Home

AutoDAB-GO

1. automatically after 3 seconds The selected vacant frequency will be shown at the top right of the display e g TX 108 0MHz 5 Tune your car FM radio system to match the selected vacant frequency for transmission of the audio signal from AutoDAB GO to your car stereo audio system 10 Select FM Transmitting Frequency Manual Mode 1 Press TX SCAN to enter FM transmitting frequency selection mode Then use the Tuning Knob to select the desired vacant frequency which you would like to receive through your car radio Once it is selected press the TX SCAN button to confirm and exit If the TX SCAN button is not pushed within 3 seconds the AUTODAB GO will revert back to normal DAB mode and no changes will be made DAB Search 1 Press the MODE button until DAB mode is found Use the Tuning Knob to select the desired DAB channel Alternatively to view DAB stations in a list press the MENU button Use the Tuning Knob to scroll up or down to select the desired DAB channel and press the MENU button again to select You may also press and hold the TX SCAN button for 3 seconds to re activate the Auto Scan process if you need to update the DAB radio channels 11 Note For normal use you don t have to perform Auto Scan every time you use the car DAB radio unless there are newly added DAB channels in which case you may need to perform Auto Scan again DAB Service Information Relevant service informati
2. confirm by pressing the MENU button to see the current software version of the device Press the MODE button to exit menu 20 Technical Specifications Radio Frequency Ranges Power Supply Antenna Power Supply Bluetooth Speaker Output Output Connectors Dimensions Net Weight DAB DAB DAB Band III 174 240MHz FM Transmitter 87 5 LO8MHz Micro USB 5V SV 1 5A Version 2 1 1 0W 8 Q 3 5mm Stereo Jack for Audio 96mm x 75mm x 248mm 128g Information in this user manual is subject to change without prior notice 21
3. AUTODAB eo digital radio on the move NP English AutoDAB GO Digital In Car DAB Digital Radio with FM Transmitter amp Bluetooth Hands Free digital radio on the move This manual is also available in the following languages via www autodab com go instructions Dansk Fran ais Deutsch Italiano H Nederlands Norsk Safety Instructions AN Warning e Do not expose this radio to rain or moisture e Obey local traffic laws and do not use whilst driving e Clean with a dry cloth e Do not block any ventilation openings e Donot use near heater vents e Use accessories provided by manufacturer e Donot leave your radio where excessive heat could cause damage Contents 4 6 7 10 11 12 13 14 18 19 21 Controls and Connectors Operating the AutoDAB GO DAB Antenna Installation Selecting Audio Output DAB Search DAB Service Information Preset Stations Bluetooth Aux In Settings Technical Specifications 3 Controls and Connectors IAN Em mN digital radio on the move Bluetooth Controls 1 Power On Off Switch 2 3 5mm Line In or Line Out 3 Tuning Knob 4 MODE Button 5 TX SCAN Button 6 MENU Button 7 PRESET Phone Play Pause Button 8 Microphone 9 Power Supply Cable Socket 10 Antenna Jack Main unit and Accessories 1 Main Unit DAB receiver 2 Power Supply Cable 3 3 5 mm Audio Cable 4 Power Amplified Internal DAB Antenn
4. a 5 Suction Cup Mount Holder 6 Dual USB Car Charger with 12V Socket Note All accessories are designed to work specifically with AutoDAB Go Please do not use third party cables as these may not work and cause warranty invalidation Operating the AutoDAB GO 1 Mount the AutoDAB GO on the dashboard using the provided suction cup holder Connect one end of the USB power supply cable to the Micro USB socket on AutoDAB GO and the other end to the dual USB car charger Plug the dual USB car charger into the car 12V power socket Connect the supplied antenna to the antenna socket Turn on the power with the POWER SWITCH and the display will show AutoDAB Digital Radio on the Move Use MODE button to select DAB mode For first time use you need to scan all the local DAB channels by pressing and holding TX SCAN button for 3 seconds to activate Auto Scan All available DAB radio channels will be scanned and saved until another Auto Scan is performed During scanning a percentage bar will be shown on the display to indicate the progress and the total number of channels available will be displayed Once scanning is complete you can select any DAB radio channel via the Tuning Knob DAB Antenna Installation Antenna Film Amplifier Block gt Earth Sheet Antenna Lead gt DAB Antenna Diagram 15cm The antenna should be fitted on the passenger side of the front windscreen Ensure that there is a 15cm g
5. ap at the top of the antenna film and a 5cm gap from the side of the windscreen to the vertical strip of the antenna film as shown Wipe the inside of the windscreen were the antenna is to be fitted If glass is cold you may need to warm the glass to ensure good adhesion Ensure the glass surface is dry before mounting the antenna film Remove the adhesive backing and stick the lower horizontal section of the antenna film to the windscreen Be careful not to touch the sticky side of the antenna film Stick the antenna to the glass gently applying pressure to remove any air bubbles Remove the adhesive backing from the amplifier block on the antenna lead ensuring that you do not touch the terminals or the sticky surface Remove the adhesive backing from the earth sheet on the amplifier block and stick this to the metal of the A pillar Note that you do not need to remove any paint for the earth contact to work K Position B L gt 7 AutoDAB GO is to be mounted Route the antenna lead down the A pillar to where the Ensure you do not trap any leads as you go Do not attach the DAB antenna above heater wires ina location which would obstruct the view of the driver orina location that would receive interference from metal For your safety do not run cables so that they interfere with operation of the vehicle or through a location that would interfere with the function of the airbags Select
6. ing Audio Output Aux Out 1 Press and hold the MENU button to enter menu mode Use the Tuning Knob and scroll to AUX IN OUT Select and confirm by pressing MENU again Use the Tuning Knob to select AUX OUT and confirm by pressing the MENU button You will then be returned to the source you were previously on A headphone icon will be displayed at the top of the display Connect the supplied 3 5mm Audio Cable to the 3 5mm Line Out connector on the side of the AuUtoDAB GO and then connect to the Aux in of the car stereo Note In AUX OUT mode there will be no FM transmission to the car stereo Selecting Audio Output FM Transmission Select FM Transmitting Frequency Auto Mode 1 Press and hold the MENU button to enter menu mode Use the Tuning Knob and scroll to AUX IN OUT Select and confirm by pressing MENU again Use the Tuning Knob to select AUX IN and confirm by pressing the MENU button This will enable FM transmission mode 2 Press TX SCAN button to show FM transmitting frequency TX Frequency 3 Press and hold TX SCAN button for 3 seconds to activate the automatic scanning of a vacant transmission frequency without interference with other channels The scanning process will take 20 30 seconds and is accompanied by a flashing display of MHZ before stopping at a vacant frequency 4 After a vacant frequency is found press the TX SCAN button again to confirm and exit the setting or this will occur
7. luetooth and search for Bluetooth peripherals A list of available Bluetooth peripherals will be displayed 4 Select CAR DAB in the list and once connection is established the Bluetooth screen will display Connected and a Bluetooth icon will be shown at the top of the AutoDAB GO display 5 In Pairing in Progress mode if you want to stop searching for a new phone you can press the PRESET button to stop searching and return to the last connected phone Note During the process of re connecting to the last connected phone it may up to one minute for 14 re connection depending on the model of the phone In the reconnecting process the Bluetooth icon at the top of the AutoDAB GO display will be flashing and the LCD will show Not Connected You can disconnect an existing connected phone by pressing and holding the TX SCAN button to force the AutoDAB GO into pairing mode to connect another new phone Note The flashing of the Bluetooth icon indicates that a Bluetooth device is not connected Once it is connected the icon will stop flashing Manage Phone Call When there is an incoming call the AutoDAB GO plays a ringtone Press PRESET to answer a call The speaker phone volume and call duration will be displayed at the bottom of the screen You can use the Tuning Knob to adjust the volume level Press and hold PRESET to decline a call To end a call press PRESET Selecting Bluetooth Phone Voice to your Car Stereo thr
8. on data broadcast by the radio station will be displayed with scrolling text on the screen of the AutoDAB GO While listening to DAB the display will show the following if applicable Channel Name Frequency Multiplex Name DLS DAB Icon Number of Channel Scanned and Stored Time Date Signal Strength FM Transmitting Frequency Bluetooth Connection Status Aux In or Aux Out Status oe et ee oe te i e e e 12 Preset Stations Storing Preset Stations To program and store your favourite DAB preset stations 1 Press and hold the PRESET button for 3 seconds to enter Store Preset Stations mode 2 Use the Tuning Knob to scroll up or down to select a number in the memory bank to store your favourite Station 3 Press the PRESET button to confirm and exit Stored Successfully will be displayed Selecting Preset Stations To select your favorite DAB preset stations 1 Press the PRESET button to enter Select Preset Stations mode 2 Use the Tuning Knob to scroll up or down to select a Preset Station 3 Press the PRESET button again to confirm and exit 13 Bluetooth Pairing a Phone When pairing a phone with AutoDAB GO for the first time follow the below procedures 1 Press the MODE button until you scroll the screen to Bluetooth mode 2 Press and hold the TX SCAN button to put the AutoDAB GO device into pairing mode Pairing in Progress will be shown 3 From your phone turn on B
9. ough FM Transmitter or Built In Speaker Press and hold MENU button to enter menu 15 2 Use the Tuning Knob to scroll down the menu and select Phone Speaker Setting Press MENU button to confirm 3 Use the Tuning Knob to select Built in Speaker or Car Speaker and confirm by pressing the MENU button again You will then be returned back to the source you were previously on 4 Use the Tuning Knob to adjust the voice volume to the desired level when it is in Built in Speaker mode 5 When in Car Speaker mode the voice volume can only be adjusted by the car stereo volume control button Car Speaker will be displayed at the bottom of the AutoDAB GO screen Note When the Car Speaker is selected the phone voice can be input into car stereo by either using AUX OUT or FM Transmitter Bluetooth Music Playback FM transmission Mode 1 Ensure Bluetooth mode is selected and a phone is paired Select the music file from your phone and select playback via Bluetooth Refer to your phone user guide for more information 16 2 Make sure you have selected AUX IN mode by pressing and holding the MENU button to enter menu mode Use the Tuning Knob to scroll to AUX IN OUT Select and confirm by pressing MENU again Use the Tuning Knob to select AUX IN and confirm by pressing MENU button 3 Press TX SCAN button to enter FM transmitting frequency selection mode 4 Then use the Tuning Knob to select your desired vacant frequency 5 P
10. ovided 3 5mm audio cable 18 Settings Screen Background Font Colour The colour of the screen background and font can be set to four different combinations to match with your overall car dashboard colour Black background white font Black background blue font Black background orange font Colour oy ha To set the colour follow the procedure below e Press and hold the MENU button for 3 seconds and scroll to Colour Setting e Use the Tuning Knob to scroll and select the desired colour and press MENU button to confirm You will then be returned to the previously selected source LCD display Dimmer Control When driving at night you can control the brightness of the colour LCD display by pressing and holding the MODE button to dim the display Press and hold the MODE button again to return to normal brightness level 19 Language Selection 1 Press and hold the MENU button 2 Use the Tuning Knob to scroll to Language Setting and confirm by pressing the MENU button again 3 Use the Tuning Knob to select your desired language and confirm by pressing the menu button Factory Reset 1 Press and hold the MENU button 2 Use the Tuning Knob to scroll to Factory Reset and confirm by pressing the MENU button again 3 Use the Tuning Knob to select YES or NO for the reset and confirm by pressing the MENU button Software Version Press and hold the MENU button Use the Tuning Knob to scroll to Software Version and
11. ress PRESET button to play or pause the music playback 6 Use the Tuning Knob to select next or previous songs Note A Once your phone is paired to the AutoDAB GO the connection between both devices will be automatically re established each time you enter your vehicle if the AutoDAB GO is powered on AutoDAB GO automatically connects itself to the last phone you used with it If you want to connect AutoDAB GO to another phone you already paired but not the last one you have to first disconnect the last phone by selecting Forget this Device in your phone s Bluetooth Settings menu Then press and hold the TX SCAN button to enter pairing mode again 17 B Youcan pair up to eight Bluetooth devices with AutoDAB GO Aux In The AutoDAB GO features a 3 5mm Aux IN jack on the right hand side External analogue audio source from an iPad iPhone iPod Tablet Android phone or MP3 players etc can be fed wirelessly through the FM transmission into your car stereo audio system To connect an external music player Press MODE button until you see AUX IN displayed on the screen If you can t find AUX IN then press and hold the MENU button to enter menu 1 Use the Tuning Knob to scroll to AUX IN OUT Select press MENU button to confirm 2 Use the Tuning Knob to select AUX IN and confirm by pressing MENU button again 6 Connect an external audio source into the AUX IN jack on the right hand side of AutoDAB GO with the pr

AutoDAB-GO

Contents

Download Pdf Manuals

Related Search

Related Contents