FREQ Matrix Quad
Contents
1. SH X will now be displayed X representing a number between 0 8 Shows 1 8 are preset shows while SH 0 is random show Press the UP or DOWN buttons to find your desired show System Menu 3 Once you have found your desired show press ENTER and then press and hold the MENU button for at least 3 seconds to confirm SOUN tn this submenu you can activate sound active mode 1 Press the MENU button until SOUN is displayed press ENTER 2 Either ON or OFF will now be displayed Press the UP or DOWN buttons to select one or the other 3 When you have made your selection press the ENTER and then press and hold the MENU button for at least 3 seconds to confirm SENS sound sensitivity control 1 Press the MENU button until SENS is displayed press ENTER 2 The display will show a number between 0 100 Press the UP or DOWN buttons to adjust the sound sensitivity 0 being the least sensi tive and 100 the most sensitive 3 Press the ENTER and then press and hold the MENU button for at least 3 seconds to confirm DNST This mode can be used as a precaution mode that in case the DMX signal is lost the operating mode chosen in the setup is the running mode the fixture will go into when the DMX signal is lost You can also set this as the operat ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 9 FREQ Matrix Quad System Menu ing mode you would like th2. 1 The FREQ Matrix Quad has 4 DMX Modes a 2 Channel Mode 5 Channel Mode 18 Channel Mode amp 64 Channel Mode See pages 14 17 for a detailed description of the DMX traits 2 To control your fixture in DMX mode follow the set up procedures on pages 8 9 as well as the set up specifications that are included with your DMX controller 3 Use the controller s faders to control the various DMX fixture traits This will allow you to create your own programs 4 Follow the instructions on page 8 to select your desired DMX Mode and to set the DMX address After you have selected your DMX mode and set the address then connect your DMX control ler 5 For longer cable runs more than a 100 feet use a terminator on the last fixture 6 For help operating in DMX mode consult the manual included with your DMX controller Sound Active Mode This mode allows a single unit or several units linked together to run to the beat of the music 1 Press the MENU button until SOUN is displayed and press ENTER 2 Press the UP or DOWN buttons until ON is displayed and press ENTER and then press and hold the MENU button to confirm 3 To adjust the sound sensitivity press the MENU button until SENS is displayed Use the UP or DOWN buttons to adjust sen sitivity See page 9 for more info 4 The optional UC3 Controller not included may be used to con trol different functions including blackout See page 13 for UC3 controls a
3. 4a Rev 2 15 DJ FREQ MATRIX J QUAD O O O O O D O Q User Instructions 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indi rect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent assembly installation rigging and operation of this product E
4. E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting S
5. WHITE 16 0 100 ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 17 FREQ Matrix Quad With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 2 fixtures maximum After 2 fixtures you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures FREQ Matrix Quad Locate and remove the unit s power cord Once the cord has been removed located the fuse holder located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse FREQ Matrix Quad Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses must be carried out periodically to optimize light output Power Cord Daisy Chain Fuse Replacement Cleaning 1 Use a soft cloth to wipe down the outside casing Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew FREQ Matrix Quad Listed below are a few common problems the user may encounter with solutions Trouble Shooting Unit not responding to DMX 1 Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on some other DMX devices
6. Show Mode Manual Mode and DMX Control Sound Sensitivity Adjustable UC3 Remote Control Compatiable Not Included Power Cord Daisy Chaining See page 18 FREQ Matrix Quad The FREQ Matrix Quad carries a 2 year 730 days limited warranty Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www adj com All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact ADJ Products LLC cus tomer support for a R A number FREQ Matrix Quad Warranty Registration Installation The unit should be mounted using a mounting clamp not provided affixing it to the mounting bracket that is provided with the unit Always ensure that the unit is firmly fixed to avoid vibration and slip ping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit s weight Also always use a safety cable that can hold 12 times the weight of the unit when installing the fixture The equipment must be installed by a professional and it must be installed in a place where it is out of the reach of people s grasp ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 3 FREQ Matrix Quad Safety Preca
7. MENU button until SLND is display ed and Press ENTER Use the UP or DOWN buttons to switch between either SL 1 or SL 2 Once you have made your choice press ENTER For more info see page 8 4 The slave units will now follow the Master unit 5 The optional UC3 Controller not included may be used to con trol different functions including blackout See UC3 Control below FREQ Matrix Quad UC3 Control Blackout Blackout the unit Strobe 7 Color1 9 Function 1 Synchronous strobe in white Show1 8 Color10 Sound 2 Sound strobe in white Change Color 3 Sound strobe in color Mode Strobe Manual Color Show LED OFF LED ON LED slow blinking ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 13 Function FREQ Matrix Quad 2 Channel Mode DIMMER 0 100 STROBING OPEN STROBING SLOW FAST FREQ Matrix Quad Photometric Chart RGBW 1348 337 150 84 54 R 388 97 43 24 15 5 G 589 147 65 37 24 B 121 30 13 7 5 5 lux w 574 144 64 36 23 Distance m 0 1 0 2 0 3 0 4 0 ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 14 Matrix Quad 5 Channel Mode Value Function Be 255 0 100 GREEN M net 0 100 BLUE 0 ME 0 100 EA Rs vik 0 255 0 100 STROBING 0 15 OPEN 16 131 STROBING SLOW FAST 132 139 OPEN 140 181 SLOW OPEN FAST CLOSE 18
8. board 1 Press the MENU button until ADDR is displayed press ENTER 2 X will now be displayed X represents the displayed address Press the UP or DOWN buttons to find your desired address 3 Press ENTER to confirm then connect your DMX controller NOTE lf after you connect your DMX controller the unit does not fall into DMX mode press and hold the MENU button for at least 3 seconds CHND This will let select your desired DMX channel mode 1 Press the either the MENU button until CHND is displayed press ENTER Either 2CH 5CH 18CH or 64CH will be displayed 2 Press the UP or DOWN buttons to find your desired DMX channel mode and press ENTER to confim and exit SLND This will let you set unit as a master or slave ina master slave configuration 1 Press the MENU button until SLND is displayed press ENTER Either SL 1 or SL 2 will be displayed 2 Press the UP or DOWN buttons until your desired setting is displayed press ENTER to confim NOTE In a Master Slave configuration you can set one fixture to Slave 1 SL 1 and then set the next fixture to Slave 2 SL 2 in doing this the fixtures will now have contrast movement to each other SHND SH 0 SH 8 Show modes 0 8 ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 8 FREQ Matrix Quad 1 Press the MENU button until SHND is displayed press ENTER 2
9. from heat sources such as radiators heat registers stoves or other appliances inclu ding amplifiers that produce heat The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 4 FREQ Matrix Quad Y a Uo Power Supply The ADJ FREQ Matrix Quad contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and
10. the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The FREQ Matrix Quad has 4 DMX Channel modes The DMX address is set on the rear panel of the FREQ Matrix Quad Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for data input and data output We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all professional sound and lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Figure 1 ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 5 FREQ Matrix Quad Set Up Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con n
11. written notice ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 22 ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www adj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On HOM facebook com americandj twitter com americandj youtube com adjlighting
12. 2 189 OPEN 190 231 FAST OPEN SLOW CLOSE 232 239 OPEN 240 247 SOUND ACTIVE STROBING 248 255 OPEN CHE VEDETE 18 Channel Mode Value Function 0 255 0 100 ons one t0606 0 255 0 100 DENTINE ee 0 255 0 100 WHITE Top Row 0 100 RED 2nd Row 0 100 GREEN 2nd Row 0 100 BLUE 2nd Row 0 100 WHITE 2nd Row 0 255 0 100 ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 15 0 E 0 255 O 295 0 255 FREQ Matrix Quad 18 Channel Mode Value Sanner o om O 0 oss 0 255 T ozs 1 SS pL oms O oms 1 1 132 139 140 181 182 189 190 231 232 239 240 247 248 255 Function RED 3rd Row 0 100 GREEN 3rd Row 0 100 BLUE 3rd Row 0 100 WHITE 3rd Row 0 100 RED 4th Row 0 100 GREEN 4th Row 0 100 BLUE 4th Row 0 100 WHITE 4th Row 0 100 MASTER DIMMER 0 100 STROBING OPEN STROBING SLOW FAST OPEN SLOW OPEN FAST CLOSE OPEN FAST OPEN SLOW CLOSE OPEN SOUND ACTIVE STROBING OPEN ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 16 64 Channel Mode Function RED 1 0 100 0 100 E e 0 100 O o 0 100 RED 2 0 100 GREEN 2 0 100 BLUE 2 0 100 WHITE 2 0 100 FREQ Matrix Quad BLUE 15 0 100 WHITE 15 0 100 O os oo 0 100 rr 0 100 BLUE 16 0 100
13. ates If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect
14. e unit to return to when power is applied 1 Press the MENU button until DNST is displayed press ENTER 2 Either MASL BLND or LAST will be displayed Choose an operating mode you would like the unit to start up in when power is applied or the DMX signal is lost e MASL Master Slave If the DMX signal is lost or power is applied the unit will automatically go into Master Slave mode e BLND Blackout If the DMX signal is lost or power is applied the unit will automatically go into stand by mode e LAST Last State If the DMX signal is lost the fixture will stay in the last DMX set up If power is applied and this mode is set the unit will automatically go into the last DMX set up 3 Press ENTER to confirm your desired set up LED With this function the LED display will turn off after 2 minutes 1 Press the MENU button until LED is displayed press ENTER 2 Either ON or OFF will now be displayed Press the UP or DOWN buttons to select ON to keep the LED display on at all times or OFF to allow the LED display to turn off after 2 min utes Press any button to turn the LED display on again 3 Press ENTER to confirm your selection DISP This will flip the LED display 1 Press the MENU button until DISP is displayed press ENTER 2 When DISP is displayed the LED display will remain normal ADJ Products LLC www adj com FREQ Mat
15. ect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 aA aen aaa OO agen A T 7 XLR Male Socket XLR Female Socket i XLR Pin Configuration I 1 1 1 Ground 1 2 Cold 2 Cold 1Ground 1 Pin 1 Ground I 1 Pin 2 Data Compliment negative I 1 1 i 3 Hot 3 Hot l Pin 3 Data True positive E EE E E E E E E E EE 4 Figure 3 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems 2 and interference It is always advisable A 8 to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3
16. nd functions Show Mode This mode allows a single unit or several units linked together to run a selected show 1 Press the MENU button until SHND is displayed and press ENTER 2 Press the UP or DOWN buttons until you find your desired show ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 12 FREQ Matrix Quad Operation press ENTER then press and hold the MENU button to confirm Please see pages 8 9 for more info about Show Mode The optional UC3 Controller not included may be used to con trol different functions including blackout See below for UC3 controls and functions o FREQ Matrix Quad Master Slave Set Up Master Slave Operation This function will allow you to link up to 16 units together and operate without a controller In Master Slave opera tion one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Using appropriate XLR cables daisy chain your units together via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a terminator at the last fixture 2 Set the Master unit to your desired operational mode 3 On the slave units tap the
17. oducts LLC provides a toll free cus tomer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ Products LLC PLEASE recycle the shipping carton when ever possible ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 2 FREQ Matrix Quad To optimize the performance of this product please read these operat ing instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference General Instructions FREQ Matrix Quad Features Built in Microphone 4 DMX Channel Modes 2 Channel Mode 5 Channel Mode 18 Channel Mode amp 64 Channel Mode 12 Show Modes 4 Operating Modes Sound Active
18. pin 2 may be hot Also check that all cables are connected to the right connectors it does matter which way the inputs and outputs are connected Unit does not respond to sound 1 Quiet or high pitched sounds will not activate the unit If problems are not resolved Contact ADJ Products LLC for service 1 800 322 6337 ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 18 FREQ Matrix Quad Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United St
19. pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor 3 Pin XLR Female Out 5 Pin XLR Male In Ground Shield Pin 1 Data Compliment signal Pin 2 Data True signal Pin 3 Notuses pS Not Used Do Not Use Do Not Use ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 6 FREQ Matrix Quad System Menu Muy jee Hiag cI DMX 512 Address oth Cand ae Channel Mode SCR SLid Su Slave Mode Shig Show Mode MENU Solin FF Sound Mode SEAS eae Sound Sense MASE dhStl totic DMX State CASE mas an LED on oF F LED off aoo oi Normal dS E Inversion rest Self test cene Temperature Test rhe Fixture Hours D uo Software version ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 7 FREQ Matrix Quad System Menu ADDR DMX Address Setting via control
20. rix Quad Instruction Manual Page 10 FREQ Matrix Quad System Menu when DSIP is displayed the LED display will be flipped Use the ENTER button to find your desired display set up then press MENU to confirm and exit TEST This function will run a self test program 1 Press the MENU button until TEST is displayed press ENTER 2 The fixture will now run a self test Press the MENU button to exit TEMP With this function you can check the current tem perature of the fixture 1 Tap the MENU button until TEMP is displayed press ENTER 2 The current temperature of the fixture will now be displayed Press MENU to exit FHRS with this function you can display the running time of the unit 1 Press the MENU button until FHRS is displayed press ENTER 2 The running time of the fixture will now be displayed Press MENU to exit VER This will display the software version 1 Press the MENU button until VER is displayed Press the ENTER button and the software vesion will be displayed 2 Press the MENU button to leave this function ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 11 FREQ Matrix Quad Operation Universal DMX Control This function allows you to use a Elatione universal DMX 512 controller to control the chases and patterns dim mer and strobe A DMX controller allows you to create unique pro grams tailored to your individual needs
21. tands etc excluding LED Laser Products and lamps e Laser Products 90 Day Limited Warranty e L E D Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty Only the L E D s carry a 3 year warranty ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 19 FREQ Matrix Quad Notes FREQ Matrix Quad Notes ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 20 ADJ Products LLC www adj com FREQ Matrix Quad Instruction Manual Page 21 FREQ Matrix Quad Specifications Model FREQ Matrix Quad Voltage 100V 240V 50 60Hz LEDs 16 x 8W 4 in 1 RGBW LEDs Power Consumption 152W Fuse 7Amp Power Cord Daisy Chain 2 Fixtures Max Weight 15lbs 6 6Kgs Dimensions 12 5 L x 6 5 W x 13 25 H 310 x 163 x 334mm Colors RGBW Beam Angle 120 Degrees DMX Channels 4 DMX Channel Modes 2 Channel Mode 5 Channel Mode 18 Channel Mode amp 64 Channel Mode Any safe working position 4 Hours Max 2 Years 730 days Working Position Duty Cycle Warranty Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior
22. urope Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipment from power when not in use Thank you FREQ Matrix Quad Introduction Unpacking Thank you for purchasing the FREQ Matrix Quad by ADJ Products LLC Every FREQ Matrix Quad has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during ship ping If the carton appears to be damaged carefully inspect your fix ture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are missing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contacting customer support Introduction The FREQ Matrix Quad is part of ADJ s continuing pur suit for creating high quality affordable intelligent fixtures The FREQ Matrix Quad is a revolutionary 16 zone LED strobe The unit has 3 operating modes Sound Active Show Mode or DMX Control This unit can be used as a stand alone fixture or in a Master Slave configu ration This fixture is suitable for theaters studios retail stores and other similar locations Customer Support ADJ Pr
23. utions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short e Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside e Never operate this unit when it s cover is removed e Never plug this unit in to a dimmer pack e Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged e This unit is intended for indoor use only use of this product out doors voids all warranties e During long periods of non use disconnect the unit s main power e Always mount this unit in safe and stable matter e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit e Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 18 for cleaning details e Heat The appliance should be situated away
Download Pdf Manuals
Related Search