operating in Automatic Mode the Tow Pro Elite will apply the trailer brakes at a level proportional to the vehicle deceleration Simply put the harder you brake the harder the trailer will brake This mode is designed for highway travelling or everyday use and requires minimal input from the user whilst travelling The braking level can be adjusted to suit varying t
18. es have the power to order the combination off the road until the issue is corrected This may necessitate leaving the trailer on the side of the road while a vehicle with suitable towing capacity is sourced or the trailer load is reduced Please contact your local authorities for further information CONTENTS Table of Contents Page Contents 03 1 Specifications 03 2 Installation 05 2 1 Mounting the main unit 05 2 2 Wiring the brake controller 06 2 3 Mounting the remote head 07 2 4 Active Calibration 08 3 Operation 09 3 1 Operating Modes 09 3 2 Manual Override 11 3 3 Electric Hydraulic Brakes 11 3 4 24V vehicle systems 11 3 5 Visual User Guide 12 3 6 LED Indication 13 3 7 Troubleshooting 13 4 Periodic Maintenance Checks 16 5 Frequently Asked Questions 17 6 Warranty 18 SPECIFICATIONS art Number EBRH ACCV2 ____ 127 ominal Input System Voltage perating Voltage 9V 32V 9V 32V Brake Input Signal Voltage OFF OV OFF OV ON 12V nominal ON 24V nominal rake Coil Voltage Max Trailer Axles Max Rated Current 30A tandby Current lt 10 perating Temp Weight 1 SPECIFICATIONS Kit Contents Remote Head Assembly Main Unit Remote Head Nut Remote Head Knob Remote Head Bezel RJ45 Remote Head Cable 1m Main Unit Wires amp Connector 0 5m e Dimensions amp Connection Remote Head Connection
19. g your vehicle wiring is best done by connecting a test light 21W filament globe to the brake light output pushing the manual override and having someone check that the vehicle brake lights and the test lamp both light up Before each trip It is important to ensure that your system is operating correctly before you set out The following should be checked along with standard mechanical maintenance each time you attach your trailer e Correct brake light operation on both your vehicle and trailer e Correct operation and setting of the electric brake controller e Correct operation of your trailer brakes e Check that your breakaway system is operating correctly and that the breakaway battery is healthy e Ensure that the tow hitch and safety chains and weight distribution systems are setup correctly Periodically It is important to have a qualified technician check the function of your trailer system on a periodic basis to ensure that everything is operating correctly Redarc recommend that you visit a qualified technician before the beginning of each holiday season to ensure that any towing aids or systems are working correctly Other considerations Please consider the below items whilst towing a trailer e Ensure that your vehicle is capable of towing the trailer e Ensure that you adjust your driving style to allow more time to change lanes and brake e Always remember that your electric brake controller is designed to supplement yo
20. heated wires or excessive voltage drop and may cause injury to persons damage to the Elite and or damage to property 5 Elite is suitable for all trailers with electric brakes on up to three axles Note that for trailers above 4 5t gross special testing is required under Australian Design Rules For these trailers please consult with an automotive safety engineer before using the Tow Pro Elite NOTICE 1 Ensure that a correct grounding point is used Vehicles often have ungrounded metal reinforcements under the dash and these points are not suitable grounds Bad grounding of the unit will result in poor or no operation 2 The Tow Pro Elite does not act as a trailer lights voltage converter The Tow Pro Elite is designed to operate the trailer brake lights under certain conditions the trailer brake lights require a different voltage to the input from the vehicle damage to the trailer brake lights may result When installing the Elite Remote Controls to a thin panel washers are recommended to reinforce the structure of the panel 4 DoNOT exceed Tow Vehicle and Trailer weights and specifications Failure to abide by the towing regulations including maximum loads may result in a fine or in case of an accident refusal of the insurance claim and the possibility of further legal action lf the tow vehicle or trailers maximum load is exceeded police and transport authoriti
21. n online auction online store or other Exclusions and limitations 6 This Warranty will not apply to or include any defect damage fault failure or malfunction of a Product which Redarc determines in exercise of its sole discretion to be due to 6 1 normal wear and tear or exposure to weather conditions over time 14 6 2 accident misuse abuse negligence vandalism alteration or modification 6 3 non observance of any of the instructions supplied by Redarc including 19 instructions concerning installation configuring connecting commissioning use or application of the Product including without limitation choice of location 6 4 failure to ensure proper maintenance of the Product strictly in accordance with Redarc s instructions or failure to ensure proper maintenance of any associated 16 equipment or machinery 6 5 repairs to the Product that are not strictly in accordance with Redarc s 17 instructions 6 6 installation repairs or maintenance of the Product by or under the supervision 18 of person who is not a qualified auto electrician or technician or if non genuine or non approved parts have been fitted 19 6 7 faulty power supply power failure electrical spikes or surges lightning flood storm hail extreme heat fire or other occurrence outside the control of 6 8 use other than for any reasonable purpose for which the Product was manufactured 6 9 any indirect or incidental damage of
22. ny repaired or replaced Products or components of Products 10 to the Purchaser s usual residential address notified to Redarc together with the reasonable costs of removal and return of any Products determined by Redarc to be 11 defective 5 If the Purchaser incurs expenses of the nature referred to in clause 4 in the context of making a claim pursuant to this Warranty that is accepted by Redarc the Purchaser will be entitled to claim for reimbursement of those expenses which Redarc determines in exercise of its sole discretion to be reasonably incurred Without limiting any other clause in this Warranty Redarc has the right to reject any Warranty claim made by a Purchaser pursuant to this Warranty where 8 1 the Purchaser does not notify Redarc in writing of a Warranty claim within the Warranty Period 8 2 the Purchaser does not notify Redarc in writing of a Warranty claim within 1 month of becoming aware of the relevant circumstances giving rise to the claim so that any further problems with the Product are minimised 8 3 the serial number of the Product has been altered removed or made illegible without the written authority of Redarc 8 4 the Purchaser is unable to provide proof of purchase documentation in accordance with clause 7 4 or evidence that the Product was properly installed and removed if relevant and that proper maintenance has been performed on the Product by or under the supervision of a qualified auto electrician
23. once braking requirements are established should a lighter braking level be required turning the gain control knob to a lower number will reduce the trailer braking force Similarly turning the gain control knob to a higher number will increase the trailer braking force The braking level will be indicated by the LED changing to a shade of RED when the brakes are applied The higher the braking level the more RED the LED will glow 10 3 OPERATION 3 2 Manual Override Pressing the gain control knob whilst driving will apply the manual override brake The manual override brake will apply the trailer brakes only and will also apply the vehicle brake lights trailer brake lights and will turn the LED indicator a shade of RED The manual override is designed to be used when the trailer brakes need to be applied without the vehicle brakes such as correcting trailer sway whilst travelling In Automatic mode the manual override will apply the trailer brake to a level equivalent to light vehicle braking In User Controlled mode the manual override will apply the trailer brakes to the level set on the gain control knob In both modes the braking force can be adjusted by turning the gain control knob either higher or lower whilst applying the manual override brakes 3 5 Electric Hydraulic Brakes The Tow Pro Elite is designed to operate both electric and electric hydraulic braking systems The unit requires no user input to sel
24. railer loads braking requirements or user comfort by adjusting the gain control knob on the remote head The middle point level 5 should be used as a starting point please refer to section 3 5 for more information should a lighter braking level be required turning the gain control knob below 5 will reduce the trailer braking force relative to the vehicle braking level Similarly turning the gain control knob above level 5 will increase the trailer braking force relative to the vehicle braking level The braking force will be indicated by the LED changing to a shade of RED when the brakes are applied The higher the braking force the more RED the LED will glow 3 1 2 User Controlled Mode Green LED the status indication LED on the control knob is glowing GREEN the Elite is in User Controlled Mode When operating in User Controlled Mode the Tow Pro Elite will apply the trailer brakes to the level set by the user on the gain control knob The gain control level 0 to 10 will set the brakes from Zero trailer braking to Full trailer brake application This mode is often preferred for offroad or precision use and may require frequent attention from the user The braking level can be adjusted to suit varying trailer loads braking requirements or user comfort by adjusting the gain control knob on the remote head The lower of the scale below level 5 should be used as a starting point and adjusted accordingly
25. t will begin learning its mounting orientation through Active Calibration as soon as you start driving at this point Automatic Mode is selected but not yet fully operational Until the Elite has determined its mounting orientation the unit will function as if in User Controlled mode this is indicated by the LED glowing green with blue flashes As the Elite becomes more confident of its direction of travel the length of the Blue flash will increase to the point that the LED is solid Blue which indicates it is now operating completely in Automatic mode Under normal driving conditions the 7 Elite will learn its mounting orientation within 20 brake applications Note that the braking must be perceptible applying the brake while stopped will not assist calibration For the most rapid calibration process 10 second bursts of firm braking are best lf no trailer is connected Active Calibration will occur as normal without any indication from the LED The LED will already be Blue when the trailer is connected Essentially whether a trailer is connected or not just drive normally and Active Calibration will ensure the Elite learns the correct direction of travel 3 OPERATION 3 1 Operating Modes The Tow Pro Elite offers two modes of operation Automatic and User Controlled On the first application of power to the black wire the 7 Elite will start up in User Controll
26. trong enough to stop that much weight safely The controller is capable of supplying 3 axle setups at 12V or 24V inputs up to the maximum rated braking ability of the brakes You must also ensure that your trailer brakes are adequate for the trailer load Can the remote head cable be extended Yes the remote head cable is a standard RJ45 network cable and can be replaced by an off the shelf cable up to 5m in length If the cable used is longer than 1m however we recommend using a ferrite bead such as Jaycar P N LF1294 clipped onto the cable as close as possible to the main unit Can the braking level of the manual over ride be adjusted Yes the manual override can be adjusted whilst it is being applied by turning the gain control knob For more information on manual override please see section 3 2 of this manual Will my trailer brakes work while am reversing The Elite is designed to apply the trailer brakes whether the vehicle is travelling forward or in reverse The effectiveness of the brake application in reverse will depend on the mechanical design of your particular electric brake system have 2 axle trailer is the Tow Pro Elite suitable for my trailer Yes the Elite is designed to operate up to 3 axle trailers 1 lost the knob nut bezel where get one The knob nut or bezel can be purchased as spare parts from Redarc authorised resellers 17 6 TWO YEAR PRODUCT WARRANTY
27. ur vehicle brakes do NOT use the Tow Pro Elite manual override in place of your vehicle foot brake e Redarc recommend professional towing training before attempting to tow a trailer companies such as Tow Ed offer these services 9 FREQUENTLY ASKED QUESTIONS Is the Tow Pro Elite approved to use with the my Electronic Trailer Stability Control system Tow Pro Elite is approved for use with the AL KO ESC and the Dexter Sway Control systems Please visit the manufacturers website for more information How do I change from Automatic to User Controlled mode Please see section 3 1 of this manual Will it work with electric over hydraulic trailer brakes Yes please see section 3 3 of this manual Can it be mounted in any orientation How do set the levelling of the main unit Yes the unit can be installed inside the vehicle at any angle provided it is firmly secured and in a location which allows access to the intended remote head location Please see sections 2 1 and 2 4 of this manual for more information My vehicle has shared tail brake lights will the Tow Pro Elite work OK Yes the Tow Pro Elite is designed to operate correctly from both standard and shared tail brake lights Where can connect the RED wire To a 12V ON OV OFF switched wire when brake pedal applied refer to the vehicle manufacturer specifications for the correct location My caravan is 2 5 tons fully loaded is the Tow Pro Elite s
Download Pdf Manuals
Related Search