Home

UG TVP-224HR v7

1. 113 TVP 224HR User s Guide FXO Port Pin Assignments The FXO Telephony Interface Module has 2 RJ11C W modular jacks The following diagram and table show the assignments of the pin for the RJ11 port RJ 11 pin Signal 1 Not connected 2 Tip 3 Ring 4 Not connected 1 2 3 4 FXS Port Pin Assignments The FXS Telephony Interface Module has 2 RJ11C W modular jacks The following diagram and table show the assignments of the pin for the RJ11 port RJ 11 pin Signal 1 Not connected 2 Tip 3 Ring 4 Not connected 1 2 3 4 114 TVP 224HR User s Guide Appendix B Connecting through Console The console port uses a DB 9 RS 232 connector The supplied straight through RS 232 cable connects the console port of the TVP 224HR to a console PC or terminal CO eom e Connect RS 323 Cable to TVP 224HR RS 232 console port a your computer that you will use as a configuring terminal Open HyperTerminal and enter the following Input Baud rate Parameters when prompted Number of data bit 19 200 Parity check 8 Number of stop None bit 1 Flow control None When the empty HyperTerminal Screen appears 123 type 123 In the event that you forget your administration password you can gain console access to the TVP 224HR using the super password The super password is the last six digit
2. 80 Hunt Group Table 63 73 88 Default DTMF Mode 69 I desktop ooooooocnoccocccoconononononninnnonos 17 destination oooooncnnoconococononnnonnnonos 61 ICMP icenic nienti 4 Destination ID Table 74 MTC 4 Destination Table 63 88 Incoming Fast Start 68 OA E 90 InstalliMQ o ooooooooooi oco o o 17 Dial Plannin 72 82 87 Inter Digit Wait Time 78 Dial Plan Setup o 72 85 Interface Speed 79 Display Name ccceeceereees 68 Internet Telephony Gateway 12 Download Mode c0cc008 112 IP Parameter ccccceceeeeees 115 Bo gee ae eee eee eee 4 DI a ee 4 61 DTMF Duration cooococcconcnnninnnono 69 AA teresa 12 DTMF relay c eee 63 107 A aulig aiiavictetscievcess 4 L E LAN Port eresas 109 Endpoint Prefix coccion 70 LED icnaos 4 15 126 Aa a ie ere E 77 M Max Registration Retries 70 Max Digits 73 Min Digits n se 73 N NAT Call Mod oconooccnnnninoncconnos 69 Network Requirements 17 NN ar a 4 O Outgoing Fast Start ee 68 P Password cccccsssceeeseeeeeees 65 78 PBs ni TE 4 12 PLA Riendo 97 99 101 PPROE oa 90 PSTN idad 4 R Healt E is 12 Rear Panel cie 16 Registration Type 70 Restore Dial Plan 77 RTOS Geiner E ENR 12 RTP eienen 4 14 RTP Port BaS8 coooooccconoccninonnnnnss 68 S Scenario it aos
3. If your PC is already configured check with your network administrator before making the following changes e In the Default gateway field enter the TVP 224HR s IP address and click OK Your LAN administrator can advise you of the IP Address they assigned to the TVP 224HR e If the DNS Server fields are empty select Use the following DNS server addresses and enter the DNS address or addresses provided by your ISP then click OK 35 Internet Access To configure your PCs to use the TVP 224HR for Internet access 1 Ensure that the DSL modem Cable modem or other permanent connection is functional 2 Use the following procedure to configure your Browser to access the Internet via the LAN rather than by a Dial up connection For Windows 9x ME 2000 1 Select Start Menu Settings Control Panel Internet Options 2 Select the Connection tab and click the Setup button 3 Select I want to set up my Internet connection manually or I want to connect through a local area network LAN and click Next 4 Select I connect through a local area network LAN and click Next 5 Ensure all of the boxes on the following Local area network Internet Configuration screen are unchecked 6 Check the No option when prompted Do you want to set up an Internet mail account now 7 Click Finish to close the Internet Connection Wizard Setup is now completed For Windows XP 1 Select Start Menu Control Panel Network and In
4. Microsoft VPN PPPoE Configuration If using PPPoE PPP over Ethernet a screen like the following example will be displayed when the PPPoE button is clicked Home Be Internet Access 9 Help TVP 224HR VoIP Gateway Router WAN PPPoE Configuration Enable PPPoE Service name No User Name Password Idle timeout in 0 seconds IPCP fixed IP address A Authentication protocol pap Transmit 0 kbps bandwidth MTU Size gene bytes ok Figure 20 PPPoE Configuration Screen Data PPPoE Screen Connection Enable PPPoE Yes No User Name User Name as assigned by your ISP Password Password as assigned by your ISP Idle timeout in An Internet connection is automatically made when required and seconds disconnected when idle for the time period specified by the Auto disconnect Idle Time out IPCP fixed IP address Default Value 0 0 0 Value should only be changed if advised to do so by Technical Support Authentication Default Value pap Value should only be changed if advised to Protocol do so by Technical Support Transmit Bandwidth Default Value 0 Value should only be changed if advised to do so by Technical Support MTU Size MTU Maximum Transmission Unit value should only be changed if advised to do so by Technical Support Enter a value between 1 and 1500 This device will still auto negotiate with the remote server to set the MTU size The sma
5. CHAPTER 4 PC CONFIGURATION cccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 26 A NR NOS 26 Windows Clients ceoiocicioninnninnosconacioinnscaninncsoncociocnon ono asnnncidiniancondoni ao doLaddasenaDancnU nac visose sssusa 26 TCP IP Settings Overview oeer e e ia dm dad daa E EEEE gree eaten ae 26 Checking TCP IP Settings Windows 9X ME ccsccssesesecsseesseeeeeseeeeeeeeeeeeeeeeeneeneeneenaees 27 Checking TCP IP Settings Windows NT4 0 ccscesseessceseceteceseceeeceecseeeseeeseeeeeeneeeereserees 29 Checking TCP IP Settings Windows 2000 cccecscesscesscesecetecesecesecseecaeeeaeeeeeeneeeeeeeereserees 32 Checking TCP IP Settings Windows XP ccceecceessessceesceseceecesecenecseecaeeeseeeeeeeeeeneeeereeeeees 34 Intemet ACCOSS dis ed AA eens e Apes etal ane A e 36 Macintosh ClientS ooomoncomomomssmsmsmrmmrrs 37 ADAN AAA OO 37 Other Unix Systems cccsssssscsscsscssssscssssessssnsscsssssescsssnessssnesscssscsssssescessnesssssescessesseseesee 37 CHAPTER 5 OPERATION AND STATUS ooccccccccccnnnncccccncccncncnnnnnanananannns 38 Operation isisn scssscvccossrseassessconssaseasocnsecnssensscasensssvaoesesonss soasapsoansunssdsceseseavedsnansdssadenesepadsnseseseonsees 38 System Status Screen scssccssccescesoascssocassesscussssssevssuessescevsssecesoassesesesesassesvssaconsceseseasensoveassosesoasoes 38 CHAPTER 6 INTERNET FEATURES cccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 41 COOVET VIEW secsscsceccsdsescsi
6. Caller on Site A picks up any PBX extension and dials extension 201 TVP Gateway A automatically establishes a connection with TVP Gateway B Port 0 FXO 201 to get the dial tone from PBX on site B After getting dial tone the caller can call any Site B PBX extension 105 TVP 224HR User s Guide Site A TVP Gateway Configuration FXO to FXO PLAR Web Configuration Telnet Console Login to Site A TVP Gateway From Console 1 Logon to the Web Configuration by Enter Username admin opening your browser Enter Password 123 Enter 192 168 0 20 2 You will be prompted for Username and Password Default Username and Password are admin and 123 respectively Windows command prompt Enter telnet 192 168 0 20 Enter Username admin Enter Password 123 or from Web Configuration of Dial Plan atpm req Dial Plan Settings Dial Plan Table Setup atpm aadd 2255222 3 Select Add and Telephone 4 Enter following fields Telephone Number 22 Hunt Group ID 22 Liness 3 12 create an Min Digits 5 address entry for TVP Max Digits 5 Gateway B Strip Length 2 f Append Prefix none 5 Click on OK Dial Plan Settings Dial Plan Table Setup 6 Select Add and HuntGroup atpm hadd 22 2 22 7 Enter following fields a Hunt Group ID 22 b Destination ID 0 22 8 Click on OK Dial Plan Settings Dial Plan Table Setup 9 Select Add and DestinationID atpm dadd 20 h323
7. Consult your network manager to obtain a unique and static IP address for the TVP 224HR the IP subnet mask and default gateway of your network and fill out the work sheet in Appendix D before configuring the gateway Procedures for assigning IP address default gateway and subnet mask is available in Chapter 4 2 6 Hardware Installation Procedures 1 Choose an Installation Site e Select a suitable place on the network to install the TVP 224HR Ensure the TVP 224HR and the DSL Cable modem are powered OFF 2 Connect LAN Cables e Use standard LAN cables to connect PCs to the Switching Hub ports on the TVP 224HR Both 10BaseT and 100BaseT connections can be used simultaneously e Ifrequired you can connect any LAN port to another Hub Any LAN port on the TVP 224HR will automatically function as an Uplink port when required Just connect any LAN port to a normal port on the other hub using a standard LAN cable e If desired connect a PC server to the DMZ port To use multiple servers use a standard LAN cable to connect the DMZ port to a normal port on another hub and connect your servers to the hub PCs connected to the DMZ port are isolated from your LAN 3 Connect WAN Cable e Connect the Broadband modem to the WAN port on the TVP 224HR Use the cable supplied with your Broadband modem If no cable was supplied use a standard LAN cable 4 Power Up e Power on the Broadband modem e Connect one end of the power cord that
8. Note that in this illustration both Internet users are connecting to the same IP Address but using different protocols To Internet users all virtual Servers on your LAN have the same IP Address This IP Address is allocated by your ISP 47 This address should be static rather than dynamic to make it easier for Internet users to connect to your Servers However you can use the DDNS Dynamic DNS feature to allow users to connect to your Virtual Servers using a URL instead of an IP Address Virtual Servers Screen The Virtual Servers screen is reached by the Virtual Servers link under the Router Configuration menu An example screen is shown below TVP 224HR VoIP Gateway Router Virtual Server Setup External Port Internal IP 1 TCP y TCP EN TCP TCP TCP TCP y TCP y TCP Dial Plan Line Settin OA NIOU A UOUN TCP TCP o Figure 24 Virtual Servers Screen Data Virtual Servers Screen Virtual Server Data Checkbox Use this to Enable or Disable this Special Application as required Protocol Type Select the protocol TCP or UDP used when you receive data from the special application or service Note Some applications use different protocols for outgoing and incoming data External Port Enter the port number used by the virtual server Internal IP Enter the IP Address of
9. TCP e 10 TCP y TCP y Data Special Applications Screen Figure 21 Special Applications Screen Checkbox Use this to Enable or Disable this Special Application as required Description Enter a descriptive name to identify this Special Application Incoming Type Select the protocol TCP or UDP used when you receive data from Ports No the special application or service Note Some applications use different protocols for outgoing and incoming data From Enter the beginning of the range of port numbers used by the application server for data you receive If the application uses a single port number enter it in both the From and to fields To Enter the end of the range of port numbers used by the application server for data you receive Microsoft VPN Outgoing Type Select the protocol TCP or UDP used when you send data to the Ports remote system or service From Enter the beginning of the range of port numbers used by the application server for data you send to it Ifthe application uses a single port number enter it in both the From and To fields To Enter the end of the range of port numbers used by the application server for data you send to it If the application uses a single port number enter it in both the From and To fields Using a Special Application e Configure the Special Applications screen as required e On your PC use the application normally Remember that only on
10. ossnoss sososers ssns osos 79 Password See Chapter 7 er a a a a a s ar e aa aae aie asise 79 Telnet ACCESS il a nee hentia wa area a eee 80 Interface Peinados actos 80 9 11 Channel Status csscsscssrcssssscssscscscssosssosesoscsessonsssnsssssvescnesssesseesseessesssosssonsoessoes 80 9 12 Help icsscscsccsecsseasseesentondcsensonsesesdessecvossesededsesinsscbensueesdassacscendsadens ostssensousneusdendoswassueasonsees 80 CHAPTER TO niea e a iea Eaa E 81 MAKING CALLS WITH TVP 224HR oonoccccccccnnnnnnonnnnnnnnnnnnnnnnnnnnnannnnnnnas 81 10 1 Configuration Examples cscscssssssssssscssscssscssscsescscssccsscsssssscsssssesssssesessseeseeees 81 Default Dial Plan ic daa Add 81 10 2 Making a call with TVP 224HR FXS Pott sscsscssssscsssnsssesssscescsssescessnessesneeees 82 10 3 Making a call with TVP 224HR FXO Port sessesesesecceeerorsesesecoesosorsesesecoesoroeseseceeoeeeee 83 10 4 Web Browser Sample Dial Plam sccssscsssssssscsssssssssssscescsssescessnessssscssessessesees 83 10 5 Making a call between Gateway A and Gateway B onooccoonccnncconcnonononononnarocaronononos 90 Case 1 Gateway Phone to Gateway PhoNS ooooonocinoniocnonnconnconcconcnnnonnnono nono nono ronnonnncnnncn nro 90 Case 2 Gateway Phone to PSTN Phone ooooooococcnnoconoccoonconoconoconono nooo ncnnnonnnonnnonnnonnrnnnrnnncnnnnns 91 Case 3 PSTN Phone to Gateway Phone ccccccceesseesceseceseceseceseeeecaeecaeeeseeee
11. use the PC Database option on the Other menu No of DHCP clients This shows the possible number of Clients as chosen Starting client addr Firmware Version TVP 224HR Version The starting IP address to be assigned by the DHCP Server This displays the firmware version of the TVP 224HR Boot Version The current boot version 39 H 323 Settings Result h323 display_name Customer h323 h245_term_type 60 h323 rtp_port_base 30000 h323 out_fast_start off h323 in_fast_start off h323 h245_tunneling off h323 cisco_t38 on h323 callSignalPort 1720 h323 nat_call on h323 call_name h323 local_alert off h323 default_dtmf H323 Y2 Signal No Alternate IP Defined h323 gk_mode off h323 h245_timeout 30000 h323 term_id h323 gk_fail 40 ore Chapter 6 Internet Features This Chapter explains when and how to use the TVP 224HR s Internet Features Overview The following advanced features are provided e Internet Access Configuration e DMZ e Packet filter e Dynamic DNS e Special Applications e Virtual Servers e Port Forwarding e Voice QoS Internet Access Configuration The Internet Access menu has three submenus providing for three different types of internet connection Fixed IP DHCP and PPPoE The first is Fixed IP as shown below TVP 224HR VoIP Gateway Router br Home AO Fixed IP Network Settings B Fixed IP B DHCP Client IP Addres
12. 1 3 Package NOA O 14 1 4 Front Pane A NN 14 LED Indicators Lotta dae ld a da tard dla lili 15 Reset Buttons nt Seat Ate a da dro de dect loro de a dond 15 1 5 Rear Panel OEE EE EE N E ENE 15 WAN FEAN Console Ports iii cia 16 A e a ee ea a a o N E aoa 16 CHAPTER A E E E EE S 17 INSTALLING THE TVP 224HRo oonccccnccconnoccncanccanancnnnannonanononanonananenanana 17 2 1 Network Requirements seseossesessessesoosseseosoesessossesoessesoesoesessossesoossesoesoesessossesssssesoesse 17 2 2 Installing the TVP 224HR cscscscsssssssssssscssssscnscsssnessssnessesncssessessessessnssssssesseees 17 2 3 Connecting to the telephony deviceS ooooommsmss 17 2 4 Connecting to the LAN Network ssesessessescosoesessossesoessesoosoesessoesesoossesoosoesessossessssssso 17 2 5 Assigning an IP address to the TVP 224HR sesessssesorsesesecccsososesesecoesosorsesesocoesosoesese 18 2 6 Hardware Installation ProcedureSs ssseesscsecssoceessececssccsssseessocecsseceessecessseossooeessoceee 18 CHAPTER A TT Saai 20 ROUTER SETUP oa 20 A A O ON 20 Configuration Program cssccsssscssssscsssssssessssnsssesssscesesssessessnessssnescessssssesenssssssessessesees 21 E aches eee 21 Home S CLES eeyan cere san reed ded aaa wasn eee gcse cee an Paved an ceca E AO A EE eA 22 LAN Configuration sccccssccsesscsscsscescsssncsscsnescesscssescessnsssssnessesecssesssssossessnessesncssessessoseeses 24 DHOP renger sui an asa ab ieee et 25
13. 192 168 0 55 10 Enter the following fields a Destination ID 22 b Hostname or IP address atpm done 192 168 0 55 atpm store c Click on OK Dial Plan Settings Dial in PLAR CID 11 Enter 22201 in the PLAR Address Field 12 Click on OK Dial Plan Settings Store Dial Plan 13 Click on Yes ono Ff set tcid 0 dial_in plar 22201 config activate config store Lines 11 13 setup the hotline PLAR from TVP Gateway A to TVP Gateway B 106 TVP 224HR User s Guide Chapter 11 Telephony Connections This section discusses the special connection consideration for various environments and situations where you can use the VoIP Gateway 11 1 Port Configuration VoIP Gateway supports FXS and FXO ports FXS Foreign Exchange Station FXS provides power and ringing signals to its interfacing equipment It is not intended for connection to the Public Switched Telephone Network It is a station loop start operation that provides a connection to 1 A standard single line analog telephone system 2 The line circuit of a key telephone system 3 A loop start trunk circuit of a Private Branch Exchange PBX that normally connects to incoming Central Office circuits FXO Foreign Exchange Office FXO recognizes signals and draws current to indicate an active state It is a trunk loop start operation that emulates a single line telephone to 1 Central Office lines 2 PBX station There are three basic envir
14. 224HR User s Guide Remote Destinations Each remote TVP 224HR to be reached must be assigned a unique destination ID Obtain the IP addresses of the TVP 224HR at remote sites and fill out the worksheet for remote destinations by designating each remote TVP 224HR a unique destination ID then use the CLI command atpm dadd dest_id h323 ip_addr ip_port for each entry in the worksheet to add it to the destination table The dest_id in the command corresponds to the Destination ID in the worksheet the ip_addr corresponds to the Port the optional ip_port corresponds to the IP port You may alternatively use the web browser to add remote destinations to the destination table IP address IP port Mode Destination ID optional H323 H323 H323 H323 H323 H323 H323 H323 H323 H323 H323 H323 H323 H323 H323 H323 123 TVP 224HR User s Guide ATPM Hunt Group Table Several destinations may be grouped together to form a hunt group When an incoming phone number matches the phone number of the hunt group the TVP 224HR attempts to terminate the call at each of the destinations in the hunt group one at a time until a call is successfully completed Plan how destinations are to be grouped and fill out the hunt table worksheet then use the CLI command atpm hadd hunt_group_id hunt_type dest_id_ for each entry in the worksheet to add it to the hunt group table The hunt_grou
15. 8 Select Add and Telephone 9 Enter following fields a Telephone Number 11 b Hunt Group ID 11 c Min Digits 2 d Max Digits 5 e Strip Length 2 f Append Prefix none 10 Click on OK Dial Plan Settings Dialplan Table Setup 11 Select Add and HuntGroup 12 Enter following fields a Hunt Group ID 11 b Destination ID 11 13 Click on OK Dial Plan Settings Dialplan Table Setup 14 Select Add and DestinationID 15 Enter the following fields c Destination ID 11 d Hostname or IP address tvp1 dyndns org e Click on Ok Dial Plan Settings Store Dial Plan 16 Click on Store TVP 224HR User s Guide atpm req atpm aadd 11 25 112 atpm hadd 11 2 11 atpm dadd 11 dns tvp1 dyndns org atpm done atpm store 99 TVP 224HR User s Guide 10 8 Dial in PLAR Hotline TVP 224HR TVP 224HR Trendware VoIP Gateways are capable of automatically calling or forwarding an incoming call from the Internet or PSTN line onward to another remote destination The following three examples illustrate these topographies 1 FXS to FXO PLAR 2 FXO to FXS PLAR 3 FXO to FXO PLAR Case 5 PLAR Hotline FXO to FXS example INTERNET TVP Gateway A TVP Gateway B 192 woo E 192 168 0 55 oo A mm J FXS 203 Local number for example 8888 1234 This could be a call placed from any outside PSTN number 100 TVP 224HR User s Guide
16. 83 Store Dial Plan 75 76 Strip Length ooooonncnn inmmmmm 73 System Status ooooocnoocccooncconcconnnos 67 T TED Ada 4 Technical Specifications 107 Telnet ACCESS oocococccoconionnconnncnn 79 Terminal ID oooooonncccnocncconnnonnccnns 70 Terminal Type oooooncconnnincnnnnnocnnos 68 Termination Digit 78 TER io stints 4 A A Pas EN de 4 61 Time To Liens bis 70 IN tic 4 Total Time ici 78 Troubleshooting 105 U UD ii ts 4 User name iii 65 UND aa ea renee eee 4 127 TVP 224HR User s Guide vV MAD o 4 12 14 VOIP ina 12 14 W WAN autre e 4 Worksheet ooooooccnnonoccnononnconon 115 TVP 224HR User s Guide Limited Warranty TRENDware warrants its products against defects in material and workmanship under normal use and service for the following lengths of time from the date of purchase TVP 224HR 5 Years Warranty If a product does not operate as warranted above during the applicable warranty period TRENDware shall at its option and expense repair the defective product or part deliver to customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the defective product All products that are replaced will become the property of TRENDware Replacement products may be new or reconditioned TRENDware shall not be responsible for any software firmware information or memory data of customer c
17. Case Scenario Outside PSTN caller near Site A wants calls automatically forwarded to extension 203 on Site B Definition PLAR Private Line Auto Ring Bat phone Hotline which allows you to pick up phone and automatically be connected to pre determined remote destination Solution Set up hotline PLAR on TVP Gateway on Site A to TVP Gateway on Site B This uses existing default local dial plan with the addition of a remote destination zone number Usage PSTN Caller near Site A picks up phone 8888 1234 and dials PSTN number 9999 2222 which is connected to Site A TVP Gateway FXO port 201 TVP Gateway A will automatically forward the call via internet to TVP Gateway B FXS phone 203 101 TVP 224HR User s Guide Site A TVP Gateway configuration FXO to FXS PLAR Web Configuration Telnet Console Login in to Site A TVP Gateway Logon to the Web Configuration by opening your browser 1 Enter Wan IP xxx xxx xxx Or if you are on the LAN 192 168 0 20 2 You will be prompted for Username and Password Default Username and Password are admin and 123 respectively Web Configuration of Dial Plan Dial Plan Settings Dial Plan Table Setup 3 Select Add and Telephone 4 Enter following fields a Telephone Number 22 b Hunt Group ID 22 c Min Digits 5 d Max Digits 5 e Strip Length 2 f Append Prefix none S Click on OK Dial Plan Settings Dial Plan Table Setup 6 Select
18. Data Dyn DNS On Off User Name Enter your Username for the DDNS Service Password Key Enter your current password for the DDNS Service Domain Name Enter the domain hostname name registered at www dyndns org Hostname For instance if you registered johnsmith dyndns org please enter 46 Microsoft VPN johnsmith DDNS Status This message is returned by the DDNS Server Normally this message should be something like Update successful or IP address updated If the message indicates some problem you need to connect to the DDNS Service provider and correct this problem Virtual Servers Port Forwarding This feature allows you to make Servers on your LAN accessible to Internet users Normally Internet users would not be able to access a server on your LAN because e Your Server does not have a valid external IP Address e Attempts to connect to devices on your LAN are blocked by the firewall in this device The Virtual Server feature solves these problems and allows Internet users to connect to your servers as illustrated below E 192 168 0 1 m WEB Server LAN IP Address FTP Server 192 168 0 10 192 168 0 20 TVP 224HR 192 168 0 1 203 70 212 52 Internet IP Address bb a c Internet _ oe f j ho a Remote PC Remote PC Using Web Server Using FTP Server htip 1 203 70 212 52 Mip 1 203 70 212 52 Figure 23 Virtual Servers IP Address seen by Internet Users
19. Power is supplied to the gateway Data is being transferred on the LAN The gateway is connected to LAN at 100Mb s The gateway is connected to LAN at 10Mb s The gateway is connected to WAN Data is being transferred on the WAN On On Off The line is idle On The line is being used Blinking The line is ringing Reset Button There is a recessed push button located next to the SYSTEM LED This button allows you to reset the TVP 224HR or force the TVP 224HR to enter firmware upgrade mode To reset the gateway push a small stiff object into the hole until the SYSTEM LED stops blinking then release the button Powering on the gateway while pressing down the button for 5 seconds forces the TVP 224HR to enter download mode 1 5 Rear Panel The rear panel of the TVP 224HR has four analog telephony ports two FXO and two FXS ports offering flexible telephony interface usage The FXS telephony interface ports may be connected to Subscriber Equipment such as Telephones Fax Machines Cordless Phones and Modems FXO ports can be connected to PBX and local phone company Central Office CO lines In addition to analog telephony interface ports there is a power jack for power adapter connection on the rear panel 15 4 port TVP 224HR Rear Panel WAN LAN Console Ports The TVP 224HR is equipped with 1 WAN and 4 LAN Ethernet interfaces with 10 100 Mbps auto negotiation auto MDIX capability The Ethernet p
20. Settings a Administration ok Help Data Voice QoS Screen Voice QoS Data On Off Use this to Enable or Disable Voice QoS functionality as required Assured Bandwidth Enter the amount of bandwidth you would like to reserve for VoIP for Voice packets To determine how much bandwidth you will require multiply the number of potential simultaneous connections channels ports by the current codec you are implementing G 711 PCM 64kbps Packet Header information 80 5 Kbps G 723 1A 5 3 6 3kbps Packet Header information 10kbps 2 kbps G 729AB 8kbps 12 4 kbps Default codec is G 729AB Therefore if all FXO and FXS ports are being used 4 Ports multiplied by the default compression codec G 729AB at 16kbps would yield roughly 72kbps 49 Maximum Uplink In the Field you will first have to find your ISP s speed in your Bandwidth allowed contract or on the ISP s webpage kbits sec The valent Bas e values for speed are usually given in kilo Bits per second kb s as are the values to be entered into TVP 224HR If you are given you Maximum Uplink Bandwidth in KB s To convert to kilo Bytes simply multiply the kilo Bytes by a value of 8 Example Maximum Downstream 96kB s x 8 768kb s Maximum Upstream 16kB S x 8 128kb s IP ToS Buttons OK Click on this to save data entered 50 Chapter 7 Administration This Chapter explains Password setup remote Administration via T
21. User s Guide h323 in_fast start Off h323 h245_ tunneling Off h323 cisco_t38 Off h323 callSignalPort 1720 h323 call_name None h323 local_alert Off h323 default_dtmf H323 V2 Signal h323 gk mode Off h323 h245_ timeout 30000 h323 term_id None Voice codec Preferred voice codec G 723 6 3kbps Telephony PCM codec receiver gain for FXO ports 1 dB 121 TVP 224HR User s Guide Appendix F Worksheets IP Parameters Consult your network manager to obtain a static IP address for the TVP 224HR and the information about the IP subnet mask and the default gateway for your network Fill out the following work sheet before configuring the TVP 224HR IP address IP subnet mask Default gateway ATPM Destination Table Local Destinations Each telephony port of the TVP 224HR must be assigned a unique destination ID Fill out the worksheet for local destinations by designating each port a unique destination ID then use the CLI command atpm dadd dest_id port port for each entry in the worksheet to add it to the destination table The dest_id in the command corresponds to the Destination ID in the worksheet while the port corresponds to the Port You may alternatively use the web browser to add local destinations to the destination table Port Mode Destination ID 0 port 1 port 2 port 3 port 122 TVP
22. admin all lower case Password is 123 Both admin and 123 are default strings from factory For security reasons please change and memorize the new password after this first setup 4 Click OK The main screen will appear as below 65 TVP 224HR User s Guide Address 4 http 192 168 0 1 Hpo My File Edit View Favorites Tools Help Q x A CD Osea She Favorites Q reas O Aria BUZI System Status WAN Interface Parameters MAC address 00 50 2d 00 f5 09 Dynamic DNS Disabled Access Mode Fixed IP IP address 60 248 111 217 Subnet mask 255 255 255 0 Default gateway 60 248 111 254 Pri DNS server 168 95 1 1 Sec DNS server 0 0 0 0 LAN Interface Parameters MAC Address DO 50 2d 00 f5 08 IP address 192 168 0 1 Subnet mask 255 255 255 0 DHCP server Enabled No of DHCP clients 30 Starting client addr 192 168 0 10 Firmware Version TVP 224HR Version 2 01 005 O9New 0418 Boot Load Version 1 01 DSP Image Version 8 1 2 1 TSG Version R8 0 Gateway Build 4 Main Menu Function Briefings Home View System Status H 323 Configuration Set H 323 Parameters Dial Plan Settings Links to dial plan setting entry store clear restore pages You should complete the dial Plan work sheets before working in this menu Line Settings Set Line Settings including Channel Status Codec Selection Common Parameters Channel Parameters and Telephony Ports Administration
23. came with the TVP 224HR to the power jack on the rear panel e Connect the other end of the power cord to an AC power outlet e The TVP 224HR will execute memory and application code testing automatically e Use only the power adapter provided Using a different one may cause hardware damage Setup 5 Check the LEDs e The Power LED should be ON e The Systems LED should be blinking e For each LAN PC connection the LAN Link Act LED should be ON provided the PC is also ON e The WAN LED should be ON e For each telephony device connection the Line LED should be ON provided the device is plugged in and receiver is off hook 19 Chapter 3 Router Setup This Chapter provides Setup details of the TVP 224HR Overview This chapter describes the setup procedure for e Internet Access e LAN configuration PCs on your local LAN may also require configuration For details see Chapter 4 PC Configuration Other configuration may also be required depending on which features and functions of the TVP 224HR you wish to use Use the table below to locate detailed instructions for the required functions To Do this Refer to Configure PCs on your LAN Chapter 4 PC Configuration Check TVP 224HR operation and Status Chapter 5 Operation and Status Use any of the following Internet features Chapter 6 Internet Access Configuration Internet Features Dynamic DNS Domain Name Server Special Appl
24. enter HTTPS followed by the Internet IP Address of the TVP 224HR If the port number is not 80 the port number is also required After the IP Address enter followed by the port number e g HTTPS 123 123 123 123 8080 This example assumes the WAN IP Address is 123 123 123 123 and the port number is 8080 Upgrade Firmware Use this screen to upgrade your TVP 224HR s firmware e You must download the required firmware file and store it on a TFTP Server e During the upgrade process all existing Internet connections will be terminated e The upgrade process must NOT be interrupted TVP 224HR VoIP Gateway Router oa EEES Firmware Update Settings TFTP Server IP Ed Line Settings FIA a Firmware Name B Password B Remote Management Update Caution Please do not interupt the firmware update process Disruption of the update process could result in permanent damage to your TVP 224HR Gateway Please refrain from performing other tasks during this process Figure 28 Upgrade Firmware Screen Data Upgrade Firmware Screen Upgrade Firmware Upgrade File Click the Browse button and browse to the location on your TFTP Server where you stored the firmware upgrade file Select this file TFTP Server IP Enter the IP address of the TFTP Server 54 TVP 224HR User s Guide Update Click this button to start the Firmware upgrade Note than any users accessing the Internet via the TVP 224HR will
25. modular jacks Line impedance 600 Q 900 Q Complex line impedance Insertion loss 2 dB nominal Frequency response 300 Hz 3400 Hz 2 dB w r t 1004 Hz Return loss gt 18 dB Input level adjustment 6 dB to 6 dB Output attenuation O dB to 13 dB Longitudinal balance gt 45 dB Loop current 25 mA nominal Ring voltage 40 Vrms nominal Ringing tone 16 67 Hz 20 Hz default 25 Hz or 50 Hz Disconnect detection Loop current 112 TVP 224HR User s Guide Console Port The console port uses a DB 9 RS 232 connector The supplied straight through RS 232 cable connects the console port of the TVP 224HR to a console PC or terminal Pin assignment for the port is described in the following table DB 9 pin Signal 1 Not connected TxD RxD Not connected Ground ot connected Not connected Not connected Oo co aj a Wm al Ww bw Z Not connected LAN Port The 10 100 LAN port use standard RJ 45 connector and Ethernet pin assignment The following diagram and table show the pin assignment on the port connector When connecting the LAN port to switches or repeaters you must use a straight through cable RJ45 pin Signal 1 RxD 1 RxD TxD Not connected Not connected TxD Not connected CO NT AIA AJ UJ N Not connected
26. pop up menu 3 Select Using DHCP Server from the Configure pop up menu The DHCP Client ID field can be left blank Close the TCP IP panel saving your settings gt Note If using manually assigned IP addresses instead of DHOP the required changes are e Set the Router Address field to the TVP 224HR s IP Address e Ensure your DNS settings are correct Linux Clients To access the Internet via the TVP 224HR it is only necessary to set the TVP 224HR as the Gateway Ensure you are logged in as root before attempting any changes Fixed IP Address By default most Unix installations use a fixed IP Address If you wish to continue using a fixed IP Address make the following changes to your configuration e Set your Default Gateway to the IP Address of the TVP 224HR e Ensure your DNS Name server settings are correct To act as a DHCP Client recommended The procedure below may vary according to your version of Linux and X windows shell Start your X Windows client Select Control Panel Network Select the Interface entry for your Network card Normally this will be called eth0 Click the Edit button set the protocol to DHCP and save this data To apply your changes Ai 2 A e Use the Deactivate and Activate buttons if available e OR restart your system Other Unix Systems To access the Internet via the TVP 224HR e Ensure the Gateway field for your network card is set to the
27. sure to Store the Dial Plan from working memory DRAM to Flash Memory Non Volatile Storage Storing to Non Volatile Storage ensures that you have saved the dial plan which can then be restored on request Note The Dial Plan in the Non Volatile Storage is not the working Dial Plan If the Gateway is turned off for what ever reason the Dial Plan from Non Volatile Storage is copied into the Flash Working memory and processes phone calls accordingly 9 6 Clear Dial Plan Clear Dial Plan Will clear the Dial Plan from DRAM Working memory 77 TVP 224HR User s Guide DRAM Everytime you make an entry into the Address Table Hunt Group Table or Destination ID table you have to Click on Complete This only saves the plan to the working memory DRAM If there was a power outage or the TVP 224HR was unplugged or a system crash for what ever reason the Dial Plan in working memory DRAM will be lost 9 7 Restore Dial Plan Restore Dial Plan Will retrieve the Dial Plan from Flash Memory Non Volatile Storage but erase the dial plan currently in DRAM Working memory Note To ensure your new settings are actually accepted please check the configuration page carefully after you submit the new settings Ifthe new settings are not present it probably conflicts with the old settings or there is not enough space to store your settings 9 8 Line Settings Channel Status View all settings made to each Channel port Simply Se
28. the range used by the DHCP Server Using another DHCP Server You can only use one 1 DHCP Server per LAN segment If you wish to use another DHCP Server rather than the TVP 224HR s the following procedure is required 1 Disable the DHCP Server feature in the TVP 224HR Disable the DHCP by entering 0 in the number of clients field 2 Configure the DHCP Server to provide the TVP 224HR s IP Address as the Default Gateway To Configure your PCs to use DHCP This is the default setting for TCP IP under Windows 95 98 ME See Chapter 4 Client Configuration for the procedure to check these settings 25 Chapter 4 PC Configuration This Chapter details the PC Configuration required on the local Internal LAN Overview For each PC the following may need to be configured e TCP IP network settings e Internet Access configuration Windows Clients This section describes how to configure Windows clients for Internet access via the TVP 224HR The first step is to check the PC s TCP IP settings The TVP 224HR uses the TCP IP network protocol for all functions so it is essential that the TCP IP protocol be installed and configured on each PC TCP IP Settings Overview If using the default TVP 224HR settings and the default Windows TCP IP settings no changes need to be made e By default the TVP 224HR will act as a DHCP Server automatically providing a suitable IP Address and related informati
29. the virtual server The PC must be running the appropriate Server software Internal Port Enter the port number used by the virtual server Connecting to the Virtual Servers Once configured anyone on the Internet can connect to your Virtual Servers They must use the Internet IP Address the IP Address allocated to you by your ISP e g http 203 70 212 52 ftp 203 70 212 52 48 Microsoft VPN It is more convenient if you are using a Fixed IP Address from your ISP rather than Dynamic However you can use the Dynamic DNS feature described in the following section to allow users to connect to your Virtual Servers using a URL rather than an IP Address QoS is a popular feature that guarantees better service to selected traffic on a network The goal in configuring QoS is to give priority and attention to certain devices or services so that they can use the maximum available throughput and speed available on a certain network when it is needed Voice QoS Screen The Voice QoS screen is reached by the Voice QoS link under the Router Configuration menu An example screen is shown below TVP 224HR VoIP Gateway Router Home Voice QoS Settings Gg Internet Access E pw Router C B LAN B QoS B DMZ Enable Voice QoS Off Assured Bandwidth for Voice 24 kbits sec Maximun Uplink Bandwidth Allowed kbits sec BA koits sec 1 IP TOS B8 2 Hex digit byte value Dial Plan Settings Line
30. to Site A local PSTN Solution Set up hotline PLAR on TVP Gateway on Site B to TVP Gateway on Site A This uses existing default local dial plan with the addition of a remote destination zone number Definition PLAR Private Line Auto Ring Bat phone Hotline which allows you to pick up phone and automatically be connected to pre determined remote destination Usage Caller on Site B picks up FXS 203 phone and TVP Gateway B automatically connects to TVP Gateway A FXO 201 which is connected to PSTN line 9999 2222 Caller will hear PSTN dial tone on Site A and can then call any number on local PSTN 103 TVP 224HR User s Guide Site B TVP Gateway Configuration FXS to FXO PLAR Web Configuration Telnet Console Login to Site A TVP Gateway 1 Logon to the Web Configuration by opening your browser 2 Enter 192 168 0 55 3 You will be prompted for Username and Password Default Username and Password are admin and 123 respectively Web Configuration of Dial Plan Dial Plan Settings Dial Plan Table Setup 4 Select Add and Telephone 5 Enter following fields Telephone Number 11 Hunt Group ID 11 Min Digits 5 Max Digits 5 Strip Length 2 f Append Prefix none 6 Click on OK Dial Plan Settings Dial Plan Table Setup 7 Select Add and HuntGroup 8 Enter following fields a Hunt Group ID 11 b Destination ID 11 9 Click on OK Dial Plan Settings Dial Plan Table Set
31. 2 10 13 0 None Code are sent to to remote GW B GW B FXO External PBX to PSTN Hunt Group ID Hunt Type of Dest ID s Dest ID s 2 2 1 2 3 2 1 3 4 2 1 4 5 2 1 4 6 2 1 4 7 2 1 4 88 TVP 224HR User s Guide 22 2 1 22 Gateway A Destination Table Dest ID Mode Destination 2 Local Port 2 3 Local Port 3 4 Local Port 0 22 Remote Dest 192 168 1 55 1720 TCP The above destination table has both local destinations and remote destinations When the gateways are taken out of this initial testing environment and implemented in the field the internet access settings will have to be updated In addition the above remote destination IP will have to be updated to the field IP address Gateway B Telephone Number Table Comment Phone Hunt Min Max Prefix Prefix Function Group ID Digits Digits strip Address 4 1 1 1 None Dialing 203 calls phone on Port 2 Dialing 204 calls phone on Port 2 Dialing 9 from local Assumes that phone on FXS Port Telephone line is gets you a dial tone attached to Port 0 on FXO Port 0 for Line 1 outside line 02 is stripped and Assumes that the remaining 8 to 11 Telephone line is digits 3 Digit US attached to Port 0 Area Code are Line 1 dialed out on Port 0 to PSTN Remote Zone used to make calls to remote GW A F
32. 2400 47624 50000 50100 Half Life 27015 Heretic II 28910 Hexen II Each computer must use a 26900 1 for each different port number Add 1 player for each player starting with 26900 KALI Each computer must use a 2213 1 for each different port number Add 1 player for each player starting with 2213 6666 MSN Game Zone 6667 28800 29000 MSN Game Zone DX 2300 2400 47624 Myth 3453 Need for Speed 9442 Need for Speed 3 1030 Outlaws 5310 59 TVP 224HR User s Guide Quake III Each computer uses a 27660 1 for each different port number Add 1 player for each player starting with 27660 Rainbow Six 2346 Rogue Spear 2346 StarCraft 6112 Tiberian Sun 1140 1234 4000 Ultima 5001 5010 Game 7775 7777 Login 8888 9999 Patch 8800 8900 Messenger 7875 Monitor Unreal Tournament Need to modify the UWeb WebServer section of the server ini file Set ListenPort to 8080 Set ServerName to the Public IP of your router 7777 game 7778 server 7779 7783 UdpLink 27900 server query 8080 UT Server Admin XBox There are known problems with XBox Live Network see Cannot Log On XBox with Router 88 3074 XBox incorrectly says this is unnecessary in all cases Note PCs not assigned to any group will be in the Default group PCs deleted from any other Group will be added to the Defau
33. A OEA 67 32 3 Para eE S a r e E a a a 68 CEI A 0E tt NE E e EEE E 69 Aliase S an E E ho 71 9 3 Dial Plan Settings occoccoonooonnnononnoononnconconocononncnncononnonncononononococconcnnooncn nono rococorcononccononoss 73 Dial Plan SUP A A RA OR i 73 Telephone Number Table 20 50 2 cscccc cseccacscctccedeuesceacasdiceudestecsacesevcsiceleecoteeddessrdedtessaenieotsasetes 73 Hunt Group Tale tdci 74 Destination ID Table A 75 9 4 Dial in PLAR CUD sevecscscccusssccacsseccccoosorsesensesteesesersnvssionseccecpssosessecseccesevsceonsacteseaseusrsaes 76 Dial in PLAR Considerations and Limitations c cccecccesceseceseeeseeneecaeeeeeeeseeeeeenseeereeseees 77 9 5 Store Dial Platnss cs cscssessesescassexcosesesveesssesssosssnedoasdsoadeonssesdesssencdensossovescessevessoseosedoeassds 77 9 6 Clear Dial Plan AAA O 77 9 7 Restore Dial Plan sicccccssisscesscesseessesssecssvsnssesovssconssanssuosunsoiecesaseavedss necsansonsaepaoseassesoonsens 78 99 A NOE 78 Channel Stats ita eee 78 Codec Selection a is it 78 COMMON Parameter S escort riada 78 Total Time iii aia edi 79 First Dig Weart T iting EEE A AT ET T 79 Inter Digit Wait E a EE aaa ae A E E a aaa e E Ea 79 Termination Dist dd ae a ds ROU 79 9 9 Channel Parametter ssssscssscssscecscecccsceseccscssscssscsesssesscsesesecssecsseeseessoessessessseseees 79 9 10 Administration sssssssssssssssssssessesissoesssosssosossosssssosssessssssoesss vossos essor s
34. Add and HuntGroup 7 Enter following fields a Hunt Group ID 22 b Destination ID 0 22 8 Click on OK Dial Plan Settings Dial Plan Table Setup 9 Select Add and DestinationID 10 Enter the following fields a Destination ID 22 b Hostname or IP address 192 168 0 55 c Click on OK Dial Plan Settings Dial in PLAR CID 11 Enter 22203 into the PLAR Addr Field 12 Click on OK Dial Plan Settings Store Dial Plan 13 Click on Yes From Console Enter Username admin Enter Password 123 or Windows command prompt Enter telnet xxx xxx XxX XXX Enter Username admin Enter Password 123 atpm req atpm aadd 22 5 5 22 2 Lines 3 10 creates a zone number a number that tells the ATPM to forward to a remote destination address entry in TVP GW A for TVP GW B atpm hadd 22 2 22 atpm dadd 22 h323 192 168 0 55 atpm done atpm store set tcid 0 dial_in plar 22203 config activate onfig store 102 Lines 11 13 Setup the hotline PLAR from TVP Gateway A to TVP Gateway B TVP 224HR User s Guide Case 6 PLAR Hotline FXS to FXO example INTERNET TVP Gateway A TVP Gateway B 192 168 020 ya G 92 168 055 FXO 201 a Psty J FXS 203 J Local number for example 8888 1234 Caller on Site B could dial any Site A local PSTN number Case Scenario Caller on Site B FXS 203 wants to be able to pick up phone and immediately have dial tone
35. CP Server Enter telnet 192 168 0 1 If you are trying to access the TVP Or from a remote computer 224HR from a PC in the same segment as the TVP 224HR LAN Open your browser and enter Enter telnet tvp1 dyndns org Enter Username admin Enter 123 1 Enter 192 168 0 1 If you would like to access the TVP 221H from the WAN side from a remote PC with Internet Access You would then continue as below 2 Enter tvp2 dyndns org You will be prompted for Username and Password Default Username and Password are admin and 123 respectively You could then continue as below Web Configuration of Dial Plan Dial Plan Settings Dial plan Table atpm req Setup atpm aadd 22 2 5 222 7 Select Add and Telephone 8 Enter following fields Telephone Number 22 Hunt Group ID 22 Min Digits 2 Max Digits 5 Strip Length 2 f Append Prefix none 9 Click on OK 2207p Dial Plan Settings Dial plan Table atpm hadd 22 2 22 Setup 10 Select Add and HuntGroup 96 TVP 224HR User s Guide 11 Enter following fields a Hunt Group ID 22 b Destination ID 0 22 12 Click on OK Dial Plan Settings Dial plan Table atpm dadd 22 dns tvp2 dyndns org Setup 13 Select Add and DestinationID 14 Enter the following fields a Destination ID 22 b Hostname or IP address tvp2 dyndns org Cc
36. Click on OK Dial Plan Settings Store Dial Plan atpm done 15 Click on Yes atpm store TVP 221HTVP 224HR configuration cable connection on site B Web Configuration Telnet Console Local from a PC in same Segment Console Open your browser Connect RS 232 to TVP 224HR 1 Enter 192 168 0 1 and PC 2 You will be prompted for Open Hyper Terminal Username and Password Input ias Default Username and ia di parameters Password are admin and 123 Baud rate 19 200 respectively Number of data bit 8 Parity check None Login Number of stop bit 1 From the Logon to the Web Flow control None Configuration by opening your browser 24 Enter 192 168 0 1 Enter 123 25 You will be prompted for Username and Password 97 Default Username and Password are admin and 123 respectively Web Configuration of Internet Access Internet Access DHCP Client 3 Select Yes 4 Click on Save Router Configuration Dynamic DNS 5 Select Enable 6 Enter Server Name Host Name User Name Password 7 Click on Save Once Internet Access is setup you could choose to reboot the TVP 224HR and then use a PC in the same segment and with a web browser access the TVP 224HR If using the Router s DHCP Server make sure the routers DHCP Server is on and that the configuring PC is DHCP Client enabled If you would like your PC to have a Fixed IP Make sure t
37. DTMF tone is so called DTMF relay The TVP 224HR handles DTMF relay per H 323 specifications Certain third party VoIP devices may handle DTMF relay per IMTC standard For the TVP 224HR to interoperate with those VoIP devices users need to specify which remote VoIP devices uses IMTC conforming DTMF relay technique Refer to CLI command Error Reference source not found on Chapter 8 for detailed information on how to select DTMF relay mode 8 7 Voice Codecs Voice codecs supported by the TVP 224HR include G 711 G 723 1 5 3kbps G 723 1 6 3kbps and G 729 AB When setting up a call two VoIP Gateways automatically negotiate with each other until an agreement on codec is determined 64 TVP 224HR User s Guide Chapter 9 Configuring VolP from a Web Browser This chapter explains procedures for configuring the TVP 224HR from a web browser 9 1 HTTP setting mode This section describes the processes for setting up the VoIP Gateway once it has been installed Java enabled browsers including Microsoft Explorer version 4 or higher or Navigator version 4 5 or higher can be used in this section to view and change parameters In the Address box enter the following 1 http 192 168 0 1 This is the default IP in the gateway from factory 2 Press enter to confirm and you should find the screen below Connect to 192 168 0 1 index htm User name E admin Password rr Remember my password 3 The User name is
38. End the atpm table update session atpm erase Erase all atpm tables from NVS atpm purge Purge entries from atpm table s atpm req Start atpm table update session atpm restore Restore atpm tables from NVS atpm store Store atpm tables into NVS atpm slist Display atpm system parameters atpm sys Set atpm system parameters config activate Move the configuration from temporary area to act ve area config erase Erase the configuration from NVS config store Store the active configuration data into NVS clrscr Clear screen download Switch to download mode help Display help screen net reset Reset the system net set wan gateway Set default gateway s IP address 118 net set http TVP 224HR User s Guide Turn on off HTTP server net set wan 1p Set IP address net set ip preced Set IP precedence bits net set wan mask Set IP subnet mask net set wan speed Select Ethernet link speed net set user_pw Set password net show Display IP parameters net show hwstat Display hardware status ping Send ICMP echo request to another host show h323 Display H 323 parameter settings show version Show software versions set h323 Set H 323 parameters tel show tel_id Display line impendence setting tel show port Display hook state for a telephony port tel show ring freq Show ringer s frequency tel set tel_id Set line impendenc
39. HENGE TCP IP DNS Server EES a ee e ee ooo j Figure 12 Windows NT4 0 DNS 31 Checking TCP IP Settings Windows 2000 1 Select Control Panel Network and Dial up Connection 2 Right click the Local Area Connection icon and select Properties You should see a screen like the following Local Area Connection Properties El Eg General Connect using B3 SMC EZ Card 10 100 SMC1211Tx Components checked are used by this connection Client for Microsoft Networks Y a File and Printer Sharing for Microsoft Networks Internet Protocol TCP IP Install Uninstall Properties Description Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks I Show icon in taskbar when connected DK Cancel Figure 13 Network Configuration Win 2000 3 Select the TCP IP protocol for your network card 4 Click on the Properties button You should then see a screen like the following Internet Protocol TCP IP Properties 21x General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically C Use the following IP address IP address 7 A Subnet mask l s Default gateway f 5 Ob
40. IP Address of the TVP 224HR e Ensure your DNS Name Server settings are correct Chapter 5 Operation and Status This Chapter details the operation of the TVP 224HR the system status screen as well as the channel status screen Operation Once both the TVP 224HR and the PCs are configured operation is automatic However there are some situations where additional Internet configuration may be required e Applications which use non standard connections or port numbers may be blocked by the TVP 224HR s intrinsic firewall nature You can define such applications as Special Applications to allow them to function normally Refer to Chapter 6 Internet Features for further details Some non standard applications may require use of the DMZ feature Refer to Chapter 6 Internet Features for further details System Status Screen Use the Home link on the main menu to view this screen System Status WAN Interface Parameters MAC address 00 50 2d 00 f5 09 Dynamic DNS Disabled Access Mode Fixed IP IP address 60 248 111 217 Subnet mask 255 255 255 0 Default gateway 60 248 111 254 Pri DNS server 168 95 1 1 Sec DNS server 0 0 0 0 LAN Interface Parameters MAC Address DO 50 2d D0 f5 08 IP address 192 168 0 1 Subnet mask 255 255 255 0 DHCP server Enabled No of DHCP clients 30 Starting client addr 192 168 0 10 Firmware Version TWP 224HR Version 2 01 005 O9New 0418 Boot Load Version 1 01 DSP Image
41. ON MAINTENANCE OR USE OF TRENDWARE S PRODUCTS TRENDWARE SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING OR OTHER HAZARD LIMITATION OF LIABILITY TO THE FULL EXTENT ALLOWED BY LAW TRENDWARE ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY WHETHER BASED IN CONTRACT OR TORT INCLUDING NEGLIGENCE FOR TVP 224HR User s Guide INCIDENTAL CONSEQUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY KIND OR FOR LOSS OF REVENUE OR PROFITS LOSS OF BUSINESS LOSS OF INFORMATION OR DATE OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES AND LIMITS ITS LIABILITY TO REPAIR REPLACEMENT OR REFUND OF THE PURCHASE PRICE PAID AT TRENDWARE S OPTION THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE Governing Law This Limited Warranty shall be governed by the laws of the state of California AC DC Power Adapter Cooling Fan and Power Supply carry 1 Year Warranty 129 TVP 224HR User s Guide TRENDn TRENDware
42. S Configuration C Disable DNS Enable DNS Host Domain DNS Server Search Order ___a_an _ _ _ _ Add META Figure 8 DNS Tab Win 95 98 28 PC Configuration Checking TCP IP Settings Windows NT4 0 1 Select Control Panel Network and on the Protocols tab select the TCP IP protocol as shown below Network 2 xi Identification Services Protocols Adapters Bindings Network Protocols Y NetBEUI Protocol Y NWLink IPX SPX Compatible Transport Y NWLink NetBIOS Add Remove Properties Update Description Transport Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Cancel Figure 9 Windows NT4 0 TCP IP 2 Click the Properties button to see a screen like the one below Microsoft TCP IP Properties 12 x IP Address DNS WINS Address DHCP Relay Routing An IP address can be automatically assigned to this network card by a DHCP server If your network does not have a DHCP server ask your network administrator for an address and then type it in the space below Adapter PCI Fast Ethernet Adapter r Obtain an IP address from a DHCP server C Specify an IP address IPAdGress re SuLHEL IH est Default atenay DK Cancel Figure 10 Windows NT4 0 IP Address 29 3 Select the network card for your LAN 4 Select the
43. Set Password Telnet Access Interface Speed Status View current System Status Help Definitions of Graphical User Interface Terms and Parameters for Dial Plan Setup H 323 Configurations DDNS Manual Link to Trendware FTP Website online 66 TVP 224HR User s Guide user manual and support materials System Status Select Home In order to view the System Status page please navigate to Home The System Status page will display the following parameters Firmware Version TVP 224HR VoIP Gateway Version Boot Loader Version RTOS Version H 323 Stack Version DSP image Version TSG Version LAN Interface Parameters e IP precedence Ethernet MAC address IP address Subnet mask Default gateway 9 2 H 323 Configuration H 323 Status Page This page lists all current settings for H 323 Parameters 67 TVP 224HR User s Guide H 323 Settings Result h323 display_name Customer h323 h245_term_type 60 h323 rtp_port_base 30000 h323 out_fast_start off h323 in_fast_start off h323 h245_tunneling off h323 cisco_t38 on h323 callSignalPort 1720 h323 nat_call on h323 call_name h323 local_alert off h323 default_dtmf H323 V2 Signal No Alternate IP Defined h323 gk_mode off h323 h245_timeout 30000 h323 term_id h323 gk_fail H 323 Parameters For the most part end users will not be using these functions feat
44. TVP 224HR VoIP Gateway Router 4 Port 2FXS 2FXO User s Guide rRENDN e TRENDnet TRENDware USA What s Next in Networking Copyright 2005 All Rights Reserved TRENDware International Inc FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed in accordance with the instruction manual may cause harmful interference to radio communication Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense NICA7 O RAL e of S Ssimw0 c oO ye CE Declaration of conformity This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class A for ITE and EN 50082 1 This meets the essential protection requirements of the European Council Directive 89 336 EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility C Trademarks All brand company and product names are trademarks or registered trademarks of their respective companies Copyright Statement No part of this publi
45. This range also determines the number of DHCP clients supported See the following section for further details on using DHCP Save the changes Save the data on screen 24 DHCP Setup What does DHCP do A DHCP Dynamic Host Configuration Protocol Server allocates a valid IP address to a DHCP Client PC or device upon request The client request is made when the client device starts up boots The DHCP Server provides the Gateway and DNS addresses to the client as well as allocating an IP Address The TVP 224HR can act as a DHCP server Windows 95 98 ME and other non Server versions of Windows will act as a DHCP client This is the default Windows setting for the TCP IP network protocol However Windows uses the term Obtain an IP Address automatically instead of DHCP Client You must NOT have two 2 or more DHCP Servers on the same LAN segment If your LAN does not have other Routers this means there must only be one 1 DHCP Server on your LAN Using the TVP 224HR s DHCP Server This is the default setting The DHCP Server settings are on the LAN screen On this screen you can Enable or Disable the TVP 224HR s DHCP Server function Disable the DHCP by entering 0 in the number of clients field Set the range of IP Addresses allocated to PCs by the DHCP Server function TS You can assign Fixed IP Addresses to some devices while using DHCP provided that the Fixed IP Addresses Note are NOT within
46. USA What s Next in Networking TRENDnet Technical Support US Canada Support Center European Support Center Contact Contact Telephone 1 310 626 6252 Telephone Fax 1 310 626 6267 Deutsch 49 0 6331 268 460 Email support trendnet com Francais 49 0 6331 268 461 Espa ol 49 0 6331 268 462 Tech Support Hours English 49 0 6331 268 463 7 30am 6 00pm Pacific Standard Time Italiano 49 0 6331 268 464 Monday Friday Dutch 49 0 6331 268 465 Fax 49 0 6331 268 466 Tech Support Hours 8 00am 6 00pm Middle European Time Monday Friday TRENDware International Inc 3135 Kashiwa Street Torrance CA 90505 http www TRENDNET com Copyright 2005 All Rights Reserved TRENDware International Inc 130
47. Version 8 1 2 1 TSG Version R8 0 Gateway Build 4 Figure 17 System Status Screen 38 Operation and Status Data System Status Screen Wan Interface Parameters MAC Address The hardware address of this device as seen by remote devices on the Internet This is different to the hardware address seen by devices on the local LAN Dynamic DNS Enabled Disabled Access Mode This indicates the current connection method Fixed IP DHCP or PPPoE IP Address This IP Address is allocated by the ISP Internet Service Provider Subnet Mask The subnet Mask Network Mask for the IP Address above Default Gateway The IP Address of the remote Gateway or Router associated with the IP Address above Primary DNS Server The IP Address of the Domain Name Server which is currently used Secondary DNS Server The IP Address of a backup Domain Name Server which could be used if the Prmary DNS Server fails LAN Interface Parameters MAC Address The hardware address seen by devices on the local LAN This is different than hardware address of this device as seen by remote devices on the Internet IP Address The IP Address of the TVP 224HR Subnet Mask The subnet Mask Network Mask for the IP Address above DHCP Server This shows the status of the DHCP Server function either Enabled or Disabled For additional information about the PCs on your LAN and the IP addresses allocated to them
48. XS Internal Ext 11 is stripped and remaining 3 digits are sent to GW A 01 8 to 10 digits 2 Digit Taiwan Area Code are sent to GW B Remote Zone used to make calls to remote GW A FXO External to PSTN 01 89 TVP 224HR User s Guide Gateway B Hunt Group Table Hunt Group ID Hunt Type of Dest ID s Dest ID s 2 2 1 2 3 2 1 3 4 2 1 4 5 2 1 4 11 2 1 11 Gateway B Destination table Dest ID Mode Destination 2 Local Port 2 3 Local Port 3 4 Local Port 0 11 H 323 Dest 192 168 1 20 1720 TCP The above destination table has both local destinations and remote destinations When the gateways are taken out of this initial testing environment and implemented in the field the internet access settings will have to be updated Likewise the above remote destination IP will have to be updated to the field Destination IP address 10 5 Making a call between Gateway A and Gateway B Case 1 Gateway Phone to Gateway Phone Gateway B phone 203 calls Gateway A phone 203 Caller Operation at GW B Equipment Operation Receiver Operation at GW A Pick up phone 203 204 1 GW dial tone is heard io TVP 224HR User s Guide Dial 11203 11204 11800 1 Du Du is heard 11801 2 VolP call processing Ring back tone is heard 1 GW A Line 3 LED ON Phone 203 rings VolP Conversation VR Con
49. accounting information on gateway via RS 232 or gatekeeper Management RS 232 DCE mode Built in HTTP Web based remote management Telnet remote management Flash memory and built in TFTP allowing firmware and feature System upgrade upgrade via network Chassis Metallic 9 5 Desktop Dimensions L X W X H 241 x 135 x 45 mm 9 5 x 4 3 x 1 8 in Weight 1 9 kg 4 2 Ib 111 LED Indicators Interoperabilityt Input Voltage AC Power Requirement Operating environment Certification TVP 224HR User s Guide System 2 PWR CPU WAN 1 LNK ACT LAN 4 LNK ACT Voice 4 In Use Ringing Microsoft NetMeeting Cisco AS5300 3600 RADVISION gatekeeper Cisco gatekeeper 90 260 VAC auto ranging 50 60 Hz 12V DC 2 0A Operating temperature 0 50 C 32 122 F Humidity 90 non condensing CE FCC UL Signaling FXO Ports Loop start DTMF Number of channels 2 Interface connectors 2 RJ 11 2 pin modular jacks Line impedance 600 9 900 Q Complex line impedance Insertion loss 2 dB nominal Frequency response 300 Hz 3400 Hz 2 dB w r t 1004 Hz Return loss gt 18 dB Input level adjustment 6 dB to 6 dB Output attenuation 0 dB to 13 dB Longitudinal balance gt 45 dB Disconnect detection Signaling FXS Ports Loop current Customizable tone detection Loop start DTMF Number of channels 2 Interface connectors 2 RJ 11 2 pin
50. ain 2 After registration follow the Service Provider s procedure to request a Domain Name and have it allocated to you 45 3 Enter your DDNS data on the TVP 224HR s DDNS screen shown below 4 The TVP 224HR will then automatically ensure that your current IP Address is recorded and updated at the DDNS server If the DDNS Service provides software to perform this IP address update you should disable the Update function or not use the software at all 5 From the Internet users will be able to connect to your Virtual Servers or DMZ PC using your Domain name as shown on this screen Dynamic DNS Screen Select Internet on the main menu then Dynamic DNS to see a screen like the following Home DDNS Settings MA Internet Dyn DNS Of y Server Name Host Name User Name Set User Password AE Figure 22 DDNS Screen Data Dynamic DNS Screen DDNS Service DDNS Service You must register for the service at dyndns org Apply for a Domain Name and ensure it is allocated to you Details of your DDNS account Name password Domain name must then be entered and saved on this screen This device will then automatically ensure that your current IP Address is recorded by the DDNS Service Provider You do NOT need to use the Client program provided by some DDNS Service providers From the Internet users will now be able to connect to your Virtual Servers or DMZ PC using your Domain name DDNS
51. al line to PSTN Dialing 9 connects you PBX where 9 is dialed to connect to PSTN 7 The PSTN number to reach the PBX is 8888 2222 8 Telephone A s number is 7777 1234 and belongs to the local PSTN Gateway B 4 ports is configured as follows 1 Gateway B IP 192 168 1 55 mask IP 255 255 255 0 gateway IP 0 0 0 0 virtual IP 2 FXS Port 2 has an analog telephone set connected its phone number is 203 3 FXS Port 3 has an analog telephone set connected its phone number is 204 4 FXO Port 0 is registered as number 9 Dialing 9 connects you to the outside line 5 FXO Port 0 is connected to PSTN line 9999 3333 6 Telephone B s number is 6666 4321 and belongs to the local PSTN Gateway A IP setup 1 Navigate to Internet Access Fixed IP Menu 2 Type in IP Address 192 168 1 20 Subnet Mask 255 255 255 0 and Default IP Gateway Address 0 0 0 0 in the related fields 3 Click on Save 4 Click on Reboot Gateway B IP Setup 5 Navigate to Internet Access Fixed IP Menu 6 Type in IP Address 192 168 1 55 Subnet Mask 255 255 255 0 and Default IP Gateway Address 0 0 0 0 in the related fields 7 Click on Save 8 Click on Reboot Gateway A Dial Plan Setup FXS Ports to Analog Phones Gateway A has two phones on the FXS ports Telephone number 203 on Port 2 and 204 on Port 3 These numbers are part of the default dial plan and d
52. appropriate radio button Obtain an IP address from a DHCP Server or Specify an IP Address as explained below Obtain an IP address from a DHCP Server This is the default Windows setting Using this is recommended By default the TVP 224HR will act as a DHCP Server Restart your PC to ensure it obtains an IP Address from the TVP 224HR Specify an IP Address If your PC is already configured check with your network administrator before making the following changes 1 The Default Gateway must be set to the IP address of the TVP 224HR To set this e Click the Advanced button on the screen above e On the following screen click the Add button in the Gateways panel and enter the TVP 224HR s IP address as shown in Figure 11 below e Ifnecessary use the Up button to make the TVP 224HR the first entry in the Gateways list Advanced IP Addressing 21x Adapter Pci Fast Ethernet Adapter y A CP IP Gateway Address 12 1xj Gateway Address ae f r Gateways UST Downy Add Edit Remove TE T Enable Security Pe Cancel Figure 11 Windows NT4 0 Add Gateway 2 The DNS should be set to the address provided by your ISP as follows e Click the DNS tab e On the DNS screen shown below click the Add button under DNS Service Search Order and enter the DNS provided by your ISP 30 PC Configuration Microsoft TCP IP Properties UBT Downy Edta
53. ble Setup From the window please Select lt Add gt lt HuntGroup gt The following window will appear Please Enter Data as shown Click on Ok Pon TVP 224HR VoIP Gateway Router Add Hunt Group IDs Hunt Group ID 4 Destination ID O 4 More Destinations for The Same Hunt Group 5 From the Navigation Menu on the left side Select Dial Plan Table Setup 6 From the window please Select lt Add gt lt Local_Destination_Channel gt 7 The following window will appear Please Enter Data as shown 8 Click on Ok 86 TVP 224HR User s Guide TVP 224HR VoIP Gateway Router Add Local Destination ID Destination ID la als Channel Number 9 1 Continue entering the Gateway A Dial Plan as laid out in the tables below Telephone Table Hunt Group Table and Destination Table following the above procedures 2 After you have entered the Dial Plan make sure you Store Dial Plan to flash memory From the Navigation Bar on the left side Click on Store Dial Plan 3 The following screen will appear on the right side Click on YES TVP 224HR VoIP Gateway Router Store Dial Plan Settings To Flash Memory Ready to store Dial Plan settings to Non Volatile Storage Are you sure jal Plan Il Dial Plan Help ae tated B Dial Plan Setup Enter Gateway B Dial Plan into Gateway B as shown in the tables below Telephone Table Hunt Group Table and Destination Table following the above procedures 2 After en
54. c amp h323 configuration config erase Then access dial plan edit mode by entering atpm req Purge the dial plan from the database atpm purge all Store the changes atpm store Reset the network configuration to default net set fac_default Key in yes to re boot Appendix C Connecting throuq To use Telnet Internet Access must have been previously setup so that the gateway is visible on the internet See User Guide for More Information Alternatively you can use Telnet to locally access the TVP 224HR if you are under a router or switch and the TVP 224HR and your computer are in the same network segment To access the TVP 224HR Gateway from a remote location using Telnet perform the following tasks O Pomm me Open the windows command prompt and enter the telnet command followed by the IP address of the TVP None telnet XXX XXX XXX 224HR Gateway you want to access When the TVP 224HR Gateway prompts you to Login Login adiit enter the user name admin When the TVP 224HR Gateway prompts you for Password enter the password Console gt will appear The default password is 123 but it is recommended that the password be changed for security considerations Password 123 116 TVP 224HR User s Guide The password can be changed from the Web Browser Administration Password submenu page Type in ping xxx xxx xxx where xxx x
55. cation may be reproduced stored in a retrieval system or transmitted in any form or by any means whether electronic mechanical photo copying recording or otherwise without the prior writing of the publisher May 2005 Setup How to Use This Manual This manual was designed for the non technical users of the VoIP Gateway TVP 224HR It contains information about the functions of the TVP 224HR and instructions for its installation basic configuration and operation Read this section carefully for important information about the manual s organization Important Safety Instructions Before you plug the TVP 224HR into an electrical outlet carefully read all the installation instructions in Chapter 2 For your own safety and the safety of your equipment always take the following precautions e Follow instructions and warnings in the documentation e Never push any object through the fan vent or other openings in the equipment Such action may produce a short circuit causing fire electric shock or equipment damage e Keep the TVP 224HR away from all chemicals and sources of liquids Warning e Connection of the RJ45 connector from a TVP 224HR to TNV circuits can cause permanent damage to the TVP 224HR e Incorrectly connecting telephony devices to the RJ11 port on the Telephony Interface Module can cause permanent damage to the module Documentation Abbreviations Throughout this guide the user will come across a
56. ccess 1 Select On or Off 2 Click on OK 3 Reboot Interface Speed 1 Select AUTO 10 MB Full Duplex or 100 MB Full Duplex 2 Click on OK 3 Reboot 9 11 Channel Status System status on all Channels in Table format Here you will find helpful definitions to common parameters in the TVP 224HR User Interface In addition from the main page in the help menu you can link to the Trendware FTP website and download the most current User Guide and support materials ftp trendware com T VP 224HR TVP 224HR User s Guide Chapter 10 Making Calls with TVP 224HR This chapters shows how to make phone calls from telephony devices connected to the TVP 224HR directly through or indirectly 10 1 Configuration Examples Default Dial Plan Before any configuration set up your TVP 224HR should have the following basic default information Network IP 192 168 0 1 Mask 255 255 255 0 Gateway 0 0 0 0 Dial Plan No Hunt Group Dest ID Dest 201 1 1 0 local port 1 202 2 2 1 local port 2 203 3 3 2 204 4 4 3 1 Ifyour TVP s two FXS ports are connected to two E telephones say port 2 and port 3 respectively just pick up phone 203 and dial 204 phone 204 203 should ring y 2 42049 TVP gt local port 3 gt 2 81 TVP 224HR User s Guide You may also check the LED indicators on the TVP 224HR When it rings d the related LED should flash After you pick up the handse
57. ccess to remote extensions 4 Simplified dialing makes remote offices and branches feel like local extensions Two TVP 224HR Gateways Both Gateways are set up with default settings 1 TVP 224HR A located site A 2 TVP 224HR B located on site B 93 TVP 224HR User s Guide Register DDNS name for both Dynamic IPs See Chapter 6 e tvpl dyndns org is applied for TVP 224HR on site A e tvp2 dyndns org is applied for TVP 224HR on site B Clients used on this topology e TVP 224HR on site A has PPPoE and DDNS clients enabled e TVP 224HR on site B has DHCP and DDNS clients enabled Network topology illustrated as follows INTERNET e 22 Ext ye DDNS Name gt wl dyndns org DONS Mame lt tvp2 dyndns org 11 Ext TVP 224HR PPPoE TVP 224HR DHCP 203 DDNS Client Enabled DDNS Client Enabled FXS Site A Site B 94 TVP 224HR User s Guide TVP 221HTVP 224HR configuration ADSL PPPoE connection on site A Web Configuration Telnet Console Local from a PC in same Segment From the Logon to the Web Configuration by Open opening your browser 1 Enter 192 168 0 1 2 Youwill be prompted for Username and Password Default Username and Password are admin and 123 respectively Web Configuration of Internet Access Internet Access PPPoE 1 Select Yes to enable PPPoE function 2 Enter username and password provided by your ISP 3 Click on Save Router Conf
58. ck that the cord is securely plugged into the power socket on the rear of the console 3 Check that the other end of the power adapter or power cord is securely plugged into the power outlet 4 If both ends of the power cord are properly connected and there is still no power the gateway might have a faulty power outlet power adapter or cord 5 Change to another power outlet or obtain another power adapter or cord LNK LED is not illuminated 1 Check that the TVP 224HR was connected correctly a Powered on b Correctly connected 2 Make sure connectors at both ends are securely seated 3 Check the TVP 224HR IP setting is correct Line port LED is not illuminated when I pick up the phone 1 Check the RJ11 telephone line to make sure it is correctly connected to both telephone set and line port There is no dial tone when I pick up the phone 1 Check the Line port LED to make sure it is illuminated 2 Check the RJ11 telephone line to make sure it is connected correctly to both phone set and line port There is an out of service tone when dialing the destination phone number 1 Check the dial plan setting address table hunt group table and destination table at the destination phone number There is no connection tone when dialing the destination phone number 2 Check the IP network Ethernet cable Ethernet port and GW IP setting is connected correctly 3 Check the destination TVP 224HR and phone is available Final Steps If t
59. d the IP Address of the TVP 224HR as in this example which uses the TVP 224HR s default IP Address HTTP 192 168 0 1 If you can t connect If the TVP 224HR does not respond check the following The TVP 224HR is properly installed LAN connection is OK and it is powered ON You can test the connection by using the Ping command e Open the MS DOS window or command prompt window e Enter the command ping 192 168 01 If no response is received either the connection is not working or your PC s IP address is not compatible with the TVP 224HR s IP Address See next item If your PC is using a fixed IP Address its IP Address must be within the range 192 168 0 2 to 192 168 0 254 to be compatible with the TVP 224HR s default IP Address of 192 168 0 1 Also the Network Mask must be set to 255 255 255 0 See Chapter 4 PC Configuration for details on checking your PC s TCP IP settings Ensure that your PC and the TVP 224HR are on the same network segment If you don t have a router this must be the case 4 You will be prompted for a username and password as shown below 21 Connect to 192 168 0 1 i 7 index htm User name e Password Remember my password Figure 2 Password Dialog e Enter Username and Password Default User Name and Password are admin and 123 respectively e These are the default values Both the name and password can and should be changed using t
60. de 9 GateKeeper ID To specify Gate Keeper s ID You ll have to reboot the system to make your changes take effect Aliases For the most part end users will not be using these functions features and or should use the default settings For more information please see the Advanced User Manuals or consult with your Systems Integrator H 323 Aliases Settings add Alias Delete All Previous Aliases Alias This field is to create or delete aliases that are registered with the gatekeeper The primary function of the gatekeeper component is to provide address translation services This function converts external telephone number addresses and alias name addresses to network addresses allowing users to maintain the same telephone numbers or alias addresses regardless of changes to their network addresses 71 72 TVP 224HR User s Guide TVP 224HR User s Guide 9 3 Dial Plan Settings Dial Plan Setup Phone Hunt Group Destination Setup Menu Add Y Telephone v Number s IDs 9 Help Using the function scroll bar on the right you are able to Add Delete Find or List data to from one of 3 tables While it may appear that there are 5 tables Remote Destination IP Remote_Host_Name and Local_Destination Channel are all part of the Destination Table The following are the three tables 1 Telephone Table 2 Hunt Group Table 3 Destination Table a Remote Destination IP takes precedence over Hostna
61. destination phone number is legal the TVP 224HR will play two quick sounds Du Du to destination If the desired destination phone number is illegal the TVP 224HR will play three out of service tones please check the dial plan and your desired destination phone number 10 4 Web Browser Sample Dial Plan This section describes how to use a web browser to build a dial plan in the VoIP Gateway We suggest the following 83 TVP 224HR User s Guide Draw an application diagram to illustrate clarify application including 1 Local gateway IP setup 2 Local gateway local telephone number setup 3 Local gateway remote gateway IP 8 remote telephone number setup Note The Diagram below of Gateway A 8 B could be any combination of either the TVP 224HR connected to switch by WAN port or the TVP 221H Connected by LAN port The switch that joins these two gateways serves the purpose of initial lab configuration Under this configuration both GW must be in the same P segment Once the dial plans have been entered and tested the switch would be replaced by the public internet and the gateways would then have to be updated with the field application Internet Access Settings eg Public IP Address Subnet Mask and Gateway IP Address In addition all remote destinations in the dial plan must be updated with the actual application field IP Addresses Gateway B 192 168 1 55 TE100 S5Pplus Phone A Internet Call Segm
62. e 1 PC can use each Special application at any time Also when 1 PC is finished using a particular Special Application there may need to be a Time out before another PC can use the same Special Application The Time out period may be up to 3 minutes LES If an application still cannot function correctly try using the DMZ feature Note DMZ This feature if enabled allows one 1 device PC on your LAN to be exposed to all users on the Internet This allows unrestricted 2 way communication between the DMZ PC and other Internet users or Servers e This allows almost any application to be used on the DMZ PC e The DMZ PC will receive all Unknown connections and data e Ifthe DMZ feature is enabled you must select the PC to be used as the DMZ PC LES The DMZ PC is effectively outside the Firewall making it more vulnerable to attacks For this reason Note you should only enable the DMZ feature when required Dynamic DNS Domain Name Server This free service is very useful when combined with the Virtual Server feature It allows Internet users to connect to your Virtual Servers using a URL rather than an IP Address This also solves the problem of having a dynamic IP address With a dynamic IP address your IP address may change whenever you connect which makes it difficult to connect to you The Service works as follows 1 You must register for the service at www dyndns org using the dyndns org dom
63. e Internet through the TVP 224HR using only a single external IP Address The local invalid IP Addresses are hidden from external sources This process is called NAT Network Address Translation DSL amp Cable Modem Support The TVP 224HR has a 100BaseT Ethernet port for connecting a DSL or Cable Modem All popular DSL and Cable Modems are supported SingTel RAS and Big Pond Australia login support is also included PPPoE The Internet WAN port connection supports PPPoE PPP over Ethernet Fixed or Dynamic IP Address On the Internet WAN port connection the TVP 224HR supports both Dynamic IP Address IP Address is allocated on connection and Fixed IP Address Advanced Internet Functions Special Internet Applications Applications which use non standard connections or port numbers are normally blocked by the Firewall The ability to define and allow such applications is provided to enable such applications to be used normally Virtual Servers This feature allows Internet users to access Internet servers on your LAN The required setup is quick and easy DMZ One 1 PC on your local LAN can be configured to allow unrestricted 2 way communication with Servers or individual users on the Internet This provides the ability to run programs which are incompatible with Firewalls QOS This feature guarantees better service to selected traffic on a network The goal in configuring QoS is to give priority and attention to c
64. e Internet IP address of this device port number is the port number assigned on this screen 9 You should then be prompted for the password for this device You must assign a password Settings HTTP Check this to allow web administration management via the Internet To connect see above If Disabled this device will ignore management connection attempts from the Internet Telnet Check this to allow Telnet administration management via the Internet To connect see above If Disabled this device will ignore management connection attempts from the Internet IP Address To manage this device via the Internet you need to know the IP Address of this device as seen from the Internet This IP Address is allocated by your ISP However if you are using a Dynamic IP Address this value can change each time you connect to your ISP There are 2 solutions to this problem Have your ISP allocate you a Fixed IP address Use the DDNS feature Internet menu so you can connect using a 53 TVP 224HR User s Guide Domain Name rather than an IP address Trusted Telnet This allows you to restrict remote access by IP address To enable Clients enter the IP address of the trusted client Ping Reply If enabled this service allows the TVP 224HR to reply when pinged To connect from a remote PC via the Internet 1 Ensure your Internet connection is established and start your Web Browser 2 Inthe Address bar
65. e for GW line interface tel set ring freq Set ringer s frequency Command Description Help Download Mode Commands Display help screen Quit Switch to normal operation mode net set wan gateway Set default gateway s IP address net set wan ip Set IP address net set wan mask Set IP subnet mask start Start downloading file 119 TVP 224HR User s Guide Appendix E Factory Default Settings The following table lists the settings of certain parameters before the TVP 224HR is shipped Parameter Default Setting Network PPPoe disabled DYN DNS disabled DHCP Server enabled Configured IP address 192 168 0 1 Configured IP subnet mask 255 255 255 0 Default gateway IP address 0 0 0 0 Current active IP address 192 168 0 1 Current active subnet mask 255 255 255 0 IP precedence 0000 Ethernet MAC address 00 50 2d xx xx xx Ethernet link speed 10 100 auto negotiation User ID for HTTP browser and Telnet client login admin Password for HTTP browser and Telnet access 123 login HTTP server enabled Telnet server enabled Serial port Fixed Baud rate 19 200 Number of data bit 8 Parity check None Number of stop bit 1 Flow control None H 323 h323 display_name customer h323 h245_term_type 60 h323 rtp_port_base 30 000 h323 out _fast_start Off 120 TVP 224HR
66. e number of the hunt group the TVP 224HR attempts to terminate the call at each of the destinations in the hunt group one at a time until a call is successfully completed Every destination that can be reached by dialing a phone number is a member of at least one hunt group When an address is presented to ATPM for lookup the output is a hunt group ID number As a second step the hunt group ID is presented to ATPM to get the list of members To effectively bypass the hunt group feature simply assign a unique hunt group number to a single destination In effect the Hunt Group will just have this one member 8 5 Dial Plan The dial plan is a database inside the TVP 224HR that allows the ATPM to map telephone numbers dialed to IP addresses of remote VoIP Gateways The dial plan consists of three tables destination table hunt group table and the address table Users need to setup these tables in order for the TVP 224HR to process calls to remote VoIP Gateways Address Table The address table maps a phone number to a hunt group The table contains entries that specify the following information e Telephone number e The hunt group the phone number maps to e The minimum number of digits to collect before the ATPM starts address lookup e The maximum number of digits the ATPM collects before it considers the dial string is complete e Number of digits forwarded to the destination 62 TVP 224HR User s Guide e Address table sam
67. eeeaeeeeeeereneeees 92 10 6 VoIP in a Dynamic IP environment cccsscscsssssssssssscsscsssescsssnessesnessessessesees 92 10 7 PPPoE DHCP and DDNS clients csccsssscssssssssscssscssssssssscsssessssscsssessssssssessees 93 Case 4 Gateway Prefix Simplified Gateway Phone to Gateway Pho0N oooooccinninnnn 93 10 8 Dial in PLAR Hotline TVP 224HR TVP 224HR noccncniccononononocnorncnocsocononocos 100 Case 5 PLAR Hotline FXO to FXS example coooooooocicccoonononocononnnonnconnc nono nono nconncon conocio 100 Case 6 PLAR Hotline FXS to FXO example oooooonnoniccnionononocononnnonnconoconoco nono nocnnconncnnnonno 103 Case 7 PLAR Hotline FXO to FXO example ccecceccesseesseesceeseeesceeeceseceseesseeneeeeeenes 105 CHAPTER Tlatarasiaiaa tues sanusnsnsned sususunusnsvensdtueusemveeiute 107 TELEPHONY CONNECTIONS ccnciiniinainainaiainan mimi mni 107 11 1 SN AAA A 107 Application 1 Special FXS Connections ccccccecsessseesceeeceesceeeceecesecneeceecaeeeseeeseesneeereees 108 Application 2 FXO Connections coooocooncocnconnconconnconncnn nono nonn non ron nnn nr ron e a ran ran ninia 108 CHAPTER Zi a ii 109 TROUBLESHOOTING TIPS wisiciecciecsieccsccciecccecsieccscccceccsecsteccscccccccteecees 109 O RON 109 General Problems sssccscsssssscssssscescsssescssssessssnsscesssscoscsssescessnessssscscessssossessnesssssessesoess 109 Internet A A 109 Other Problems cscscsscssscsssssce
68. elephone number dialed by users decides whether the dial string is part of the dial plan and if it is maps it to a remote TVP 224HR TVP 224HR When the call is set up to the destination a sub string of the original dial string will be sent along to the remote VoIP Gateway 8 3 Destination The destination is where a call is terminated Typically for inbound calls from the IP network the TVP 224HR terminals the call at one of the telephony ports The 61 TVP 224HR User s Guide destination for the call is the telephony port where the call terminated For calls initiated from telephony ports the TVP 224HR forwards the call to a remote TVP 224HR TVP 224HR via IP network and the remote TVP 221H TVP 224HR terminates the call The destination of the call is the remote TVP 224HR TVP 224HR 8 4 Hunt Group Instead of directly mapping a phone number to a destination the ATPM first maps the phone number to a group of destinations known as a Hunt Group A hunt group is a group of destinations that are equivalent For example the customer support group of a company might have 20 people who can handle support calls Access to customer support is through a single phone number but the next available support person is actually connected upon each incoming call These 20 phones would be configured as a hunt group A hunt group consists of a phone number and a list of destinations members of the group When an incoming phone number matches the phon
69. elnet or Web Browser firmware Upgrade using TFT as well as Access Control using Packet filters Overview Normally it is not necessary to use these screens or change any settings These screens and settings are provided to deal with non standard situations or to provide additional options for advanced users The screens available are Administrative This administrative screen allows you to change your password It is Password recommended that you change the default password immediately Remote Admin This feature allows you to manage the TVP 221HR via the Internet using your Web Browser or Telnet Upgrade The firmware software in the TVP 221HR can be upgraded using Firmware your Web Browser Access Control Administration Password Setup Login The Administration Password Page allows you to change your password on the TVP 224HR TVP 224HR VoIP Gateway Router Home Administrator Password Setup Internet Access OK Figure 25 Administration Password Setup Screen 51 TVP 224HR User s Guide Data Administration Password Setup Admin Login Old Password Enter the old password New password Enter the new password here If no password is required leave this blank If a password is set the password will be required in order to change the configuration Retype New Enter the new password here again This entry must match the password value above Buttons OK Click on OK
70. emote phone rings without digits being dialed This is a useful tool for customer requirements such as e The provision of an Off Premises eXtension OPX from a private branch exchange PBX Connection PLAR allows remote users on Foreign Exchange Station FXS ports to look to a central PBX like physical extensions e The provision of dial tone from a remote PBX Many customers want to offer toll bypass VoIP services without having the routers provide dial tone or change their existing dialplan This allows stations at remote sites to look like they are physically connected stations to a PBX Dial in PLAR Considerations and Limitations e Dial in PLAR is a switched VoIP call The call is setup on an as needed basis With connection PLAR no bandwidth is consumed while the phone is on hook When a phone connected to a POTS dial peer is taken off hook the call is automatically connected and the remote phone begins to ring e Dial in PLAR can work between any type or combination of Foreign Exchange Office FXO and or FXS telephony port device e Dial in PLAR does not collect digits from the connected Telephony device Once a dial plan has been entered into the ATPM PLAR can be enabled without need to alter the dial plan Note All other Dial plans set for this starting port will become ineffective 9 5 Store Dial Plan Store Dial Plan will store the Dial Plan from DRAM Working Memory to Flash Non Volatile Storage Always be
71. ent No Charge 7777 1234 Local Call Segment Local Charge This diagram serves the purpose of illustrating the possible analog phone PBX PSTN integration applications of the Gateway O However disconnect cadence provided by your phone company for your PSTN line and disconnect cadence provided by your PBX may require additional matching with the gateway This will require the assistance of your PBX supplier and or Systems Integrator Please also see User s Guide for additional information Scenario description Two gateways connected by a switch There are two gateways connected by a switch They are generically labeled Gateway but could be any combination of either the TVP 224HR connected to switch by WAN port or TVP 221H Connected by LAN port Theoretically GW A is 84 TVP 224HR User s Guide in Taiwan Local Area Code have 2 digits and GW B is in the US Local Area Codes have 3 digits Gateway A 4 ports is configured as follows 1 Gateway A IP 192 168 1 20 mask IP 255 255 255 0 gateway IP 0 0 0 0 virtual IP 2 FXS Port 2 has a telephone set connected its phone number is 203 3 FXS Port 3 has a telephone set connected its phone number is 204 4 FXO Port 0 is connected to PBX There are two telephone sets connected to the PBX Their extension numbers are 800 and 801 5 FXO Port 0 is registered as number 9 and it is connected to PBX 6 PBX has an extern
72. ertain devices or services so that they can use the maximum available throughput and speed available on a certain network when it is needed LAN Features DHCP Server Support Dynamic Host Configuration Protocol provides a dynamic IP address to PCs and other devices upon request The TVP 224HR can act as a DHCP Server for devices on your local LAN and WLAN Configuration amp Management Easy Setup Use your WEB browser from anywhere on the LAN or WLAN for configuration Remote Management The TVP 224HR can be managed from any PC on your LAN And if the Internet connection exists it can also optionally be configured via the Internet using a web browser or telnet Security Features Password protected Configuration password protection is provided to prevent unauthorized users from modifying the configuration data and settings NAT Protection An intrinsic side effect of NAT Network Address Translation technology is that by allowing all LAN users to share a single IP address the location and even the existence of each PC is hidden From the external viewpoint there is no network only a single device the TVP 224HR 13 1 2 Networking Protocols The TVP 224HR supports several industry standard networking protocols required for voice communication The following table describes these protocols Networking Protocol Description Internet Protocol IP IP is a messaging protocol that addresses and sends packets across the
73. erties for the TCP IP protocol Internet Access Problem 1 When I enter a URL or IP address I get a time out error Solution 1 A number of things could be causing this Try the following troubleshooting steps 1 Check if other PCs work If they do ensure that your PCs IP settings are correct If using a Fixed Static IP Address check the Network Mask Default gateway and DNS as well as the IP Address 2 Ifthe PCs are configured correctly but still not working check the TVP 224HR Ensure that it is connected and ON Connect to it and check its settings If you can t connect to it check the LAN and power connections 3 Ifthe TVP 224HR is configured correctly check your Internet connection DSL Cable modem etc to see that it is working correctly Problem 2 Some applications do not run properly when using the TVP 224HR 109 TVP 224HR User s Guide Solution 2 The TVP 224HR processes the data passing through it so it is not transparent 1 Use the Special Applications feature to allow the use of Internet applications which do not function correctly 2 If this does solve the problem you can use the DMZ function This should work with almost every application but 3 Itis a security risk since the firewall is disabled Note Only one 1 PC can use this feature Other Problems Power PWR LED is not illuminated 1 Check the power adapter connection 2 Ifthe power adapter or power cord is connected to the gateway che
74. g screens or your data will be ignored 23 LAN Configuration From the main menu navigate to Router Configuration Click on the LAN sub menu The LAN screen will appear as below TVP 224HR VoIP Gateway Router LAN Configuration Settings IP address 192 168 0 1 Subnet mask 255 255 255 0 DHCP Server No of client ET Client start address 192 168 0 10 TFTP Server Disable v Figure 4 LAN Screen Data LAN Screen TCP IP IP Address Subnet Mask DHCP Server Buttons IP address for the TVP 224HR as seen from the local LAN Use the default value unless the address is already in use or your LAN is using a different IP address range In the latter case enter an unused IP Address from within the range used by your LAN The default value 255 255 255 0 is standard for small class C networks For other networks use the Subnet Mask for the LAN segment to which the TVP 224HR is attached the same value as the PCs on that LAN segment DHCP Server is by default always on The TVP 224HR will allocate IP Addresses to PCs DHCP clients on your LAN when they start up If you are already using a DHCP Server this setting must be Disabled and the existing DHCP server must be re configured to treat the TVP 224HR as the default Gateway See the following section for further details The Start IP Address and Finish IP Address fields set the values used by the DHCP server when allocating IP Addresses to DHCP clients
75. hat the IP does not conflict with the range of IP s allocated by the TVP 224HR s DHCP Server If you are trying to access the TVP 224HR from a PC in the same segment as the TVP 224HR LAN Open your browser and enter a Enter 192 168 0 1 If you would like to access the TVP 221H from the WAN side from a remote PC with Internet Access b Enter tvp1 dyndns org You will be prompted for Username and Password Default Username and Password are admin and 123 respectively You could then continue as below Web Configuration of Dial Plan TVP 224HR User s Guide Telnet from a PC in same Segment From Windows command prompt Enter telnet 192 168 0 1 Enter Username admin Enter 123 From Windows command prompt Enter telnet 192 168 0 1 Enter Username admin Enter 123 net set dhcp on net set ddns on net set ddns add dyndns tvp2 username2 password2 net store From the local connection you could continue on setting up the dial plan However you could choose to reboot Enter net reset Connect a PC directly to your TVP 224HR making sure they are in the same LAN segment From the windows command prompt Enter telnet 192 168 0 1 Or from a remote computer Enter telnet tvp2 dyndns org Enter Username admin Enter 123 You would then continue as below 98 Dial Plan Settings Dialplan Table Setup
76. he AdministrationPassword page Once you have changed either the name or the password you must use the current values Home Screen After Logging on to the TVP 224HR you will see the Home screen which is the System Status page When you connect in future you will see this screen when you connect An example screen is shown below 22 A TVP 224HR VoIP Gateway Router Main Page Microsoft Internet Explorer EN English Unitec s El http 192 168 0 1 File Edit View Favorites Tools Help Qe gt Q x a JO search Sfp Favorites Q Meda O System Status WAN Interface Parameters MAC address 00 50 2d 00 f5 09 Dynamic DNS Disabled Access Mode Fixed IP IP address 60 248 111 217 Subnet mask 255 255 255 0 Default gateway 60 248 111 254 Pri DNS server 168 95 1 1 Sec DNS server 0 0 0 0 LAN Interface Parameters MAC Address 00 50 2d 00 f5 08 IP address 192 168 0 1 Subnet mask 255 255 255 0 DHCP server Enabled No of DHCP clients 30 Starting client addr 192 168 0 10 Firmware Version TYP 224HR Version 2 01 005 O9New 0418 Boot Load Version 1 01 DSP Image Version 8 1 2 1 TSG Version R8 0 Gateway Build 4 Figure 3 Home Screen Navigation amp Data Input e Use the menu bar on the top of the screen and the Back button on your Browser for navigation e Changing to another screen without clicking Save does NOT save any changes you may have made You must Save before changin
77. he Fast start mode on the outgoing side of the link 5 Incoming Fast Start The default setting is off This field is to enable or disable the Fast start mode on the incoming side of the link You ll have to reboot the system to make your changes active Frame Rate 2 frames packet 6 Auto Answer Enables quick H 225 to H 245 transition without waiting for receiver picking up the phone default is on 7 NAT Call Mode Enables calls from remote sites which use NAT routers with private IP networks behind default is on 8 Default DTMF Mode H323 V2 Signal or IMTC The default is H323 V2 Signal 9 DNS IP Address 10 Alternate DIMF IP Address 11 DTMF Duration default is 300 Gatekeeper This page is home to many specific H 323 Gateway Gatekeeper functions features For the most part end users will not be using these functions features and or should use the default settings For more information please see the Advanced User Manuals or consult with your Systems Integrator The primary function of the gatekeeper component is to provide address translation services This function converts external telephone number addresses and alias name addresses to network addresses allowing users to maintain the same telephone numbers or alias addresses regardless of changes to their network addresses 69 TVP 224HR User s Guide H 323 GateKeeper Settings GateKeeper Operation of 5 GateKeeper IP Address 0 0 0 0 Allow Cal
78. he Site B Gateway through a FXO port and passed on to the PBX system The PBX system will then forward the call to the dedicated terminal extension TVP 224HR Site B INTERNET Site A es Normal TVP 221H FXO Connection f Normal FXS j Connection 108 TVP 224HR User s Guide Chapter 12 Troubleshooting Tips This section provides solutions for problems you may possibly encounter while installing and connecting your VoIP Gateway Overview This chapter covers some common problems that may be encountered while using the TVP 224HR and some possible solutions to them If you follow the suggested steps and the TVP 224HR still does not function properly contact your dealer for further advice General Problems Problem 1 Can t connect to the TVP 224HR to configure it Solution 1 Check the following 1 The TVP 224HR is properly installed LAN connections are OK and it is powered ON 2 Ensure that your PC and the TVP 224HR are on the same network segment 3 If your PC is set to Obtain an IP Address automatically DHCP client restart it 4 If your PC uses a Fixed Static IP address ensure that it is using an IP Address within the range 192 168 0 2 to 192 168 0 254 and thus compatible with the TVP 224HR s default IP Address of 192 168 0 1 Also the Network Mask should be set to 255 255 255 0 to match the TVP 224HR In Windows you can check these settings by using Control Panel Network to check the Prop
79. he procedures in this section have not solved the problem reset the gateway several times by turning the power on and off If the problem still exists contact customer support 110 TVP 224HR User s Guide Ap pendix A Technical Specifications TVP 224HR Technical Specifications Telephony Interface Loop start 2 x FXO RJ 11 Loop start 2 x FXS RJ 11 Programmable line interfaces Complex line impedance H 323v3 Normal fast start mode Protocols Supports gateway gateway direct routing and gateway gatekeeper assisted routing mode Voice coders ITU T G 711 u law G 723 1 and G 729A B auto switching support Frame rate packet 1 8 Supports T 30 G3 fax on PSTN Interface ITU T T 30 fax Fax spoofing ITU T T 38 Simultaneous connections 4 channels voice fax Gain control G 168 echo cancellation 16 ms Voice activity Media processing detection VAD Comfort noise generation CNG Call progress detection DTMF detetection filtering regeneration H 323v3 IMTCv1 Physical interface WAN 1 10Base T 100Base TX Auto Negotiation LAN 4 10Base T 100Base TX Auto Negotiation Protocols TCP IP DHCP HTTP DNS QoS Virtual Server Port Forwarding Special application DMZ Advanced Function DDNS System Built in three tier dialing plan and destination hunting Call Control Supports gatekeeper authorization and accounting Supports gatekeeper call routing control and gateway mapping Call
80. ications Virtual Servers Port Fowarding DMZ QoS Change any of the following Administration related Chapter 7 settings Administration Admin Login Access Control Remote Administration Upgrade Firmware Where use of a certain feature requires that PCs or other LAN devices be configured this Note is also explained in the relevant chapter 20 Setup Configuration Program The TVP 224HR contains an HTTP server This enables you to connect to it and configure it using your Web Browser Your Browser must support JavaScript The configuration program has been tested on the following browsers e Netscape V4 08 or later e Internet Explorer V4 or later Preparation Before attempting to configure the TVP 224HR please ensure that e Your PC can establish a physical connection to the TVP 224HR The PC and the TVP 224HR must be directly connected using the Hub ports on the TVP 224HR or on the same LAN segment e The TVP 224HR must be installed and powered ON e Ifthe TVP 224HR s default IP Address 192 168 0 1 is already used by another device the other device must be turned OFF until the TVP 224HR is allocated a new IP Address during configuration Using your Web Browser To establish a connection from your PC to the TVP 224HR 1 After installing the TVP 224HR in your LAN start your PC If your PC is already running restart it 2 Start your WEB browser 3 Inthe Address box enter HTTP an
81. iguration Dynamic DNS 4 Select On 5 Enter Server Name Host Name User Name Password 6 Click on Save Connect RS 232 to TVP 224HR and PC Open Hyper Terminal Input parameters Baud rate Number of data bit 8 19 200 Parity check None Number of stop bit 1 Flow control None Enter 123 Local Telnet from a PC in same Segment From Windows command prompt Enter telnet 192 168 0 1 Enter Username admin Enter 123 net set pppoe on net set pppoe user name password net set ddns on net set ddns add server_name host_name user_name password eg dyndns org tvpl usernamel password1 net store 95 TVP 224HR User s Guide From the local connection you could continue on setting up the dial plan However you could choose to reboot Once Internet Access is setup you could choose to reboot the TVP 224HR and then use a PC in the same segment and with a web browser access theTVP 224HR Enter net reset If using the Router s DHCP Server make sure the routers DHCP Server is on and that the configuring PC is DHCP Client enabled Connect your PC directly to your TVP 224HR making sure they are in the same LAN segment From the windows command prompt If you would like your PC to have a Fixed IP Make sure that the IP does not conflict with the range of IP s allocated by the TVP 224HR s DH
82. is for connecting to telephony devices The FXO port is designed for connecting to PBXs or local telephone company central office switches CO The FXS port is designed for connecting to analog telephone sets G3 fax machines Warning connection of incorrect telephony devices to the ports on the TIM can cause permanent damage to the TIM and or the TVP 224HR 2 4 Connecting to the LAN Network The 4x RJ45 LAN network ports on the rear panel supports 10 100 Mbps half duplex connections to Ethernet You can use either Category 3 or 5 straight through UTP cable for 10 Mbps connections but use Category 5 for 100 Mbps connections Insert one end of the Ethernet cable into one of the 4 RJ45 ports on the rear panel of the TVP 224HR and other end of the cable to a network device PC 17 2 5 Assigning an IP address to the TVP 224HR The IP address is the unique logical address identifying each IP node such as the TVP 224HR on an IP network An IP address is a 32 bit number expressed as four decimal numbers from 0 to 255 separated by periods The TVP 224HR can be configured with a fixed IP address subnet mask and default gateway The TVP 224HR can also be setup as a DHCP Additionally the TVP 224HR can also be configured to use PPPoE With PPPoE you will have a Dynamic IP but combined with Dynamic DNS the TVP 224HR will automatically notify DynDNS of your changing IP Address and DynDNS will in turn map it to your registered Domain Name
83. istered Domain Name See Chapter 6 DDNS section for more information The first time you connect to the TVP 224HR for configuration you will need to connect to it under the same LAN segment to set the DHCP or PPPoE client To configure the TVP 224HR insert one end of an Ethernet cable into one of the 4 RJ45 LAN ports on the rear panel of the TVP 224HR and the other end directly to your PC Terminal By default the TVP 224HR s DHCP server is enabled Make sure your computer is DHCP client enabled See Chapter 4 PC Configuration If you choose to assign a Fixed IP to your PC make sure that you do not assign a IP that that is already allocated to the DHCP server for DHCP clients The TVP 224HR supports auto MDIX so Cat 5 cable will be sufficient Case 4 Gateway Prefix Simplified Gateway Phone to Gateway Phone After these dial plans are added users on Site A are able to dial 22 extension number to connect to users on site B for free VoIP telephony Users on Site B are able to call phones on Site A for free VoIP telephony by dialing 11 extension number Note There is a Max digit 5 limitation on the dial plan which allows the TVP 224HR to differentiate with potential PSTN numbers that may start with 11 or 22 but because they exceed 5 digits they would be handled differently The benefits of this dial plan are 1 Simplified setup 2 VolP Free calls to remote site extension 3 Simplified dialing ensures easy direct a
84. l Changes Each telephony port of the TVP 224HR must be assigned a unique destination ID Fill out the worksheet for local destinations by designating each port a unique destination ID 9 4 Dial in PLAR CID Data Dial in PLAR CID Screen DDNS Service Enter PLAR Address which could be any destination telephone PLAR Address number already entered into the dial plan This programs the gateway to automatically connect you to that number This port will not be able to dial any other numbers when PLAR is used CID Numb This is a separate feature to PLAR If you would like to have the d N pis Caller s Identification including Number and Name forwarded to the ade recipient please provide the information in the provided fields Buttons OK On Off AS Internet Acc Epe Dial Plan Settings B Dial Plan Setup B PLAR address CID Store Dial Plan r Dial Plan tore Dial Plan TVP 224HR VoIP Gateway Router PLAR address CID Port E i Caller ID hc Sia a 1 FXO j MM 2 FXO i 3 FXS 4 FXS Private line automatic ringdown PLAR circuits have statically configured endpoints and do not require the user dialing to connect calls The PLAR feature provides an easy method to create a switched Voice over IP VoIP call without digit dialing PLAR connections are often referred to as a bat phone or hotline type of application This is when a phone goes off hook 76 TVP 224HR User s Guide and a r
85. lease see the Packet Filter Screen 56 a Help Packet Filter TVP 224HR User s Guide TVP 224HR VoIP Gateway Router Packet Filter Setting Menu This feature allows you to define packet filters You may define what kind and which range of packets should be blocked discarded Select a Workgroup number 0 v Operation Add Protocol type TCP v Blocked Port Range From To Workgroup Select the group you wish to apply the filter too Number Add Delete List Pick the operation you would like to perform to the IP or MAC address TCP UDP Both Choose the protocol you would like to filter Block Range Port Enter the port you would like to block See below for common port assignments Common Port Assignment These are common services applications and the ports they use for network access Services Notes Port Numbers HTTP 80 FTP 21 TELNET 23 POP3 110 SMTP 25 mIRC None NTP 123 PPTP 1723 Applications Notes Port Numbers AOL 5190 5193 AOL Instant 5190 Messenger AIM AOL ICQ 5190 dynamic gt ICQ Firewall Settings 1024 BAYVPN 500 CarbonCopy32 1023 1680 CITRIX 1494 Cu SeeMe Cornell 1 1 7648 Direct Connect 375 425 FW1VPN 259 TVP 224HR User s Guide ICQ For file transfer ICQ gt None for chat Preference gt Connecti
86. lect the Channel 0 3 and Click on View Codec Selection Select the codec of your preference e G 711 PCM 64kbps A law and u law e G 723 1A ACELP M MLQ 5 3 6 3kbps G 729AB CS ACELP 8kbps Common Parameters Common Parameters is found under Common Settings and allots the amount of time given to each step of the dial process TVP 224HR User s Guide Common Settings Total Dial Time ms First Digit Wait Time ms Inter Digit Wait Time ms Termination Digit Save The Changes Clear All Changes Current Common Parameter Settings Are System Info Total dial time 30000ms First digit wait 10000ms Interdigit wait 5000ms Dial term digit None Total Time The total amount of time you have to enter a telephone number Default 30000ms First Digit Wait Time The amount of time you have to enter your first digit Default 10000ms Inter Digit Wait Time The amount of time you have between each digit entered Default 5000ms Termination Digit A special number which tells the gateway that you have finished entering your telephone number and that the number should be processed Default none 9 9 Channel Parameters Allows you to set parameters associated with each port such as transmission receive gains and comfort noise level 9 10 Administration Password See Chapter 7 1 Enter Old Password 2 Enter New Password TVP 224HR User s Guide 3 Retype New Password Telnet A
87. ller of the 2 values auto negotiated or entered here will be used For direct connections not PPPoE or PPTP the MTU used is always 1500 Buttons OK After entering data click on OK to save settings You will also have to reboot the device to make the settings take effect 43 Special Applications If you use Internet applications which use non standard connections or port numbers you may find that they do not function correctly because they are blocked by the TVP 224HR s firewall In this case you can define the application as a Special Application Special Applications Screen This screen can be reached by clicking the Special Applications submenu located under the Router Configuration main menu You can then define your Special Applications You will need detailed information about the application this is normally available from the supplier of the application You can also reference the Common Port Setting page Also note that the terms Incoming and Outgoing on this screen refer to traffic from the client PC viewpoint TVP 224HR VoIP Gateway Router Special APP Setup Index Active in oor SMAPS Te Description Protocol From To Protocol From To 1 TCP y TCP v 2 TCP mM TCP y 3 TCP TCP v 4 TCP y TCP y 5 TCP y Ter A LO JILO JL 6 TCP v TCP v 7 TCP Y TCP y fl E E 8 TCP TCP E 9 TCP y
88. lose their connection When the upgrade is finished the TVP 224HR will restart and this management connection will be unavailable during the restart Cancel Cancel does NOT stop the Upgrade process if it has started It only clears the input for the Upgrade File field To perform the Firmware Upgrade 1 Click the Browse button and navigate to the location of the upgrade file 2 Select the upgrade file It s name will appear in the Upgrade File field 3 Click the Update button to commence the firmware upgrade LS The TVP 224HR is unavailable during the upgrade i process and must restart when the upgrade is Note completed Any connections to or through the TVP 224HR will be lost Access Control This feature is accessed by the navigating to the Access Control menu The Access Control feature allows administrators to restrict the level of Internet Access available to PCs on your LAN With the default settings everyone has unrestricted Internet access To use this feature 1 Set the desired restrictions on the Default group All PCs are in the Default group unless explicitly moved to another group 2 Set the desired restrictions on the other groups Group 1 Group 2 Group 3 and Group 4 as needed 3 Assign PC to the groups as required LES Resirictions are imposed by blocking Services or types of connections Common Services have not been re pre defined Note Please see common port assignme
89. ls Without GateKeeper tue Registration Type gateway y Max Registration Retries 3 Time To Live Endpoint Prefix Terminal ID GateKeeper ID 1 Gate Keeper Mode The default setting is off This field is to select the co operation mode with some other gatekeeper s Three options are available i Off Disables gatekeeper co operation ii Auto Enables auto discovery of the gatekeeper iii Manual Enables gatekeeper co operation in manual operation the gatekeeper address must be properly assigned The following fields must be filled in when Gate Keeper Mode is set to either auto or manual 2 Gate Keeper Address Specify the gatekeeper address when configured to manual mode When auto mode is desired this field should be set to auto 3 Allow Calls Without Gate Keeper This field is to inform the H 323 stack to allow calls when the endpoint is not registered with a gatekeeper 4 Registration Type This field is to set the endpoint registration type This specifies how the endpoint will register itself with the gatekeeper 5 Max Registration Retries This field is to control how many registration attempts will be made before the endpoint considers itself to have failed registration 6 Time To Live 7 Endpoint Prefix This command is used to set the H 323 prefix that the TVP 224HR uses when registering to an H 323 gatekeeper 8 Terminal ID To specify GW s ID 70 TVP 224HR User s Gui
90. lt group 60 TVP 224HR User s Guide Chapter 8 TVP 224HR Telephony Concepts The TVP 224HR enables the transmission of voice and fax traffic over any IP network by digitizing voice and fax signals encapsulating the information within IP packets and then sending the packets across the IP network 8 1 How the TVP 224HR Operates 1 The TIM inside the TVP 224HR digitizes analog voice signals at 8 Kbps 2 TVP 224HR system software handles the e Capture of telephone number presented as DTMF tones e Mapping the telephone number to the IP address of remote VoIP Gateway e Setting up calls with remote TVP 224HRs utilizing H 323 call control protocol e Digitizing compressing and encapsulating the voice into IP packets and transmission of the IP packets onto the Ethernet LAN 3 The TVP 224HR router forwards the IP packets across the WAN where they will be received by another VoIP Gateway at the remote 4 The process is reversed at the remote VoIP Gateway 8 2 ATPM To allow you to easily dial a telephone or fax on the network the TVP 224HR maps a series of dialed digits to the IP address of the remote TVP 224HR whose phone or fax you are calling This mapping information is contained in a database inside each TVP 224HR called the dial plan Based on the dial plan the Address Translation and Parsing Manager ATPM inside the TVP 224HR maps telephony numbers to IP addresses of remote VoIP Gateways The ATPM collects t
91. lylz Alternative but required elements are grouped in braces and separated by vertical bars xlylz Optional alternative keywords are grouped in brackets and separated by vertical bars string A non quoted set of characters Do not use quotation marks around the string or the string will include the quotation marks key A key on the VT 100 terminal of terminal emulator For example lt Enter gt denotes the Enter key Table of Contents How to Use This Manual sssciscssccsisssscsssessesssssscesssnssessevstsessstecsessscevsscsesesssctesesbs ceesscescossevecsssessss 3 Important Safety InstructionS esesseesesoessesecsoesessossesoessescosoesessossesoessesoesoesessossessessesoessesessose 3 Documentation Abbreviations sscccssssscssssssccsssscccsssssccesssccsesseccscsssccsssseccsessseecessasescesnes 4 Notation Com ventions issisisesicisscees ctiettsatesctssesadeascasesstesoetissssstecsconscsdevncsesssdeassendeasseasesossbdeascaonse 5 CHAPTER Linda 12 SAA AVA E A aa 12 1 1 NETA tnis sosote s sinees seriste sis stesi erase sessin tess 12 Int rnet Access Pea UTOS ica llas hc eT E 13 Advanced Internet Functions seriais e E E E E E N E E RE 13 LAN Features ness a EE EEA a dt 13 Configuration amp Management cccccccccssesssessceesceesceeeceeceseceaeesaecaaecseecaeeeneeeeeseneeeeeeereeeeees 13 Security Feature Sii i i i ie i ei iei i 13 1 2 Networking ProtocolS mocomommmmssssmmrmmms 14
92. me b Destination Remote _Host_Name IP takes precedence over Hostname c Destination Local_Destination_Channel Telephone Number Table 1 From Navigation Bar Select Dial Plan Settings Dial Plan Table Setup 2 The default values are Add and Telephone Click on Select The following window will appear 73 TVP 224HR User s Guide Add Telephone Numbers Telephone Number 0 Hunt Group ID Min Digits 0 Max Digits 16 Strip Length 0 Append Prefix None More Entries for The Same Hunt Group Complete Al Clear All Changes From this window we can Add Delete Find or List desired telephone numbers and map them to a hunt group Parameter Description Telephone Telephone number to match This is only part of Number the total dialed string For each hunt group ID you need to assign it a unique identifier between 0 and 99 Minimum number of digits to be collected before Min Digits the ATPM starts matching the dialed string with entries in the address table Maximum number of digits to be collected before Max Digits the ATPM starts matching the dialed string with entries in the address table The number of digits to be stripped at the Strip Length beginning of the collected dial string before forwarding the string to the destination Optional Digit s to be added to the beginning of Append Prefix the collected dialed string before forwarding it to the destination Hunt Gr
93. network To enable IP protocol the TVP 224HR must have a Real IP address subnet and gateway assigned to it Voice over IP Protocol VoIP enables the TVP 224HR to transfer voice VoIP communications over an IP network The TVP 224HR employs ITU T H 323 protocol for setting up calls with one another Trivial File Transfer TFTP allows you to transfer files over the network The Protocol TFTP TVP 224HR implements a TFTP client allowing you to download new revision firmware from a TFTP server The TFTP client requires a TFTP server in your network Real Time Transport RTP is a standard for transporting real time data over IP RTP network The TVP 224HR uses RTP protocol to send digitized and compressed voice packets 1 3 Package Contents The contents of your product should contain the following items e TVP 224HR VoIP Gateway Router 4 port n 100 240V Power Adapter 9 pin straight through RS 232 cable Printed Quick Installation Guide User s guide CD RJ45 Cable 1 4 Front Panel The front panel of the TVP 224HR contains a push button and LED indicators The following figure illustrates the front panel of the TVP 224HR TVP 224HR VoIP Gateway Router Console 19200 n 8 1 4 port TVP 224HR Front Panel 14 Setup LED Indicators The LED indicators on the front panel display the current status of the TVP 224HR as described in the following table Indicator Color SO Indication PWR
94. nt for reference to common services 55 TVP 224HR User s Guide Access Control Screen To view this screen select the Access Contro Groups link from the main menu TVP 224HR VoIP Gateway Router br Home Workgroup Setting Menu F Internet The Access Control feature allows administrators to restrict specific service or Internet Access by individual PCs These restrictions apply only to traffic on the WAN port local LAN traffic is not affected Select a Workgroup number 1 Description m Help Operation Add _ Address type P Y Address Figure 29 Access Control Screen Data Access Control Screen Group Workgroup Select the desired Group Groups are named Default Group 1 Number Group 2 Group 3 and Group 4 and cannot be re named Description Enter the reference name description of the workgroup Address Type Use the Add Delete list scroll with the IP or MAC address field to IP or MAC Address create a group If the current group is Default then members can not be added or deleted This group contains PCs not allocated to any other group To remove PCs from the Default Group scroll to delete and enter the IP or MAC address you wish to delete To assign PCs to the Default Group delete them from the Group they are currently in Buttons OK Click on OK to confirm new data After creating a group you can start populating the group with packet filter restrictions Below p
95. number of abbreviations that are common throughout the industry The user should be familiar with the following abbreviations Address Translation and Parsing Manager Command Line Interface Digital Signal Processor Dual Tone Multi Frequency Foreign Exchange Office Foreign Exchange Station ITU specification for multimedia transmission over IP networks Internet Control Message Protocol International Multimedia Telecommunications Consortium Internet Protocol 4 port VoIP Gateway 4 port VoIP Gateway Router Key Telephone System Local Area Network Non Volatile Storage Light Emitting Diode Private Branch Exchange Public Switched Telephone Network Real Time Transport Telephony Channel Identifier Trivial File Transfer Protocol Telephony Interface Modules Telephone Network Voltage User Datagram Protocol Unshielded Twisted Pair Voice Activity Detection Wide Area Network Notation Conventions Setup Throughout this guide different type styles and characters are used These serve a variety of purposes as described below Convention Description boldface Commands and keywords are in boldface italic Arguments for which you supply values are in italics courier Messages that the TVP 224HR CLI displays are in plain courier font Elements in square brackets are optional x
96. o not have to be entered We can skip the local Dial Plan setup including Telephone Address hunt group and destination for phones 203 and 204 How to Enter the Dial Plan The Dial plan consists of three tables that include the Telephone Table Hunt Group eg Customer Service may have multiple phones that the GW must search through for an open line and Destination Table Both Local and Remote The dial plan has to be entered into all Gateways so that the local gateway knows how to process calls sending them to its local ports or to remote gateways for further processing 85 TVP 224HR User s Guide The following screen shots show an example for entering a dial plan for a single number This example should give you the necessary insight as to how to enter the rest of the Dial Plan If you still have difficulty understanding the dial plan and entering data please reference the User Manual for more examples From the Navigation Menu on the left side Select Dial Plan Table Setup From the window please Select lt Add gt lt Telephone gt The following window will appear Please Enter Data as shown Click on Ok Pon TVP 224HR VoIP Gateway Router Home Add Telephone Numbers Internet Ac e Telephone Number 0 800 Hunt Group ID Min Digits a Max Digits B Strip Length 0 Append Prefix None More Entries for The Same Hunt Group From the Navigation Menu on the left side Select Dial Plan Ta
97. on to each PC when the PC boots e For all non Server versions of Windows the default TCP IP setting is to act as a DHCP client If using a Fixed specified IP address the following changes are required e The Gateway must be set to the IP address of the TVP 224HR e The DNS should be set to the address provided by your ISP LES Do to NAT resolution issues it is not recommended to use the TVP 224HR under another Router Note PC Configuration Checking TCP IP Settings Windows 9x ME 1 Select Control Panel Network You should see a screen like the following Network 124 x Configuration Identification Access Control The following network components are installed NetBEUI gt PCI Fast Ethernet Adapter Y NetBEUI gt Dial Up Adapter NetBEUI gt Dial Up Adapter 2 VPN Support Y TCP IP gt PCI Fast Ethernet Adapter TCP IP gt Dial Up Adapter X TCP IP gt Dial Up Adapter 2 VPN Support File and printer sharing for NetWare Networks X 4 gt Add Remove Properties Figure 5 Network Configuration 2 Select the TCP IP protocol for your network card 3 Click on the Properties button You should then see a screen like the following TCP IP Properties 21x Bindings Advanced NetBIOS DNSConfiguration Gateway WINS Configuration IP Address An IP address can be automatically assigned to this computer If your network does not automatically assign IP addresses ask y
98. onments that the TVP 224HR can be applied to They are described in the following sections 107 TVP 224HR User s Guide Application 1 Special FXS Connections The following diagram illustrates two different types of connections The SITE A FXS Connection shows the normal connection between a gateway and telephone set POTS or FAX machine The other type of FXS connection is shown on SITE B on the right hand side The Connection between the gateway and PBX has a special CO trunk interface card The telephone sets connected to PBX can be either POTS or digital telephone depending upon the PBX capability TVP 224HR Site A A ge SSN TVP 221H FXS Connection w CO Trunk f Normal FXS Interface Card Connection Application 2 FXO Connections Application 2 has three possible connections One Site A the FXS connection to analog devices is normal and is identical to connections mentioned in Application 1 On Site B the connection between PSTN and PBX is also a normal connection The last connection is between PBX and the gateway which uses the internal analogue lines of the PBX In this case the FXO port has to be used Note If a digital PBX is used an analog terminal adapter is needed to provide an analog interface to the FXO port Please consult with your PBX supplier In this application the caller on Site A can make a call using a device connected to a FXS port on the Site A gateway The call will be routed to t
99. ons gt Firewall Set timeout to 80 seconds IPTV Cisco IPTV 2 0 0 None Laplink 1547 Lotus Notes 1352 MSN Messenger See this Microsoft Link for 6901 6891 6900 Including Voice detailed info including Windows 2000 Problems NetMeeting NetMeeting 2 1 and 2 11 1720 How to Establish 1503 NetMeeting Connections Through a Firewall PC Anywhere Host must be on the LAN side 22 and set 5631 5632 RealPlayer RealPlayer G2 None Remote Anything 3996 4000 Shiva VPN Set the mobile option to be 2233 your public IP address Virtual Network 5500 Computing 5800 5900 VDOLive None Vonage VoIP Phone 5060 5070 Service 10000 25000 Games Notes Ports Age of Empires II 23978 Aliens vs Predator 80 2300 2400 8000 8999 Asheron s Call May need to open MSN DX 9000 9013 ports Baldur s Gate 15000 Black and White 2611 2612 6500 6667 27900 Civilization 3 Consult this page You ll have 80 to click through an ad 6500 Civilization Conquests users 6667 should also consult the manual starting p 47 58 TVP 224HR User s Guide 13139 27900 28900 29900 29901 Dark Reign 2 26214 Delta Force 3100 3568 3999 Dune 2000 1140 1234 4000 Dungeon Siege 19271 Elite Force 26000 27500 27910 27960 Everquest 1024 6000 7000 F 22 Lightning 3 4533 4660 Fighter Ace II 50000 50100 Fighter Ace II DX 2300
100. ontained in stored on or integrated with any products returned to TRENDware pursuant to any warranty There are no user serviceable parts inside the product Do not remove or attempt to service the product by any unauthorized service center This warranty is voided if i the product has been modified or repaired by any unauthorized service center 11 the product was subject to accident abuse or improper use 111 the product was subject to conditions more severe than those specified in the manual Warranty service may be obtained by contacting TRENDware office within the applicable warranty period for a Return Material Authorization RMA number accompanied by a copy of the dated proof of the purchase Products returned to TRENDware must be pre authorized by TRENDware with RMA number marked on the outside of the package and sent prepaid insured and packaged appropriately for safe shipment WARRANTIES EXCLUSIVE IF THE TRENDWARE PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE THE CUSTOMER S SOLE REMEDY SHALL BE AT TRENDWARE S OPTION REPAIR OR REPLACEMENT THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TRENDWARE NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATI
101. orts are located on the rear panel Console There is a 9 pin RS 232 interface port on the front panel Their functions are described below Port Label Function 1x RJ45 Connecting to Cable ADSL Modem for Internet connection 4x E Comnecting the TVP 224HR to 10 100 Mbps Ethernet network pc pin RS 232 User Console Connecting the TVP 224HR to a VT 100 terminal or terminal emulator for configuring the TVP 224HR 16 Setup Chapter 2 Installing the TVP 224HR This chapter gives information on how to install the TVP 224HR 2 1 Network Requirements For the TVP 224HR to successfully operate in your network your network must meet the following requirements 1 A working 10 100 Base T Ethernet The TVP 224HR connects to the Internet via an Ethernet LAN 2 IP network that supports gateway and subnet mask You ll need a static IP address to assign the TVP 224HR or a DDNS account for your Dynamic IP 2 2 Installing the TVP 224HR Due to the TVP 224HR being used in a desktop configuration ensure that the TVP 224HR is placed in a clean well ventilated and vibration free environment When the TVP 224HR is used be certain that the unit is placed on a sturdy flat surface near a grounded power outlet At least three inches of clearance must be provided on both sides of the TVP 224HR for good ventilation 2 3 Connecting to the telephony devices The 4 port TVP 224HR supports 2 FXO and 2 FXS Each RJ11 port
102. ossesoessssoessssesss 52 Upgrade Firm Ware wisi cscccs scaseaessassescsccsessoessoiesodscussevssaneconsicnaesbadocssensseadsesdbasscssssassedosnesopessaaeses 54 ACCESS Control sic casas cscs ccssesssencaasesonseseeesbas sons sonsendeessoassensseaseunsandsasessvasovasonasoonsvasseaodansonsseadensees 55 Access Control Screen sa cisen le ri di 56 Common Port Assignment cenit dd cie da 57 CHAPTERS A AA dodne iii 61 TVP 224HR TELEPHONY CONCEPTS occcccccccccccccccccccccncncncncncnnnnnnnnnnnos 61 8 1 How the TVP 224HR Operates sccsscsssssssssscssccssscsssssccsscssecsscssscsssessscssssessseseeees 61 Be ATP AA ENESE EET 61 8 3 DestinatioWM sivcccsccscavcosscesceassssssossessscsscnsdavesseceossacnascceosaseunsossseessesssesdensesuseosszsnsvcoasscsvestede 61 4 UME Groups usasa NO 62 8 5 AS A oros sus sosea soss roso oro soso raoa soson seisoi r SSSss 62 Address Table nene iii 62 Hunt Group Table iia id 63 Destination Table iieii a ii ER E E E i 63 8 6 DTMF Relay ninisi A 63 TS O A RI 64 CHAPTER Q aaa 65 CONFIGURING VOIP FROM A WEB BROWSER eeeeeeeeeseeeeeseeeees 65 9 1 HTTP setting modesina sireno sses srn oS assor sss a Eee iE oeit 65 Main Menu Function Briefings ccccceecceescessceeeceseceseceneceecseecaeeeaeeeeeeeeeeeeeseeeseeeeeeeenaees 66 DYSLEMSLAUUS EN EEE TE E E EE EE E E 67 9 2 _ H 323 Configuration cccccciccsscscsocsosvssertoseesessecaseesocsssensousosessessenassoscesaesecssbassessesnesasees 67 o B PARI AT
103. oup ID Hunt Group Table 1 From Navigation Bar Select Dial Plan Settings Dial Plan Table Setup The default values are Add and Telephone Change Telephone to Hunt Group and Click on Select 3 A screen will appear showing the following page N 74 TVP 224HR User s Guide Add Hunt Group IDs Hunt Group ID Destination ID 0 More Destinations tor The Same Hunt Group l Complete Clear All Changes From this window we can Add Delete Find or List the desired hunt group ID and map it to a destination ID Destination ID Table NR From Navigation Bar Select Dial Plan Settings Dial Plan Table Setup The default values are Add and Telephone Change Telephone to Hunt Group and Click on Select 3 A screen will appear showing the following page Home BR Internet Add Remote Destination ID Destination ID IP Address or Host Name Note If both IP Address and Host Name are defined only IP Address will be recognized Company Location Complete II Clear All Changes The Destination ID is either a Remote Destination IP or Hostname but not both or a Local Destination Channel Please note that if a Remote Destination IP and a Hostname is specified the Remote Destination IP takes precedence 75 TVP 224HR User s Guide Help Add Local Destination ID Destination ID L Channel Number Complete il Clear Al
104. our network administrator for an address and then type itin the space below Specify an IP address Figure 6 IP Address Win 95 Ensure your TCP IP settings are correct as follows Using DHCP To use DHCP select the radio button Obtain an IP Address automatically This is the default Windows setting Using this is recommended By default the TVP 224HR will act as a DHCP Server Restart your PC to ensure it obtains an IP Address from the TVP 224HR Using Specify an IP Address If your PC is already configured check with your network administrator before making the following changes 27 e On the Gateway tab enter the TVP 224HR s IP address in the New Gateway field and click Add as shown below Your LAN administrator can advise you of the IP Address they assigned to the TVP 224HR Bindings Advanced NetBIOS DNS Configuration Gateway WINS Configuration IP Address The first gateway in the Installed Gateway list will be the default The address order in the list will be the order in which these machines are used New gateway 192 168 0 1 Installed gateways A Figure 7 Gateway Tab Win 95 98 e Onthe DNS Configuration tab ensure Enable DNS is selected If the DNS Server Search Order list is empty enter the DNS address provided by your ISP in the fields beside the Add button then click Add Gateway l WINS Configuration IP Address Bindings Advanced NetBIOS DN
105. p_id in the command corresponds to the Hunt Group ID in the worksheet the hunt_type corresponds to the Hunt Type 1 or 2 the dest_id corresponds to the List of Destination IDs You may alternatively use the web browser to add hunt groups to the hunt group table Hunt Type Hunt Group List of Destination IDs ID 1 2 124 TVP 224HR User s Guide ATPM Address Table Each phone number to be recognized by the TVP 224HR must have its first digits match an entry in the address table Fill out the address table worksheet and use the CLI command atpm aadd telf min_digits max_digits hunt_group_id prefix_strip_len prefix to add each entry in the worksheet to the address table The telf in the command corresponds to the Digits to Match in the worksheet the min_digits corresponds to the Min of Digits to Collect the max_digits corresponds to Max of Digits to Collect the hunt_group_id corresponds to the Hunt Group the prefix_strip_len correspond to No of Digits to Strip and the prefix corresponds to the Prefix String You may alternatively use the web browser to add telephone numbers to the address table Min Max No of Digits to Match of Digits of Digits Hunt Digits to Prefix to to Group Strip String Collect Collect 125 TVP 224HR User s Guide A F Address TablO oonononcnnnicnn 62 Fac
106. ple Hunt Min Max Digits Prefix Prefix Grp_Id Digits strip Address 20 11 5 5 2 None Hunt Group Table The hunt group table maps a hunt group to a list of destinations Hunt group sample Hunt Group ID Hunt Type of Dest ID s Dest ID s 1 2 1 1 3 2 1 3 4 5 1 4 11 2 1 11 Destination Table The destination table maps a destination to a telephony port or the IP address of a remote TVP 224HR Destination table sample Dest ID Mode Destination 1 Local Port 0 Local Port 2 4 Local Port 3 11 H 323 Dest 192 168 0 55 1720 TCP 8 6 DTMF Rela Voice from PSTN is compressed by the TVP 224HR before it is sent across the IP network and then decompressed by the destination VoIP gateway The voice codecs supported by the TVP 224HR are designed for ideally compressing and decompressing human voice If the compression decompression process is performed on DTMF tone which needs to be conveyed across IP network distortion might be too significant to be cognizable on the receiving end To overcome the shortcoming that the voice codecs may have encoding DTMF tone the TVP 224HR encodes DTMF tone into special packets The packets are then sent to the destination VoIP Gateway via a separate IP connection The destination VoIP Gateway decodes the packets generates the DTMF tone and then sends the 63 TVP 224HR User s Guide tone to the PSTN This method in which the TVP 224HR handles
107. port 82 TVP 224HR User s Guide Operation 1 Pick up this analogue telephone set You should be able to hear the dial tone provided by the TVP 224HR 2 The corresponding green LED will light up when the telephone set is picked up For Example If the telephone set is connected to the second port of FXS When you pick up the telephone set the second green LED will light up 3 We can dial the desired destination phone number at the telephone set If the desired destination phone number is legal the TVP 224HR will play two quick address ack tones Du Du to destination If the desired destination phone number is illegal the TVP 224HR will play three out of service tones please check the dial plan and your desired destination phone number 10 3 Making a call with TVP 224HR FXO Port Connection Analogue PBX connects to FXO port Operation 1 Pick up this analogue telephone set you can hear the PBX dial tone provided by the PBX system E In some cases you have to dial a specific number to get the connection between telephone set and PBX J Dial the extension number for the gateway as provided by the PBX for the TVP 224HR FXO port When the TVP 224HR is connected the corresponding green LED will be illuminated For Example If the telephone set is connected to the second FXO port the second LED will be green We can dial the desired destination phone number on the telephone set If the desired
108. s 60 248 111 217 Subnet Mask 255 255 255 0 EE gs Line Settings Default Gateway 160 248 111 254 Y Administration 5 Help Primary DNS server 168 95 1 1 Secondary DNS server 10 0 0 0 Figure 18 Internet Access Fixed IP Configuration Menu Fixed Dynamic IP Address If your access method is Fixed IP no login a screen like the following example will be displayed when the Fixed IP button is clicked 41 br Home Epe Internet Access B Fixed IP B DHCP Client TVP 224HR VoIP Gateway Router Fixed IP Network Settings IPAddress 60 248 111 217 Subnet Mask 255 255 255 0 Default Gateway 60 248 111 254 Primary DNS server 168 95 1 1 Secondary DNS server 0 0 0 0 Figure 19 Connection Details Fixed Dynamic IP Address Data Fixed Dynamic IP address Screen Internet IP Address The IP Address of this device as seen by Internet users This address is allocated by your ISP Internet Service Provider Subnet Mask The Network Mask associated with the IP Address above Default Gateway The IP Address of the remote Gateway or Router associated with the IP Address above DNS IP Address The IP Address of the Domain Name Server which is currently used Secondary DNS The IP Address of the Backup Domain Name Server if the primary Server should fail Buttons OK Click on Ok once your information has been filled in You will also have to reboot the device in order for the changes to take effect 42
109. s of your MAC address located on the bottom of your TVP 224HR 00 50 2d xx xx xx At the Console prompt enter the super password without hyphens The password is all lower case After gaining access at the console prompt type in net set manager password lt new_password gt lt new_password gt net store net reset If entry of new password is successful the console will list OK You will now be able to gain Web Access from a PC in the same local segment using the TVP 224HR LAN IP Address If Web and or Telnet Access are enabled you will also be able to remote access the TVP 224HR by entering http followed by the TVP 224HR WAN IP or domain name At the prompt Console gt Enter ping 168 95 1 1 Consoles ping The following dialogue indicates that Internet R 168 95 1 1 Access is successful 115 TVP 224HR User s Guide Ping 168 95 1 1 1 out of 1 pings succeeded Console gt If the ping times out you do not have Internet Access Please refer to the trouble shooting section of the User Manual or consult your ISP to make sure your Internet Access Data is correct and accurately entered into the TVP 224HR The following commands enable disable web and telnet access respectively Net set http lt on off gt Net set telnet lt on off gt Console gt on off To reset to Factory Default settings please perform the following commands to Erase all port code
110. sctsccecedecsvasacsecessscestucbestostasadistssdntdecdesecssenesabbosceseiuebsoscsdesvesaiseiees ci e Tiri isane 41 Internet Access Configuration sssesesesecceeosoesesesecoesosoeseserocoesoroesesecoceesoroesesecoeeosoroesesecoeeosoesese 41 Fixed Dynamic IP AddYress scsccscssessssssssscsscsscescsssesssssneseesessossessessessnesssssessessessosseses 41 PPPoE Configuration s iscsscieciscoassessoassessovsnsonsevessesinesesanseesocasseasscnssasecsosissonsoussanssendoseas onbeseasons 43 Special Applications 48 wae a Who A Rae 44 MZ ease Po do e es an a ulcer aa ce ore 0 dos 45 Dynamic DNS Domain Name Server cscssssssscssscssccsscsscecscssecssecsscscscssscssssssssssssesssees 45 Dynamic DNS Screen o isla 46 Virtual Servers Port Forwarding sessessesessoesesoossesoessoscesoesesoossesoessescesoesessossesoessesoesossesso 47 IP Address seen by Internet US TS ooonoonoccnoccnoccoonconnconoconconncon cono nono nonnnonnnnn ron nro rro nro nr rn nnnn nro 47 Virtual Servers Cr od ed e ed 48 Connecting to the Virtual Servers nperi aeres nense a A a aariat 48 RILE O Lio EEE NN 49 Voice DOS AM A A a 49 CHAPTER 7 ADMINISTRATION ococcccccccconoccccncnnnnnnnnnnnnnnnnnnnnnnnnnananannnns 51 IS O ONO 51 Administration Password Setup Login sessessesoossesessoesessossesoosoesessossesoossesoesossessossesssssesose 51 Remote Administration e sessesessoesesoossesoosoesessossesoossesoessesessossessossesoessesessoesess
111. se of your new TVP 224HR The TVP 224HR is a multi function device providing the following services Shared Broadband Internet Access for all LAN users A A J A de a CTO Internet Broadband sey A Modem windows Mac Unix Fast Ethernet Figure 1 TVP 224HR The TVP 224HR is a cost effective and highly reliable analog Voice over IP VoIP Gateway Router that offers toll quality voice and real time fax data over IP networks With its embedded architecture the gateway is ideal for VoIP applications associated with Remote Office and Branch Office ROBO environments With its built in user friendly interface the gateway may be installed easily and conveniently to yield immediate cost savings One VoIP Gateway supports up to four voice or Fax communications simultaneously Implemented with an efficient Real Time Operating System RTOS and flash memory the TVP 224HR provides upgradeable capabilities so it may be programmed with updated firmware locally or via the network at any time It comes equipped with remote management capabilities configurable signaling to work with PBX KTS and or telephone The TVP 224HR utilizes advanced VoIP related technology It includes various voice codecs and fax algorithms echo cancellation Voice Activity Detection VAD Comfort Noise Generation CNG and lost packet recovery algorithms 12 Setup Internet Access Features Shared Internet Access All users on the LAN or WLAN can access th
112. sible analog phone PBX PSTN integration applications of the Gateway Disconnect cadence O provided by your phone company for your PSTN line and disconnect cadence provided by your PBX may require additional matching with the gateway This will require the assistance of your PBX supplier and or Systems Integrator Please also see User s Guide for additional information 10 6 VoIP in a Dynamic IP environment Internet Access 92 TVP 224HR User s Guide The previous section dealt with the TVP 222H in and its configuration in a static IP environment The following section will address the issue of Dynamic IP and the TVP 224HR deployment in such an environment This section we will shows you how to connect two TVP 224HR in a dynamic IP address environment and configure PPPoE DHCP and DDNS clients 10 7 PPPoE DHCP and DDNS clients In addition to fixed IP the TVP 224HR can be configured to use PPPoE or DHCP clients With PPPoE and DHCP you will under most circumstances be assigned a Dynamic IP In order for other people and devices to locate you they will need to be pointed to your dynamic IP Therefore it is necessary that you register with a DDNS Note www dyndns org is currently the only service supported Once you have registered an account and have configured the DDNS client in the TVP 224HR the TVP 224HR will automatically notify DynDNS of your changing IP Address DynDNS will in turn map your Dynamic IP to your reg
113. sscsssscessscssssnsscesssssescnssnessssnessesscssosssssessessnessessessossossosees 110 Appendix A Technical Specifications 111 TVP 224HR Technical Specifications ccecccesecssecseeeseeeseeeeceeeceesensecnsecesecsaeeaecsaeeneeenes 111 Console POL 2 5 a 113 LAN POterio EA EEIEIEE cae cutestentudas cdbeuves tented AER 113 FXO Port Pin Assignment see e a aa n a ra E Aai iseia 114 FXS Port Pin Assi gninent esen i EE A E EES 114 Appendix B Connecting through Console eseesoesessossesoosseseosoesessossesocssesoosoesessossesssssesoes 115 Appendix C Connecting through Telnet eseosoesessossesocsseseosoesessossesocssesoesoesessossesssssesoes 116 Appendix D CLI Commands sseseosossosoossesessoeseosossesoessesoessesessossessossesosssesoesoesessossesssssesose 118 Normal Mode Commands uni A a E 118 Download Mode Commannds cccccceccessessseesecesecesecnecseecaeeeaeceneeeeseensecnseceseceaeenseceeeaeeenes 119 Appendix E Factory Default SettidgS ocmoooooommmss 120 10 Appendix F Worksheets IP Parameters ATPM Destination Table iii aa a Sanh aa TS 122 Remote Desa OO a eA EA a aa N deca NEREO E 123 ATPM Hunt Group Tabla 124 ATPM Address Table io ida EN EREA 125 TINO is 11 Chapter 1 Overview This chapter gives an overview of the 4 ports desktop version VoIP Gateway Router TVP 224HR and a detailed description of its front panel and rear panel Congratulations on the purcha
114. t it should Hint remain on and off when the phone is on hook Now let s test your TVP 224HR that is equipped with 2 FXO interfaces Assume you have one extension line with your PBX system say 201 as the extension number we connect this line to the gateway s port 0 FXO port then connect a telephone phone set to port 3 for example of the gateway 201 316 Pick up your extension handset for example 316 and dial 201 After one ring you should hear a dial tone Now dial 203 The telephone connected to the TVP s FXS port should ring 204 d If you do not hear the dial tone please check the line impedance of your PBX For a TVP 224HR with FXO port please contact your Hint PBX Supplier or System Integrator for further information 1 Now let s make a call to your PBX extension Pick up the handset connected to the FXS port and dial 201 you should hear a dial tone This means that TVP 224HR picks up the line connected to your PBX Then dial 316 your extension handset should ring right away d This guide only uses the default values Once you are familiar with Hint the dial plan set up you may design your own dial plan 10 2 Making a call with TVP 224HR FXS Port TVP 224HR has two FXS ports An FXS port can connect to an analogue phone directly and a FXO port can connect to a PBX system or CO line Connection Analogue telephone set connects to FXS
115. tain DNS server address automatically Use the following DNS server addresses Preferred DNS server o Alternate DNS server Figure 14 TCP IP Properties Win 2000 32 PC Configuration 5 Ensure your TCP IP settings are correct as described below Using DHCP To use DHCP select the radio button Obtain an IP Address automatically This is the default Windows setting Using this is recommended By default the TVP 224HR will act as a DHCP Server Restart your PC to ensure it obtains an IP Address from the TVP 224HR Using a fixed IP Address Use the following IP Address If your PC is already configured check with your network administrator before making the following changes e Enter the TVP 224HR s IP address in the Default gateway field and click OK Your LAN administrator can advise you of the IP Address they assigned to the TVP 224HR e If the DNS Server fields are empty select Use the following DNS server addresses and enter the DNS address or addresses provided by your ISP then click OK 33 Checking TCP IP Settings Windows XP 1 Select Control Panel Network Connection 2 Right click the Local Area Connection and choose Properties You should see a screen like the following 4 Local Area Connection Properties General Authentication Advanced Connect using 89 D Link DFE 530TX PCI Fast Ethemet Adapter rev B This connection uses the follo
116. tering all the information listed in the tables below DO NOT navigate away from Dial Plan Settings Click Store Dial Plan and click YES to save your dial plan to Flash Memory Gateway A and Gateway B Dial Plan Tables Gateway A Telephone Number Table Phone Hunt Min Max Prefix Prefix Function Comment Group ID Digits Digits strip Address None Dialing 203 calls ne on FXS Port Dialing 204 calls phone on FXS Port 87 800 801 01 22 02 TVP 224HR User s Guide Dialing 800 calls This is an example PBX on FXO Portlonly Please 0 which then dials substitute your ext on PBX if applicable Dialing 801 calls This is an example PBX on FXO Portjonly Please 0 which then dials substitute your ext on PBX if applicable Dialing 9 from For PBX on FXO local phone on FXS use only Port connects you FXO Port 0 PBX where 9 is dialed for outside line After receiving 01 For PBX on FXO 8 to 10 digits 2 use only Digit Taiwan Area Code from GW B 01 is stripped prefix address 9 is dialed to PBX on FXO Port 0 for outside line and then remaining 8 to 10 digits are dialed 22 is stripped and Remote Zone remaining 3 digits used to make calls are sent to GW B to remote GW B FXS Internal Ext 02 8 to 11 digits Remote Zone 3 Digit US Area used to make calls 2
117. ternet Connections 2 Select Set up or change your Internet Connection 3 Select the Connection tab and click the Setup button 4 Cancel the pop up Location Information screen 5 Click Next on the New Connection Wizard screen 6 Select Connect to the Internet and click Next 7 Select Set up my connection manually and click Next 8 Check Connect using a broadband connection that is always on and click Next 9 Click Finish to close the New Connection Wizard Setup is now completed Accessing AOL To access AOL America On Line through the TVP 224HR the AOL for Windows software must be configured to use TCP IP network access rather than a dial up connection The configuration process is as follows e Start the AOL for Windows communication software Ensure that it is Version 2 5 3 0 or later This procedure will not work with earlier versions e Click the Setup button e Select Create Location and change the location name from New Locality to TVP 224HR e Click Edit Location Select TCP IP for the Network field Leave the Phone Number blank e Click Save then OK Configuration is now complete e Before clicking Sign On always ensure that you are using the TVP 224HR location 36 PC Configuration Macintosh Clients From your Macintosh you can access the Internet via the TVP 224HR The procedure is as follows 1 Open the TCP IP Control Panel 2 Select Ethernet from the Connect via
118. to confirm new password O Changes to the password from the Web Ul and Telnet are Note effective immediately unless trying to use the new password set in Web Ul and Telent from Console port In this case you would have to reboot the GW before the password would take effect index htm User name Password C Remember my password Figure 26 Password Dialog Enter the default User Name and the Password you set on the Administration Password Setup screen above Remote Administration Remote Administration allows you to connect to this interface via the Internet using your Web browser or Telnet By default both services are activated 52 TVP 224HR User s Guide TVP 224HR VoIP Gateway Router Service Acess Configuration WAN HTTP Web access Enable Disable Telnet Acess Enable Disable Trusted Telnet Clients IP address 00 00 f Help Subnet Mask 0 0 0 0 Ping Reply Enable Disable Figure 27 Remote Administration Screen Data Remote Administration Screen Information Information To establish a connection from the Internet 6 Enable Remote Administration and configure this screen 7 From a remote location start your Browser 8 Inthe Address or Location field enter HTTPS NOT HTTP the Internet IP address of this device NOT the LAN IP address and the port number as follows HTTPS ip_address port_number Where ip address is th
119. tory Default Settings 113 Administration essees 78 Firmware Version ooooocoinccnono 67 AlAs ESen 70 First Digit Wait Time 78 Append Prefix s es 73 Foreign Exchange Office CU 4 61 115 See FXO AUtO ANSWeT coocococcocnocnnonnnonnonnnnos 69 Foreign Exchange Station c See FXS Front Panel oooonnccnnnnincccnnn 14 16 Cse Tiernan neinn 89 FXO ani 4 17 103 CASE i nica 89 FXO Port Pin Assignments 110 Case Sr 90 FXO to FXS PLAR 100 102 Case A T 91 EA 4 17 103 104 O as esate 97 FXS Port Pin Assignments 110 CO 99 FXS to FXO PLAR eee 98 CASE Tonine 101 G Channel Parameters 78 Channel Status 00 0 00 77 79 Gate Keeper 69 70 Clear Dial Plan cece 76 Gate Keeper Address 70 E D IE 4 111 GateKeeper ID 0 0 ee eects 70 CHONS viii indicas 90 Gateway ccccescceseeseceteeseeteeeees 12 A 12 H Codec Selection 77 Code iia dada 64 AA A 4 61 Common Parameters 77 H 323 Configuration 67 COnce pts cccccocccocccononaconcccnnnaconnnonns 61 H 323 ParameterS ccseceeee 68 Console se 109 Heliconia incre prcciass 79 D Hotlines isnie 97 99 101 HTTP setting mode 65 Dial plan oo ee ceeeeseeeteesteeteeees 62 hunt group coooccocccooncconcnononnninnnonoss 62 DDN Secon arenie 90 Hunt Group ID ossee 73 Default Dial Plan
120. up 10 Select Add and DestinationID 11 Enter the following fields a Destination ID 11 b Hostname or IP address 192 168 0 20 c Click on OK Dial Plan Settings Dial in PLAR CID 12 Enter 11201 in the PLAR Address Field 13 Click on OK Dial Plan Settings Store Dial Plan 14 Click on Yes SR ogp From Console Enter Username admin Enter Password 123 or from Windows command prompt Enter telnet 192 168 0 55 Enter Username admin Enter Password 123 atpm req atpm aadd 11 55 112 Lines 4 13 creates a zone number a number that tells GW B to forward to a remote destination for TVP GW A atpm hadd 11211 atpm dadd 11 h323 192 168 0 20 atpm done atpm store set tcid 0 dial_in plar 11201 config activate config store Lines 12 14 setup the hotline PLAR from TVP Gateway B to TVP Gateway A 104 TVP 224HR User s Guide Case 7 PLAR Hotline FXO to FXO example INTERNET TVP Gateway A TVP Gateway B oeoa ES SS FXO 201 FXO 201 Site A PBX PBX Extension XXX PBX Extension XXX J For example 316 J For example 421 e Caller on Site A PBX could pick up any PBX extension Case Scenario Site A PBX Extension Caller 316 wants to be able to pick up phone dial a number and immediately have dial tone on Site B PBX and then be able to call any Site B PBX extension Solution Set up hotline PLAR on TVP Gateway on Site A Usage
121. ures and or should use the default settings For more information please see the Advanced User Manuals or consult with your Systems Integrator TRENDnet TVP 224HR VoIP Gateway Router H 323 General Parameter Settings Display Name _ EA AA AN All blanks between words entered will be replaced by under scores Terminal Type 0255 60 RTP Port Base must be an even number 30000 Outgoing Fast Start Mode off 1 Display Name The default string is Customer This field is to set the display name information that is carried in the H 323 setup messages Up to 48 characters can be entered 2 Terminal Type The default value is 60 This field is to set the H 245 terminal type which is used as part of the master slave determination process of H 245 Typically setting a value of less than 50 will force slave operation and a value of greater than 200 will force the master operation For more details please refer to H 323 related standard documents 3 RTP Port Base The default value is 30000 This field is to select the starting port number for assignment of RTP and RTCP ports According to the H 323 specification RTP port number should be even in value and the RTCP port number should be one greater than the RTP port Typically numbers from 0 to 1023 are reserved on most systems 68 TVP 224HR User s Guide 4 Outgoing Fast Start The default setting is off This field is to enable or disable t
122. versation The above process is the same for Gateway B phone 203 and 204 calls to Gateway A phone 201 800 and 801 Case 2 Gateway Phone to PSTN Phone Gateway B phone 203 calls to PSTN phone A number 7777 1234 Caller Operation at GW B Equipment Operation Receiver Operation at GW A Pick up phone 203 204 on 1 GW dial tone is heard 2 GWB Line 3 LED ON Dial 01 7777 1234 1 Du Du is heard 2 VoIP call processing Ring back tone is heard 1 GW A Line 1 LED ON 2 GW A is connected to PSTN Ring back tone is heard 1 PSTN call processing Phone 7777 1234 is ringing up VoIP Conversation VoIP Conversation The above dialing process is the same for phones 203 204 to any GW A local PSTN phone number 91 TVP 224HR User s Guide Case 3 PSTN Phone to Gateway Phone o Phone A number 7777 1234 calling Gateway B phone 203 Caller Operation at Equipment Operation Receiver Operation at GW Phone A B phone 203 Pick up phone A 1 PSTN dial tone is heard Dial 8888 2222 1 Call being processed 2 PBX plays voice greeting Dial 22203 22204 1 Du Du tone is heard LT 2 VoIP call processing 1 GW A Line 1 LED ON Phone 203 is ringing 1 GW B Line 3 LED ON Receiver Picks up phone 203 VoIP Conversation PtP Conversation The above dialing process is the same for any calls made from GW A local PSTN to remote phone numbers 203 amp 204 Case 1 3 Sample Dial Plans show the pos
123. wing items E Client for Microsoft Networks a QoS Packet Scheduler Internet Protocol TCP IP a File and Printer Sharing for Microsoft Networks Unin tall Description across diverse interconnected networks Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication C Show icon in notification area when connected Figure 15 Network Configuration Windows XP 3 Select the TCP IP protocol for your network card 4 Click on the Properties button You should then see a screen like the following 34 PC Configuration Internet Protocol TCP IP Properties General Altemate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Use the following IP address Obtain DNS server address automatically Use the following DNS server addresses Figure 16 TCP IP Properties Windows XP 5 Ensure your TCP IP settings are correct Using DHCP To use DHCP select the radio button Obtain an IP Address automatically This is the default Windows setting Using this is recommended By default the TVP 224HR will act as a DHCP Server Restart your PC to ensure it obtains an IP Address from the TVP 224HR Using a fixed IP Address Use the following IP Address
124. xx xxx is your ISP provided DNS Server IP or any known Public Internet Address The following dialogue confirms Internet Access Console gt ping 168 95 1 1 ping lt 168 95 1 1 gt 56 data bytes 168 95 1 1 is alive Console gt Ping XXX XXX XXX If the ping times out you do not have Internet Access or the Public IP Address you pinged is incorrect Try another IP Address If you confirm that you do not have Internet Access please refer to the trouble shooting section of the User Manual or consult your ISP to make sure your Internet Access Data is correct and accurately entered into the TVP 224HR 117 TVP 224HR User s Guide Appendix D CLI Commands Normal Mode Commands Command Description atpm aadd Add an entry to the address table atpm adel Delete an entry from the address table atpm afind Find and display an entry in the address table atpm alist Display all entries in the address table atpm dadd Add an entry to the destination table atpm ddel Delete an entry from the destination table atpm dfind Find and display an entry in the destination table atpm dlist Display all entries in the address table atpm hadd Add an entry to the hunt group table atpm hdel Delete an entry from the hunt group table atpm hfind Find and display an entry in the hunt group table atpm hlist Display all entries in the hunt group table atpm done

UG TVP-224HR v7

Contents

Download Pdf Manuals

Related Search

Related Contents